Window Film SECTION 08 87 00.pdf

SECTION 08 87 00

WINDOW FILM

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Architectural Window Film:

1. Decorative Pattern

1.2 REFERENCES

A. ANSI Z97.1 - American National Standard for Safety Glazing Materials

Used in Buildings - Safety Performance Specifications and Methods of

Test.

B. ASHRAE - American Society for Heating, Refrigeration, and Air

Conditioning Engineers; Handbook of Fundamentals.

C. ASTM International (ASTM):

1. ASTM D 882 - Standard Test Method for Tensile Properties of

Thin Plastic Sheeting.

2. ASTM D 412 - Standard Test Methods for Vulcanized Rubber and

Thermoplastic Elastomers -- Tension.

3. ASTM D 624 - Standard Test Method for Tear Strength of

Conventional Vulcanized Rubber and Thermoplastic Elastomers

4. ASTM D 1004 - Standard Test Method for Tear Resistance (Graves

Tear) of Plastic Film and Sheeting.

5. ASTM D 1044 - Standard Method of Test for Resistance of

Transparent Plastics to Surface Abrasion (Taber Abrader Test).

6. ASTM D 2240 - Standard Method for Rubber Property - Durometer

Hardness.

7. ASTM D 2582 - Standard Test Method for Puncture-Propagation

Tear Resistance of Plastic Film and Thin Sheeting.

8. ASTM D 5895 - Standard Test Methods for Evaluating Drying or

Curing During Film Formation of Organic Coatings Using

Mechanical Recorders.

9. ASTM D 4830 - Standard Test Methods for Characterizing

Thermoplastic Fabrics Used in Roofing and Waterproofing.

10. ASTM E 84 - Standard Method of Test for Surface Burning

Characteristics of Building Materials.

11. ASTM E 308 - Standard Recommended Practice for

Spectrophotometry and Description of Color in CIE 1931 System.

12. ASTM E 903 - Standard Methods of Test for Solar Absorbance, Reflectance and Transmittance of Materials Using Integrating

Spheres.

13. ASTM E 1886 - Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems

Impacted by Missile(s) and Exposed to Cyclic Pressure

Differentials.

14. ASTM E 1996 - Standard Specification for Performance of

Exterior Windows, Curtain Walls, Doors and Impact Protective

Systems Impacted by Windborne Debris in Hurricanes.

15. ASTM F1642 - Standard Method of Test for Glazing and Glazing Systems Subject to Airblast Loadings

16. ASTM F2912 - Standard Specification for Glazing and Glazing

Systems Subject to Airblast Loadings.

D. Consumer Products Safety Commission 16 CFR, Part 1201 - Safety

Standard for Architectural Glazing Materials.

E. GSA-TS01 - Standard Test for Glazing and Glazing Systems Subject to

Airblast Loadings.

F. NFRC 100/200 (Formerly ASTM E903) - Standard Methods of Test for

Solar Absorbance, Reflectance and Transmittance of Materials Using

Integrating Spheres.

G. IES LM-83-12: IES Spatial Daylight Autonomy (sDA) and Annual

Sunlight Exposure.

H. ISO 16933, International Standard for Glass in Building: Explosion-resistant security glazing - Test and classification for arena air-blast testing.

I. Underwriters Laboratories Inc. (UL): UL 972 - Burglary Resisting

Glazing Material.

J. Window 6.3 - A Computer Tool for Analyzing Window Thermal

Performance; Lawrence Berkeley Laboratory.

1.3 DEFINITIONS

A. Light to Solar Gain Ratio: The ratio of visible light transmission to Solar Heat Gain Coefficient.

1.4 PERFORMANCE REQUIREMENTS

A. Flammability: Surface burning characteristics when tested in accordance ASTM E 84, demonstrating film applied to glass rated

Class A for Interior Use:

1. Flame Spread Index: no greater than 25.

2. Smoke Developed Index: no greater than 55.

B. Abrasion Resistance:

C. UV Light Rejection:

1.5 SUBMITTALS

A. Submit under provisions of Section 01 30 00.

B. Product Data: Manufacturer's current technical literature on each product to be used, including:

1. Manufacturer's Data Sheets.

2. Preparation instructions and recommendations.

3. Storage and handling requirements and recommendations.

4. Installation methods.

5. Mitigation Testing, ASTM F1642 / F2912 and/or GSA-TS01-2003.

C. Verification Samples: For each film specified, two samples representing actual film color and pattern.

D. Performance Submittals: Provide laboratory data of emissivity and calculated window U-Factors for various outdoor temperatures based upon established calculation procedure defined by the ASHRAE

Handbook of Fundamentals, Chapter 29, or Lawrence Berkeley

Laboratory Window 5.2 Computer Program.

1.6 QUALITY ASSURANCE

A. Manufacturer Qualifications: All primary products specified in this section will be supplied by a single manufacturer with a minimum of ten years experience.

