02 Attachment I- Fire Truck Specifications.pdf

Technical Specifications: High-Mobility Firefighting Water Tanker (2 Units)

Technical Specifications for High-Mobility Firefighting Water Tanker

Section 1: General Requirement and Reference Model

1.1. Requirement: The requirement is for the procurement of two (2) High-Mobility Firefighting Water Tankers as a humanitarian assistance project for the Emergency Management Service (EMS) of Georgia. The vehicles must meet or exceed all mandatory requirements outlined in this document.

1.2. Reference for Illustrative Purposes Only: The images below are provided as a visual reference to illustrate the general configuration and type of vehicle required. These images do not represent a required brand or model. All proposals will be evaluated for acceptability based on the o eror's ability to meet or exceed the mandatory salient characteristics detailed in the sections below. Any proposed "or equal" product must meet all listed salient characteristics to be considered technically acceptable.

Figure 1: Illustrative example of a High-Mobility Firefighting Water Tanker

Figure 2: Illustrative example showing general equipment layout and chassis type

Section 2: Salient Characteristics (Mandatory Minimum Requirements)

2.1. Chassis and Drivetrain

Specification Requirement

Wheel Configuration

4×4 with single tires on both front and rear axles.

Transmission Manual Transmission.

Engine Type Diesel engine with an auxiliary starting system for low-temperature operation.

Emission Level Not to exceed Euro 3 (EURO 3).

Engine Power Not less than 270 hp.

Fuel Tank Capacity Not less than 150 Liters.

Permissible Gross Weight

Not less than 15,000 kg.

Driven Axles All-wheel drive (4×4) with lockable front, rear, and inter-axle di erentials (100% locking).

Suspension System Designed for rough terrain, equipped with lateral stability stabilizers and shock absorbers.

Braking System Anti-lock Braking System (ABS) and EBS (or equivalent), parking brake, and engine brake.

Chassis Frame Must be manufactured and coated with special anti-corrosion protection.

Tires O -road tread pattern. The vehicle must include one full-size spare tire mounted on the vehicle, supplied with a tire lifting/lowering winch.

2.2. Vehicle Dimensions and O -Road Capability

Specification Requirement

Length (without winch) Not exceeding 7000 mm.

Width (excluding mirrors) Not exceeding 2500 mm.

Height Not exceeding 3350 mm.

Approach Angle Not less than 35 degrees.

Fording Depth Not less than 860 mm.

Ground Clearance Not less than 35 cm.

2.3. Cab and Crew Compartment

• Configuration: Four-door, single-module cab with no partition wall between the front and rear compartments.

• Seating Capacity: 6 total (1 driver + 1 commander in front, 4 crew in rear), all oriented in the direction of travel. Seats must be made of wear-resistant, easy-to-clean material and equipped with seat belts and headrests.

• Compliance: The cab must comply with EN 1846-2 and hold ECE R29 certification for occupant safety.

• Features:

• Heating and air-conditioning systems.

• Electric window lifters for driver and commander doors.

• Protection:

• The cab shall be externally protected by a metal protective frame (roll-over protection structure).

• Windshield, side windows, and lighting units must be fitted with removable metal protective grilles (mesh size 6 × 6 cm). The windshield grille must be a two-piece, individually openable design.

• Interior Equipment:

• Cab lighting su icient for map reading.

• Microphone and control panel for the loudspeaker/siren.

• Control panel for flashing warning signal devices.

2.4. Apparatus Body

• Water Tank

• Capacity: Not less than 4,000 liters.

• Material: AISI 316 stainless steel (to be confirmed by a manufacturer’s certificate of conformity).

• Design: Must include internal ba le partitions, monitoring indicators, a water spill prevention system, and an easily openable inspection hatch on the roof.

• Filling: Possible via the pump compartment and the roof-mounted hatch.

• Foam Tank

• Capacity: Not less than 120 liters.

• Material: Stainless steel.

• System: Equipped with a foam proportioning (dosing) system capable of operating medium-expansion foam generators (200 L/min and 400 L/min).

2.5. Pump and Pumping System

• Type: Two-stage (normal and high-pressure) pump installed at the rear of the vehicle.

• Compliance: Must comply with the requirements of EN 1028.

• Performance:

• Normal-Pressure: Not less than 2,000 L/min at 10 bar.

• High-Pressure: Not less than 240 L/min at 40 bar.

• Water Suction Height: Not less than 7.5 meters.

• Outlets: Equipped with four water discharge outlets with European-type Storz couplings.

• Pump Compartment: Must contain, at a minimum:

• Gauges: Mano-vacuummeter, low-pressure gauge, high-pressure gauge.

• Indicators: Visual water level indicator, electrical foam level indicator, pump shaft rotation speed indicator.

• Controls: Engine speed controller, engine stop switch, lighting switch, and clear schematic plates for all functions.

• Pump operating hours counter.

2.6. Equipment and Storage

• Hose Reels: Two reels in the pump compartment, each equipped with a shut-o valve and not less than 50 meters of 25 mm hose rated for at least 40 bar operating pressure.

• Winch: Minimum pulling capacity of 5,000 kg, fitted with a 25 m steel cable.

• Lighting Tower: Telescopic, remotely controllable mast with a minimum of four (4) floodlights providing 360-degree coverage.

• Compartments:

• At least two appropriately sized compartments on each side for equipment storage.

• Dedicated storage for four (4) rigid suction handles (2m length each).

• Compartments must have aluminum partitions, common key locks, and automatic LED lighting.

• Standard Equipment Supplied:

• Jack (min. 10-ton capacity)

• Tire inflation hose (min. 10m) with pressure gauge

• Wheel wrench set

• First aid kit

• Fire extinguisher

• Additional Required Equipment:

• Monitor (deck gun) - Country of origin, Manufacturer, and Model to be specified.

• Breathing apparatus mounting brackets inside the cab.

• Rear-view video camera.

• System for manual increase/decrease of pump rotational speed, controllable from the pump compartment.

2.7. General and Operating Conditions

• Operating Temperature: All mechanisms and systems must operate reliably in ambient temperatures from -10°C to +50°C.

• Ergonomics: All handles, boxes, and controls must be operable while wearing gloves.

• Surfaces: All working surfaces and platforms shall be made of anti-slip material.

• Exterior Marking: The exterior shall be marked with logos, textual markings, and reflective elements in accordance with the Purchaser's designs.

• Exterior Protection: Glass covers of all lighting units must be protected by metal grilles.

• Cooling System: The vehicle shall be equipped with a water sprinkler system for cooling the cab and tires during firefighting operations, controlled from inside the cab.