WDZ Tool Software Development Specification volume IV .pdf

For Official Use Only

Weapon Danger Zone Tool Software Specification Document

Volume IV - Requirements Versions 10.6.1.0.4

Last Updated: November 2020

This document has been approved for documentary release to the government(s) of _______________________ (or members of The Technical Cooperation Program (TTCP) (which include the United Kingdom, Canada, Australia and New Zealand).

It is not the intention of the US Marine Corps or the US Government to provide information, technology, training or education without concurrence or approval from appropriate organizations, departments or agencies, per the governing US Laws, National Disclosure Policy, and Department of Defense policy and directives.

This information is furnished upon the condition that it or knowledge of its possession will not be released to another nation without specific authority from the U.S. Marine Corps; that it will not be used for other than military purposes; that individual or corporate rights originating in the information, whether patented or not, will be respected and; that the information will be provided the same degree of security afforded it by the Department of Defense of the United States. Regardless of any other markings on this document, it may not be declassified or downgraded without the written approval of the originating U.S. agency.

(WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C., App. 2401 et seq.), as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25.

Commented [A1]: Remove for US Documents

Commented [A2]: Remove for US Documents

Record of Changes *A - Added M - Modified D – Deleted

VERSION

NUMBER DATE

NUMBER OF FIGURE,

TABLE OR

PARAGRAPH

A* M D

TITLE OR BRIEF DESCRIPTION

CHANGE

REQUEST

NUMBER

1.0 01/12/2012 Moved Requirements from Appendix D of Software Development Specification Document to its own volume.

1.1 03/28/2012 Section 2.2.13 A Add Version 9.3.1.2.1 03/28/2012 Section 2.3 M Updated pending requirements

1.2 04/16/2012 Distribution Statement,2 & Lexicon

M Recommendations from Contractor

1.3 05/07/2012 Acceptance Page M Updated the document number & Corrected Version number

1.4 05/09/2012 Section 2 M Changed requirements origination 05/09/2012 Table 2-2 & 2-3 M Changed verbiage of BridgeTrak 05/09/2012 Table 2-4 M Corrected spelling error 05/09/2012 Section 1.3 M Changed to ArcMap Extension

1.5 05/14/2012 Section 2 M Changed verbiage

1.6 09/24/2012 Section 2.2.13 & 2.3 M Changed references from CSR to Battelle

2.0 11/16/2012 Section 2.2.13 & 2.3 M Updated to version 9.3.1.2.1 & 10.0.0.4.2

2.1 02/05/2013 M Added version 10.1.0.0.1

3.0 05/28/2013 M Updated to version 9.3.1.2.2, 10.0.0.4.3 &

10.1.0.1.2

3.1 07/31/2013 M Change Contractor Name

3.2 08/20/2013 Section 2.2.14 A Added Version 9.3.1.2.2

3.3 08/20/2013 Section 2.3 M Updated pending requirements

4.0 09/09/2013 M Updated to versions 9.3.1.2.3, 10.0.0.4.4 &

10.1.0.1.3

4.1 10/22/2013 Section 2.2.15 A Added Version 9.3.1.2.3

4.2 10/22/2013 Section 2.3 M Updated Pending Requirements

5.0 05/21/2014 A Updated to versions 10.0.0.4.5, 10.1.0.1.4

& 10.2.0.0.2

6.0 04/01/2015 Section 2.2.16 A Added version 10.0.0.4.6, 10.1.0.1.5 & 10.2.0.0.3

6.1 06/29/2015 Section 2.3 M Updated Pending Requirements

6.2 11/02/2015 Section 22.18 A Hotfix for target/terrain type

11/12/2015 Section 22.19 A Added version 10.1.0.1.7, 10.2.0.0.5 & 10.3.0.0.3

6.3 02/29/2016 Section 22.19 M Removed Version 10.1.0.1.7 Section 2.3 M Updated Pending Requirements

7.0 04/23/2016 Section 22.20 A Added Release 10.2.0.0.5, 10.3.0.0.4 & 10.3.1.0.1

7.1 07/18/2016 Section 1.4 M Added Volume VI

8.0 11/02/2016 Section 2.2.21 A Added Release 10.2.0.0.6, 10.3.0.0.5 &

10.3.1.0.2

8.1 11/14/2016 Section 2.4 A Added Outstanding Bugfixes

A Added definition for Impact columns

8.2 12/26/2016 Section 1.1 M Updated WDZ Definition

8.3 02/16/2017 ALL M Sanitized document for FMS use

9.0 05/08/2017 Section 1.3 D Removed Outstanding Issues section

10.0 11/02/2017 Section 1.2.22 A Added 10.4.1.0.2 release requirements Removed Status column from requirements tables

Changed Issue number to use Jira numbers

11.0 12/04/2017 Section 1.2.23 A Added 10.4.1.0.3 release requirements

12.0 04/27/2018 Page 2 A Added distribution statement

Added FOUO

13.0 06/28/2018 Section 1.2.24 A Added 10.4.1.0.4 release requirements

14.0 11/26/2018 Section 1.2.25 A Added 10.4.1.0.5 release requirements

14.1 01/11/2019 Distribution

Statement M Added requested verbiage for FMS documents

15.0 05/09/2019 Section 1.2.26 A Added 10.6.1.01 release requirements

16.0 05/30/2019 Section 1.2.27 A Added 10.6.1.0.2 release requirements

Section 1.1 M Updated to include Volume VI

17.0 09/20/2019 Section 1.2.28 A Added 10.6.1.0.3 release requirements

17.1 11/18/2019 Section 1.1 M Corrected Volumes I, II, III, VI & V to

Volumes I, II, III, IV & V

18.0 11/04/2020 Section 1.2.29 A Added 10.6.1.0.4 release requirements Title Page M Updated Contract Number ALL M Updated to version 10.6.1.0.4 ALL M Replaced all references to “WDZT” with

“WDZ Tool”

Title M Changed “RTAM Division” to “Range and Training Programs Division, RTAM Branch”

Weapon Danger Zone Tool

These documents define the Weapon Danger Zone Tool versions 10.6.1.0.4 configuration and test plan to reflect Weapon Danger Zone Tool software as delivered to United States Marine Corps Range and Training Area Management.

27 September 2011

Prepared For:

United States Marine Corps

Training and Education Command Range and Training Area Management

Document Number: WDZ-20-010

Contract Numbers: M67854-20-F-3003

PROPRIETARY INFORMATION

Distribution authorized to U.S. Government agencies and their contractors for administrative or operational use. Other requests for this document must be referred to Commanding General, U.S.

