Attchmt_3_Brand_Name_or_Equal_Specifications.pdf

Solicitation (RFQ) no. 140P8319Q0090, Attachment 2 – Brand Name or Equal Specifications (9/17/19)

Supply & Deliver Hook Lift Water System Unit, OLYM

SPECIFICATIONS FOR HOOK LIFT TRUCK COMPATIBLE WATER TANK SYSTEM

I. SCOPE:

This specification describes an elliptical, with flat side water tank system that is compatible with the single rear axle truck chassis and hook-lift data provided below under Article II (Truck) and Article III (Hook-Lift). Specifications of the water tank and appurtenances are listed below under Article IV. Olympic National Park Maintenance researched this unit from Randco’s website, as a specific manufacturer brand name, for market research and writing this document. Interested Quoters are encouraged to submit quotes for a Randco or equivalent manufacturer’s product that meets the functional characteristics as described herein.

II. EXISITNG TRUCK CHASSIS – 2004 Kenworth T300 (VIN: 2NKMHZ7XX4M066175)

Curb Weight: XX,XXX lbs.

Gross Vehicle Weight Rating (GVWR): 33,000 lbs.

Gross Axle Weight Rating (GAWR): Front, 12,000 lbs.; Rear, 21,000 lbs.

Measurement of truck wheel base: 199”

Measurement from back of truck cab to center of rear axle: 130”

III. EXISTING HOOK-LIFT – Palfinger PLA-10A loader (Serial #: XXXXXXXXX)

Hook height stowed: 5’

Hook in stowed position to center of rear axle: 118”

IV. WATER TANK UNIT

Maximum size tank, at max capacity of water with all appurtenances that does not exceed existing truck GVWR and GAWR for either front or rear axle. Anticipate a tank no larger than 10’ Length x 54” Height x 94” Width, with approximately 2000 gallon capacity or less. If tank at max capacity is near or over the weight ratings of the truck, a legal load valve shall be installed.

Frame for a single axle hook-lift mounted to tank

80” Wide x 36” Deep rear platform

Entire tank welded inside and out

Front and rear heads dished 4”

3/16” heads and baffles. Baffles with 22” crawl holes

¼” steel sub frame with cross members and bolsters

Rubber padded permanent slats welded to tank sub frame

Two (2) lift eyes at top of tank

Rear anti-skid ladder

Solicitation (RFQ) no. 140P8319Q0090, Attachment 2 – Brand Name or Equal Specifications (9/17/19)

Supply & Deliver Hook Lift Water System Unit, OLYM

2.5” hydrant fill to top of manhole

24”x24” manhole

Two (2) view ports: one (1) front and one (1) rear

Tank primer coated

Tank painted white

Tank interior sandblasted and epoxy coated

4x4 Berkeley Pump (B4TQKLS-18) or approved equal installed with battery, fuel tank, and sump. Shall be self-priming – 4x4 – 18hp gas.

Inlet and discharge plumbing installed

Self-loading installed: Two (2) 10’4” storage tubes with 3” suction hose and foot valve installed as a bolt on option

Two (2) rear spray heads (101 valves and splash heads) and rear spray bar manifold for slide-in tank system

Electric over air solenoids mounted to the rear platform, quick connect male and female electrical plug

Cab control plate and switches

Air supply line with male and female quick connectors

1.5” x 50’ hose reel system installed on rear platform

2.5” quarter-turn discharge valve installed with legal load pipe

Actuator with key controls and 17ft lbs. torque: Rowe 3500 series or approved equal

Amber LED beacon light wired into a control box with quick connect electrical fitting

V. MANUALS & ELECTRONIC SCHEMATICS

Vendor shall provide Servicing and Parts Manuals. Manuals shall be provided is the quantity and form of: (1) hard copy and one (1) digital copy of each.

VI. WARRANTY

Manufacturer’s standard commercial warranty documentation/information shall be provided.