Drill Sergeant Statues

Added: Jun 09, 2017 12:16 pm The following Line Items are added for reporting of installation labor hours.

CLIN 0003 is added as follows:

ITEM NO QUANTITY UNIT
0003 1 Each

ACCOUNTING FOR CONTRACT SERVICES REPORT
FFP
In accordance with the paragraph entitled "Accounting for Contract Services," the Accounting for Contract Services Report FY17.In accordance with the paragraph "Accounting for Contract Services", the Contractor shall provide an annual report to account for labor hours related to statue installation conducted on or before 30 September 2017. This report is due upon completion of services, but no later than 31 October 2017. Refer to website http://www.ecrma.mil/.

CLIN 0004 is added as follows:

ITEM NO QUANTITY UNIT
0004 1 Each

ACCOUNTING FOR CONTRACT SERVICES REPORT
FFP
In accordance with the paragraph entitled "Accounting for Contract Services," the Accounting for Contract Services Report FY18. In accordance with the paragraph "Accounting for Contract Services", the Contractor shall provide an annual report to account for labor hours related to statue installation conducted on or before 30 September 2018. This report is due upon completion of services, but no later than 31 October 2018. Refer to website http://www.ecrma.mil/.

Added: Jun 07, 2017 3:19 pm ITEM NO           QUANTITY           UNIT
0001                       1                  Each

Bronze Female Drill Sergeant Statue

3 dimensional 1 ¼ life size (72 inches in height) statue; statue shall be made of a cast bronze metal alloy; Statue shall be consistent with the attached images; Statue shall include Female Drill Sergeant hat, Left Sleeve-434th FA BDE Shoulder sleeve insignia, right sleeve US FLAG, Shoulder sleeve insignia - 101 Airborne DIV (Air Assault); Right Side of Chest: above pocket shall have name tape, Drill Sergeant Badge located on the right chest pocket; center chest shall have the insignia of grade (Rank); left side of chest above pocket(in order from top to bottom)- Combat Action Badge, Master Parachutist Badge, Air Assault Badge, U.S. Army tape. Statue shall include mounting: Statue shall be mounted on a bronze pedestal 2 feet wide by 2 feet long by 2 feet tall. A plaque shall be attached to the bronze pedestal. Plaque shall include the Drill Sergeant's Creed, US Government Seal on the upper left hand side and the Drill Sergeant's Badge on the upper right hand corner. The statue and pedestal will be mounted on a brown colored cement base 3 feet wide by 3 feet long by 1 foot tall and anchored to the concrete pad in front of building #6005. Statue shall be anchored and secured in a manner that will enable it to withstand 200 MPH winds and an additional 300 pounds of weight. Exact mounting location to be determined by Commander 95th AG BN prior to installation. Price shall include the statue, pedestal, concrete base, delivery and mounting. Upon notification of successful award, Final design and shop drawing shall be submitted to and approved by the Fort Sill Directorate of Public Works (DPW) and by the 95th AG BN Commander prior to proceeding with manufacture
of the statues. Notice to proceed shall not be given until Shop Drawings, to include but not limited to: certified foundation plans and load calculations, are approved by the Directorate of Public Works. A site visit is permitted. Contractor shall be onsite to direct and supervise the installation/mounting of the statues to the base.

ITEM NO          QUANTITY         UNIT
0002                     1                 Each

Bronze Male Drill Sergeant Statue

3 dimensional 1 ¼ life size (77 inches in height) statue; statue shall be made of a cast bronze metal alloy; Statue shall be consistent with the attached images; Statue shall include Drill Sergeant hat, Left Sleeve-434th FA BDE Shoulder sleeve insignia, right sleeve US FLAG, Shoulder sleeve insignia - 82nd ABN Div with Ranger Tab; Right Side of Chest: above pocket shall have name tape, Drill Sergeant Badge located on the right chest pocket; center chest shall have the insignia of grade (Rank); left side of chest above pocket(in order from top to bottom)- Combat Infantry Badge, Master Parachutist Badge, Air Assault Badge, U.S. Army tape. Statue shall include mounting: Statue shall be mounted on a bronze pedestal 2 feet wide by 2 feet long by 2 feet tall. A plaque shall be attached to the bronze pedestal. Plaque shall include the Drill Sergeant's Creed, US Government Seal on the upper left hand corner and the Drill Sergeant's Badge on the upper right hand corner. The statue and pedestal will be mounted on a brown colored cement base 3 feet wide by 3 feet long by 1 foot tall and anchored to the concrete pad in front of building #6005. Statue shall be anchored and secured in a
manner that will enable it to withstand 200 MPH winds and an additional 300 pounds of weight. Exact mounting location to be determined by Commander 95th AG BN prior to installation. Price shall include the statue, pedestal, concrete base, delivery and mounting. Upon notification of successful award, Final design and shop drawing shall be submitted to and approved by the Fort Sill Directorate of Public Works (DPW) and by the 95th AG BN Commander prior to proceeding with manufacture of the statues. Notice to proceed shall not be given until Shop Drawings, to include but not limited to: certified foundation plans and load calculations, are approved by the Directorate of Public Works. A site visit is permitted. Contractor shall be onsite to direct and supervise the installation/mounting of the statues to the base.

Responses to this RFQ shall be submitted via email to Tim Short (timothy.r.short6.civ@mail.mil) and Bill Boyer (William.e.boyer10.civ@mail.mil).

See attached solicitation for attachments for additional images for statue design.