Marine Corps Training and Education Command, ATTN: Range and Training Programs Division, RTAM Branch, Quantico, VA 22134.

Originated By: WDZ Configuration Manager

Approved By: WDZ Project Leader

Accepted By:

Document Status: Delivered Documentation

This Page is Intentionally Left Blank

Table of Contents

1. Introduction

2 Requirements

1.1. Baseline Requirements

1.2. Completed Requirements

1.2.1. Version 9.2.4.2

1.2.2. Version 9.2.4.5

1.2.3. Version 9.2.4.7

1.2.4. Version 9.2.4.8

1.2.5. Version 9.2.4.9

1.2.6. Version 9.2.4.10

1.2.7. Version 9.2.4.10.1

1.2.8. Version 9.2.4.11

1.2.9. Version 9.2.4.11.2

1.2.10. Version 9.2.4.15

1.2.11. Version 9.2.4.16

1.2.12. Version 9.2.4.16.1

1.2.13. Version 9.3.1.2.1, 10.0.0.4.2 & 10.1.0.0.1

1.2.14. Version 9.3.1.2.2, 10.0.0.4.3 & 10.1.0.1.2

1.2.15. Version 9.3.1.2.3, 10.0.0.4.4 & 10.1.0.1.3

1.2.16. Version 10.0.0.4.5, 10.1.0.1.4 & 10.2.0.0.2

1.2.17. Version 10.1.0.1.5, 10.2.0.0.3 & 10.3.0.0.1

1.2.18. Version 10.1.0.1.6, 10.2.0.0.4 & 10.3.0.0.2

1.2.19. Version 10.2.0.0.5 & 10.3.0.0.3

1.2.20. Version 10.2.0.0.6, 10.3.0.0.4 & 10.3.1.0.1

1.2.21. Version 10.2.0.0.7, 10.3.0.0.5 & 10.3.1.02

1.2.22. Version 10.4.1.0.2

1.2.23. Version 10.4.1.0.3

1.2.24. Version 10.4.1.0.4

1.2.25. Version 10.4.1.0.5

1.2.26. Version 10.6.1.0.1

1.2.27. Version 10.6.1.0.2

1.2.28. Version 10.6.1.0.3

1.2.29. Version 10.6.1.0.4

Appendix A: Glossary ..........................................................................................................................................A-1

Appendix B: Acronyms ........................................................................................................................................ B-1

Tables and Figures

Table 2 - 1: Key to Issue Number Codes Table 2 - 2: Key to Status Descriptions Table 2 - 3: Baseline Requirements Table 2 - 4: Version 9.2.4.2 Requirements Table 2 - 5: Version 9.2.4.5 Requirements Table 2 - 6: Version 9.2.4.7 Requirements Table 2 - 7: Version 9.2.4.8 Requirements Table 2 - 8: Version 9.2.4.9 Requirements Table 2 - 9: Version 9.2.4.10 Requirements Table 2 - 10: Version 9.2.4.10.1 Requirements Table 2 - 11: Version 9.2.4.11 Requirements Table 2 - 12: Version 9.2.4.11.2 Requirements Table 2 - 13: Version 9.2.4.15 Requirements Table 2 - 14: Priority Ranking Table 2 - 15: Version 9.2.4.16 Requirements Table 2 - 16: Version 9.2.4.16.1 Requirements Table 2 - 17: Version 9.3.1.2.1, 10.0.0.4.2 & 10.1.0.0.1 Requirements Table 2 - 18: Version 9.3.1.2.2, 10.0.0.4.3 & 10.1.0.1.2 Requirements Table 2 - 19: Version 9.3.1.2.3, 10.0.0.4.4 & 10.1.0.1.3 Requirements Table 2 - 20: Version 10.0.0.4.5, 10.1.0.1.4 & 10.2.0.0.2 Requirements Table 2 - 21: Version 10.1.0.1.5, 10.2.0.0.3 & 10.3.0.0.1 Requirements Table 2 - 22: Version 10.1.0.1.6, 10.2.0.0.4 & 10.3.0.0.2 Requirements Table 2 - 23: Version 10.2.0.0.5 & 10.3.0.0.3 Requirements Table 2 - 24: Version 10.2.0.0.6, 10.3.0.0.4 & 10.3.1.0.1 Requirements Table 2 - 25: Version 10.2.0.0.7, 10.3.0.0.5 & 10.3.1.0.2 Requirements Table 2 - 26: Version 10.4.1.0.2 Requirements Table 2 - 27: Version 10.4.1.0.3 Requirements Table 2 - 28: Version 10.4.1.0.4 Requirements Table 2 - 29: Version 10.4.1.0.5 Requirements Table 2 - 30: Version 10.6.1.0.1 Requirements Table 2 - 31: Version 10.6.1.0.2 Requirements Table 2 - 32: Version 10.6.1.0.3 Requirements

1. Introduction

1.1 Purpose

The Weapon Danger Zone (WDZ) Tool is a software application that currently runs as an ArcMap toolbar. The WDZ Tool allows the user to create and modify custom Weapon Danger Zones (WDZs). The WDZ engine is defined in Volumes I, II, III, IV & V. The User Interface is defined in Volume VI.

A Weapon Danger Zone (WDZ) is defined as a three-dimensional region that encompasses the ground and airspace required for horizontal and vertical containment of impact and post- impact effects (i.e. projectiles, fragments, debris, and components) resulting from the firing, launching, release and /or detonation of aviation-delivered ordnance. This three-dimensional zone accounts for weapon accuracy, failures, ricochets, and broaches/porpoising of a specific weapon/munition type delivered by a specific aircraft type. WDZs represent the minimum safety requirements designed for aviation weapons training on DOD ranges.

1.2 AIM

Weapon Danger Zones are classified by weapon type and aircraft type; the general principles described here apply to air-to-ground weapon systems. The aim of this document is to describe the general principles as applied with each weapon system in the development of the appropriate

WDZ.

1.3 Scope

This document along with the associated documents as defined in paragraph 1.4 applies to the development of the WDZ Tool.

1.4 Related Documents

This is one of a series of documents that are concerned with the development of WDZs for a variety of weapon systems for use on training ranges. The following is a list of the current Software Development Documents for WDZ:

WDZ Tool Software Development Specification Volume I – Source Code & Project Overview WDZ Tool Software Development Specification Volume II – Data Cube WDZ Tool Software Development Specification Volume III – WDZ Specifications WDZ Tool Software Development Specification Volume IV – Requirements WDZ Tool Software Development Specification Volume V – Test Plan WDZ Tool Software Development Specification Volume VI – User Interface

1.5 Glossary and Acronyms

A glossary and list of acronyms used in this document are provided in Appendices A and B, respectively.

