Attachment_7_-_Cable_and_Wire_Ident.pdf

Standard No. S24.803 January 8, 1973

(Revised 07/15/00)

CABLE AND WIRE IDENTIFICATION

1.0 SCOPE

1.1 Scope. This document establishes a standard for the identification of cables and wires to be observed by contractors supplying electronic and electrical equipment or systems.

1.2 Application. The requirements of this standard shall apply to equipment or systems developed or made to Government specifications. The requirements apply to both custom and commercial equipment provided by the contractor in order to satisfy the Government specifications, and to cables and wire connecting such equipment to existing equipment or systems.

1.3 Contracting Officer's Technical Representative. The Contracting Officer's Technical Representative (COTR) shall provide the final interpretation of any conflict between this standard and specific contract requirements.

1.4 Waivers. Any request for waiver of specific requirements of this standard shall be submitted in writing to the COTR and to the Contracting Officer. A request waiver must include: a) identification of the paragraphs for which the waiver is requested; b) identification of the systems, equipment, or components for which the waiver is requested; and c) a discussion of rationale for granting the waiver, including impact on reliability, maintainability, schedule, and cost if the waiver is not granted.

2.0 APPLICABLE DOCUMENTS

None.

3.0 REQUIREMENTS

3.1 General. Cables supplied as part of electronic equipment shall be identified in conformance with this standard.

3.2 Definitions. For the purposes of this standard the following definitions shall apply:

(a) Cable - An interconnecting lead, single or multiconductor, for power, signal, control or grounding.

(b) Intrasystem cable - A cable interconnecting units of the same system or subsystem.

Cables of this category are numbered W0001 through W4999.

(c) Intersystem cable - A cable interconnecting units of two or more major systems or subsystems. Cables of this category are numbered W5000 through W9999.

(d) Cable designator - The letter W used to identify the serial sequence numbers as applying to a listed cable. To further identify cable location an additional letter may be prefixed before the W. Currently assigned letters are:

A GOES Station A (Wallops)

B GOES Station B (Wallops)

C GOES Station C/Redundant (Wallops) 13 Meter Antenna/RF System (Wallops)

D 8 Meter Antenna/RF System (Wallops)

E 7 Meter Antenna/RF System (Wallops)

F 26 Meter Antenna/RF System (Wallops)

G 14.2 Meter Antenna/RF System (Wallops)

HR Hurricane Rated GOES Antennas (Wallops)

I-S Redundant items and interconnection (Wallops)

T Maintenance, test, and development units (Wallops GOES)

T TIROS (Wallops and Gilmore) X GOES/TIROS interconnect and miscellaneous (Wallops and Gilmore).

Z Common or shared units

(Additional assignments will be made as required).

(e) Cable group designator - Cables are grouped according to characteristics and performance. Group classification is denoted by a suffix as listed:

C Control

F RF (radio frequency) and IF (intermediate frequency)

G Grounding

L Logic bits

M Monitor and instrumentation

N Network (Ethernet, FDDI, Internet, etc.)

P Power

PC Patch cords

T Timing

V Video, audio

(Additional assignments will be made as required).

3.3 Marking System. Each cable shall carry an identification number with identification of near-end and far-end termination. Details are given below.

3.3.1 Cable number. In general, blocks of numbers will be assigned to each system or subsystem for application to the cables. These "W" numbers will be selected in accordance with items (b) and (c) of Section 3.2.

3.3.2 Cable identification. Full cable identification, applied to each end of the cable, consists of the following designators in the order listed:

(a) Near-end connector (jack, plug, terminal) number.

(b) Near-end unit (rack) and/or sub-unit (panel or chassis) number.

(c) System designator prefix letter.

(d) Serial ("W") number.

(e) Cable group designator.

(f) Far-end unit or sub-unit number.

(g) Far-end connnector number.

Note: Legends for the two ends of a cable are reverse images, and the near end connector designation is always adjacent to the near end connector. An example is shown in Figure 1.

3.3.3 Cable markers. Cable identification marker strips, as described herein, shall be prepared and affixed to each cable end. The finished cable marker shall present a neat appearance, with the legend visible when the cable is in place.

3.3.3.1 Indoor cables. Cables installed indoors or in a protected environment shall be marked with a self-laminating type label, Thomas and Betts catalog number WTW-2ll2 or WTS-2334, or approved equal. Legends shall preferably be typewritten, however, neat, engineering style, hand-lettering may be used for field prepared labels.

