2113 Addendum 3.pdf

May 24, 2021

Addendum No. 3

2021 Kenosha County Courthouse Campus Glass Damage Repairs

Request for Bid #2113

To: All Bidders

From: Kenosha County and InSite Consulting Architects

General:

1) See Alternate “D” in instructions to bidders and Bid Form to provide an alternate deduct price for omitting all work at the PSB south entry doors and sidelights. This omits replacement of doors, frames, glass, and hardware below the bottom of canopy level.

Contractor Questions:

1) Questions: NONE allowed after Friday 5/14/2021

Answer: NONE

Specifications:

1) Section 08 43 13 – Aluminum‐Framed Storefronts ‐

a) Part 1: General

i) 1.2 RELATED REQUIREMENTS, Insert “e. Section 08 71 00 – Door Hardware”

b) Part 2: Products:

i) Change 2.3 Aluminum Doors, a. Type I and, b. Type II: from Wide Stile to Medium Stile, and i. Basis of Design for Kawneer 350 to “Heavy Wall” entrance with ii. Thickness: 2 inches

ii) Add to 2.3 Aluminum Doors, a. Type I and b. Type II: “iii. Optional 12” Bottom Rail required to match existing. “

iii) Section 08 71 00 – Door Hardware: Omit: ‐ “

(c) Other Door Hardware: Storefront manufacturer's standard type to suit application.

(d) Finish on Hand‐Contacted Items: Match existing hardware finish of adjacent doors.

(e) For each door, include exit device, closer, and continuous geared hinge.

(f) Hinges: Match existing hardware

(g) Exit Devices: Panic type ‐ Match existing hardware.

(h) Door Closers: Concealed overhead ‐ Match existing hardware.”

Specifications (continued):

2) Section 08 71 00 – Door Hardware

a) Part 2: Products, 2.7. Panic Devices:

i) Add: “At the KCC and KCAB buildings:” for PD1

ii) Add: “AT THE PSB Building:

PD2 Dorma (Dormakaba) 9700 Series, Medium Stile

Finish: Bronze 613 (Oxidized Satin Oil Rubbed)

Controls: Provide MLR feature retracts the latch using a whisper quiet motor, drawing in the touch bar, thus retracting the latch. The device can be activated by a variety of credentials and can electrically hold/dog the exit push bar in a retracted position during non‐secure hours.

Provide power and controls connections.”

Drawings:

1) A201B: Added Specific Plan Note #7 to the KCAB entry doors shown in south entry view 2/A201B as part of the base bid.

2) A201C: Added Specific Plan Note #7 to the PSB entry doors shown in south entry view 1/A201C as part of the base bid.

3) A201C: Added Addendum #2 tags to elevation 1/201C for Alternate “D” that omits replacement of doors, frames, glass, and hardware below the bottom of canopy level.

4) A203C: Omit new glass in openings 121a, 121b, 122a, and 122b. Add work to re‐set existing glass as shown in the Openings Schedule.

END OF ADDENDUM NO. 3

KENOSHA COUNTY BID #2113

WISCONSIN PAGE 1 OF 1

ATTACHMENT C

REVISED BID OFFER FORM

Vendor:____________________________________________________________________________

Note: The bid specifications and drawings reference some alternate bids that the County has chosen not to pursue. Please ignore these alternate specifications that are not specified on this Bid Offer Form.

Base Bid

Provide all work and materials to complete all work per bid terms, conditions, specifications and drawings.

Alternate Bid

Alternate D – Provide a deduct price to omit all work at the PSB South Entry Doors and Sidelites. This includes aluminum frames, doors, glass, hardware, caulking, and general condition costs.

Amount to deduct from Base Bid

Can complete all work on or before 7/30/2021? Yes_____ No______

If no, please state completion date: _______________________

Bid Bond is included (Required)? Yes_____ No______

Kenosha County is exempt from Federal Excise and Wisconsin Sales Taxes, 77.54(9a)(b) WI Stats.

Kenosha County’s CES number is 008-1020421892-06.