2 Requirements Baseline requirements are requirements derived from the initial Statement of Work (SOW) for the WDZ extension.

Table 2 - 1: Key to Issue Number Codes Entry in Issue # Column Description Number in Table 2-3 From an entry in the Statement of Work Number in Tables 2-4 through 2-18 A support request issue number

CMWG Request Issue was requested by the CMWG

Internal Maint Maintenance changes made by Software Developers. These changes were necessary for Code cleanup and/or new development

Table 2 - 2: Key to Status Descriptions

Status Entry Description ArcGIS Function These requirements can already be performed using existing ArcMap tools.

Canceled Requirement added then returned to original state Completed Requirement change has been completed and implemented into the referenced version of the tool.

Data not available Data are not available to satisfy this requirement change at this time.

Duplicate of xxxx These requirements have another requirement that specifies the same request, where “xxxx” refers to the issue number of the duplicate request

Information Only These requirement changes contain specific instructions, but do not require any work product.

On Hold The request is currently waiting on additional data or is on hold by the CMWG

Ongoing These requirements are continuous Partially Complete All parts of the change request have not yet been completed Pending No portion of the change request has been implemented Satisfied by use of BridgeTrak

BridgeTrak is the help desk software. All help desk issues and software change request are entered into BridgeTrak.

1.1. Baseline Requirements

Table 2 - 3: Baseline Requirements Issue # Requirement Status

4.4.07 Calculate the area of WDZ - on and off Range Completed

6.5.04 Compatible with GIS and PFPS/JMPS applications Duplicate of 4.8.00

4.1.25 Contact information of the program manager, deputy program manager, and Service representatives available through UT Completed

4.6.12 Evaluate existing data and make recommendations Completed

6.2.00 Primary distribution will be via website Completed

6.2.00 Add New Foreign Services Completed

6.2.00 Existing Foreign Service footprints will be included Data Not available

4.5.01 Variables for generating WDZ Information only

4.6.07 Product approval process Information only

4.7.02 Database Labeling Completed

9.1.00 1-year warranty Information only

4.3.00 Risk analysis on any user defined area Duplicate of

4.2.13

4.1.21 Risk Analysis for multiple WDZs/Targets Completed

4.1.23 Risk Analysis for target location Completed

4.2.13 Risk Analysis for single points and user-defined areas Completed

4.4.06 Risk Analysis for single points and user-defined areas Duplicate of 4.2.13

4.1.26 Ability to submit change/problem request via UT Satisfied by use of BridgeTrak

4.1.26 Trouble Report and Status to be visible via UT until confirmed corrected/closed Satisfied by use of BridgeTrak

4.6.08 Initial release correction period Information only

4.1.24 Online Help Manual Completed

3.1.01 Accessible to all authorized users (US and allied) Completed

4.4.09 Email PM & DPM for access request and access approval Completed

4.4.09 List of all approved/pending users accessible by the PM & DPM Completed

4.4.09 Password protected website meeting all restrictions of DOD and each service Completed

4.4.09 PM & DPM can send emails to all user (individually and groups) Completed

6.2.00 Security Controls to prohibit unauthorized access Completed

6.5.10 Allow authorized Ranges access to any WDZ in library at any time Completed

4.2.11 Create footprints on user-defined maps consisting of SDSFIE range data layers Completed

4.2.11 Work within the existing Services SDSFIE compliant GIS data Completed

4.8.00 Web-enabled program Completed

3.2.02 Window-like user interface Completed

4.4.02 Desktop and Web versions (requiring only login/password, Internet connection and Browser) Completed

4.6.01 WDZ tool, User Manual and on-line tutorial will be placed on a password protected website Completed

4.9.00 Maintain Site license and certification for website Completed

4.9.00 Program, software and all deliverables will be fully owned by the government Information only

4.2.11 Operate in an ARC GIS environment Completed

4.2.17 Ensure the compatibility and interoperability of WDZs with GIS range maps Completed

Issue # Requirement Status

4.2.07 Add or Edit Targets and ACCs Completed

4.2.08 Select multiple targets or DMPI by entering coordinates Completed

4.2.08 Select multiple targets or DMPI by mouse click Completed

4.2.09 Add new target by entering target coordinate system data Completed

4.2.12 Select Target type Completed

6.5.06 Search WDZ Completed

4.1.19 Display Target Centric or Launch Centric Completed

4.1.20 Insert Legend / Text anywhere on map ArcGIS Function

4.1.22 Change color of selected WDZ Duplicate of

4.2.17.2

4.2.02 Toggle Map Datums ArcGIS Function

4.2.02 Toggle Map Labels ArcGIS Function

4.2.03 Convert coordinate data Duplicate of

6.5.01

4.2.04 Toggle Labeling ArcGIS Function

4.2.04 Toggle Layer Annotation ArcGIS Function

4.2.05 Select Terrain Layer ArcGIS Function

4.2.06 Select Layer ArcGIS Function

4.2.10 Cut/Copy Paste Routines ArcGIS Function

4.2.10 Draw the attack line with ability to determine attack line variation ArcGIS Function

4.2.10 Include drawing tools, measuring devices ArcGIS Function

4.2.10 Rotate draw tools Completed

4.2.14 Toggle Scale Bar ArcGIS Function

4.2.15 Bookmark Tool ArcGIS Function

4.2.15 Zoom Tool ArcGIS Function

4.2.16 Print map legend ArcGIS Function

4.2.17.1 Select scale ArcGIS Function

4.2.17.2 Change color of selected WDZ ArcGIS Function

4.2.17.2 Overlay WDZs on map Completed

4.2.17.3 Print/Edit List of WDZ Completed

4.4.04 Undo Command ArcGIS Function

6.4.07 Print maps and layers ArcGIS Function

6.5.01 Convert coordinate data ArcGIS Function

6.5.06 Select WDZ Completed

4.1.01 Display WDZ so user can determine acceptability Completed

6.5.03 Display Existing WDZ Completed

4.1.17 Select WDZ by Service, Aircraft, Weapon Completed

4.1.07 Build WDZ for all footprints currently in user inventories Data Not available

4.4.08 Select WDZ by release conditions Completed

4.1.11 Select Weapon Release Parameters Completed

4.1.13 Mouse Manipulation to move/rotate WDZ Completed

4.1.14 Mouse Manipulation to define or change run-in, target or target area Completed

4.1.22 Combine WDZ Completed

4.2.08 Display composite WDZ on multiple targets Completed

4.2.10 Rotate WDZ Completed

6.5.09 Manipulate WDZ - repositioning, rotating, and reorienting Completed

Issue # Requirement Status

4.4.03 Select deviation change and manipulate WDZ Completed

3.1.01 Gather as much data as possible from all authorized sources Completed

4.6.05 Discard score data older than 10 years Ongoing

4.6.05 Gather Score data Ongoing

4.6.05 Provide method/data for producing WDZ to government if requested Completed

4.6.06 List all excluded (outlaying) data points and reason to exclude/include Ongoing

4.6.10 Examine gross error frequency of actual weapon scoring data - Notify Gov't of needed adjustments Ongoing

4.6.11 Make recommendations on weapon score data based on changes or trends Completed

6.1.01 Quarterly Data updates Ongoing

4.4.11 Requirements for CD distribution list Completed

4.6.04 All data evaluated and/or user to develop WDZ is considered part of the WDZ and deliverable to Gov't Information only

