1-10307-1- SPEC SHEET - DIGGER DERRICK BODY WITH PLATFORM.pdf

Qty MINIMUM SPECIFICATIONS Check Exception or Variance Additional price (not included in base unit price).

1 60ft Digger Derrick -$

Pole Setting Sheave Height: 59.5 feet -$ Maximum Horizontal Reach from centerline of rotation: 50.3 feet -$ Digging Radius from centerline of rotation. Minimum: 22 feet, Maximum:

35.2 feet -$ Lift Capacity at 10 Ft. Radius: 15,000 lbs. -$ Boom Articulation: -15 to 80 degrees -$ Insulated, 46 KV and below -$ Continuous Rotation: with planetary drive gearbox -$ Side Load Protection -$ Hydraulic Overload Protection (HOP) System -$

EQUIPMENT SPECIFICATION SHEET

Kansas Turnpike Authority

Vendor:

OPERATIONS-ROADSIDE MAINTENANCE

DIGGER DERRICK WITH WORKING PLATFORM

60 Foot Digger Derrick

DEPARTMENT:

EQUIPMENT TITLE:

GENERAL DESCRIPTION: Telephone #/Email:

Possible Models:

Quoted By:

Date:

Possible Models

ATLEC,TEREX, ELLIOTT,VERSALIFT

The specifications listed below are intended to offer the minimum requirements. This is not intended to isolate a particular model. If a specification is not met or not listed, please type all exceptions or variances in the column provided. These will be reviewed to determine which unit best meets KTA needs. Any questions regarding these specifications may be directed to the procurement coordinator listed in the Request for Quote (RFQ) document.

BASE UNIT: MAKE - MODEL

UNIT FEATURES

Load Indicator Gauge: located at the main control panel, displays the percentage -$ of total allowable lifting capacity being utilized. By use of this gauge, the -$ is aware of the hydraulic and structural design rating of the derrick and -$ to the limits during operation. -$ Electronic CAN Controls: -$ Indicator Light Panel at Control Station(s): indicators for hot oil, change -$ oil filter, Rotafloat active (if equipped), and check system light with -$ capabilities -$ Manual override of electronically controlled boom, winch, and digger the main control valve functions at the main control valve. -$

Standard/Low Speed Selector: Operator can select standard or low function -$ speed operation. When in standard mode, each function operates at normal -$ speeds. When in low speed, the maximum operational speed of each -$ slower providing finer feathering capability. The function is separate from -$ throttle control. -$ Remote Control Retrofitable: Control system includes single quick connect plug for quick installation of radio remote control system. -$ Engine Start/Stop and emergency stop at tailshelf -$ for boom, winch, digger and pole guide functions are operated and controlled by elector-proporttional pressure reducing valves which porvides full metering and feathering characteristics -$

Maximum system pressure is 3000 psi. Because flow is provided by a single -$ source (piston pump), maximum flow is available to any combination of -$ including simultaneous operation of the boom and digger/winch functions and flow -$

Hydraulic System: Closed Center hydraulic system with maximum flow of 50 gpm for simultaneous operation of multiple functions. Flow is provided by a variable displacement, pressure compensated, piston pump. This 'flow on demand' system optimizes the overall system efficiency. System is designed with compensators in each valve section for smooth transitions between functions.

Fiberglass hydraulic upper boom and boom tip with provision for platform attachment. -$

Transferable Hydraulic Pole Guides and Steel Boom Flares at the boom tip with adjustable alignment guides. Pole guides are hydraulically powered and proportional for open, close, and tilt which provides superior performance

Pole Guide Tilt Interlock: Prevents the upper boom from extending when the transferrable guides are attached to the intermediate boom until the proximity sensors detect that the guides are tilted all the way up and out of the way. -$

Bearings: All extending booms utilize self lubricating, low friction, slide bearings.

Boom Stow Protection System: A proximity switch on main boom detects the boom support as the boom is being stored and limits the boom down function to avoid excessive down force into the stow -$ Auger Stow Protection: Limits the upward travel of the auger as it reaches the top of the auger stow latch to prevent an overstow condition. -$ Two-part load line attachment point on the intermediate boom -$

Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion

Closed Center hydraulic system with maximum flow of 50 gpm for simultaneous operation of multiple functions -$ Flow is provided by a variable displacement, pressure compensated, piston pump -

FLOW ON DEMAND -$

System is designed with compensators in each valve section for smooth transitions between functions -$ Maximum system pressure is 3000 psi -$ flow is provided by a single source (piston pump), maximum flow is available to any combination of functions including simultaneous operation of the boom and digger/winch functions and flow combining is not necessary. -$ 5 Rear Mount Over Rear Axle-Back of Cab Mount unit -$ Three position throttle integrated into keypad at operator control station. -$ No hard wired upper controls and NO TOOL CIRCUIT at boom tip -$

