09 Attachment 5 Virkon S MSDS.pdf

Virkon(TM) S

SAFETY DATA SHEET

Product identifier

In case of emergency

Section 1. Identification

Identified uses Disinfectant, Cleaning agents

Material Number : 57818065

EPA Registration Number: :

Supplier/Manufacturer :

39967-137

LANXESS Corporation Product Safety & Regulatory Affairs 111 RIDC Park West Drive Pittsburgh, PA 15275-1112

For Information: US/Canada (800) LANXESS) International: +1 412 809 1000

CHEMTREC (800) 424 9300

International (703) 527 3887 Lanxess Emergency Phone: (866) 673 6350

Section 2. Hazards identification

SKIN IRRITATION - Category 2 SERIOUS EYE DAMAGE - Category 1 SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract irritation) - Category 3

Classification of the substance or mixture

Signal word : Danger

Hazard statements : Causes serious eye damage. Causes skin irritation. May cause respiratory irritation.

Hazard pictograms :

Precautionary statements

Prevention : Wear protective gloves and eye/face protection. Use only in a well-ventilated area.

Avoid breathing dust. Wash hands thoroughly after handling.

Response : Get medical attention if you feel unwell. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. IF ON SKIN: Wash with plenty of soap and water. Take off contaminated clothing. Wash contaminated clothing before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention immediately.

Storage : Store locked up.

Disposal : Dispose of contents and container in accordance with all local, regional, national and international regulations.

HAZCOM Standard Status : This material is considered hazardous by the OSHA Hazard Communication Standard

(29 CFR 1910.1200).

Supplemental label elements

: Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials and food and drink.

Physical state : Powder.

Color : Yellow

Hazard Not Otherwise Classified (HNOC)

: None known.

Virkon(TM) S 1/1357818065 1Version

Section 3. Composition/information on ingredients

Ingredient name CAS number%

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health and hence require reporting in this section.

Substance/mixture :

Occupational exposure limits, if available, are listed in Section 8.

Mixture

Any concentration shown as a range is to protect confidentiality or is due to batch variation.

Pentapotassium bis(peroxymonosulphate) bis(sulphate) 25 - 50 70693-62-8 Sodium Dodecylbenzene Sulfonate 10 - ≤25 25155-30-0 Butanedioic acid, 2-hydroxy- ≤10 6915-15-7 sulphamic acid ≤5 5329-14-6 Potassium hydrogen sulphate ≤5 7646-93-7 Sodium chloride ≤5 7647-14-5 dipotassium peroxodisulphate ≤5 7727-21-1 Dipotassium disulphate ≤5 7790-62-7 dipentene <1 138-86-3

Get medical attention immediately. Wash out mouth with water. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink.

Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Chemical burns must be treated promptly by a physician. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Get medical attention immediately. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. In case of contact with eyes, flush eyes with plenty of water for at least 30 minutes. Chemical burns must be treated promptly by a physician.

In case of contact, flush skin with plenty of water for at least 30 minutes. Get medical attention immediately. Immediately remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Wash clothing before reuse. Clean shoes thoroughly before reuse.

Get medical attention immediately. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. If not breathing, if breathing is irregulor or respiratory arrest occurs, provide artifical respiration, or oxygen by a trained professional, using a pocket type respirator.

Section 4. First aid measures

Eye contact

Skin contact

Inhalation

Ingestion :

Description of first aid measures

Inhalation : May cause respiratory irritation.

May cause burns to mouth, throat and stomach.:Ingestion

Skin contact : Causes skin irritation.

Causes serious eye damage. May cause mechanical irritation (abrasion).:Eye contact

Over-exposure signs/symptoms

Potential acute health effects

Virkon(TM) S 2/1357818065 1Version

Section 4. First aid measures

Protection of first-aiders : If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.

Notes to physician : Treat symptomatically. No specific treatment.

Skin contact

Ingestion

Inhalation May cause respiratory tract irritation with symptoms of coughing, sore throat and runny nose.

Corrosive with symptoms of coughing, burning, ulceration, and pain.

Corrosive with symptoms of reddening, itching, swelling, burning and possible permanent damage.

Causes irritation with symptoms of reddening, itching, and swelling.

Eye contact : Corrosive with symptoms of reddening, tearing, swelling, burning and possible permanent damage.

See toxicological information (Section 11)

Potential chronic health effects

Repeated or prolonged inhalation of dust may lead to chronic respiratory irritation.