6.0.00 Deliverables required Information only

6.2.00 Compact Disk to be made available for necessary users Completed

7.0.00 Delivery Schedule Information only

10.0.00 Location of Hardcopy product delivery Information only

11.1.00 Fully owned by government Duplicate of

4.4.05

11.2.00 Life-time Contract Schedule Information only

12.0.00 Physical Security and safeguarding Information only

12.0.00 Send copy of DSS security inspections to Government Completed

12.5.00 Hours of operation Information only

12.6.00 Holiday Schedule Information only

3.2.01 WDZ approval Information only

3.2.03 Additional task agreement Information only

3.2.03 Skill sets required Information only

4.4.05 Fully owned by government Information only

4.5.03 Range type (basic) means no additional error budgets have been added to the footprints to account for aircrew tactics Information only

4.6.17 No software/system changes to fielded systems after gaining a certificate to operate without prior approval Information only

4.6.17 Obtain and Maintain a Certificate to operate Completed

4.6.19 Contractor shall maintain qualified employees Information only

4.6.21 Help Desk & Trouble Reports to be electronic and hard copy BridgeTrak

4.6.21 Help Desk & Trouble Response time < 48 hours BridgeTrak

4.7.01 Score data minimum requirements Information only

5.1.00 Duplicate of 3.2.03 Duplicate of

3.0.03

5.1.01 Description of PM Services and PMR requirements Information only

5.2.0 Training restrictions Information only

5.3.00 WDZ definitions Information only

6.1.00 Requirements for handling raw data (score data) received. Information only

6.1.02 All data collected restricted to use on this contract only Information only

6.3.00 WDZ Statistical Methodology Information only

7.1.00 Government Points of contact Information only

4.6.15 Quarterly Reviews Ongoing

Issue # Requirement Status

3.1.02 Continuous training and technical support Ongoing

3.1.04 Annual Examination of government-specified WDZs to ensure their standardization and verify operational credibility Ongoing

3.2.02 Review WDZs to ensure credibility Ongoing

3.2.03 Hardware, software engineering and technical support BridgeTrak

3.2.03 Implementation of system improvements; upgrades; modifications Ongoing

3.2.03 Training to the government and approved users Ongoing

4.1.26 Trouble Reports to be reviewed at quarterly reviews BridgeTrak

4.6.01 Maintain CD of Ultimate Tool, User Manuals and on-tutorials for distribution at request of Gov't Completed

4.6.09 Annual Review of Source Data Ongoing

4.6.14 Annual Conference Annual Task

4.6.16 Initial training Completed

4.6.20 Monthly Progress reports Ongoing

5.1.02 Evaluate latest technological upgrades Ongoing

5.1.02 Maintain compatibility with current Microsoft Windows OS Ongoing

5.1.03 Routine Database Maintenance Ongoing

5.1.04 Website maintenance and support Ongoing

5.1.05 Help Desk Reports to be reviewed at quarterly reviews BridgeTrak

5.1.05 Maintain Help Desk Support during normal business hours Completed

6.4.09 Process for handling future requirements Completed

3.1.01 Meet all safety standards Completed

4.1.00 Support range safety policy Completed

4.1.04.3 Instantly available to the user Completed

4.6.18 Certification and Accreditation Process Completed

4.2.08 Calculate restrictions based on user-defined conditions Completed

4.4.01 Compatible with other applications Duplicate of

4.8.00

4.8.00 Compatible for integration with RFMSS, RMTK, PFPS/JMPS, and GIS applications Completed

6.4.04 Compatible for integration with RFMSS, RMTK, PFPS/JMPS, and GIS applications Duplicate of 4.8.00

4.1.09 Third party module integration Completed

3.1.01 Collect and analyze test data Ongoing

4.4.01 Most readily available and advanced programming language, compatible with all services Ongoing

3.1.01 Develop WDZs that meet the specified government requirements Completed

3.1.01 Development of new WDZs shall include but are not limited to: weapon failure modes and the associated predicted effects on the weapon, ballistic profiles (both powered and un-powered), weapon guidance, virtual modeling, and ricochet affects

Ongoing

3.1.01 Rely on new scoring and modeling of virtual impacts based upon weapon/aircraft capabilities Ongoing

4.3.00 Build WDZ -- Method & use of data Completed

4.3.00 Max-energy WDZ - limited use Completed

4.6.03 Standardized format for sharing WDZs Completed

4.6.13 Acceptable data set to calculate WDZs Completed

4.3.00 Accept inputs and changes to update legacy footprints Completed

4.2.08 Generate Report for Risk Analysis Completed

4.2.17.2 Risk analysis of any point/area within the WDZ Completed

Issue # Requirement Status

4.6.01 Electronic copies of updated and/or newly developed WDZs and supporting data shall be submitted to HQ ACC/A3AR for approval Ongoing

6.4.04 Drop-down menu / tool bar functionality Completed

6.3.01 Containment level range and default value Completed

6.3.02 Toggle containment levels Completed

6.5.05 Sort WDZ for each target by aircraft and weapon Completed

4.8.00 Export Function compatible with other applications Completed

4.6.13 Support data sorts by aircraft type, range type, delivery event, release parameters, and weapons type Completed

4.2.01 Display WDZ and relational items (map) in 3-D solid modeling Completed

4.2.17 Display WDZ in 3-D block view Completed

6.4.02 Display WDZ in 3-D block view Completed

6.4.03 View all data in a common map scale or map datum of their choosing Completed

4.1.02 3-D View including: (1) terrain profile, (2) weapon trajectories, (3) broached/ricochet ordnance, (4) fragmentation, and (5) explosive effects Completed