DIVISION 08 - OPENINGS

SECTION 08 43 13 – ALUMINUM-FRAMED STOREFRONTS

ADDENDUM NO. 3

08 43 13.1

COPYRIGHT ICA

KENOSHA COUNTY

COURTHOUSE CAMPUS

GLASS DAMAGE REPAIRS

PART 1: GENERAL 1

1.1 SECTION INCLUDES 3

a. Aluminum-framed storefront, with vision and spandrel glass. 4

b. Infill panels of glass. 5

c. Aluminum doors. 6

d. Weatherstripping. 7

e. Door hardware (Reuse or Match Existing, U.N.O.). 8

f. Perimeter sealant. 9

g. NOTE: This work requires close coordination with other trades. Contractors shall be responsible for 10 familiarizing themselves with all material components of construction adjacent to their trade. Bring 11 all questions to the Architect’s attention immediately. 12

1.2 RELATED REQUIREMENTS 14

a. Section 07 90 00 - Sealants 15

b. Section 08 80 00 - Glass and Glazing 16

c. Section 08 87 23 - Safety and Security Films 17

d. Section 08 88 53 - Security Glazing 18

e. Section 08 71 00 – Door Hardware 19

1.3 REFERENCE STANDARDS 21

a. AAMA CW-10 - Care and Handling of Architectural Aluminum from Shop to Site; 2015. 22

b. AAMA 609 & 610 - Cleaning and Maintenance Guide for Architecturally Finished Aluminum 23

(Combined Document); 2015. 24

c. AAMA 611 - Voluntary Specification for Anodized Architectural Aluminum; 2014 (2015 Errata). 25

d. ASCE 7 - Minimum Design Loads for Buildings and Other Structures; 2010, with 2013 Supplements 26 and Errata. 27

e. ASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate; 2014. 28

f. ASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric); 29

2014. 30

g. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, 31

Wire, Profiles, and Tubes; 2014. 32

h. ASTM B221M - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, 33

Wire, Profiles, and Tubes (Metric); 2013. 34

i. ASTM E283 - Standard Test Method for Determining the Rate of Air Leakage Through Exterior 35

Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen; 36 2004 (Reapproved 2012). 37

j. ASTM E330/E330M - Standard Test Method for Structural Performance of Exterior Windows, 38 Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference; 2014. 39

k. ASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, 40 and Curtain Walls by Uniform Static Air Pressure Difference; 2000 (Reapproved 2016). 41

l. ASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, 42 and Curtain Walls by Uniform Static Air Pressure Difference; 2000 (Reapproved 2009). 43

1.4 ADMINISTRATIVE REQUIREMENTS 45

a. Coordinate with installation of other components that comprise the exterior enclosure. 46

b. Preinstallation Meeting: Conduct a preinstallation meeting one week before starting work of this 47 section; require attendance by all affected installers. 48

1.5 SUBMITTALS 50

a. Product Data: Provide component dimensions, describe components within assembly, anchorage 51 and fasteners, glass and infill, door hardware, internal drainage details. 52

b. Shop Drawings: Indicate system dimensions, framed opening requirements and tolerances, 53 affected related Work, expansion and contraction joint location and details, and field welding 54 required. 55

c. Samples: Submit two samples 2 by 4 inches in size illustrating finished aluminum surface, glass, 56 infill panels, glazing materials. 57

d. Hardware Schedule: Complete itemization of each item of hardware to be provided for each door, 58 cross-referenced to door identification numbers in Contract Documents. 59

08 43 13.2

GLASS DAMAGE REPAIRS

e. Installer Qualifications Statement. 1

f. Warranty: Submit manufacturer warranty and ensure forms have been completed in Owner's name 2 and registered with manufacturer. 3

1.6 QUALITY ASSURANCE 5

a. Manufacturer Qualifications: Company specializing in manufacturing products specified in this 6 section with not less than three years of documented experience. 7

b. Installer Qualifications: Company specializing in performing work of type specified and with at least 8 three years of documented experience and approved by manufacturer. 9

c. Full-Size Mock-up Testing: Have a specimen representative of project conditions tested by an 10 independent testing agency for compliance with specified thermal, structural, air infiltration, water 11 penetration, and sound attenuation criteria. 12

1.7 DELIVERY, STORAGE AND HANDLING 14

a. Handle products of this section in accordance with AAMA CW-10. 15

b. Protect finished aluminum surfaces with wrapping. Do not use adhesive papers or sprayed coatings 16 that bond to aluminum when exposed to sunlight or weather. 17

1.8 FIELD CONDITIONS 19

a. Do not install sealants when ambient temperature is less than 40 degrees F. Maintain this minimum 20 temperature during and 48 hours after installation. 21

1.9 MOCK-UP 23

a. Install storefront window unit as a mock-up including each component being used on the project. 24

b. Assemble to illustrate component assembly including glazing materials, weep drainage system, 25 attachments, anchors, and perimeter sealant. 26

c. Locate on-site where directed by Architect. Mock-up may remain as part of the Work. 27