3.3.3.2 Outdoor cables. Cables installed outdoors or in exposed locations shall be of a non-corrosive metallic material with the legend applied by embossing, or a plastic material with the legend applied by engraving.

4.0 CONTROL

4.1 Control. Control of the cable numbering system for each system or subsystem shall maintained by the Contractor's cognizant technical officer. All cable number assignments and changes shall be made under his authority.

4.2 Cable codes. Table 1 lists cable codes to be used in compilation of system cable lists. The codes are purely arbitrary. If a contractor requires a type of cable not included, the list will be expanded to include the new requirement.

4.3 Connector codes. Table 2 lists connector codes to be used in compilation of system cable lists. The codes are purely arbitrary. If a contractor requires a connector not included, the list will be expanded to include the new requirement.

TABLE 1

CABLE CODES

CODE CABLE TYPE

A AWG #8, 2 Conductor Power Cable

B AWG #10, 2 Conductor Power Cable

C AWG #22, Single (1) Twisted Shielded Pair

D AWG #22, Six (6) Individually Twisted Shielded Pairs

E AWG #22, 12 Conductor Overall Shield

F AWG #22, 27 Conductor Overall Shield

G AWG #22, 37 Conductor Overall Shield

H AWG #22, 48 Conductor Overall Shield

I AWG #22, 72 Conductor Overall Shield

J AWG #22, Three (3) Pair, Individually Twisted Shielded Pairs

K AWG #22, Nine (9) Pair, Individually Twisted Shielded Pairs

L AWG #22, Fifteen (15) Pair, Individually Twisted Shielded Pairs

M AWG #20, Single Conductor

N AWG #16, Twelve (12) Conductor

O AWG #12, Twelve (12) Conductor

P AWG #16, Twenty-seven (27) Shielded Pair

Q AWG #20, Fifteen (15) Shielded Pair

R RG-223/U, Coaxial, 50 ohm

S RG-214/U, Coaxial, 50 ohm

T RG-59A/U, Coaxial, 75 ohm

CODE CABLE TYPE

U RG-71/U, Coaxial, 93 ohm

V RG-108A/U, Twinaxial, 75 ohm

W Patch Cord: Trompeter PCW-12-50, 12"/patch plug-to-patch plug/50 ohm

X Patch Cord: Trompeter PCW-6-50, 6"/patch plug-to-patch-plug/50 ohm

Y Patch Cord: Trompeter PCW-6-75, 6"/patch plug-to-patch-plug/75 ohm

Z

AA Coax, Andrew HJA7-50A

BB RG-233/U, Phelps Dodge 1-5/8" Styroflex, 50 ohm

CC RG-232/U, Phelps Dodge 7/8" Styroflex, 50 ohm

DD RG-247/U, Phelps Dodge 7/8" Styroflex, 75 ohm

EE RG-253/U, Prodelin 1/2" Spiroline, 50 ohm

FF RG-254/U, Prodelin 7/8" Spiroline, 50 ohm

GG RG-258/U, Prodelin 1-5/8" Spiroline, 50 ohm

HH AWG #4/0, Single Conductor Stranded, Type TW

II AWG #8, Single Conductor Stranded, Type TW

JJ Braid, Tinned Copper 1/2" flat, AWG No. 36 wires

KK Coaxial, Phelps odge Spirafil II SLA-12-50

LL RG-179/U, Coax, 75-ohm

MM AWG #24, Sixteen (16) Individually Twisted Shielded Pairs

(compatible for EIA Std RS-232C interface)

NN AWG #24, Ten (10) Single Conductors, and Twelve (12) Individually Twisted

Shielded Pairs (compatible for EIA Std. RS-232C interface)

OO AWG #24, Two (2) Individually Twisted Shielded Pairs (compatible for EIA Std. RS-232C interface)