Section 5. Fire-fighting measures

Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.

Hazardous thermal decomposition products

Specific hazards arising from the chemical

Decomposition products may include the following materials:

carbon dioxide carbon monoxide nitrogen oxides sulfur oxides phosphorus oxides halogenated compounds metal oxide/oxides

Toxic and irritating gases/fumes may be given off during burning or thermal decomposition. Water runoff from fire fighting may be corrosive.

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Special protective equipment for fire-fighters

Use an extinguishing agent suitable for the surrounding fire. In case of fire, use water spray (fog), foam or dry chemical.

Extinguishing media

Carbon dioxide (CO₂).

Suitable extinguishing media

Unsuitable extinguishing media

Special protective actions for fire-fighters

Section 6. Accidental release measures

Environmental precautions

Personal precautions, protective equipment and emergency procedures

No action shall be taken involving any personal risk or without suitable training.

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Do not breathe dust. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).

Virkon(TM) S 3/1357818065 1Version

Section 6. Accidental release measures Move containers from spill area. Approach release from upwind. Avoid dust generation.

Do not dry sweep. Vacuum dust with equipment fitted with a HEPA filter and place in a closed, labeled waste container. Avoid creating dusty conditions and prevent wind dispersal. Dispose of via a licensed waste disposal contractor. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. Prevent entry into sewers, water courses, basements or confined areas.

Methods and materials for containment and cleaning up

Section 7. Handling and storage

Conditions for safe storage Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. Empty containers retain product residue and can be hazardous. Do not reuse container.

Protective measures Do not get in eyes or on skin or clothing. Do not breathe dust. Do not ingest. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate.

Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. Remove contaminated clothing and protective equipment before entering eating areas. Workers should wash hands and face before eating, drinking and smoking. Put on appropriate personal protection equipment. Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed.

Precautions for safe handling

Pentapotassium bis(peroxymonosulphate) bis(sulphate) None Sodium Dodecylbenzene Sulfonate None Butanedioic acid, 2-hydroxy- None sulphamic acid None Potassium hydrogen sulphate None Sodium chloride None dipotassium peroxodisulphate ACGIH TLV (United States, 3/2016).

TWA: 0.1 mg/m³, (as persulfate) 8 hours.

Dipotassium disulphate None dipentene None

Section 8. Exposure controls/personal protection

Ingredient name Exposure limits

Occupational exposure limits

Appropriate engineering controls

: Use only with adequate ventilation. If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.

Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.

Hygiene measures :

Personal protection

Virkon(TM) S 4/1357818065 1Version

Section 8. Exposure controls/personal protection Although no exposure limit has been established for this product, the OSHA PEL for Particulates Not Otherwise Regulated (PNOR) of 15 mg/m3 - total dust, 5 mg/m3 -respirable fraction is recommended. In addition, the ACGIH recommends 3 mg/m3 -respirable particles and 10 mg/m3 - inhalable particles for Particles (insoluble or poorly soluble) Not Otherwise Specified (PNOS). The following respirator is recommended if airborne concentrations exceed the appropriate standard/guideline. NIOSH approved, air-purifying particulate respirator with N-95 filters.

Respiratory protection :

Skin protection : Wear suitable protective clothing and gloves. Suitable protective footwear.

Eye/face protection : chemical splash goggles and/or face shield. If inhalation hazards exist, a full-face respirator may be required instead. If contact with product is possible, wear safety glasses with side shields.

Medical Surveillance Not available.:

Section 9. Physical and chemical properties Physical state

Melting point

Vapor pressure

Vapor density

Solid. [Powder.]

Not available.

Not available.

Not available.

Pleasant. Sweet.Odor pH

Yellow Color

Evaporation rate Not available.

Auto-ignition temperature

Flash point

Not available.

Not available.

Not available.

2.2 to 2.7 [Conc. (% w/w): 1%]

Viscosity Not available.

Not available.Odor threshold

Partition coefficient: n-octanol/water

Boiling point : Not available.

Decomposition temperature : Not available.

Explosion limits : Not available.

Specific gravity (Relative density)

1.07:

Solubility in water : 65 g/l

Section 10. Stability and reactivity

Hazardous decomposition products

Conditions to avoid Protect from moisture.

Sulfur dioxide, Chlorine

The product is stable.Chemical stability

Strong bases, Combustible material., Acids, Oxidizers, brass, Copper, halogenated compounds, cyanides, heavy metal compounds

Incompatible materials :

Possibility of hazardous reactions

: Under normal conditions of storage and use, hazardous reactions will not occur.

Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Virkon(TM) S 5/1357818065 1Version

Section 11. Toxicological information

Acute toxicity

Irritation/Corrosion

Information on toxicological effects

Information on the likely routes of exposure

Inhalation : May cause respiratory irritation.

May cause burns to mouth, throat and stomach.:Ingestion

Skin contact : Causes skin irritation.

Causes serious eye damage. May cause mechanical irritation (abrasion).:Eye contact

Symptoms related to the physical, chemical and toxicological characteristics

Skin contact

Ingestion

Inhalation May cause respiratory tract irritation with symptoms of coughing, sore throat and runny nose.

Corrosive with symptoms of coughing, burning, ulceration, and pain.

Corrosive with symptoms of reddening, itching, swelling, burning and possible permanent damage.

Causes irritation with symptoms of reddening, itching, and swelling.

Eye contact : Corrosive with symptoms of reddening, tearing, swelling, burning and possible permanent damage.

: Dermal contact. Eye contact. Inhalation. Ingestion.

Potential acute health effects

Potential chronic health effects

Potential immediate effects

: Not available.

Short term exposure

Long term exposure

Potential delayed effects : Not available.

Repeated or prolonged inhalation of dust may lead to chronic respiratory irritation.General :

No known significant effects or critical hazards.Carcinogenicity :

No known significant effects or critical hazards.Mutagenicity :

No known significant effects or critical hazards.Teratogenicity :

Developmental effects : No known significant effects or critical hazards.

Fertility effects : No known significant effects or critical hazards.

Product/ingredient name Result Species Dose Exposure

Virkon(TM) S LD50 Oral Rat - Male, Female

4123 mg/kg - OECD 401 Acute Oral Toxicity

Virkon(TM) S LD50 Dermal Rat - Male, Female

2200 mg/kg Extrapolation according to Regulation (EC) No. 440/2008

Virkon(TM) S LC50 Inhalation Dusts and mists

Rat - Male, Female

3.7 mg/l the particle size measurements of the product indicate that it is not respirable and therefore not bioavailable by the inhalation route.

4 hours -

Test

Virkon(TM) S 6/1357818065 1Version

Mutagenicity

Pentapotassium bis (peroxymonosulphate) bis (sulphate)

OECD 476 In vitro Mammalian Cell Gene Mutation Test

Experiment: In vitro Subject: Mammalian-Animal Cell: Somatic Metabolic activation: +/-

Positive

OECD 473 In vitro Mammalian Chromosomal Aberration Test

Experiment: In vitro Subject: Mammalian-Human Cell: Somatic Metabolic activation: +/-

Positive

OECD 471 Bacterial Reverse Mutation Test

Experiment: In vitro Subject: Bacteria Metabolic activation: +/-

Negative

OECD 474 Mammalian Erythrocyte Micronucleus Test

Experiment: In vivo Subject: Mammalian-Animal

Negative sulphamic acid OECD 471 Bacterial Reverse Mutation Test

Experiment: In vitro Subject: Bacteria Metabolic activation: With and Without

Negative

OECD 471 Bacterial Reverse Mutation Test

Experiment: In vitro Subject: Bacteria Metabolic activation: With and

Negative

Product/ingredient name Test Experiment Result sulphamic acid Eyes - Cornea opacity Rabbit 2 - 4 hours Fully reversible

Eyes - Redness of the conjunctivae

Rabbit 1.5 - 7 days Fully reversible

Eyes - Edema of the conjunctivae

Rabbit 1.5 - 7 days Fully reversible in more than 7 days

Product/ingredient name

Result Score Exposure Observation

Conclusion/Summary

Skin : Irritating to skin. Moderate irritant

Eyes : Risk of serious damage to eyes.

Sensitization

Virkon(TM) S skin Guinea pig Not sensitizing Respiratory Mammal - species unspecified Not sensitizing

Product/ingredient name Route of exposure

Species Result

Skin : Not sensitizing

Respiratory : Not sensitizing

Species

Chronic toxicity

Pentapotassium bis (peroxymonosulphate) bis (sulphate)

Sub-acute NOEL Oral Rat - Male, Female

>1000 mg/kg bw/ day

28 days

Sub-chronic LOAEL Oral Rat - Male, Female

600 mg/kg bw/ day

90 days; 7 days per week daily

Sodium Dodecylbenzene Sulfonate

Chronic NOAEL Oral Rat 220 mg/kg -

Product/ingredient name Result Species Dose Exposure

Conclusion/Summary : Butanedioic acid, 2-hydroxy-:No known significant effects or critical hazards.