1.10 WARRANTY 29

a. Correct defective Work within a five-year period after Date of Substantial Completion. 30

b. Provide five-year manufacturer warranty against failure of glass seal on insulating glass units, 31 including interpane dusting or misting. Include provision for replacement of failed units. 32

c. Provide five-year manufacturer warranty against excessive degradation of exterior finish. Include 33 provision for replacement of units with excessive fading, chalking, or flaking. 34

PART 2: PRODUCTS 36

2.1 FRAMING FOR INSULATING GLAZING 38

a. Match Existing Style, Thermally-Broken: 39

i. Basis of Design: Kawneer Company, Inc.; Trifab VG 451T. 40

ii. Vertical Mullion Dimensions: 2 inches wide by 4-1/2 inches deep or match existing. 41

b. For any product not identified as "Basis of Design", submit information as specified for 42 substitutions. 43

2.2 FRAMING FOR MONOLITHIC GLAZING 45

a. Match Existing Style: 46

i. Basis of Design: Kawneer Company, Inc.; Trifab VG 451. 47

ii. Vertical Mullion Dimensions: 2 inches wide by 4-1/2 inches deep. 48

b. Other Manufacturers: Provide either the product identified as "Basis of Design" or an equivalent 49 product of one of the manufacturers listed below: 50

i. EFCO: www.efcocorp.com/sle. 51

ii. Pittco Architectural Metals Inc: www.pittcometals.com/sle. 52

iii. YKK AP America Inc: www.ykkap.com. 53

c. Substitutions: submitted request may be considered. 54

i. For any product not identified as "Basis of Design", submit information as specified for 55 substitutions. 56

2.3 ALUMINUM DOORS 58

a. Type I: Medium Stile, Monolithic Glazing to match existing damaged door: 59

08 43 13.3

GLASS DAMAGE REPAIRS

i. Basis of Design: Kawneer 350 Heavy Wall Entrance Single Acting. 1

ii. Thickness: 2 inches. 2

iii. Optional 12” Bottom Rail required to match existing. 3

b. Type II: Medium Stile, 350-Heavy Wall Insulating Glazing, Thermally-Broken to match existing 4 damaged door: 5

i. Basis of Design: Kawneer AA 425 Thermal Entrance. 6

ii. Thickness: 2 inches. 7

c. Other Manufacturers: Provide either the product identified as "Basis of Design" or an equivalent 8 product of one of the manufacturers listed below: 9

i. EFCO: www.efcocorp.com/sle. 10

ii. Pittco Architectural Metals Inc: www.pittcometals.com/sle. 11

iii. YKK AP America Inc: www.ykkap.com. 12

d. Substitutions: submitted request may be considered. 13

i. For any product not identified as "Basis of Design", submit information as specified for 14 substitutions. 15

2.4 STOREFRONT 17

a. Aluminum-Framed Storefront: Factory fabricated, factory finished aluminum framing members with 18 infill, and related flashings, anchorage and attachment devices. 19

i. Unitized, shop assembly. 20

ii. Glazing Rabbet: For 1 inch insulating glazing as needed to match existing. 21

iii. Glazing Rabbet: For 1/4 inch monolithic glazing as needed to match existing. 22

iv. Glazing Position: Centered (front to back). 23

v. Vertical Mullion Dimensions: 2 inches wide by 4-1/2 inches deep. 24

vi. Finish: Bronze Anodized to match existing. 25

vii. Factory finish all surfaces that will be exposed in completed assemblies. 26

viii. Coat concealed metal surfaces that will be in contact with cementitious materials or 27 dissimilar metals with bituminous paint. 28

ix. Fabrication: Joints and corners flush, hairline, and weatherproof, accurately fitted and 29 secured; prepared to receive anchors and hardware; fasteners and attachments 30 concealed from view; reinforced as required for imposed loads. 31

x. Construction: Eliminate noises caused by wind and thermal movement, prevent vibration 32 harmonics, and prevent "stack effect" in internal spaces. 33

xi. System Internal Drainage: Drain to the exterior by means of a weep drainage network any 34 water entering joints, condensation occurring in glazing channel, and migrating moisture 35 occurring within system. 36

xii. Expansion/Contraction: Provide for expansion and contraction within system components 37 caused by cycling temperature range of 170 degrees F over a 12 hour period without 38 causing detrimental effect to system components, anchorages, and other building 39 elements. 40

xiii. Movement: Allow for movement between storefront and adjacent construction, without 41 damage to components or deterioration of seals. 42