4.1.03 Modification of dimensions of existing WDZ by authorized user Completed

4.1.04.1 Toggle between different platforms, airspeeds, dive angles, range types, altitudes, and terrain types Completed

4.1.12 Re-engineer WDZ by modifying release parameters - subject to approval?? Completed

4.1.15 Build Composite WDZ Completed

4.1.16 Toggle Terrain Effects Completed

4.4.10 Toggle between different platforms, airspeeds, dive angles, range types, altitudes, and terrain types Completed

4.6.03 Import / Export functionality required for sharing WDZs Completed

6.4.00 Produce WDZs to the prescribed degree of selectable probability Completed

6.4.03 Save WDZ Completed

6.4.05 Build Composite WDZ Completed

6.4.08 Calculate restrictions for at least 10 targets Completed

6.4.08 Calculate restrictions for at least 10 WDZ Completed

6.5.00 Save and Catalog WDZ Completed

6.5.02 Save WDZ Completed

6.5.04 Build Composite WDZ Completed

6.5.07 Select, retrieve and modify WDZ via a library search Completed

6.5.08 Re-engineer WDZ by modifying release parameters Completed

6.5.02 Archive WDZ no longer in use Completed

3.1.03.1 Build WDZ that is Range specific Completed

3.1.03.2 Factor in terrain and target effects if resultant WDZ is affected Completed

4.1.00 Build WDZ based on aircraft and weapon Completed

4.1.04.2 Delivery parameters should be at every 50 KTAS, every 5,000 feet altitude block, and every 5 degrees of pitch Completed

4.1.04.2 WDZs pre-engineered to user Completed

4.1.05 Incorporate the Joint Munitions Effectiveness Manual Completed

4.1.06 Show the explosive effects based on previously approved JMEM tables Completed

4.1.10 Build WDZ based on outlaying impacts Completed

4.1.21 Save WDZ (acceptable & unacceptable) with risk analysis Completed

4.5.02 Incorporate Terrain Effects on munitions Completed

4.6.02 WDZ signed and certified by contractor Ongoing

Issue # Requirement Status

4.6.13 Build WDZ with score data or modeling Completed

6.4.01 Build WDZ based on the weapon algorithms Completed

6.4.06 Modify and Save WDZ based user-input azimuth Completed

4.1.18 Rotate WDZ (existing) based user-input azimuth Completed

4.2.08 Manipulate single WDZ within composite Completed

6.4.00 Graphically depict probability of impacts either by actual hits or by modeling the percentage of hits inside a WDZ Completed

6.4.06 Display modified WDZ on Map Completed

4.1.08 Add new weapons Ongoing

4.1.09 Update weapon data Ongoing

1.2. Completed Requirements

1.2.1. Version 9.2.4.2

Table 2 - 4: Version 9.2.4.2 Requirements

Issue # Requirement Change Status Internal Maint Moved WDZ Name to the first position in the batch tool Completed Internal Maint Changed "Delete" to "Uncombine" for Composites Completed

Internal Maint Modified setup to set primary display fields and turn on map tips Completed 217 Added color change tool Completed 216 Added off-range risk tool Completed 219 Added point risk tool Completed 627 Added WDZ Area Tool Completed

Internal Maint Added message to include the minus sign for dive angles Completed

Internal Maint Added target to the batch tool grid Completed Internal Maint Added UTM, DD, DDM, DMS & MGRS coordinate tabs Completed

CMWG Request Added Area to ACC Completed CMWG Request Added coordinates to ACC Properties Completed CMWG Request Added ACC Point layer Completed CMWG Request Added Batch Import/Export Completed

CMWG Request Added import/Export option to WDZ Manager Completed CMWG Request Changed bomb spacing for string of bombs to feet Completed CMWG Request Changed airspeed units to KTAS Completed CMWG Request Change WDZ Area to display area in square acres Completed CMWG Request Modify risk dialog to display 0 instead of 0:1 Completed CMWG Request Disabled ACC Hardness Completed

Internal Maint Added Range Type for legacy WDZs Completed

Internal Maint Applied an alpha sort to target list Completed

Internal Maint Added commas in risk values where needed Completed Internal Maint Round headings to integers Completed

CMWG Request Moved WDZ setup tool in the toolbar Completed 347 Added name properties and allow users to modify Completed

Issue # Requirement Change Status

CMWG Request Added WDFA_ID to Select WDZ dialog for legacy Completed Internal Maint Added * for all required fields on all dialogs Completed

CMWG Request Allow user to resize dialogs when necessary Completed CMWG Request Changed map tips for layers to display the name field Completed CMWG Request Changed composite WDZ List to display WDZ name Completed

Internal Maint Added limitations on changes to composite WDZs Completed Internal Maint Added a confirmation message to delete functions Completed

CMWG Request Changed position of layers in the TOC Completed Internal Maint Changed Risk values to 2 decimal places Completed

626 Added spaces for missing values on Batch export Completed 574 Changed terminology on launch-centric layout template Completed

Internal Maint Turned on auto-complete for Event comboboxes Completed Internal Maint Changed Magnetic Update to allow 0 as a valid entry Completed Internal Maint Added mag declination to WDZ table Completed

CMWG Request Added creator and create date to WDZ Completed Internal Maint Modified Target radius to allow 0 as a valid entry Completed

CMWG Request Added weapon description to General tab Completed Internal Maint Changed Slant Range to Release Range Completed Internal Maint Removed Range Feature class name from Setup Completed Internal Maint Removed Range Type from Setup Completed Internal Maint Updated URL for Mag Declination Link on Setup Completed Internal Maint Added an example for each coordinate type Completed Internal Maint Added validation for angle/heading entries to 0-360 Completed Internal Maint Removed the Create/Undo Create buttons from the Create WDZ Completed

CMWG Request Added default containments to Setup Completed CMWG Request Added line/area targets Completed CMWG Request Added geometry type to target manager Completed

1.2.2. Version 9.2.4.5

Table 2 - 5: Version 9.2.4.5 Requirements

2266 Added vertical hazard value Completed

CMWG

Request Changed max length of name fields to 50 characters Completed

Internal Maint Changed Off-Axis Angle header to Off-axis Heading Completed Internal Maint Added check for string of bomb on Modify by Terrain Completed Internal Maint Removed Aircraft_Heading_at_launch from Batch tool Completed Internal Maint Renamed "Launch Point to target" to Off-Axis Angle" Completed Internal Maint Renamed "Launch Point to target Heading" to Off-Axis Heading" Completed Internal Maint Updated messages and summary to reflect Off-Axis Heading Completed Internal Maint Changed width of Weapon Description label to 250 Completed