Reversibility

Virkon(TM) S 7/1357818065 1Version

Carcinogenicity

Without OECD 476 In vitro Mammalian Cell Gene Mutation Test

Experiment: In vitro Subject: Mammalian-Animal Metabolic activation: With and Without

Negative

OECD 476 In vitro Mammalian Cell Gene Mutation Test

Experiment: In vitro Subject: Mammalian-Animal Metabolic activation: With and Without

Negative

OECD 487 In vitro Micronucleus Test

Experiment: In vitro Subject: Mammalian-Human Metabolic activation: with and without

Negative

Conclusion/Summary : dipotassium peroxodisulphate:Not mutagenic in a standard battery of genetic toxicological tests.

Reproductive toxicity

Conclusion/Summary : Butanedioic acid, 2-hydroxy-:No known significant effects or critical hazards.

Specific target organ toxicity (single exposure)

Pentapotassium bis(peroxymonosulphate) bis(sulphate) Category 3 Not applicable. Respiratory tract irritation

Butanedioic acid, 2-hydroxy- Category 3 Not applicable. Respiratory tract irritation sulphamic acid Category 3 Not applicable. Respiratory tract irritation

Potassium hydrogen sulphate Category 3 Not applicable. Respiratory tract irritation

Sodium chloride Category 3 Not applicable. Respiratory tract irritation dipotassium peroxodisulphate Category 3 Not applicable. Respiratory tract irritation

Name Category

Not available.

Route ATE value (Acute Toxicity Estimates)

Acute toxicity estimates

Route of exposure

Target organs

Product/ingredient name IARC NTP OSHACAS #

Pentapotassium bis (peroxymonosulphate) bis(sulphate)

70693-62-8 Not classified. Not classified. Not classified.

Sodium Dodecylbenzene Sulfonate 25155-30-0 Not classified. Not classified. None Butanedioic acid, 2-hydroxy- 6915-15-7 Not classified. Not classified. Not classified.

sulphamic acid 5329-14-6 Not classified. Not classified. Not classified.

Potassium hydrogen sulphate 7646-93-7 Not classified. Not classified. Not classified.

Sodium chloride 7647-14-5 Not classified. Not classified. Not classified.

dipotassium peroxodisulphate 7727-21-1 Not classified. Not classified. Not classified.

Dipotassium disulphate 7790-62-7 Not classified. Not classified. Not classified.

dipentene 138-86-3 Not classified. Not classified. Not classified.

Virkon(TM) S 8/1357818065 1Version

Section 12. Ecological information Toxicity

Product/ingredient name SpeciesResult Exposure

Pentapotassium bis (peroxymonosulphate) bis (sulphate)

