NRP, cooling interf - and similar replacement parts
Closed Solicitation Posted
This opportunity was awarded. See the award notice from .
- Solicitation number
- N0038325QC452
- Agency
-
Naval Supply Systems Command
Department of the Navy, Department of Defense
- Responses due
- Set-aside
- No set-aside
Opportunity facts
- NAICS code
- 336413 Other Aircraft Parts and Auxiliary Equipment Manufacturing
- Points of contact
Notice details come from SAM.gov. Updated .
About this opportunity
This is a sole source spares solicitation issued by the Department of the Navy Naval Supply Systems Command for the procurement of three replacement parts for cooling interfaces and similar components used in critical shipboard systems. The delivery order will be awarded against existing Blanket Order Agreement (BOA) N00383-23-G-SX01, with all terms and conditions of the BOA taking precedence over conflicting terms in the solicitation. The procurement falls under NAICS code 336413 (Other Aircraft Parts and Auxiliary Equipment Manufacturing) and PSC code 1680 (Miscellaneous Aircraft Accessories and Components). Contractors must comply with MIL-STD-130 marking standards and meet Buy American requirements along with other compliance obligations outlined in the representations and certifications clauses. The current proposal due date is December 19, 2025, which has been extended multiple times throughout the solicitation process since the initial posting on April 29, 2025. The solicitation includes provisions for priority rating under the National Defense, Emergency Preparedness, and Energy Program designation.
The solicitation carries no set-aside designation and is designated for sole source procurement, indicating a single qualified contractor has been identified for this requirement. Specific award value and quantity details are not fully detailed in the available documentation, with several fields marked as "TBD" (to be determined). Payment instructions will be processed through the Wide Area Workflow system using invoice and receiving report combinations, with the CAGE code N00383 designated for this procurement. The primary point of contact for the solicitation is Michael J. Dickens at the Naval Supply Systems Command, reachable at 771-229-0418 or michael.j.dickens5.civ@us.navy.mil. While the place of performance is not explicitly stated, the parts' use in shipboard systems suggests delivery requirements to naval facilities, with performance timeline and delivery schedules to be governed by the terms of the underlying BOA.
Notice text
6 versions
Update #6 · Latest ·
CONTACT INFORMATION|4|N792.12|T1F|771-229-0418|michael.j.dickens5.civ@us.navy.mil|
ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19||||||||||||||||||||
WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (Combo)||TBD|N00383|TBD|TBD|TBD |TBD|||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1||
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11||||||||||||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13||||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5||||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1||
ROYALTY INFORMATION (APR 1984)|1||
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336413|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1||
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
Solicitation is extended to 19 December 2025.
\
The purpose of this amendment is to incorporate the following change:
1. The proposal submission date is extended to 31 October 2025.
2. All other terms and conditions remain unchanged.
\
This amendment is being issued to incorporate the following change:
1. The proposal submission date is extended to 25 September 2025.
2. All other terms and conditions remain unchanged.
\
The purpose of this amendment is to issue the following change:
1. The proposal due date is extended to 22 August 2025.
2. All other terms and conditions remain unchanged.
\
The purpose of this amendment is to incorporate the following change:
1. The solicitation date is extended to 9 July 2025.
2. All other terms and conditions remain unchanged.
\
This is a sole source spares solicitation for the procurement of three items.
The pursuant delivery order will be awarded against BOA N00383-23-G-SX01. All terms and conditions of the BOA will apply and take precedence over any conflicting terms and conditions in this solicitation.
All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile,
or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;30003; ) ;3890AS001962-01; , Revision ;REV C; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall be bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10152 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST DRAWING; drawing number ( ;(30003); ) ;3890AS002122-01; , Revision ;REVISION E; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10153 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
Update #5 ·
CONTACT INFORMATION|4|N792.12|T1F|771-229-0418|michael.j.dickens5.civ@us.navy.mil|
ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19||||||||||||||||||||
WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (Combo)||TBD|N00383|TBD|TBD|TBD |TBD|||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1||
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11||||||||||||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13||||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5||||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1||
ROYALTY INFORMATION (APR 1984)|1||
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336413|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1||
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
The purpose of this amendment is to incorporate the following change:
1. The proposal submission date is extended to 31 October 2025.
2. All other terms and conditions remain unchanged.
\
This amendment is being issued to incorporate the following change:
1. The proposal submission date is extended to 25 September 2025.
2. All other terms and conditions remain unchanged.
\
The purpose of this amendment is to issue the following change:
1. The proposal due date is extended to 22 August 2025.
2. All other terms and conditions remain unchanged.
\
The purpose of this amendment is to incorporate the following change:
1. The solicitation date is extended to 9 July 2025.
2. All other terms and conditions remain unchanged.
\
This is a sole source spares solicitation for the procurement of three items.
The pursuant delivery order will be awarded against BOA N00383-23-G-SX01. All terms and conditions of the BOA will apply and take precedence over any conflicting terms and conditions in this solicitation.