1. Provide documentation that the adhesive used on the specified films is a Pressure Sensitive Adhesive (PSA).

B. Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five years demonstrated experience in installing products of the same type and scope as specified.

1. Provide documentation that the installer is authorized by the

Manufacturer to perform Work specified in this section.

2. Provide a commercial building reference list of 5 properties where the installer has applied window film. This list will include the following information:

a. Name of building.

b. The name and telephone number of a management contact.

c. Type of glass.

d. Type of film and/or film attachment system.

e. Amount of film and/or film attachment system installed.

f. Date of completion.

3. Provide a Glass Stress Analysis of the existing glass and proposed glass/film combination as recommended by the film manufacturer.

4. Provide an EFilm application analysis to determine available energy cost reduction and savings.

C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.

1. Finish areas designated by Architect.

2. Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.

3. Refinish mock-up area as required to produce acceptable work.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Follow Manufacturer's instructions for storage and handling.

B. Store products in manufacturer's unopened packaging until ready for installation.

C. Store and dispose of hazardous materials, and materials contaminated by hazardous materials, in accordance with requirements of local authorities having jurisdiction.

1.8 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.9 WARRANTY

A. At project closeout, provide to Owner or Owners Representative an executed current copy of the manufacturer's standard limited warranty against manufacturing defect, outlining its terms, conditions, and exclusions from coverage.

B. In order to validate warranty, installation must be performed by an

Authorized 3M dealer and according to Manufacturer's installation instructions. Verification of Authorized 3M dealer can be confirmed by submission of active 3M dealer code number.

PART 2 PRODUCTS

2.1 ARCHITECTURAL FINISH FILMS

A. Architectural Finish Films: A white, frosted, print embossed film that simulates sand blasted glass and matches. It is ideal for semi privacy while still allowing good light transmission.

B. Material Properties:

1. General: Glass finish field applied application to glass material as visual opaque or decorative film.

2. Film: Polyester

3. Decorative Pattern: See Schedule of Finishes 09 06 00.

4. Adhesive: Acrylic, Pressure Sensitive, Permanent

5. Liner: Silicone-coated Polyester

6. Thickness (Film and Adhesive without Liner): 2 mils (50.8 microns)

7. Fire Performance: Surface burning characteristics when tested in accordance with ASTM E84, Class A:

a. Flame Spread: 25 maximum.

b. Smoke Developed: 450 maximum.

C. Optical Performance:

1. Decorative Polyester Glass Finish Decorative Glazing Film applied to 3mm thick clear glass (ASTM E 903, ASTM E 308):

a. Ultraviolet Transmittance: 25 percent.

b. Visible Light Transmittance: 48 percent.

c. Visible Light Reflectance: 27 percent.

d. Solar Energy Absorbed: 25 percent.

e. Infra-Red Transmission: 60 percent.

f. Shading Coefficient at .55

PART 3 EXECUTION

3.1 EXAMINATION

A. Film Examination:

1. If preparation of glass surfaces is the responsibility of another installer, notify Architect in writing of deviations from manufacturer's recommended installation tolerances and conditions.

a. Glass surfaces receiving new film should first be examined to verify that they are free from defects and imperfections, which will affect the final appearance.

2. Do not proceed with installation until glass surfaces have been properly prepared and deviations from manufacturer's recommended tolerances are corrected. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result under the project conditions.

3. Commencement of installation constitutes acceptance of conditions.

3.2 PREPARATION

A. Clean surfaces thoroughly prior to installation.

B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

C. Refer to Manufacturer's installation instructions for methods of preparation for Impact Protection Adhesive or Impact Protection

Profile film attachment systems.

3.3 INSTALLATION

A. Film Installation, General:

1. Install in accordance with manufacturer's instructions.

2. Cut film edges neatly and square at a uniform distance of 1/8 inch (3 mm) to 1/16 inch (1.5 mm) of window sealant. Use new blade tips after 3 to 4 cuts.

3. Spray the slip solution, composed of one capful of baby shampoo or dishwashing liquid to 1 gallon of water, on window glass and adhesive to facilitate proper positioning of film.

4. Apply film to glass and lightly spray film with slip solution.

5. Squeegee from top to bottom of window. Spray slip solution to film and squeegee a second time.

6. Bump film edge with lint-free towel wrapped around edge of a 5-way tool.

7. Upon completion of film application, allow 30 days for moisture from film installation to dry thoroughly, and to allow film to dry flat with no moisture dimples when viewed under normal viewing conditions.

3.4 CLEANING AND PROTECTION

A. Remove left over material and debris from Work area. Use necessary means to protect film before, during, and after installation.

B. Touch-up, repair or replace damaged products before Substantial

Completion.

C. After application of film, wash film using common window cleaning solutions, including ammonia solutions, 30 days after application.

Do not use abrasive type cleaning agents and bristle brushes to avoid scratching film. Use synthetic sponges or soft cloths.

---END---

--- INTENTIONALLY BLANK ---