xiv. Perimeter Clearance: Minimize space between framing members and adjacent 43 construction while allowing expected movement. 44

xv. Air and Vapor Seal: Maintain continuous air barrier and vapor retarder throughout 45 assembly, primarily in line with inside pane of glazing and inner sheet of infill panel and 46 heel bead of glazing compound. 47

b. Performance Requirements: 48

i. Wind Loads: Design and size components to withstand the specified load requirements 49 without damage or permanent set, when tested in accordance with ASTM E330/E330M, 50 using loads 1.5 times the design wind loads and 10 second duration of maximum load. 51

ii. Design Wind Loads: Comply with requirements of ASCE 7. 52

iii. Member Deflection: Limit member deflection to flexure limit of glass in any direction, with 53 full recovery of glazing materials. 54

iv. Water Penetration Resistance: No uncontrolled water on interior face, when tested in 55 accordance with ASTM E331 at pressure differential of 8 psf. 56

v. Air Leakage: Maximum of 0.06 cu ft/min sq ft of wall area, when tested in accordance with 57

ASTM E283 at 6.27 psf pressure differential across assembly. 58

08 43 13.4

GLASS DAMAGE REPAIRS

2.5 COMPONENTS 1

a. Aluminum Framing Members: Tubular aluminum sections, drainage holes and internal weep 2 drainage system. 3

i. Glazing Stops: Flush. 4

b. Operable Sash: Aluminum project-out awning; finished to match storefront; turn handle latch with 5 manufacturer's standard insect screen. 6

i. Basis of Design: Kawneer Company Inc.; GLASSvent. 7

ii. Provide insect screens at all locations. 8

iii. Insect screen configured in coordination with the Owner and Architect 9

2.6 MATERIALS 11

a. Extruded Aluminum: ASTM B221 (ASTM B221M). 12

b. Sheet Aluminum: ASTM B209 (ASTM B209M). 13

c. Fasteners: Stainless steel. 14

d. Perimeter Sealant. 15

e. Subsill: Continuous thermally broken subsill and receiver with back and end dams set in full bed of 16 sealant. 17

f. Glazing Gaskets: Type to suit application to achieve weather, moisture, and air infiltration 18 requirements. 19

2.7 FINISHES 21

a. Class I Color Anodized Finish: AAMA 611 AA-M12C22A42 anodic coating not less than 0.7 mils 22 thick. 23

b. Color: Bronze Anodized to match existing. 24

2.8 HARDWARE 26

a. For each door, evaluate the condition of hardware to be salvaged and reused. 27

b. For each door, include new weatherstripping and sill sweep strip. 28

c. Other Door Hardware: Storefront manufacturer's standard type to suit application. 29

d. Finish on Hand-Contacted Items: Match existing hardware finish of adjacent doors. 30

e. For each door, include exit device, closer, and continuous geared hinge. 31

f. Hinges: Match existing hardware 32

g. Exit Devices: Panic type - Match existing hardware. 33

h. Door Closers: Concealed overhead - Match existing hardware. 34

PART 3: EXECUTION 36

3.1 EXAMINATION 38

a. Verify dimensions, tolerances, and method of attachment with other work. 39

b. Verify that wall openings and adjoining air and vapor seal materials are ready to receive work of 40 this section. 41

3.2 INSTALLATION 43

a. Install wall system in accordance with manufacturer's instructions. 44

b. Attach to structure to permit sufficient adjustment to accommodate construction tolerances and 45 other irregularities. 46

c. Provide alignment attachments and shims to permanently fasten system to building structure. 47

d. Align assembly plumb and level, free of warp or twist. Maintain assembly dimensional tolerances, 48 aligning with adjacent work. 49

e. Provide thermal isolation where components penetrate or disrupt building insulation. 50

f. Install sill flashings. Turn up ends and edges; seal to adjacent work to form watertight dam. 51

g. Where fasteners penetrate sill flashings, make watertight by seating and sealing fastener heads to 52 sill flashing. 53

h. Coordinate attachment and seal of perimeter air and vapor barrier materials. 54

i. Pack fibrous insulation in shim spaces at perimeter of assembly to maintain continuity of thermal 55 barrier. 56

j. Install operating sash. 57

k. Set thresholds in bed of grout. 58

l. Install hardware using templates provided form existing or provided for new hardware. 59

08 43 13.5

GLASS DAMAGE REPAIRS

m. Install glass in accordance with Section 08 80 00, using exterior dry glazing method. 1

n. Install perimeter sealant in accordance with manufacturer’s instructions. 2

o. Sealant work to be performed by company specializing in installation of sealant in accordance with 3