PP AWG #24, Twelve (12) Single Conductors and Three (3) Twisted Pairs

RR AWG #24, Single (1) Twisted Shielded Pair

SS AWG #24, Two (2) Twisted Pairs Overall Shield

TT AWG #24, Fifteen (15) Twisted Pairs Overall Shield

UU AWG #24, Four (4) Twisted Pairs Overall Shield

VV AWG #24, Five (5) Twisted Pairs Overall Shield

WW AWG #28, Twenty-five (25) Conductor Ribbon

XX AWG #28, Fifty (50) Conductor Ribbon

YY AWG #18, Three (3) Conductor

ZZ AWG #18, Ten (10) Conductor a AWG #18, Eleven (11) Conductor b AWG #18, Twelve (12) Conductor c AWG #18, Seventeen (17) Conductor d AWG #18, Twenty-six (26) Conductor e AWG #20, Eight (8) Conductor f AWG #20, Fifteen (15) Conductor g AWG #18, Thirty-seven (37) Conductor h AWG #22, Six (6) Conductor i AWG #22, Twenty-four (24) Conductor j AWG #24, Twelve (12) Conductor k AWG #26, Fifty (50) Conductor l AWG #20, Twenty-Seven (27) Pairs m AWG #20, Seventy-Five (75) Pairs n AWG #18, Six (6) Pairs, Individually Twisted Shielded Pairs o AWG #18, Nine (9) Pairs, Individually Twisted Shielded Pairs p AWG #18, Sixteen (16) Pairs, Individually Twisted Shielded Pairs q AWG #20, One (1) Pair, Individually Twisted Shielded Pair r AWG #20, Three (3) Pairs, Individually Twisted Shielded Pairs s AWG #20, Five (5) Pairs, Individually Twisted Shielded Pairs t AWG #22, Fifteen (15) Pairs, Individually Twisted Shielded Pairs u AWG #18, Six (6) Pairs, Individually Twisted Shielded Pairs v w AWG #22, Five (5) Pairs, Individually Twisted Shielded Pairs x 350004 y 350005 z 350008 aa 350010 bb 350012 cc 350013 dd 350014 ee 350015 ff 350016 gg 350020 hh 350023 ii 310812 jj AWG #2 kk AWG #12, Two (2) Conductor Power Cable ll AWG #12, Three (3) Conductor Power Cable mm AWG #16, Three (3) Conductor Power Cable nn AWG #16, Six (6) Conductor Power Cable oo AWG #16, Seven (7) Conductor Power Cable pp AWG #12, Four (4) Conductor, SO Power Cable qq AWG #2, Four (4) Conductor, SO Power Cable rr RG-218 Coaxial ss 3" Coaxial (Cablewave) 16733-810905-001 HCC 300 505 210 tt 1/2 " Foamflex (Cablewave) 810918-001 FLG uu AWG #20, Nineteen (19) Conductor vv AWG #20, Thirty-seven (37) Conductor ww AWG #20, Three (3) Conductor xx FLC12-50J Coax 50 Ohm Foam Filled yy FSJ1-50 1/4" Coax zz AWG #20, Sixteen (16) Pairs, Individually Twisted Shielded Pairs

