Tow Haulage Controls

Contractor shall furnish and deliver the following equipment (or approved equal) as listed below:
1. Two (2) variable frequency drives, 3 phase, 380-480VAC, 60Hz, 20HP, IP20/NEMA Type 1 enclosure, humidity-and dust resistant, Yaskawa Cat. # CIMR-A-U4A0031FMA. Two (2) encoder cards, Yaskawa Cat. # PG-X2.

2. Two (2) general purpose severe duty, IEEE 841 NEMA Premium Energy Efficient motors, 15HP, 3 phase, TEFC, foot mount, 60Hz, 460VAC, 1800RPM, 254T NEMA Frame, 1.25 SF, 92.4% efficiency minimum, WEG Cat. # 01518ST3QIE254T-W22. Each motor shall be provided with a Dynapar Model. # HS35R1024H3P7 encoder pre-installed on the back of the motor by the motor's manufacturer. Contractor shall provide five (5) Dynapar Model. # HS35R1024H3P7 encoder for spare. Two (2) 100' of 10 pin MS, Cable assemblies for use with differential line driver with index outputs, Dynapar Cat. # 1400635-0100.

3. Two (2) 500VA, single phase, energy efficient type, 120-480V, 60Hz, control transformer with primary and secondary fuse blocks pre-installed, Square D Cat. # 9070TF500D1. Ten (10) 480VAC, 2A, fuses and ten (10) 120VAC, 10A, fuses which are compatible with the pre-installed fuse blocks.

4. Two (2) 50A, 480VAC, 35kAIC @ 480VAC, 3P, adjustable thermal and fixed magnetic trip circuit breaker, Eaton Cat. # EGS3050AFG. Two (2) handle mechanism kits, NEMA 4X, for EG frame breaker (includes 12" shaft, mechanism, and handle), Eaton Cat. # EGHMVD12RX/68C6040G23.

5. Ten (10) control relays, 4 NO contacts with 120V, 60Hz coil, Eaton Cat. #D15CR40AB. Din rail, 35mm, 1m length, Eaton Cat. # MC382MA1.

6. Five (5) 10 position rotary selector switch, Allied Electronic Cat. # 948-7285. Five (5) knob, ¼" shaft, 1- ½", Allied Electronic Cat. # 296-6285.

7. Five (5) 3 position selector switch, Eaton Cat. # 10250T20KB.

8. Five (5) momentary red push buttons with contact blocks, Eaton Cat. # 10250T102-53.

9. Five (5) indicator light, green, 120VAC, Eaton Cat. # 10250T197LGP2A.

10. One (1) 24" x 24" x 12" continuous hinge, single door, with 3 point locking, type 4X stainless steel enclosure, Eaton B-Line series Cat. # 242412-4XS3PT. One (1) back panel, Eaton B-Line series Cat. # AW2424P.

11. One (1) 12" x 12" x 6" premier series with quarter turn latch, type 4X stainless steel enclosure, Eaton B-Line series Cat. # 12126-SDSS4. One (1) back panel, Eaton B-Line series Cat. # 1212P. One (1) swing out panel, Eaton B-Line series Cat. # 1212SP. One (1) panel handle, Eaton B-Line series Cat. # WMHNL.

12. One (1) 16" x 16" x 8" premier series with quarter turn latch, type 4X stainless steel enclosure, Eaton B-Line series Cat. # 16168-SDSS4. One (1) back panel, Eaton B-Line series Cat. # 1616P. One (1) swing out panel, Eaton B-Line series Cat. # 1616SP. One (1) panel handle, Eaton B-Line series Cat. # WMHNL.

13. Ten (10) double row terminal blocks, 12 poles, 30A, 600V, Cooper Bussmann Cat. # TB300-12. Ten (10) double row terminal blocks, 6 poles, 30A, 600V, Cooper Bussmann Cat. # TB300-6.a

BRAND NAME OR EQUAL.
To be considered equal, alternate equipment proposed shall meet the salient features provided herein. The Contractor shall submit catalog cut / documentation with their price quote. If an alternate is proposed, the Government shall make the comparison to verify that it is equal to the model number specified and that it can meet the salient features. Information provided in the catalog cut documents shall be complete and of the level of detail to allow the Government to make the comparison. The Contractor shall not purchase and deliver equipment prior to the Government's approval.