OECD 201 Alga, Growth Inhibition Test

Acute EC50 >1 mg/l Fresh water Algae - Pseudokirchneriella subcapitata

72 hours

OECD 202 Daphnia

sp. Acute Immobilization Test

Acute EC50 3.5 mg/l Fresh water

Daphnia - Daphnia magna

48 hours

OECD 203 Fish, Acute Toxicity Test

Acute LC50 53 mg/l Fresh water Fish - Oncorhynchus mykiss

96 hours

OECD 201 Alga, Growth Inhibition Test

Chronic NOEC 0.5 mg/l Fresh water

Algae - Pseudokirchneriella subcapitata

72 hours

Sodium Dodecylbenzene Sulfonate

- Chronic NOEC 4 mg/l Daphnia - Daphnia magna

7 days

- Chronic NOEC 3.1 mg/l Fish - Oncorhynchus kisutch

3 days

Butanedioic acid, 2-hydroxy- OECD 201 Alga, Growth Inhibition Test

Acute EC50 >100 mg/l Fresh water

Algae - Daphnia magna

72 hours

OECD 202 Daphnia

sp. Acute Immobilization Test

Acute EC50 240 mg/l Fresh water

Daphnia - Daphnia magna

48 hours

OECD 203 Fish, Acute Toxicity Test

Acute LC50 >100 mg/l Fresh water

Fish - Danio rerio 96 hours

OECD 201 Alga, Growth Inhibition Test

Chronic NOEC 100 mg/l Fresh water

Algae - Daphnia magna

72 hours sulphamic acid OECD 201 Alga, Growth Inhibition Test

Acute EC50 48 mg/l Fresh water Algae - Desmodesmus subspicatus

72 hours

OECD 202 Daphnia

sp. Acute Immobilization Test

Acute EC50 71.6 mg/l Fresh water

Daphnia - Daphnia magna

48 hours

OECD 209 Activated Sludge, Respiration Inhibition Test

Acute EC50 >200 mg/l Fresh water

Micro-organism 3 hours

OECD 203 Fish, Acute Toxicity Test

Acute LC50 70.3 mg/l Fresh water

Fish - Pimephales promelas

96 hours

OECD 201 Alga, Growth Inhibition Test

Chronic EC10 29.5 mg/l Fresh water

Algae - Desmodesmus subspicatus

72 hours

OECD 201 Alga, Growth Inhibition Test

Chronic NOEC 18 mg/l Fresh water

Algae - Desmodesmus subspicatus

72 hours

Sodium chloride - Acute EC50 402.6 mg/l Daphnia 48 hours

- Acute LC50 7400 mg/l Fish 96 hours dipotassium peroxodisulphate

OECD 201 Alga, Growth Inhibition Test

Acute EC50 83.7 mg/l Algae - Pseudokirchneriella subcapitata

72 hours

- Acute EC50 120 mg/l Daphnia - Daphnia magna

48 hours

- Acute LC50 76.3 mg/l Fish - Oncorhynchus mykiss

96 hours

Dipotassium disulphate - Acute EC10 656 mg/l Read-across from CAS # 7778-80-5 Fresh water

Algae - Pseudokirchneriella subcapitata

96 hours

Test

Virkon(TM) S 9/1357818065 1Version

Section 12. Ecological information

LogPow BCF Potential

Bioaccumulative potential

: No known significant effects or critical hazards.

Product/ingredient name

Pentapotassium bis (peroxymonosulphate) bis (sulphate)

<0.3 - low

Sodium Dodecylbenzene Sulfonate

0.45 220 low

Butanedioic acid, 2-hydroxy- -1.26 - low

Product/ingredient name Aquatic half-life Photolysis Biodegradability

Butanedioic acid, 2-hydroxy- - - Readily Sodium chloride - - Readily dipentene - - Not readily

Conclusion/Summary : Not available.

Persistence and degradability

Butanedioic acid, 2-hydroxy- OECD 301B Ready Biodegradability - CO₂ Evolution Test

67.5 % - Readily - 28 days - -

Product/ingredient name Test DoseResult Inoculum

Conclusion/Summary : Not available.

Soil/water partition coefficient (KOC)

: Not available.

Mobility in soil

Other adverse effects

- Acute EC50 1492 mg/l Read-across from CAS # 7778-80-5 Fresh water

Algae - Pseudokirchneriella subcapitata

96 hours

- Acute EC50 720 mg/l Read-across from CAS # 7778-80-5 Fresh water

Daphnia - Daphnia magna

48 hours

- Acute LC50 680 mg/l Read-across from CAS # 7778-80-5 Fresh water

Fish - Pimephales promelas

96 hours

- Chronic NOEC 790 mg/l Read-across from CAS # 7757-82-6 Fresh water

Daphnia - Daphnia dubia (water flea)

7 days

- Chronic NOEC >595 mg/l Read-across from CAS # 7757-82-6 Fresh water

Fish - Pimephales promelas

7 days dipentene - Acute EC50 0.421 mg/l Fresh water

Daphnia - Daphnia magna

48 hours

- Acute LC50 0.702 mg/l Fresh water

Fish - Pimephales promelas

96 hours

Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Waste disposal should be in accordance with existing federal state, provincial and or local environmental controls laws.

:Disposal methods

Virkon(TM) S 10/1357818065 1Version

Section 13. Disposal considerations RCRA classification : : If discarded in its purchased form, this product would not be a hazardous waste either by listing or by characteristic. However, under RCRA, it is the responsibility of the product user to determine at the time of disposal, whether a material containing the product or derived from the product should be classified as a hazardous waste. (40

CFR 261.20-24)

Section 14. Transport information

9 8, 146, 335, A112, B54, B120, IB8, IP3,

N20, N91, T1, TP33

When in individual containers of less than the Product RQ, this material ships as non-regulated.

DOT Classification Environmentally hazardous substance, solid, n.o.s. (SODIUM

DODECYLBENZENE

SULFONATE)

III

IMDG Class

IATA-DGR Class

Regulatory information

UN number Proper shipping name

Classes PG* Label Additional information

UN3077

PG* : Packing group

7310 lbsRQ :

-- Not regulated.