AAA AWG #16, Fifty (50) Conductor Overall Shielded

BBB AWG #16, Six (6) Individually Twisted Shielded Pairs

CCC AWG #20, Twelve (12) Individually Twisted Shielded Pairs

DDD AWG #24, Six (6) Individually Twisted Shielded Pairs

EEE AWG #20, Fifty (50) Conductor Overall Shielded

FFF AWG #20, Six (6) Individually Twisted Shielded Pairs

GGG AWG #22, Thirty-Seven (37) Single Conductor Spiral Wrap

HHH AWG #22, Fifty (50) Single Conductors Spiral Wrap

III AWG #16, Eight (8) Conductor

JJJ AWG #20, Twenty-five (25) Conductor

KKK

LLL AWG #16, Four (4) Conductor

MMM AWG #20, Two (2) Pairs, Individually Twisted overall Shielded

NNN AWG #16, Two (2) Conductor

OOO AWG #18, Four (4) Conductor

PPP AWG #18, Eight (8) Conductor

QQQ LDF4-50A Semi-Rigid by Andrews

RRR AWG #24, Twelve (12) Individually Twisted Shielded Pairs

SSS AWG #22, Twenty-Seven (27) Single Conductors, Spiral Wrap

TTT AWG #20, Thirty (30) Conductor

TABLE 2

CONNECTOR CODES

CODE CONNECTOR

1 UG-260D/U Type-BNC, straight plug, RG/U-59

2 Terminal lug, crimp appropriate size to fit wire and stud

3 XL12-3-15 Cannon ITT, Audio

4 MS3106A-36-10P Circular, straight plug, 48 pin, male

5 MS3100A-36-10S Circular, wall receptable, 48 pin, female

6 MS3106A-28-12S Circular, straight plug, 26 pin, female

7 MS3106A-24-5S Circular, straight plug, 16 pin, female

8 UG-88/U Type-BNC, Straight plug, RG/U-58/141/142

9 UG-2lD/U Type-N, Straight plug, RG/U-8/9/213

10 UG-94A/U Type-N, Straight plug, RG/U-11/13

11 UG-536B/U Type-N, Straight plug, RG/U-58/141

12 UG-111/U Type-UHF, Straight plug, RG/U-59/62

13 UG-603/U Type-N, Straight plug, RG/U-59/62/71

14 Dage S004-1 Type-TNC

15 Direct solder to terminals installed

17 P-408-CCT TRW/Cinch Jones Plug, 8 pin

18 200277-4 AMP

20 ZX 13 Printed circuit connector

21 200276-4 AMP

22 320266-8 AMP

23 320663-8 AMP

24 MS3106A-20-3P Circular, Straight plug, 3-pin, male

25 87R Andrew

26 735540 Phelps Dodge, EIA Flange

27 735501 Phelps Dodge, 1 5/8" Type-N, male

28 735502 Phelps Dodge, 1 5/8" Type-N, female

29 735503 Phelps Dodge, 1 5/8" Splice

30 UG/260B/U Type-BNC, Straight plug, RG/U-59/62/71

31 6000 Gremar, Type-TNC, male, RG/U-58/223

32 6005 Gremar, Type-TNC, male, RG/U-59/71

33 5334 Type-N, male, 50 ohm

34 735140 Phelps Dodge, Type-N, male, 7/8"

35 735141 Phelps Dodge, Type-N, female, 7/8"

36 73402 Phelps Dodge, Splice, 7/8"

37 ST78-75NM Phelps Dodge, Type-N, female, 7/8", 75 ohm

38 ST78-75NF Phelps Dodge, Type-N, female, 7/8", 75 ohm

39 ST78-75S Phelps Dodge, Splice, 7/8", 75 ohm

40 96-500 Prodelin, Type-N, male bulkhead, 1/2"

41 96-875 Prodelin, Type-N, male bulkhead, 7/8"

42 96-1625 Prodelin, Type-N, male bulkhead, 1 5/8"

43 735751 Phelps Dodge, Type-N, female, 1/2"