Section 07 90 00. 4

p. Touch-up minor damage to factory applied finish; replace components that cannot be satisfactorily 5 repaired. 6

3.3 TOLERANCES 9

a. Maximum Variation from Plumb: 0.06 inches every 3 ft non-cumulative or 1/16 inches per 10 ft, 10 whichever is less. 11

b. Maximum Misalignment of Two Adjoining Members Abutting in Plane: 1/32 inch. 12

c. Glass stops and other framing members shall be installed with hairline joints. Any joint of sufficient 13 width to permit insertion of a credit card (as provided by architect) will be rejected and replaced with 14 member cut to proper length. 15

3.4 ADJUSTING 17

a. Adjust operating hardware and sash for smooth operation. 18

3.5 CLEANING 20

a. Remove protective material from pre-finished aluminum surfaces. 21

b. Upon completion of installation, thoroughly clean aluminum surfaces in accordance with AAMA 609 22

& 610. 23

c. Remove excess sealant by method acceptable to sealant manufacturer. 24

3.6 PROTECTION 26

a. Protect installed products from damage until Date of Substantial Completion. 27

END OF SECTION 08 43 13 29

SECTION 08 71 00 – DOOR HARDWARE

08 71 00.1

GLASS DAMAGE REPAIRS

PART 1: GENERAL 1

1.1. RELATED DOCUMENTS 3

a. Applicable provisions of Division 1 shall govern work under this Section. 5

1.2. DESCRIPTION OF WORK 7

a. This section includes the following and as indicated in the hardware schedule at the end of this 9 section: 10

Hinges 11 Pulls 12 Panic Devices 13 Closers 14 Lock and latch sets 15 Lock cylinders and keys 16 Thresholds 17 Weatherstripping for exterior doors 18

b. Related Sections: 19

i. Division 8 Section 08 10 00 Doors and Frames 20

1.3. QUALITY ASSURANCE 22

a. Single Source Responsibility: Obtain each type of hardware from the same supplier. 24

1.4. SUBMITTALS 26

a. Submit three copies of complete and detailed hardware schedule. Include product data on all 28 hardware items being submitted. The submitted schedule shall use symbol/letter designations and 29 format shown on construction documents hardware schedule. 30

b. Submit three copies of proposed keying schedule indicating clearly how the Owner’s final 31 instructions on keying of locks has been fulfilled. 32

c. Submit sample of each item of finish hardware that differs from that specified. 33

d. Samples submitted may be used on the project and will be delivered to the building site where 34 comparison will be made with other hardware furnished 35

1.5. PRODUCT DELIVERY 37

a. Mark each item as to contents and location in the building for which it is intended. 39

b. Ship prepaid the hardware templates and/or physical hardware, as required, to metal door and 40 frame manufacturers and wood door manufacturers. 41

PART 2: PRODUCTS 43

2.1. FINISH HARDWARE SCHEDULE 45

a. Refer to notes on the drawings for hardware requirements. 47

2.2. ANCHORS AND FASTENERS 49

a. Furnish as required and of proper size for the purpose for which it is intended. 51

b. Anchors in solid material shall be with machine screws in expansion shields. Furnish toggle bolts 52 where walls are not solid material. 53

2.3. HINGES 55

a. Non-removable pins on exterior doors and interior locked doors swinging out. Furnish non-rising 57 pins on all other doors. 58

b. Stainless steel hinges on exterior doors swinging out and steel hinges for all other doors. 59 Exterior Hinge Finish: B.H.M.A. 629, stainless steel metal, satin (US32D). 60

08 71 00.2

GLASS DAMAGE REPAIRS

Interior Hinge Finish: B.H.M.A. 626, satin chromium plated (US26D). 61

c. Number of Hinges: 62

i. Continuous, one per door 63

d. Acceptable Manufacturers: Hager. 64

e. Hinge types: Numbers are of Hager, unless otherwise specified. 65

TYPE DESCRIPTION MFR. NO. 67

H1 Anodized to match frame HAGER 780-157HD 69

2.4. LOCKSETS 71

a. Acceptable Manufacturers: Best 73

b. Reuse and install existing cylinders 74

2.5. LOCK CYLINDERS AND KEYING 76

a. Hardware supplier shall make arrangements for and meet with Owner to determine the various 78 keying requirements. 79