PERIOD OF PERFORMANCE.
The equipment in this contract shall be delivered within 60 calendar days of contract award.

SECURITY.

All contractors and all associated sub-contractors shall comply with applicable District and local security policies and procedures (provided by the Government representative). The contractor shall provide any/all requested information required for background checks, background investigations and/or to meet installation/facility access requirements to be accomplished by the District Security Office. Contractor workforce must comply with all personal identity verification requirements as directed by DOD, HQDA and/or local policy. In addition to the changes otherwise authorized by the changes clause of this contract, should the Force Protection Condition (FPCON) at any installation or facility change, the Government may require changes in contractor security matters or processes.

Background Investigation Requirements: Since this is a supply contract, there are no background investigation requirements. However, the Contractor(s) will be escorted at all times inside any restricted area. Contact the Point of Contact provided below for determination of the areas that are considered to be restricted.

SHIPMENT.
The equipment shall be packed in a manner acceptable to preserve the condition of the equipment as it left the Contractor's shop. The packaging shall clearly identify the contents and weight of the package. All transportation, delivery, and storage costs shall be included in the bid price.
Equipment shall be adequately protected from damage during shipping and handling. All damage shall be replaced by the Contractor with no additional cost to the Government.
Contractor shall notice the point of contact person one week prior to delivery date. Delivery will be made from Monday to Thursday, 0800 to 1600 local time, except Federal holidays to the following address:

.

SCOPE OF WORK
FOR
PICKWICK MAIN LOCK
DOWNSTREAM GUIDEWALL TOW HAULAGE CONTROLS REHAB

SCOPE.
Contractor shall furnish and deliver the following equipment (or approved equal) as listed below:
1. Two (2) variable frequency drives, 3 phase, 380-480VAC, 60Hz, 20HP, IP20/NEMA Type 1 enclosure, humidity-and dust resistant, Yaskawa Cat. # CIMR-A-U4A0031FMA. Two (2) encoder cards, Yaskawa Cat. # PG-X2.

2. Two (2) general purpose severe duty, IEEE 841 NEMA Premium Energy Efficient motors, 15HP, 3 phase, TEFC, foot mount, 60Hz, 460VAC, 1800RPM, 254T NEMA Frame, 1.25 SF, 92.4% efficiency minimum, WEG Cat. # 01518ST3QIE254T-W22. Each motor shall be provided with a Dynapar Model. # HS35R1024H3P7 encoder pre-installed on the back of the motor by the motor's manufacturer. Contractor shall provide five (5) Dynapar Model. # HS35R1024H3P7 encoder for spare. Two (2) 100' of 10 pin MS, Cable assemblies for use with differential line driver with index outputs, Dynapar Cat. # 1400635-0100.

3. Two (2) 500VA, single phase, energy efficient type, 120-480V, 60Hz, control transformer with primary and secondary fuse blocks pre-installed, Square D Cat. # 9070TF500D1. Ten (10) 480VAC, 2A, fuses and ten (10) 120VAC, 10A, fuses which are compatible with the pre-installed fuse blocks.

4. Two (2) 50A, 480VAC, 35kAIC @ 480VAC, 3P, adjustable thermal and fixed magnetic trip circuit breaker, Eaton Cat. # EGS3050AFG. Two (2) handle mechanism kits, NEMA 4X, for EG frame breaker (includes 12" shaft, mechanism, and handle), Eaton Cat. # EGHMVD12RX/68C6040G23.

5. Ten (10) control relays, 4 NO contacts with 120V, 60Hz coil, Eaton Cat. #D15CR40AB. Din rail, 35mm, 1m length, Eaton Cat. # MC382MA1.