1.2.3. Version 9.2.4.7

Table 2 - 6: Version 9.2.4.7 Requirements

353 Changed color selection dialog to symbol selector Completed 489 Added option to disable string of bomb by weapon Completed 973 Added a condition to set the launch mode for AGM-114 K/M to indirect Completed

1153 Changed inert & live radius on 1000 lb FF & RET Completed

CMWG

Request Enabled AGM114/AGM65/TOW/TOW 2B Completed

CMWG

Request Added MQ9 / GBU38 Completed

CMWG

Request Added "(Ground Range)" label to Event tab Completed

CMWG

Request Added TOW/TOW 2B Completed

CMWG

Request

Removed BDU-48 from MK82 description and added BDU-48 back to available legacy WDZs list Completed

CMWG

Request Changed Hellfire events to "Dive Bomb" & "Level" Completed

CMWG

Request Removed AC-130 / 30mm Completed

Internal Maint Added Hellfire GUI to Create WDZ Completed Internal Maint Added roll tip-off message Completed Internal Maint Added validation to check if WDZ could be dropped live Completed Internal Maint Changed GBU-24 to GBU-24 modes 1 through 4 Completed Internal Maint Changed AGM-114 to AGM 114 A-F & AGM-114 K/M Completed Internal Maint Added launch mode to layout Completed

1.2.4. Version 9.2.4.8

Table 2 - 7: Version 9.2.4.8 Requirements

CMWG Request Added CV22 / 50 CAL & 7.62mm Completed

CMWG Request Added MQ-9 / GBU-38 Completed CMWG Request Added SH-60 / 50 CAL Completed CMWG Request Changed Event type for CV22s Completed

1.2.5. Version 9.2.4.9

Table 2 - 8: Version 9.2.4.9 Requirements

Internal Maint Added feature to save and restore user range profiles Completed Internal Maint Added release condition validation for JDAM Completed Internal Maint Removed unused aircraft/weapon combinations Completed

1.2.6. Version 9.2.4.10

Table 2 - 9: Version 9.2.4.10 Requirements

CMWG Request Changed JDAM interface to include off-axis angle Completed CMWG Request Added area F for TOW/TOW 2B Completed CMWG Request Changed Event types for Hellfire and guns Completed

1.2.7. Version 9.2.4.10.1

Table 2 - 10: Version 9.2.4.10.1 Requirements

1368 Removed "No targets/WDZ/ACCs are checked" message Completed

1413 Added Signature box to all templates. Completed

1561 Added Weapon Information button for AGM-114 Completed

CMWG Request Changed Hellfire weapon descriptions Completed

CMWG Request Added AGM-114 Area F warning Completed

Internal Maint Added min/max release range warning when achievable limits are exceeded Completed

Internal Maint Set AGM-114 to live only Completed

1.2.8. Version 9.2.4.11

Table 2 - 11: Version 9.2.4.11 Requirements

351 Added off-range area, on-range area, total area and percent off-range to Calculate WDZ Area Completed

546 Added Create ACC from Point Risk Completed 751 Added a catch to correctly import files edited with Excel Completed

895 Changed name of Off-Range Area to Calculate WDZ Area Completed 1251 Added CSV Export to the WDZ Manager Dialog Completed 1292 Removed restrictions to perform risk analysis on composites Completed 1360 Added Back/Cross/Down range values to Summary Completed 1432 Removed messages that configuration databases could not be found Completed 1699 Added the ability to change coordinates for point targets and ACCs Completed

CMWG Request Added verbiage to Create WDZ dialog when release range is required Completed

CMWG Request Changed Hellfire message Completed CMWG Request Added AV8B/FA18 MK-76 back in Completed CMWG Request Added A10 M117 back in Completed CMWG Request Deleted GBU35, MK36/52, MK39/55/56 Completed CMWG Request Changed MK83 live radius Completed CMWG Request Changed MK81 inert and live radius Completed

CMWG Request Enabled AC-130 40mm Completed Internal Maint Added ability to disable inert delivery option Completed Internal Maint Changed release range to 4 decimal places when nautical miles are the selected units. Completed Internal Maint Added firing point to AGM-65, AGM-114 & BGM-71 Completed Internal Maint Added feature to clear all weapon-specific entries on weapon select Completed Internal Maint Changed sorted and horizontal scroll properties on the Edit composite dialog Completed

Internal Maint Changed default units for layout view from Release Range to Altitude units Completed Internal Maint Added launch mode to AGM-114 P Completed

Internal Maint Removed the message that Installation directory name does not match the installation name on Setup Completed

Internal Maint Added function to remove single quotes and commas from installation name Completed Internal Maint Changed roll tip-off from on/off to on/off/prompt user option Completed Internal Maint Added Select WDZ to color change Completed Internal Maint Deleted unused aircraft/weapon combinations Completed Internal Maint Renamed 40 mm to 40 mm (PGU-9) Completed

Internal Maint Modified Calculate WDZ Area to display all WDZs selected Completed 1184 Changed WDZ Edit function to allow editing of Terrain Modified WDZs Completed 1612 Added the ability to change the Area of point ACCs Completed 1965 Added Wind Factor to manager, summary and layout for wind-corrected munitions Completed 624 Added scientific notation on all risk dialogs Completed 790 Added filter for max drop-down list on the Event tab Completed 826 Added nautical miles to release range Completed

CMWG Request Added 2.75 in Flare Completed CMWG Request Enabled 2.75 in M257 & M 278 Completed CMWG Request Enabled BDU38/BDU48/MK106/MK81/LGTR I Completed CMWG Request Enabled AGM-114 for Army Completed

Issue # Requirement Change Status CMWG Request Changed CV22/MV22 7.62 to sidefire capable Completed CMWG Request Added B1/GBU38 back in Completed

CMWG Request Deleted AH-1 (USAF) Completed CMWG Request Added F15 / MK106 & MK83 back in Completed

Internal Maint Changed properties on Select WDZ dialog to not allow multi-select Completed Internal Maint Added units to WDZ Summary Completed Internal Maint Moved Change WDZ Symbology from WDZ Setup to Color Change Completed Internal Maint Added an option to regenerate WDZs via the move tool Completed

Internal Maint Replaced row number with aircraft & weapon on message that WDZ could not be generated. Completed

Internal Maint Changed wind message to include knots/ft of drift for delivery Completed

Internal Maint Added feature to clear WDZ Area form at close Completed Internal Maint Added database update tool to the installer Completed Internal Maint Increased performance on WDZ load Completed Internal Maint Changed listview on Risk dialogs to use alphanumeric sorting Completed Internal Maint Added Select WDZ to Move/Rotate Tool Completed Internal Maint Modified Off-Range Risk to display all WDZs selected Completed Internal Maint Added Service name to Aircraft name Completed