b. Owner will provide cylinders and keying for Project. 80

c. Provide new master key system for Project. 81

d. Master key all locks and cylinders. 82

e. Master key and grand-master key all locks and cylinders with the new Office Building project. 83

f. Furnish five master keys for each master keyed set and three nickel silver change keys for each 84 lock. 85

g. Coordinate the number of grand master keys to furnish with the new Office Building project. 86

h. Furnish five master keys for each master keyed set and three nickel silver change keys for each 87 lock. 88

i. Stamp "DO NOT DUPLICATE" on all keys. 89

j. Furnish visual key control for all cylinders. Stamp proper key symbol on the bow of each key and 90 on the face of the cylinder plug of each cylinder. 91

k. Cylinders shall be supplied by manufacturer of locksets. 92

l. Furnish manufacturer’s standard 6-pin tumbler cylinders. 93

m. Furnish removable core cylinders for all locks. Send control key where directed. Provide six extra 94 cores with keys. Master key extra cores. 95

n. Provide cylinders for Aluminum Entrance systems where scheduled: deadbolts. 96

o. Metals: Construct lock cylinder parts from brass or bronze, stainless steel, or nickel-silver. 97

Aluminum, zinc, or plastic parts are not acceptable. Exposed finish shall match lockset, deadbolt, 98 or exit device. 99

p. Deliver keys to the Owner. 100

2.6. Pulls 102

a. Door Pulls: Numbers are of Reese Enterprises, Inc. 104

TYPE DESCRIPTION MFR. NO. 106

P1 Rockwood BF157 1HD 108

(verify center to center) 109 Finish: Oil Rubbed Bronze 613 110

2.7. Panic Devices 114

TYPE DESCRIPTION MFR. NO. 117

AT THE KCC AND KCAB Buildings: 119 PD1 Von Duprin - 33A 120

08 71 00.3

GLASS DAMAGE REPAIRS

Anodized to match frame 122 AT THE PSB Building: 124 PD2 Dorma (Dormakaba) 125 9700 Series, Medium Stile 126 Finish: Bronze 613 (Oxidized Satin Oil Rubbed) 128

Controls: Provide MLR feature retracts the latch using a whisper quiet motor, 129 drawing in the touch bar, thus retracting the latch. The device can be activated by 130 a variety of credentials and can electrically hold/dog the exit push bar in a 131 retracted position during non-secure hours. Provide power and controls 132 connections. 133

2.8. Closers 137

a. Door Closers: Numbers are of LCN, Inc. 139

TYPE DESCRIPTION MFR. NO. 141

C1 LCN 4040XP SCUSH 143

Install with any necessary mounting plates 144 Bronze to match frames 145

2.9. WEATHERSTRIPPING 147

a. Provide only those units where resilient or flexible seal strip is easily replaceable and readily 149 available from stocks maintained by manufacturer. 150

b. Acceptable Manufacturers: Reese Enterprises, Inc; Zero International; Pemko Manufacturing Co., 151

Inc.; National Guard Products, Inc. 152

c. Weatherstrip sets: Numbers are of Reese Enterprises, Inc. 153

TYPE DESCRIPTION MFR. NO. 155

W1 Jamb and head weatherstrip 775A 157 Door bottom/shoe DB595AU 158

2.10. THRESHOLDS 160

a. Extruded aluminum extending to outside edge of door frames. 162

b. Acceptable Manufacturers: Reese Enterprises, Inc; Zero International; Pemko Manufacturing 163

Co.,Inc.; National Guard Products, Inc. 164

c. Threshold types: Numbers are of National Guard Products, Inc. 165

TYPE DESCRIPTION MFR. NO. 167

T1 Extruded aluminum, thermal break, 5” inches wide NGP 8425 169

PART 3: EXECUTION 171

3.1. INSTALLATION 173

a. Install all hardware in accordance with the Manufacturer's recommendations. 175

b. Drill and tap hollow metal doors and frames for surface applied hardware. 176

c. Remove all applied hardware until painting is completed, then reinstall. 177

d. Locate hardware as follows unless shown otherwise on the drawings: 178

i. Hinges: Continuous from frame head to meeting at threshold. 179

ii. Locksets: 40 inches above the finished floor to centerline of strike. 180

08 71 00.4

GLASS DAMAGE REPAIRS

iii. Stops: Install on door if wall condition is not applicable. 181

iv. Flush Bolts: Edge mount. 182

v. Door Pulls: Center line 42 inches above finished floor. Center between door edge and 183 glazed opening or 5 inches from door edge if no glazing. 184

vi. Push/Pull Latch: Center latch 45 inches above floor with handle up on push side and down 185 on pull side. 186

vii. Deadlatches: Center line 48 inches above finished floor. If used in conjunction with a door 187 pull/push plate, mount deadlock center line 32 inches above finish floor. 188

e. Secure wool pile inserts in kerfs in door edges with white glue and small brads spaced 12 inches 189 on center. 190

f. Install electric strike and run wires concealed to location of owner supplied security access controls. 191

g. Install door weatherstripping continuous without coping at hardware. Mount hardware to be located 192 in the same location over the weatherstripping. 193