All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile,
or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;30003; ) ;3890AS001962-01; , Revision ;REV C; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall be bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10152 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST DRAWING; drawing number ( ;(30003); ) ;3890AS002122-01; , Revision ;REVISION E; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10153 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
Update #4 ·
CONTACT INFORMATION|4|N792.12|T1F|771-229-0418|michael.j.dickens5.civ@us.navy.mil|
ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19||||||||||||||||||||
WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (Combo)||TBD|N00383|TBD|TBD|TBD |TBD|||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1||
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11||||||||||||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13||||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5||||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1||
ROYALTY INFORMATION (APR 1984)|1||
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336413|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1||
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
This amendment is being issued to incorporate the following change:
1. The proposal submission date is extended to 25 September 2025.
2. All other terms and conditions remain unchanged.
\
The purpose of this amendment is to issue the following change:
1. The proposal due date is extended to 22 August 2025.
2. All other terms and conditions remain unchanged.
\
The purpose of this amendment is to incorporate the following change:
1. The solicitation date is extended to 9 July 2025.
2. All other terms and conditions remain unchanged.
\
This is a sole source spares solicitation for the procurement of three items.
The pursuant delivery order will be awarded against BOA N00383-23-G-SX01. All terms and conditions of the BOA will apply and take precedence over any conflicting terms and conditions in this solicitation.
All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile,
or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;30003; ) ;3890AS001962-01; , Revision ;REV C; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall be bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10152 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST DRAWING; drawing number ( ;(30003); ) ;3890AS002122-01; , Revision ;REVISION E; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10153 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
Update #3 ·
CONTACT INFORMATION|4|N792.12|T1F|771-229-0418|michael.j.dickens5.civ@us.navy.mil|
ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19||||||||||||||||||||
WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (Combo)||TBD|N00383|TBD|TBD|TBD |TBD|||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1||
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11||||||||||||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13||||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5||||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1||
ROYALTY INFORMATION (APR 1984)|1||
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336413|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1||
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
The purpose of this amendment is to issue the following change:
1. The proposal due date is extended to 22 August 2025.
2. All other terms and conditions remain unchanged.
\
The purpose of this amendment is to incorporate the following change:
1. The solicitation date is extended to 9 July 2025.
2. All other terms and conditions remain unchanged.
\
This is a sole source spares solicitation for the procurement of three items.
The pursuant delivery order will be awarded against BOA N00383-23-G-SX01. All terms and conditions of the BOA will apply and take precedence over any conflicting terms and conditions in this solicitation.
All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile,
or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;30003; ) ;3890AS001962-01; , Revision ;REV C; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall be bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10152 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST DRAWING; drawing number ( ;(30003); ) ;3890AS002122-01; , Revision ;REVISION E; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10153 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
Update #2 ·
CONTACT INFORMATION|4|N792.12|T1F|771-229-0418|michael.j.dickens5.civ@us.navy.mil|
ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19||||||||||||||||||||
WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (Combo)||TBD|N00383|TBD|TBD|TBD |TBD|||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1||
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11||||||||||||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13||||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5||||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1||
ROYALTY INFORMATION (APR 1984)|1||
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336413|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1||
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
The purpose of this amendment is to incorporate the following change:
1. The solicitation date is extended to 9 July 2025.
2. All other terms and conditions remain unchanged.
\
This is a sole source spares solicitation for the procurement of three items.
The pursuant delivery order will be awarded against BOA N00383-23-G-SX01. All terms and conditions of the BOA will apply and take precedence over any conflicting terms and conditions in this solicitation.
All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile,
or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;30003; ) ;3890AS001962-01; , Revision ;REV C; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall be bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10152 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST DRAWING; drawing number ( ;(30003); ) ;3890AS002122-01; , Revision ;REVISION E; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10153 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
Update #1 ·
CONTACT INFORMATION|4|N792.12|T1F|771-229-0418|michael.j.dickens5.civ@us.navy.mil|
ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19||||||||||||||||||||
WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (Combo)||TBD|N00383|TBD|TBD|TBD |TBD|||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1||
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11||||||||||||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13||||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5||||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1||
ROYALTY INFORMATION (APR 1984)|1||
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336413|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1||
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
This is a sole source spares solicitation for the procurement of three items.
The pursuant delivery order will be awarded against BOA N00383-23-G-SX01. All terms and conditions of the BOA will apply and take precedence over any conflicting terms and conditions in this solicitation.
All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile,
or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;30003; ) ;3890AS001962-01; , Revision ;REV C; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall be bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10152 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST DRAWING; drawing number ( ;(30003); ) ;3890AS002122-01; , Revision ;REVISION E; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
QUALITY ASSURANCE REQUIREMENTS:
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT - Magnetic Particle Testing, PT - Penetrant Inspection, UT - Ultrasonic Testing, RT - Radiographic Testing, and VT - Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed below as satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 24-10153 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
Notice history
| Notice | Type | Posted |
|---|---|---|
| Valve, 4 in. FW A064- and similar replacement parts | Award Notice | |
| NRP, cooling interf - and similar replacement parts | Limited / Sole Source Justification | |
| This notice | Solicitation | |
| NRP, cooling interf - and similar replacement parts | Pre-Solicitation |
Similar open opportunities
| Opportunity | Agency | Set-aside | Responses due |
|---|---|---|---|
| Panel assembly | Naval Supply Systems Command | No set-aside | |
| Heat exchanger, air | Naval Supply Systems Command | No set-aside | |
| SSE, aircraft, materi, in repair/modification of | Naval Supply Systems Command | No set-aside | |
| Coolant pump assemb, in repair/modification of | Naval Supply Systems Command | No set-aside | |
| Panel, electronics, v, in repair/modification of | Naval Supply Systems Command | No set-aside |
On GovTribe
Work this opportunity
- Track it in your pipeline
- Find teaming partners
- Similar opportunities
- Ask GovTribe AI about this opportunity