ELECTRIC-HYDRAULIC CONTROL SYSTEM

Radio Remote Lower Controls (Traditional/Hetronic) -$ Radio Remote Control Layout: CLOCKWISE, push lever to Right rotates boom Clockwise -$ 118 - Docking Station for Radio Remote Control (FA Install) -$ Docking station included in the design of the platform -$ Neck Strap for Radio Remote Contols -$ Combined Use Capacity Chart, Installed on Radio Remote -$ Audible HOP Indicator -$ 8 - Turntable Winch -$ 11 - Normal winch speed (15,000 lbs) -$ 94 - Digger, Two-Speed Mechanical Shift, 12,000 ft-lbs, includes all of the components necessary to operate digger, installed -$

2.50 in Hex Output Shaft With 2.50 in Hex Extension Shaft -$ 86 - Digger - left-hand storage, viewing from boom tip - curbside - opposite from normal. Includes Auger Overstow Protection System -$ Dedicated digger shake command that provides rapid dig/clean reversing function for quick and convenient auger cleaning -$ Anti-Two Block Device that prevents the load block from becoming jammed against the boom tip. Anti-Two Block automatically resets when the condition is resolved and is equipped with a manual override -$ Load Moment Limiter (L.M.L.) that protects against instability by stopping all functions that can cause an overload situation to occur (assuming proper unit setup).

L.M.L. automatically resets when the condition is resolved and is equipped with a manual override. -$ Horn -$ Platform Tubes Installed at Boom Tip -$ Platform tubes are integrated into the steel boomtip. -$ 176 - ANSI use criteria, Platform use or combined Digger Derrick/Platform use -$

Emergency lowering handles at the main control valve-No hard wired control station -$ Electronic Side Load Protection (eSLP) - includes indicator gauge and lamp -$ Electric Over Hydraulic Outrigger Controls -$ Outriggers, Out and Down, Below Frame - with 176 maximum spread (for use behind rear axle) -$

Outriggers, Out and Down, Above Frame - with 176 maximum spread (for use in front of rear axle) - Have capibility to extend outriggers on working side with non working side dropped straight down. -$

Rotational Interlock system for out-and-down outriggers on E-Series derricks. It includes keypads and valving for independent control of beam and down-jack functions. The Rotational Interlock is an automatic safety feature for short-jacking setup -$ Powder coat unit White -$ Custom Pedestal/Tower Color/outrigger housing - WHITE -$ Wylie Anti-Two block system -$

12 Volt Emergency DC Pump, activated at platform, riding seat and at tail shelf -$

110 Volt Duplex with protective cover installed at boom tip in reach of operator. -All wiring to be in cat track. - rigid metalconduit in boom platform -$ 30" Wide X 54" Long X 40" High Aluminum Work platform -$

- Square tube construction -$ Opening door to have safety chain -$

- Platform to have one safety lanyard attachment loop large enough for two lanyards to attach -$ Platform to be rated at 500 lbs. in any position -$ Platform to have 90 Degree hydraulic rotator. To be mounted in a manner that allows platform to be centered on boom tip when fully rotated to front -$ Platform to have hydraulic leveling -$ Platform Rotate & Tilt Functions to be at Radio Controls and at CS turret Control Station -$ Maximum travel height of 13' 5" is required, with platform installed -$ Platform mounted Curbside (CS) of Boom Tip -$ 110 Volt Duplex Receptacle installed at platform in easy reach for operator - All wiring to be in the cat track - Provide pigtail or hook up at slip ring for installation plant to supply power (RIDGID METAL CONDUIT IN PLATFORM) -$

12 Volt Emergency DC Pump, Activated at Platform (via radio), and Tailshelf -$

BOOM PLATFORM

Shall be possible to work overhead (no turret rotation) height with the outriggers set within the truck width. - REQUIRE the Rotation Interlock System -$

Boom Out of Stow Indicator For Lower Boom -$

2 Tool Tray with 9 Pocket Canvas Pouch, 19 Inch x 8 Inch -$

Winch Rope For Turntable Winch 140 Ft Long x 1.13 Inch Dia -$ Load Line Swivel Hook 8-1/2 In Ton -$ D2/3/4000 Series Derrick (Rigid) -$ Subbase Storage With Drop Down Door (Paddle Latch) At Rear Notched for Tool Storage, 8 Inch High To be notched for tamp storage on curbside. -$ 80 Gallon Reservoir, Sight/Temperature Gauge, No Oil Heater -$ Hydraulic Reservoir Accessory Custom Option 1 -$ Hydraulic oil reservoir to be installed at front of flatbed. -$ Hydraulic Oil, HVI-22 with Ultraviolet Dye (Standard) -$

Pump - Right-Hand Rotation 95CC Pressure Compensated (Automatic Transmission -$ Muncie PTO - Electric with rocker switch -$ Hot Shift PTO (for Automatic Transmission) -$

PTO/Transmission Functionality with PTO Auto Neutral for Allison Automatic Transmissions: -Once the PTO switch is on and the transmission is in a near stationary condition (i.e., below 5 mph) the transmission will be forced into neutral. -When the Parking Brake is engaged in addition to the above requirements the PTO will engage. -$ Standard Parking Brake Machine Interlock: Parking (holding) brake must be set before machine is operable. -$ install Tool Circuit For Hose Reel Below Rotation (Male Pressure, Female Return) -$ 50 Ft Non-Conductive Hose Kit, Orange, Includes Quick Disconnects And Dust Caps (Male Pressure, Female Return) (Industry Preferred) -$ Set Of 10 Ft Non-Conductive Hoses And Couplings For Hydraulic Tools-Hoses to be "Red Rubber" -$ Hydraulic Pole Puller -$