44 MS-50-PM834 Burndy, 50 pin, male

45 MS-50-RM824 Burndy, 50 pin, female

46 MS-26-PM824 Burndy, 26 pin, male

47 MS-26-RM824 Burndy, 26 pin, female

48 MS-390l2/16-002 Type-BNC plug, RG/U-59

49 31-315 Amphenol, Type-BNC, straight plug, RG/U-17

50 DB-25P TRW/Cinch, Type-"D", 25 pin, male

51 MS-15-PM824 Burndy, 14 pin, male

52 MS-34-PM804 Burndy, 34 pin, male

54 31-2373 Amphenol, Type-TNC

55 220-1N052 Amphenol, 52 pin, female

56 MS-3106E-20-29P Circular, straight plug, 17 pin, male

57 MS-3106E-145-2P Circular, straight plug, 17 pin, male

58 MS-3103-145-9P Circular, straight plug, 17 pin, male

59 MS14RM824 Burndy, 14 pin, female

60 3461-0000 3M, 20 pin, ribbon

61 3415-0000 3M, 50 pin, ribbon

62 MRAC42SJTC6H Winchester, 42 pin, female

63 MRAC14PJTC6H13 Winchester, 14 pin, female

64 MRAC42PJTC6H Winchester, 42 pin, male

65 201355-3 AMP

66 573014-0 AMP

67 573050-0 Amphenol

68 993188-8 Amphenol

69 200271-4 Amphenol

70 200838 Amphenol

71 201358-3 Amphenol

72 201443-2 Amphenol

73 203757-3P Amphenol

74 CA32-2010-10P ITT, Cannon

75 CA32-2010-10S ITT, Cannon

76 CA06RXA20-29S ITT, Cannon

77 CA06RXA280-1P ITT, Cannon

79 CA06RXA28-1S ITT, Cannon

80 CA06RXA28-12S ITT, Cannon

81 CA06RXA28-21 ITT, Cannon

82 MS17804-16-20-1

83 MS17803-16-20-2

84 MS25035-112-3

85 MS3102-22-14S Circular, box receptacle, 19-pin, female

86 MS3102A-14S-6P Circular, box receptacle, 6-pin, male

87 MS3102E-20-27P Circular, box receptacle, 14-pin, male

88 MS3102E-22-14S Circular, box receptacle, 19-pin, female

89 MS3102-16-9P Circular, box receptacle, 4-pin, male

90 MS3102-20-27S Circular, box receptacle, 14-pin, female

91 MS3102R-20-29S Circular, box receptacle, 17-pin, female

92 MS3106E-18-1P Circular, straight plug, 10-pin, male

93 MS3106A-18-1S Circular, straight plug, 10-pin, female

94 MS3106A-18-PC

95 MS3106A-20-29P Circular, straight plug, 17-pin, male

96 MS3106A-20-29S Circular, straight plug, 17-pin, female

97 MS3106E-12S-3P Circular, straight plug, 2-pin, male

98 MS3106E-14S-5S Circular, straight plug, 5-pin, female

99 MS3106E-14S-6P Circular, straight plug, 6-pin, male

100 MS3106E-14S-6S Circular, straight plug, 6-pin, female

101 MS3106E-14S-8P Circular, straight plug, 102 MS3106E-16S-8P Circular, straight plug, 5-pin, male

103 MS3106E-20-7P Circular, straight plug, 8-pin, male

104 MS3106E-20-7S Circular, straight plug, 8-pin, female

105 MS3106E-20-20P Circular, straight plug, 4-pin, male

106 MS3106E-20-27S Circular, straight plug, 14-pin, female

107 MS3106E-20-29P Circular, straight plug, 17-pin, male

108 MS3106E-20-29S Circular, straight plug, 17-pin, female

109 MS3106E-20-35

110 MS3106E-22-14S Circular, straight plug, 19-pin, female

111 MS3106E-22-18S Circular, straight plug, 8-pin, female

112 MS3106E-22-20P Circular, straight plug, 9-pin, male

113 MS3106E-24-28S Circular, straight plug, 24-pin, female

115 MS3106E-24-28P Circular, straight plug, 24-pin, male

116 MS3106E-28-12P Circular, straight plug, 26-pin, male

117 MS3106E-28-12S Circular, straight plug, 26-pin, female

118 MS3106E-28-21S Circular, straight plug, 37-pin, female

119 MS3106E-28-21P Circular, straight plug, 37-pin, male

120 MS3106E-28-10P Circular, straight plug, 7-pin, male

121 MS3106E-26-10S

122 MS3106ER-20-4S Circular, straight plug, 4-pin, female

123 MS3106ER-20-10P

124 MS3106ER-20-11P Circular, straight plug, 13-pin, male

125 MS3106ER-20-11S Circular, straight plug, 13-pin, female

126 MS3106-10SL-4S Circular, straight plug, 2-pin, male

127 MS3108E-14S-5P Circular, angle plug, 5-pin, male

128 MS3108E-20-29P Circular, angle plug, 17-pin, male

129 ST158-50LT Phelps Dodge

130 SE63264P

131 SE602301-6

132 SE66162-3

133 SE83264-0

134 10624 ELCO

135 KS-16690L1

136 L5-20P

137 L5-20R

138 3M34 3M

139 201355-1 Amp, 14 Position

140 202704-1 Amp, 40 Position

141 8016-020-000-709 ELCO, 20 Pin

142 8016-056-000-709 ELCO, 56 Pin

143 8016-056-000-703 ELCO, 56 Pin

144 8016-038-000-709 ELCO, 38 Pin

145 8016-038-000-703 ELCO, 38 Pin

146 8016-020-000-703 ELCO, 20 Pin

147 PL75-9 Twinax Plug

148 202950-1 Amp, 40 Position, Socket

149 UG-154A/U LG Connector for RG-218

150 738355 3" Coax Connector (Cablewave)