Not regulated.

Section 15. Regulatory information

State regulations The following chemicals are specifically listed by individual states; other product specific health and safety data in other sections on the SDS may also be applicable for state requirements. For details on your regulatory requirements you should contact the appropraite agency in your state.

Sodium Metaphosphate 10124-56-8 MA - S, PA - RTK HS 10 - ≤25 Sodium Dodecylbenzene Sulfonate 25155-30-0 MA - S, NJ - HS, PA - RTK HS 10 - ≤25 dipotassium peroxodisulphate 7727-21-1 MA - S, NJ - HS, PA - RTK HS ≤5 sulphamic acid 5329-14-6 NJ - HS ≤5 Potassium hydrogen sulphate 7646-93-7 NJ - HS ≤5 Pentapotassium bis (peroxymonosulphate) bis(sulphate)

70693-62-8 25 - 50

Butanedioic acid, 2-hydroxy- 6915-15-7 ≤10

Ingredient name CAS number State Code Concentration

SARA Title III Section 313 Toxic Chemicals

SARA 311/312 :

SARA Title III Section 302 Extremely Hazardous Substances

Immediate (acute) health hazard

US EPA CERCLA

Hazardous Subtances (40

CFR 302.4)

CAS numberIngredient name RQ

Sodium Metaphosphate 10124-56-8 5000 lbs. (2270 kg)

Sodium Dodecylbenzene Sulfonate 25155-30-0 1000 lbs. (454 kg)

None

None

Virkon(TM) S 11/1357818065 1Version

Section 15. Regulatory information

U.S. Toxic Substances Control Act

: This product is excluded from TSCA Regulation under FIFRA Section 3 (2)(B)(ii) when used as a pesticide.

WARNING: This product contains a chemical known to the State of California to cause cancer.

California Prop. 65

Ingredient name Cancer ReproductiveCAS # Concentration (%)

7-methyl-3-methyleneocta-1, 6-diene

123-35-3 ≤0.1 Yes

Massachusetts Substances: MA - S Massachusetts Extraordinary Hazardous Substances: MA - Extra HS New Jersey Hazardous Substances: NJ - HS Pennsylvania RTK Hazardous Substances: PA - RTK HS Pennsylvania Special Hazardous Substances: PA - Special HS

FIFRA

This chemical is a pesticide product registered by the United States Environmental Protection Agency and is subject to certain labeling requirements under federal pesticide law. These requirements differ from the classification criteria and hazard information required for safety data sheets (SDS), and for workplace labels of non-pesticide chemicals. The hazard information required on the pesticide label is reproduced below. The pesticide label also includes other important information, including directions for use.

Signal word : DANGER

Hazard statements : Danger. Powder is corrosive. Causes irreversible eye damage and skin burns. Harmful if swallowed or absorbed through skin. Corrosive statement does not refer to 1% in-use solution.

FIFRA Registered Composition:

Active Ingredients:

Potassium peroxymonosulfate (CAS# 10058-23-8) 21.41% Sodium chloride (CAS# 7647-14-5) 1.5% Other Ingredients 77.09% Total: 100%

39967-137EPA Registration Number :

Section 16. Other information Hazardous Material Information System

National Fire Protection Association (U.S.A.)

The customer is responsible for determining the PPE code for this material. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may be purchased exclusively from J. J. Keller (800) 327-6868.

0= Minimal 1=Slight 2=Moderate 3=Serious 4=Severe

0=Insignificant 1=Slight 2=Moderate 3=High 4=Extreme *=Chronic

No.

3Health

Special

Instability/Reactivity

Flammability

Health

Flammability

Physical hazards

Virkon(TM) S 12/1357818065 1Version

Section 16. Other information

Notice to reader

Date of issue

Date of previous issue

Version :

Our method of hazard communication is comprised of Product Labels and Safety Data Sheets. HMIS and NFPA ratings are provided as a customer service.

Indicates information that has changed from previously issued version.

08-14-2017

No previous validation

This information is furnished without warranty, express or implied. This information is believed to be accurate to the best knowledge of LANXESS Corporation. The information in this SDS relates only to the specific material designated herein. LANXESS Corporation assumes no legal responsibility for use of or reliance upon the information in this SDS.

No.

No.

Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright ©1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.

Product Safety and Regulatory Affairs