3.2. ADJUSTMENT 195

a. Adjust all operating hardware in accordance with manufacturer's recommendations. 197

b. Deliver to Owner all installation and adjustment tools and two copies of each installation sheet 198 furnished with hardware items. 199

END OF SECTION 08 71 00 202

A201B

KCAB SOUTH ELEVATION

SCALE: 1/8" = 1'-0"

ICA NO. KCC 21-001

KE

N

O

SH

A C

O U

N

TY

C O

U R

TH

O

U

SE

C

AM

PU

S

- G

LA

SS

D

AM

AG

E R

EP

AI

R S

C O

U R

TH

O

U

SE

(K C

C

PU

BL

IC

S

AF

ET

Y

BU

IL

D

IN

G

(P

SB

C O

U N

TY

A

D M

IN

IS

TR

AT

IO

N

B U

IL

D

IN

G

(K C

AB

InSite Consulting Architects 115 E. Main / STE 200 Madison, Wisconsin 53703 608-204-0825 608-531-1533 (fax) info@icsarc.com

IN

SI

TE

C

O N

SU

LT

IN

G

A R

C H

IT

EC

TS

NOTE: ALL DIMENSIONS GIVEN

SHALL BE CONSIDERED TO BE

"V.I.F." OR VERIFY-IN-FIELD

FEBRUARY 22, 2021

ISSUED FOR BIDDING

KCAB SOUTH ELEVATION

A201B

A201B

KCAB SOUTH ENTRY VIEW

SCALE: N.T.S.

A201B

A201B

KCAB SOUTH EAST VIEW

SCALE: N.T.S.

E A201B

E

A201B

A201B

KCAB SOUTH WEST VIEW

SCALE: N.T.S.

A A201B

A A201B

X A3xx

A201B

X A3xx

A201B

A201B

KCAB SOUTH WEST VIEW

SCALE: N.T.S.

A201B

KCAB SOUTH EAST VIEW

SCALE: N.T.S.

X A3xx

A201B

X A3xx

A201B

2 2 2

13 TYP.

13 TYP.

13 TYP.

13 TYP.

13 TYP.

13 TYP.

A201B

13 TYP.

13 TYP.

DAMAGE VIEW FROM INTERIOR

B101

B102 B103

B105

B151

B161

B162

B165

B163 B164

B167

B121 B122

B124

B141 B142 B143

B125 B126

B127 B128

B129 B130

B133

B132 B131

#3 5/24/2021 ADDENDUM #3

4 4 4

4 41 4 4

1 6

ENTRANCE GLASS HAS BEEN

REPLACED AND PLYWOOD

REMOVED.

ENTRANCE GLASS HAS BEEN

REPLACED AND PLYWOOD

REMOVED.

B106

111111

11 11 11 11

111111111111

11 11 1111

#1 5/18/2021 ADDENDUM #1

(RE-ISSUED COMPLETE DRAWING)

7 7

#3

AutoCAD SHX Text A301

AutoCAD SHX Text

FIRST FLOOR RENOVATION PLAN

A201C

PSB PARTIAL SOUTH ELEVATION

SCALE: N.T.S.

ICA NO. KCC 21-001

KE

N

O

SH

A C

O U

N

TY

C O

U R

TH

O

U

SE

C

AM

PU

S

- G

LA

SS

D

AM

AG

E R

EP

AI

R S

C O

U R

TH

O

U

SE

(K C

C

PU

BL

IC

S

AF

ET

Y

BU

IL

D

IN

G

(P

SB

C O

U N

TY

A

D M

IN

IS

TR

AT

IO

N

B U

IL

D

IN

G

(K C

AB

InSite Consulting Architects 115 E. Main / STE 200 Madison, Wisconsin 53703 608-204-0825 608-531-1533 (fax) info@icsarc.com

IN

SI

TE

C

O N

SU

LT

IN

G

A R

C H

IT

EC

TS

NOTE: ALL DIMENSIONS GIVEN

SHALL BE CONSIDERED TO BE

"V.I.F." OR VERIFY-IN-FIELD

FEBRUARY 22, 2021

ISSUED FOR BIDDING

PSB - SOUTHWEST

ELEVATION

A201C

A201C

PSB PARTIAL SOUTH PERSPECTIVE

SCALE: N.T.S.