UNIT & HYDRAULIC ACCESSORIES

74 - Flow Divider, Optional for Variable Tool Control - for installation of tools at tailself -$ Hydraulic Hose Reel, Spring Loaded, Hannay N616 Series, 50 Ft Hose Capacity (Standard) (Cannot Be Mounted Horizontally) -$ Two-Part Load Line Kit, With Snatch Block And Clevis -$

Flow Divider, Optional for Variable Tool Control - for installation of tools at tailshelf -$

Hydraulic Hose shall be fastened in place with metal reinforced clamps, no plastic ties -$

Hydraulic quick coupler connections shall be mounted on or under the Curbside (CS) front of the bed and at the rear trailer hitch for use with auxiliary tools - Connections at the rear will be used to power auxiliary tools or supply hydraulics to a hydraulically tilting trailer - Note: These hydraulic couplers will be active when the tool reel is active and be controlled by the same on/off valve - Note: Hydraulic flow to be set a 12 GPM using a adjustable flow divider -$

Steel Body -$ Platform - Flatbed -$

Finish Painted Flatbed - non skid paint - see option below to quote alternative -$ Undercoat Body -$ Approximate Flatbed Length (Engineering to Determine Final Length) 268" -$ 3/16'' Treadplate Floor 268" -$ Custom Body Width 98" -$ 4 Inch High Flatbed (No Cross Storage Available) 4" structural channel cross members,

6.25 lbs. per foot on 12" centers -8" structural channel side skirts -8" channel on both ends as well as along each side (smooth side out) -$

Custom Body Cargo Retaining Option Two load binders, 4" wide with nylon straps installed curbside under flatbed. - One (1) installed approximately 12" aft of the top mounted horizontal box. - One (1) installed approximately 60" aft on center from the first binder. - Install a drop-down D-ring across from each binder on the side of the flatbed. - D-ring weldment to be flush with the top of the flatbed. -Provide load binder ratchet lever bar -$ Flatbed shipping channel -$ Light Channels Installed At Rear Of Flatbed -$

BODY

Outrigger Cutout Required -$ Unit Cutout Required -$

Additional Steel Horizontal Storage Box Streetside (SS) Top Mounted Utility Box - Shall be mounted on top of the bed near the front end, located near the outside edge but not extending beyond the edge of the bed. - Box shall be constructed of 18 gauge, minimum, steel with all welded, weatherproof construction - The box shall be approximately 18 inches high, 11 inches deep and 78 inches long with one top door and one side door with two T-Handle Single Point latches with key locks - The top compartment shall contain removable dividers on 4"centers and be approximately 4 inches deep - The side compartment shall be open space. The door shall have retainer chains, or other approved, stop device. The box shall be securely fastened to the bed - Box to be spaced up on plastic spacers for wash out. -$

Additional Steel Horizontal Storage Box Curbside (CS): Top Mounted Utility Box - Shall be mounted on top of the bed near the front end, located near the outside edge but not extending beyond the edge of the bed. - Box shall be constructed of 18 gauge, minimum, steel with all welded, weatherproof construction - The box shall be approximately 18 inches high, 11 inches deep and 78 inches long with one top door and one side door with two T-Handle Single Point latches with key locks

- The top compartment shall contain removable dividers on 4" centers and be approximately 4 inches deep

- The side compartment shall be open space

- The door shall have retainer chains, or other approved, stop device

- The box shall be securely fastened to the bed. Box to be spaced up on plastic spacers for wash out -$

Additional Steel Underbody Storage Box Two (2) Utility Boxes shall be mounted under the front end of the flat bed, one on each side, located near the outside edge but not extending outside the edge of the bed - These two boxes shall be constructed of 14 gauge, minimum galvannealed steel and shall have minimum dimensions of 36inches long, 18 inches deep and 20 inches high with all welded, weatherproof construction - The boxes shall contain a door which hinges at the bottom and has a T Handle Single Point latch with a key lock and retainer chains. - The top of the box shall be constructed of 12 gauge, minimum, steel if it is utilized in mounting the box - Both boxes to have drip edges installed around top and sides to prevent water intrusion - The boxes shall contain a door which hinges at the bottom and has a T-handle type latch with a key lock and a chain, The top of the box shall be constructed of 12 gauge, minimum, steel if it is utilized in mounting the box -$ The lock for all boxes shall be keyed the same. A minimum of two (2) keys shall be furnished. -$

Gator hide finish with grip on body bed floor -$

WARRANTY -$

2 MANUALS - PRINTED FORM -$

1 MANUALS - ELECTRONIC FORM -$

-$ Total Cost Per Unit:

WARRANTY AND MANUALS

Total Additional Costs Per Unit -$

Base Cost Per Unit -$

Option

Date: Final Spec Sheet Approval Signature:

Additional Notes or Comments:

Sheet1