151 201298-3 Amp, 14 Position

152 MS3106E28-16P Cannon, Straight Plug, 20 Pin

153 MS3106E28-16S Cannon, Straight Plug, 20 Pin

154 MS3106El6S-5P Cannon, Straight Plug, 3 Pin

155 10-214620-11P Bendix, Straight Plug, 13 Pin

156 10-214-622-14S Bendix, Straight Plug, 19 Pin

157 10-2146l4-7P Bendix, Straight Plug, 3 Pin

158 MS3106A-10SL-35C

159 738802 N Male for Cable FLS 12-50-J

160 738801 N Female for Cable FLS-12-50-J

161 226916-1 N Male for RG214

162 PE4109 BNC Male for RG214

163 PE4212 BNC Female for RG214

164 205209-1 AMP, Connector Receptacle, 37-Socket

165 MS3122El4-l9SW ITT Cannon, Circular, Box MGT. 19-Pin Female, Alternate Position

166 MS3122El8-32SW ITT Cannon, Circular, Box MGT. 32-Pin Female, Alternate Position

167 MS3122El4-l9SX ITT Cannon, Circular, Box MGT. 19-Pin Female, Alternate Position

168 MS3122El4-l9PW ITT Cannon, Circular, Box MGT. 19-Pin Female, Alternate Position

169 MS3122El4-l9PX ITT Cannon, Circular, Box MGT. 19-Pin Female, Alternate Position

170 MS3122El8-32PW ITT Cannon, Circular, Box MGT. 32-Pin Female, Alternate Position

171 DCMA-37P ITT Cannon, 37-Pin, D-Female

172 2648 Thomas & Betts, Cord Grip, Liquidtight, 1" Str.

173 6002 Thomas & Betts, Conduit Fitting, 3/4" Str.

174 MS3122El2-lOS ITT Cannon, Circular, Box MGT. 10-Pin Female

175 41SWT TNC Plug for FSJ1-50

176 3304 Thomas & Betts, 2-Screw Connector 1" Hub

177 3303 Thomas & Betts, 2-Screw Connector 3/4" Hub

178 MS3122El4-l9S ITT Cannon, Circular, Box MGT. 19-Pin, Female

179 MS3122El8-32P ITT Cannon, Circular, Box MGT. 32-Pin, Male

180 AT283-22 ABBOTEC, Nut Plate Connector Shell Size 22

181 AT283-14 ABBOTEC, Nut Plate Connector Shell Size 14

182 MS3122E22-55P ITT Cannon, Circular, Box MGT. 55-Pin, Male

183 609-015 Thomas & Betts, Ribbon Connector

184 609-024 Thomas & Betts, Ribbon Connector

185 DCMA-37S ITT Cannon, 37-Pin, D, Female

186 DBMA-25P ITT Cannon, 25-Pin, D, Male

187 MS3122El8-32S ITT Cannon, Circular, Box MGT. 32-Pin, Female

188 MS3122El4-l2S ITT Cannon, Circular, Box MGT. 8-Pin, #20 Female; 4-Pin, #16 Female

189 MS3122El4-l2SW Same as Above Except Alternate Position

190 3302 Thomas & Betts, 2-Screw Connector Insulated

191 3303 Thomas & Betts, 2-Screw Connector Insulated

192 3304 Thomas & Betts, 2-Screw Connector Insulated

193 2633 Thomas & Betts, Cord-grip, Liquidtight 1/2" Str.

194 2641 Thomas & Betts, Cord-grip, Liquidtight 3/4" Str.

195 6001 Thomas & Betts, Flex Conduit Fitting 1/2" Str.

196 6012 Thomas & Betts, Flex Conduit Fitting 1/2" Elbow

197 MS3122El4-l9P ITT Cannon, Circular, Box MGT. 19-Pin, Male

198 MS3122E22-55S ITT Cannon, Circular, Box MGT. 55-Pin, Female

199 L44N Andrews, Type N

5.0 DOCUMENTATION

5.1 Cable list. The contractor shall fully document all cables supplied as part of the equipment.

The cable list shall give the following information for each cable:

(a) Assigned cable number

(b) Marking applied at one end of cable

(c) Marking applied at other end of cable

(d) Location of both cable ends

(e) Type of connectors at each end

(f) Type of wire or cable employed

(g) Purpose of cable

(h) Cable length in feet

(i) Other pertinent information (i.e., solder/crimp; tooling required)

The required information shall be organized and presented in a logical, preferably tabular, form.

The cable list shall be incorporated into the equipment maintenance and operation manual (NOAA/NESDIS Standard No. S24.801, "Preparation of Operator and Maintenance Manuals").

Sample forms suitable for cable fabrication documentation and system cableing sumation are attached (Attachment 1: "Cable Fabrication Chart," and Attachment 2: "Cable Runs List."

ATTACHMENT #1

"CABLE FABRICATION CHART”

Connector Type Contact Type

Cable Type Cable # _______ Cable Length

Connector Type Contact Type

Contact # PR/Wire # Color Code Contact Number Remarks / Function

ATTACHMENT #2

"CABLE RUNS LIST"TITLE:Page ____ of ____

Cable “W” # Length Type

Connector Type

From To Connector Type

Remarks/Function