13 TYP.

A201C

PSB INTERIOR OF S. ENTRANCE

SCALE: N.T.S.

C101 C111a C112

C113 C114a

C121a&b C111b

C114b C122a&b

#1 5/18/2021 ADDENDUM #1

(RE-ISSUED COMPLETE DRAWING)

13 TYP.

8 7

#3

#3

#3

#2

#2

ALTERNATE PRICING KEY NOTES ALT. #

· BASE BID IS FOR REPLACEMENT-IN-KIND OF ALL DAMAGED DOOR AND

WINDOW FRAMING, HARDWARE AS NOTED IN PLAN NOTE #7, AND

GLAZING AND ADJACENT MATERIALS.

D. PROVIDE A DEDUCT PRICE TO OMIT ALL WORK AT THE PSB SOUTH

ENTRY DOORS AND SIDELITES. THIS INCLUDES ALUMINUM FRAMES,

DOORS, GLASS, HARDWARE, CAULKING AND GENERAL CONDITIONS

COSTS.

ALT. D

ALT. D

#3 5/24/2021 ADDENDUM #3

(RE-ISSUED THIS DRAWING)

AutoCAD SHX Text A301

GLASS DAMAGE REPAIR - PUBLIC SAFETY BUILDING - OPENING SCHEDULE

GLASS

REPLACEMENT

SCHEDULE FOR

KENOSHA

COUNTY

COURTHOUSE

CAMPUS Updated: 5/21/2021

PSB

KENOSHA

COUNTY

PUBLIC

SAFETY

BUILDING

South - 2nd C101 1" IGU ~ 38 x 68 Win-Fix

South - Entry C111a 1" IGU ~ 16 x 58 Sidelite South - Entry C111b 1" IGU ~ 16 x 29 Sidelite

South - Entry C112 1" IGU ~ 28 x 77 Door ADA Operator / CR (confirm) South - Entry C113 1" IGU ~ 28 x 77 Door

South - Entry C114a 1" IGU ~ 16 x 58 Sidelite South - Entry C114b 1" IGU ~ 16 x 29 Sidelite

South - Entry C121a * RE-SET EXIST. Sidelite * RESET EXISTING GLASS IN NEW FRAME South - Entry C121b * RE-SET EXIST. Sidelite * RESET EXISTING GLASS IN NEW FRAME South - Entry C122a * RE-SET EXIST. Sidelite * RESET EXISTING GLASS IN NEW FRAME South - Entry C122b * RE-SET EXIST. Sidelite * RESET EXISTING GLASS IN NEW FRAME

East - 2nd C200 1" IGU ~ 38 x 68 Win-Fix East - 2nd C201 1" IGU ~ 38 x 68 Win-Fix East - 2nd C202 1" IGU ~ 58 x 68 Win-Fix East -1st C203 1" IGU ~ 58 x 48 Win-Fix

ICA NO. KCC 21-001

KE

N

O

SH

A C

O U

N

TY

C O

U R

TH

O

U

SE

C

AM

PU

S

- G

LA

SS

D

AM

AG

E R

EP

AI

R S

C O

U R

TH

O

U

SE

(K C

C

PU

BL

IC

S

AF

ET

Y

BU

IL

D

IN

G

(P

SB

C O

U N

TY

A

D M

IN

IS

TR

AT

IO

N

B U

IL

D

IN

G

(K C

AB

InSite Consulting Architects 115 E. Main / STE 200 Madison, Wisconsin 53703 608-204-0825 608-531-1533 (fax) info@icsarc.com

IN

SI

TE

C

O N

SU

LT

IN

G

A R

C H

IT

EC

TS

NOTE: ALL DIMENSIONS GIVEN

SHALL BE CONSIDERED TO BE

"V.I.F." OR VERIFY-IN-FIELD

FEBRUARY 22, 2021

ISSUED FOR BIDDING

A203C

PSB OPENING SCHEDULE

5/18/2021 ADDENDUM #1

(RE-ISSUED COMPLETE DRAWING)

#3

#1

#3 5/24/2021 ADDENDUM #3

(RE-ISSUED THIS DRAWING)

AutoCAD SHX Text A301