A04_Statment_of_Work_Expedition_SUV.pdf

Statement of Work: Law enforcement vehicle installation / up-fitting.

Date Submitted

Vehicle: SUV Govt. Plate:

VIN:

Notes on equipment for installations:

All equipment needed for installation will consist of new parts unless noted as PROVIDED.

The BLM will be responsible for the cost of a new part above and beyond the initial quote if any part is found to be unusable at the time of installation. However, the vendor will be required to notify the BLM of any unusable part, suggested replacement part, and obtain approval before purchase and installation.

For all new parts needed to complete the installation, as noted below, the vendor must include manufacturer, model, and itemized price of equipment in the quote. All new parts must meet the below set standards or specific make or model as noted or be equivalent. The BLM has the right to disqualify any part that is deemed not comparable or found to be unsatisfactory.

LED Red/Blue Lights: As noted below, for the LED Red/Blue lights the preferred manufacturers are Sound off Signal or Code3. The preferred part is the Sound Off Signal model EMPS1STS3(X) or equivalent.

Vendor will consult with BLM on preferred placement locations prior to installation. The BLM will complete radio installation after the build, but the build must include wiring for the satellite radio and Motorola mobile.

I. STRIP-EXISTING VEHICLE ( XXXXXX ) OF LAW ENFORCEMENT EQUIPMENT

1. Strip all law enforcement (non-OEM) parts from vehicle.

2. Retain all useful parts for install into new, indicated below as

3. All parts not used will be returned to BLM.

4. Remove Existing decals and brown striping.

Plug roof and body holes.

II. INSTALL LAW ENFORCEMENT EQUIPMENT ON NEW VEHICLE

(TBD)

A. BUMPER

1. Install front after-market low profile bumper (if available)

2. Install- One IR light on driver’s side bumper.

3. Install- Front LED driving/sneak lights x2 on dimmer on each corner.

4. Install light bar (ShoMe) on front bumper.

5. Install Rigid spotlight on both sides of light bar.

B. FRONT GRILL/ FRONT QUARTER PANEL

1. Install –Two forward facing LED light heads (red/blue with clear lens, see above for note on preferred make and model) with mounts on grill.

2. Install - Two side facing LED light heads, surface mount / low profile lights (red/blue with clear lens, see above for note on preferred make and model) on left and right front quarter panel.

3. Install –Siren 100w or greater speaker behind grill or compatible location.

4. Install -Wig-Wag Flasher Control for high beam headlights.

5. Install- Quick disconnect jumper cables to bumper- wired to protect emergency lighting and OEM electrical system.

TAILGATE/REAR QUARTER PANEL

1. Install -Two Hide a Blast Tri Color LED Inserts in taillights.

2. Install - Two red/blue LED lights surface mount / low profile (red/blue with clear lens) mounted to rear tailgate.

3. Install - Two red/blue LED lights surface mount / low profile (red/blue with clear lens, see above for note on preferred make and model) mounted to rear side windows.

4. Install- One directional warning bar (red/blue/orange with clear lens, see above for note on preferred make and model) inside rear window.

5. Install rear Anderson plug for wench.

ROOF/HOOD

1. Install - Light bar with full front white abilities.

2. Install - Radio antennas (1)

a. Motorola Radio Antenna

b. Cellular Booster Antenna

3. Install - “Sat-Rad”/GPS dome/disc Radio system antenna.

4. Install run cool semi long louvers on hood.

5. Install – one off road driving spotlight with side alley lights on each A pillar near hood with larger mounting bracket.

INSIDE WINDSHIELD / DASH

1. Install – Cellular Booster 4G/5G.

2. Install– One LED Dome light (red/white). Overhead center console in driver area

3. Install – Speaker microphone magnetic mount (x1) to dash/console.

4. Install --magnetic clip mount x2on SatRad hand-held microphone and Radio microphone.

CENTER CONSOLE

1. Install - Floor plate between seats for mounting console.

2. Install – Center Console unit with Ticket book/cup holder (preferably Troy)

3. Install – Wiring for Motorola XTL8000 mobile radio (Face plate will be mounted on console, remote radio head will be mounted behind front passenger seat attached to prisoner cage)

4. Install wiring for Satellite Radio / mic. Mic and crossband mounted on console.

5. Install- Adjustable mounting hardware/system for “HAVIS” laptop cradle.

6. Install – “HAVIS” laptop cradle to mounting system.

7. Install – Leave Additional Space/plates for additional radio(s), if applicable.

8. Install - Single Unit Siren control box with PA mic/system.

9. Install– Wiring for Satellite Radio / mic. (Mic and cross band will be mounted on console, main radio system will be mounted behind front passenger seat mounted on prisoner cage.

10. Install- rear light cut out switch.

11. Install – Control Switches for accessories on or near console:

a. Front off-road driving lights.

b. IR Light

c. Sneak light Dimmer Switch

d. Rear brake light/reverse light cutouts

e. Rear Prisoner Light

f. Gun Locks X2

g. Alley Lights

h. Takedown Lights

i. Directional Bar (rear window)

12. Install - 12 volt, 3 plug auxiliary power ports x 2

13. Install- 12-volt power invertor.

14. Install – Flush mount 2 port USB charge socket.

15. Install –Ignition override / “Secure Idle” switch with button installed at front top of center.

console or on dash.

16. Install – Stream light Flashlight and Charger.

17. Install – Hidden ignition kill switch.

18. Install --Remote start/keyless entry.

ENGINE COMPARTMENT or VEHICLE INTERIOR 911circuits. (http://www.911circuits.com/ch15-1) or equivalent.

1. Install - Charge guard system to prevent battery drain when minimum voltage is reached (minimum voltage has ability to start truck)

2. Install - Circuit breaker, with ability to disconnect emergency equipment from OEM electrical system.

3. Provide Master auxiliary power/fuse block or box for all aftermarket electronics to access fuses (all fuses labeled) that is easily accessible. (Can be mounted in vehicle interior if necessary).

BEHIND CONSOLE

1. Install – Rifle and shotgun custom mount and 2 locks (BlackRac Locks) with a 10 second timer. Some modification may be necessary to current gun racks for mounting.

2. Install – double gun lock switch that control both gun locks, with one switch hidden near passenger seat and one switch on top of console (can be part of single unit siren control box).

Additionally, gun locks disabled without key in ignition.

http://www.911circuits.com/ch15-1

PRISONER TRANSPORT CAGE The preferred product to accomplish the following is manufactured by setina.com, OR equivalent.

1. Install- Single prisoner transport cage in right rear passenger seat position.

2. Install- Steel window barrier on right rear door window.

3. Install -Steel door panels on both sides.

4. Deactivate- Right rear passenger door lock and window controls but leave operable from driver door controls.

5. Install- Rear / downward facing white LED flush / low profile mounted into prisoner cage.

FRONT WINDOW/WINDSHIELD

1. Install – 30% High quality Window tinting on front driver and passenger side windows.

2. Install – 30% High quality Visor strip window tint on windshield.

REAR CARGO AREA

1. Install – truck vault three drawer with simplex locks.

SUSPENTION/TIRES

1. Install Icon series rear coil over shock with remote reservoir.

2. Install Icon series front coil over shock with remote reservoir.

3. Install aftermarket front upper control arms.

4. Install aftermarket all black rims with proper offset for suspension of 18x9 +20.

5. Install Micky Thompson Baja Boss AT 295/70R17 x5.

VEHICLE EXTERIOR

1. Install striping kit and decals on exterior of vehicle.

2. Install full skid plate if available.