1.2.9. Version 9.2.4.11.2

Table 2 - 12: Version 9.2.4.11.2 Requirements

1464 Added notation about clockwise rotation for all headings Completed

CMWG Request Added Dive Angle description for AC-130 Completed

CMWG Request Enabled GBU-24 Modes 1-4 Completed CMWG Request Disabled Pre-defined LGTR Completed

1.2.10. Version 9.2.4.15

Table 2 - 13: Version 9.2.4.15 Requirements

128 Added default layout template Completed 142 Added Wind Factor column to WDZ Manager listview. Completed

157 Modified update mag decl code to check visible features after reloading the WDZ Manager. Completed

179 Added Batch Export button to the WDZ Manager. Completed

184 Added validation code to restrict MACH values to 2 decimal places. Updated min/max validation code to handle this restriction. Completed

1366 Modified WDZ Manager Dialog so that selecting a WDZ in the list flashes the feature in the map only when one WDZ is selected. Completed

1055 Added Event Name column to WDZ Manager Completed

Issue # Requirement Change Status

1364 Added progress dialog for Import, Export, Validate All, and Create All on Batch WDZ dialog. Completed

1367 Added map layers and basic navigation to preview maps in Create WDZ wizard. Completed

1564 Added MACH to Airspeed Units comboboxes in Setup and Create WDZ wizards and the Batch WDZ dialog. Completed

1564 Added MSL and AGL radio buttons to Create WDZ wizard and Setup Wizard. Completed 1566 Populate Target elevation from the elevation layer specified in the Setup wizard. Completed 1566 Added Target Elevation textbox to Create WDZ wizard. Completed

160 Changed Move WDZ to target with different properties to use WDZ properties instead of target properties for comparison Completed

170 Add target elevation to all target forms where current elevation equals 0 Completed

857 Added reporting tool to all managers Completed 922 Changed error reporting on Batch WDZ dialog to use a scrollable textbox control Completed

CMWG Request Modified Launch Mode selection for AGM-114 K/M to Indirect only. Completed CMWG Request Modified AH-1 AGM-114 K/M to allow Direct Launch Mode Completed CMWG Request Change "CSV Export" button to "Generate Reports" Completed CMWG Request Changed the way single off-axis is displayed in the layout and summary Completed CMWG Request Added Alpha Jet and T-45 Completed

CMWG Request Disabled F-16 / 30 mm Completed Internal Maint Removed target radius from all dialogs Completed Internal Maint Display WDZ name in lieu of row number in the batch tool Completed Internal Maint Disabled string of bombs for BDU-38s Completed

1359 Added Import/Export buttons to Target and ACC Manager dialogs. Completed 1396 Added support for saving and loading release profiles on Create WDZ Wizard. Completed

147 Added WDZ_Version field Completed 147/178 Modified update mag decl code so that the WDZ version number is updated. Completed

1564 Added Altitude Type column to Batch WDZ dialog. Completed 1566 Added Target Elevation column to Batch WDZ dialog. Completed

87 Added checks for min/max Airspeed, Altitude, and Release Angle on Create WDZ dialog and Batch WDZ dialog. Completed

87 Added min/max validation for airspeed/altitude/release angle and release range to the batch tool. Completed

CMWG Request Added Griffin and AGM-114 P Completed CMWG Request Resized and realigned target editor Completed CMWG Request Change the default installation directory to match RMTK suite Completed CMWG Request Changed CV-22 & MV-22 to sidefire Completed

CMWG Request Deleted BDU-45 Completed CMWG Request Modified GAF Pre-defined WDZ parameters as requested. Completed CMWG Request Added AH-64/ 50 Cal back in Completed CMWG Request Enabled MQ-1 / Griffin and AGM-114 P Completed

Internal Maint Added Ground Range estimator for AC-130 Completed Internal Maint Added event type for AGM-114 P Completed Internal Maint Added units to target elevation Completed

Internal Maint Streamlined the batch tool load and WDZ generation routines to improve overall performance. Completed

1.2.11. Version 9.2.4.16

All requirement change requests are presented to the CMWG for approval. The CMWG rates each request on a priority scale from 1-4. All software bugs have a priority rating of one. All change requests are ranked based on the importance of the request and the level of effort of the change.

Table 2 - 14: Priority Ranking Priority Definition

1 Urgent Request – Highly recommended and approved for the next release 2 Important Request – Recommended but not urgent - Implement as soon as possible 3 Nice-to-have – Implement when all 1s and 2s have been satisfied

4 Tabled – Not needed at this time. Data may not be available, change may not be necessary after other priorities are completed, etc.

5 Not yet reviewed by the CMWG

Table 2 - 15: Version 9.2.4.16 Requirements Issue # Priority Requirement Change Status

149 1 Added Off-Range Prompt for Line and Area Targets Completed 191 2 Added feature to recalculate point risk without reselecting a map location Completed 203 2 Added Ground Range Estimator to Guns Completed

207 1 Added a progress bar to the batch tool Completed 224 2 Added units to min/max dialog messages Completed 231 Added target elevation to the batch tool Completed 475 2 Modified Move/Rotate tool to allow users to change range of run-in headings Completed

1383 2 Added function to consolidated batch tool pop-ups Completed 1396 2 Added the ability to save and load Batch tool templates Completed

1690 2 Added a min/max ground range estimation function for all the guns on the “Event” tab. Completed

1939 3 Added target coordinates to Layout view Completed

1959 2 Added database compact on batch tool initialization Completed 1960 1 Add a progress function to WDZ Manager Import Completed 1962 2 Added an “Update Directory” button to the WDZ Setup Installation Tab Completed 1966 3 Added filters to the drop-down filter list on the WDZ Manager Completed

1980 3 Added WDZ Verification information tab to the WDZ Setup to save User Approval information Completed

1980 3 Added User Approval information to the Layout view Completed 1985 1 Added Army Guns Module Completed 1985 1 Added 2.75 in (Hydra) for Army Completed 1985 1 Added AH-6/30 mm & Army Flares Completed

2062 2 Added Set WDZ Symbol Selector to the WDZ Menu Completed

2104 3 Added Airspeed, Altitude, Release Angle & Release Range to the WDZ Manager Completed

2152 2 Set MSL/AGL radio button to MSL when Altitude exceeds 18,000 ft. Completed 2202 2 Change AH-1 20mm to Sidefire capable Completed 2204 3 Removed unneeded fields from ACC Properties and Create New ACC dialogs Completed 2206 4 Delete F-16/GBU-15 & A-10/GBU-15 Completed 2223 2 Added Altitude type to Layout templates Completed