6. Five (5) 10 position rotary selector switch, Allied Electronic Cat. # 948-7285. Five (5) knob, ¼" shaft, 1- ½", Allied Electronic Cat. # 296-6285.

7. Five (5) 3 position selector switch, Eaton Cat. # 10250T20KB.

8. Five (5) momentary red push buttons with contact blocks, Eaton Cat. # 10250T102-53.

9. Five (5) indicator light, green, 120VAC, Eaton Cat. # 10250T197LGP2A.

10. One (1) 24" x 24" x 12" continuous hinge, single door, with 3 point locking, type 4X stainless steel enclosure, Eaton B-Line series Cat. # 242412-4XS3PT. One (1) back panel, Eaton B-Line series Cat. # AW2424P.

11. One (1) 12" x 12" x 6" premier series with quarter turn latch, type 4X stainless steel enclosure, Eaton B-Line series Cat. # 12126-SDSS4. One (1) back panel, Eaton B-Line series Cat. # 1212P. One (1) swing out panel, Eaton B-Line series Cat. # 1212SP. One (1) panel handle, Eaton B-Line series Cat. # WMHNL.

12. One (1) 16" x 16" x 8" premier series with quarter turn latch, type 4X stainless steel enclosure, Eaton B-Line series Cat. # 16168-SDSS4. One (1) back panel, Eaton B-Line series Cat. # 1616P. One (1) swing out panel, Eaton B-Line series Cat. # 1616SP. One (1) panel handle, Eaton B-Line series Cat. # WMHNL.

13. Ten (10) double row terminal blocks, 12 poles, 30A, 600V, Cooper Bussmann Cat. # TB300-12. Ten (10) double row terminal blocks, 6 poles, 30A, 600V, Cooper Bussmann Cat. # TB300-6.a

BRAND NAME OR EQUAL.
To be considered equal, alternate equipment proposed shall meet the salient features provided herein. The Contractor shall submit catalog cut / documentation with their price quote. If an alternate is proposed, the Government shall make the comparison to verify that it is equal to the model number specified and that it can meet the salient features. Information provided in the catalog cut documents shall be complete and of the level of detail to allow the Government to make the comparison. The Contractor shall not purchase and deliver equipment prior to the Government's approval.

PERIOD OF PERFORMANCE.
The equipment in this contract shall be delivered within 60 calendar days of contract award.

SECURITY.

All contractors and all associated sub-contractors shall comply with applicable District and local security policies and procedures (provided by the Government representative). The contractor shall provide any/all requested information required for background checks, background investigations and/or to meet installation/facility access requirements to be accomplished by the District Security Office. Contractor workforce must comply with all personal identity verification requirements as directed by DOD, HQDA and/or local policy. In addition to the changes otherwise authorized by the changes clause of this contract, should the Force Protection Condition (FPCON) at any installation or facility change, the Government may require changes in contractor security matters or processes.

Background Investigation Requirements: Since this is a supply contract, there are no background investigation requirements. However, the Contractor(s) will be escorted at all times inside any restricted area. Contact the Point of Contact provided below for determination of the areas that are considered to be restricted.

SHIPMENT.
The equipment shall be packed in a manner acceptable to preserve the condition of the equipment as it left the Contractor's shop. The packaging shall clearly identify the contents and weight of the package. All transportation, delivery, and storage costs shall be included in the bid price.
Equipment shall be adequately protected from damage during shipping and handling. All damage shall be replaced by the Contractor with no additional cost to the Government.
Contractor shall notice the point of contact person one week prior to delivery date. Delivery will be made from Monday to Thursday, 0800 to 1600 local time, except Federal holidays to the following address:

1188 Cinder Road
Old Hickory, TN 37138
Phone: 615-240-4037
Mobile: 615-417-4842
Email: Harold.A.Deskins@usace.army.mil

Primary Point of Contact: Brian Brewer, 731-925-2334, brian.d.brewer@usace.army.mil
Alternate Point of Contact: Harold Deskins, 615-417-4842, harold.a.deskins@usace.army.mil

.