Amndmt_1_Attchmt_4_Revised_Brand_Name_or_Equal_Specifications.pdf

Solicitation (RFQ) no. 140P8319Q0090, Amendment 001

Attachment no. 4, Revised Brand Name or Equal Specifications (9/19/19)

SPECIFICATIONS FOR HOOK LIFT TRUCK COMPATIBLE WATER TANK SYSTEM

I. SCOPE:

This specification describes an elliptical, with flat side water tank system that is compatible with the single rear axle truck chassis and hook-lift data provided below under Article II (Truck) and Article III (Hook-Lift). Specifications of the water tank and appurtenances are listed below under Article IV. Olympic National Park Maintenance researched this unit from Randco’s website, as a specific manufacturer brand name, for market research and writing this document. Interested Quoters are encouraged to submit quotes for a Randco or equivalent manufacturer’s product that meets the functional characteristics as described herein.

II. EXISITNG TRUCK CHASSIS – 2004 Kenworth T300 (VIN: 2NKMHZ7XX4M066175)

Curb Weight: 15,220 lbs.

Gross Vehicle Weight Rating (GVWR): 33,000 lbs.

Gross Axle Weight Rating (GAWR): Front, 12,000 lbs.; Rear, 21,000 lbs.

Tare weight on axles: Front, 8,100 lbs.; Rear, 7,100lbs.

Measurement of truck wheel base: 199”

Measurement from back of truck cab to center of rear axle: 130”

III. EXISTING HOOK-LIFT – Palfinger PLA-10M (Serial #: 03C100005)

Hook height stowed: 5’

Hook in stowed position to center of rear axle: 118”

Hook-lift frame length: 15’

*Existing Attachment Measurements for Reference

PLA-10M existing flat deck skid attachment length: 16’3”

PLA-10M existing flat deck skid attachment rear roller to lift frame rear roller distance:

32”

IV. WATER TANK UNIT

Maximum size tank, at max capacity (or near with legal load valve) of water with all appurtenances that does not exceed existing truck GVWR and GAWR for either front or rear. Proposed tank dimensions shall be proposed to be compatible with ratings and dimensions of existing equipment provided in Article II and III.

Legal load valve

Frame for a single axle hook-lift mounted to tank

Solicitation (RFQ) no. 140P8319Q0090, Amendment 001

Attachment no. 4, Revised Brand Name or Equal Specifications (9/19/19)

80” Wide x 36” Deep rear platform or proposed size due to truck/lift frame limitations

Entire tank welded inside and out

Front and rear heads dished 4”

3/16” heads and baffles. Baffles with 22” crawl holes

¼” steel sub frame with cross members and bolsters

Rubber padded permanent slats welded to tank sub frame

Two (2) lift eyes at top of tank

Rear anti-skid ladder

2.5” hydrant fill to top of manhole

24”x24” manhole

Two (2) view ports: one (1) front and one (1) rear

Tank primer coated

Tank painted white

Tank interior sandblasted and epoxy coated

4x4 Berkeley Pump (B4TQKLS-18) or approved equal installed with battery, fuel tank, and sump. Shall be self-priming – 4x4 – 18hp gas.

Inlet and discharge plumbing installed

Self-loading installed: Two (2) 10’4” storage tubes with 3” suction hose and foot valve installed as a bolt on option

Two (2) rear spray heads (101 valves and splash heads) and rear spray bar manifold for slide-in tank system

Electric over air solenoids mounted to the rear platform, quick connect male and female electrical plug

Cab control plate and switches

Air supply line with male and female quick connectors

1.5” x 50’ hose reel system installed on rear platform

2.5” quarter-turn discharge valve installed with legal load pipe

Actuator with key controls and 17ft lbs. torque: Rowe 3500 series or approved equal

Amber LED beacon light wired into a control box with quick connect electrical fitting

V. MANUALS & ELECTRONIC SCHEMATICS

Vendor shall provide provide Servicing and Parts Manuals. Manuals shall be provided in the quantity and form of: (1) hard copy and one (1) digital copy of each.

VI. WARRANTY

Manufacturer’s standard commercial warranty documentation/information shall be provided.