Issue # Priority Requirement Change Status

2228 3 Added function to save WDZ filters selected and reopen Manager with save parameters Completed

2231 2 Adjusted the LGTR failure ballistics to better account for release failure mode. Completed

2259 2 Changed function to display Back/Cross/Down range in both feet & meters in the layout view Completed

2269 1 Added Create Target Feature icon to the Create WDZ Target Tab. Completed

2270 2 Added Launch Mode selection in Batch tool to display based on weapon selected Completed

2283 3 Added units to the batch tool import/export functions Completed 2285 1 Add % off Range to the Calculate WDZ Area Export Completed 2288 2 Add an Update ACC Area for Pt Risk Completed

2339 1 Improved performance on WDZ Manager Load time. Completed 2358 1 Added Magnetic Declination to layout view Completed 2400 1 Set ACC Layers to load above WDZ Layers. Completed 2400 1 Moved Roll-tipoff message to the Launch Mode Selection Completed 2448 1 Remove verification message when target elevation is 0 Completed 2461 1 Added Database update function to WDZ Setup and WDZ Manager Init Completed

2461 1 Added function to WDZ Setup to update source data for tables and feature classes to current location Completed

2461 1 Create New Installation now checks for conflicting layers and tables on the map and appends “_WDZ” to the installation name if there is a conflict layer on the map

Completed

2482 1 Implemented GBU-54 Laser JDAM Completed 2510 1 Enabled MH-60/2.75 in Hydra(70) Completed

2581 / 2582 / 2590 1 Changed Name of AGM-114 K/M to AGM-114 K-N Completed

CMWG

Request 1 Added Paveway IV Module Completed

CMWG

Request 1 Added O-2 / 2.75 in & 7.62 mm Completed

CMWG

Request 1 Added Brass overboard option for Army 20 & 30 mm Completed

CMWG

Request 1 Added MC-130 30mm Completed

CMWG

Request 1 Change the Event flag on fixed guns to “Guns – Strafe Only” Completed

CMWG

Request 1 Enabled AH-6, CH-47 & UH-60 Completed

CMWG

Request 1 Disabled AH-6 (USAF), OH-58 (USAF) & HH-53 (USAF) Completed

Internal Maint 1 Added RangeName to Off-range risk dialog Completed

Internal Maint 1 Added code to remove single quotes and commas from all fields and removed validation tools Completed

Internal Maint 1 Changed the batch tool to allow batch files from previous versions Completed

Internal Maint 1 Added ballistic preview when engineering sidefire gun WDZs on the “Orientation” tab Completed

Internal Maint 1 Modified Area F message for Hellfire Completed Internal Maint 1 Changed “GDA + Bank” label to only display for sidefire guns Completed

149 1 Added Off-Range Prompt for Line and Area Targets Completed

1.2.12. Version 9.2.4.16.1

Table 2 - 16: Version 9.2.4.16.1 Requirements

2540 1 Changed GAF GBU-24 to GBU-24 Mode 1 and 2 Completed

2585 1 Added Inert option for MC-130 30mm Completed

CMWG

Request 1 Added max-energy 5000 ft. buffer to Paveway IV Completed

CMWG

Request 1 Removed OH-6 & UH-60 for US Army Completed

CMWG

Request 1 Removed US Army (AH-64 / 20mm, MH-60L / 50Cal & 30mm Flex, AH-6 / 30 mm, 50 Cal DG, Tow & TOW2B, OH-58 / 50Cal DG & CH-47 / 50Cal) Completed

Internal Maint 1 Removed C++ redistribution patch requirement Completed

Internal Maint. 1 Added AH-6 / 7.62 mm back in Completed

1.2.13. Version 9.3.1.2.1, 10.0.0.4.2 & 10.1.0.0.1

Table 2 - 17: Version 9.3.1.2.1, 10.0.0.4.2 & 10.1.0.0.1 Requirements

1956 1 On the ACC Properties GUI display a message to the user that all risk assumes the ACC is "Unprotected Troops in the open". Completed

2366 1 Add Vertical Hazard to layout view Completed

2371 1 Make WDZs visible when composite is uncombined and not visible when composite is created (Same rules apply to edit composite) Completed

2372 1 Do not require users to deselect WDZs that cannot be modified by terrain. Completed 2375/2338 1 Add conflict layers Completed

2380 1 Change the drop-down list for Airspeed, Altitude & Release Range on the event tab and the batch tool based on the selected units. Completed

2398 1 When WDZs are combined the individual WDZs should be removed from view and when a composite is uncombined the individual WDZs should be made visible.

Completed

2411 1

Menu changes - Change "Create Target Point" to open the "Create New Target Point" dialog. Change "Create ACC Point" to open the "Create ACC Point" dialog. Change "Create Target" Menu title to "Create Target Area".

Change "Create ACC" Menu title to "Create ACC Area". Change “Set WDZ Symbol Levels” title to “Restack WDZs”.

Completed

2414 1 Modified AV-8B to mirror F/A-18 pending release of corrected JMEMs data Completed 2417/2287 1 Pull ACC elevation from the map elevation layer. Completed

2423 1 Catch the error thrown from Modify by Terrain when a WDZ extends beyond the bounds of the elevation layer. Display the appropriate message to the user and do not allow Terrain Modification.

Completed

2430 1 Batch Tool process takes too long - delay adding WDZs to the map until the batch is Completed Completed

2450 1 Move Tool does not update WDZ to new target properties when moved to a new target. Completed

2452 1 Place Batch Tool validation dialog on top and centered on the batch tool dialog Completed

2454 1 Color change should move WDZ to the top of the stack. Completed

Issue # Priority Requirement Change Status

2457 1

List all composites the WDZ is included in in the WDZ manager and only clear the composite flag when the WDZ is no longer contained in any composites.

Suggestion: Include the wdz_id for the Composite in the WDZ List field of the WDZ to save time looking these up with each load.

Completed

2459 1 Add ACC Area and buffer values to reporting functions & ACC Manager Completed

2472 1 All features should be forward compatible. All files saved in previous versions should work in a newer version. i.e. batch files, saved profiles, database exports, etc.

Bug Fix

2485 1 Add Hellfire prohibited zones Completed 2497 1 Add Firing Point polygon class Completed 2498 2 Add Watermark to layout view Completed

2507 1 Add Ground Range Estimator to all GBUs Completed

2521 1 Target Import only checks the target_Id against the targets that were created before…