2_160D611512_77751_NULL_J_13A9381-H_77751_NT_NULL_0001_J_J_0001_441_U_N_Y_N_N_Y_D.PDF

ENGINEERING ORDER

1. ENGINEERING ORDER NO.

13A9381-H

DATE: 20130214 PAGE 1 OF 2 PAGES

2. DWG TITLE

TRAILING EDGE WEDGE ASSY CENTER PANEL

3. DWG CAGE CODE

77751

4. DWG NO.

160D611512

5. NEXT ASSY 6. USED ON 7. OPR CAGE CODE DWG SIZE DWG SHEET(S) AFFECTED LATEST DWG REV LTR

160D611511 A-10A #1 & UP, A-10A FATIGUE 98747 J ALL J

8. TYPE OF ENGINEERING ORDER 9. REASONS FOR CHANGE 11. DOCUMENTS AFFECTED (TO / TCTO / SPEC / OTHER): 14. CORROSION CONT MON//ENVIRON. SYMBOL

DATE

ADVANCE CHANGE ERROR CORRECTION

DEVIATION AUTHORIZED DESIGN CHANGE

X CHANGE NOTICE DRAWING CLARIFICATION 15. NDI SYMBOL DATE

INFORMATION X UPDATE DRAWING

AESO 12. EO PREPARED/REQUESTED BY SYMBOL DATE 16.CONFIGURATION MGMT SYMBOL DATE

10. DISPOSITION OF SPARES OTHER COMMENTS:

FA8202-09-D-0003-0011

A. Shepherd, NGC NGTS

REWORK PHONE 17. DWG CHANGED BY SYMBOL DATE

MODIFY (801) 774-3078

SCRAP 13. ENGINEERING APPROVAL SYMBOL DATE 18. CHANGE CHECKED BY SYMBOL DATE

REPLACE Jack L. Miner AFLCMC/

WWAE

PHONE 19. EO / DWG RELEASED BY SYMBOL DATE

(801) 777-4307

20. DESCRIPTION OF CHANGES / REMARKS 21. GOVERNMENT CHECKED BY SYMBOL DATE

AF IMT 3925, 20030819 (V1) REPLACES AF FORM 2600, 19940701, WHICH IS OBSOLETE

1. DESIGN ACTIVITY TRANSFER TO CAGE CODE 98747 SHEET 1:

DESIGN ACTIVITY IS TRANSFERRED TO CAGE CODE 98747,

OGDEN AIR LOGISTIC COMPLEX

HILL AFB, OGDEN, UT 84056

2. UPDATE DISTRIBUTION STATEMENT D, DESTRUCTION NOTICE, AND WARNING NOTATIONS ON SHEET 1 (as shown below).

3. INCORPORATE ALL OUTSTANDING E.O.’S: 04C0566, 05A1254, 06A0670, 06A0679, 07A1021, 08A0003, 09A2943, 09A3385 AND 12A1039-H

4. CREATE 3D MODEL(S) FROM 2D DEFINITION FOR 160D611512-1, -2, -3, -4, -11, -12, -13, -15, -17, -18, -19 AND -20 CONFIGURATION.

5. ADD FLAG NOTE X TO LINK MODEL TO DRAWING:

X. GEOMETRIC DEFINITION ON DRAWING IS NOW CONTROLLED BY 3D MODEL 160D611512-1, -2, -3, -4, -11, -12, -13, -15, -17, -18, -19 AND -20.

ALL NOTES AND TOLERANCES ON DRAWING AND/OR PARTS LIST ARE STILL APPLICABLE.

DISTRIBUTION STATEMENT D: Distribution authorized to Department of Defense and U.S. DOD contractors only, for administrative and operational use. Date of determination is 26 July 2011. Refer other requests for this document to A-10 Engineering Authority, Hill AFB, UT 84056.

DESTRUCTION NOTICE: For classified documents, follow the procedures in DOD 5220.22-M, Industrial Security Manual, Section 11-19 or DOD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents or reconstruction of the document.

WARNING: This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751 et seq.) or Executive Order 12470. Violations of these export laws are subject to severe criminal penalties.

1458153848E block 1 new

1458153848E block 2

ENGINEERING ORDER

(Continuation sheet)

1. ENGINEERING ORDER NO.

13A9381-H

DATE: 20130214 PAGE 2 OF 2 PAGES

2. DWG TITLE

TRAILING EDGE WEDGE ASSY CENTER PANEL

3. DWG CAGE CODE

77751

4. DWG NO.

160D611512

5. DESCRIPTION OF CHANGES / REMARKS:

AF IMT 3926, 20030819 (V1) REPLACES AF FORM 2601, 19940701, WHICH IS OBSOLETE

6. ADD FLAG NOTE CALLOUT TO ALL DETAIL PARTS LISTED IN NOTE X (above). FLAG NOTES SHALL BE PLACED TO THE LEFT OF EACH DASH NUMBER PARTS LIST LINE, AND AT LOCATION WHERE DASH NUMBERS 160D611512-1, -2, -3, -4, -11, -12, -13 AND -15 ARE DIMENSIONALLY

DEFINED.

7. ADD NOTE TO 3D MODEL BELOW DISTRIBUTION, DESTRUCTION, AND WARNING NOTE:

2D DRAWING WITH A 3D MODEL DEFINITION: THIS DATA SET CONTAINING THE 3D REPRESENTATION OF A PART ALONG WITH ITS ASSOCIATED DRAWING, CORRESPONDING PARTS LIST AND NOTES TOGETHER SPECIFY THE COMPLETE “MASTER DEFINITION”.