A02 Statement of Work CAT Command Center.pdf

Specifications for

CAT COMMAND TRAILER

1.0 GENERAL

This purchase description establishes the minimum technical requirements for one (1) Commercial Cat Command Trailer for the U.S. Army Aberdeen Test Center. The system shall enable conversion of a man-operated forestry mulcher to remote operation and is intended for field use.

2.0 APPLICABLE DOCUMENTS

The following documents form a part of this purchase description:

• Operator's Manuals (complete set)

• OEM Equipment Certifications of Warranty

3.0 REQUIREMENTS

3.1 System Description

The Cat Command Trailer shall consist of a CAT Command Center, trailer, camera array, CPU, WiFi capability, power converters, and antennas.

3.1.1 CAT Command Center

Component Specification Command Station CAT 576-6000 SEA Station CAT 599-4855 Display Arm CAT 580-5669 Pedestal Set CAT 576-6024 TV’s and Monitors WCA Kit, CAT Command Compliant MAST Power telescoping antenna mast Radio (2) Cisco IW3702 Radio Antenna (2) Communications Antenna Camera Site Camera

3.2 Trailer Construction and Frame

Component Specification Frame Construction All tube construction Axle Spacing 5" spread axle, standard ground clearance

Axle 5,200 lb torsion with EZ Lube hubs, electric brakes Coupler A-frame, 2-5/16", 10,000 lb capacity Tongue Jack Side wind, drop leg, 7,000 lb Stabilizer Jacks Scissor type, 24", 5,000 lb Frame Protection Bogey wheels

3.2.1 Trailer Floor and Roof Structure

Floor Cross Members 16" O/C, 8.5'W, aluminum

Roof Cross Members 16" O/C, 1" x 3", 8.5'W, aluminum Floor Design Flat Front Design Flat, aluminum, 8.5'W Interior Wheel Box Smooth aluminum, spread axle, tandem

3.2.2 Trailer Interior Configuration

Interior Height 7.0' Interior Ceiling Screwless aluminum Interior Walls Screwless aluminum over 3/8" plywood (6.5'–8.0' range) Flooring TPO gray coin Ceiling Insulation Fiberglass batten, R-11 Wall Insulation Closed cell, R-13 (6.5'–8.0' range)

3.2.3 Exterior Features

Tongue Cover ATP Exterior Aluminum Thickness 0.030 (6.5'–8.0' range)

Fenderettes Aluminum, polished Gravel Guard ATP, 24" with J-rail Roof One-piece aluminum

Front Trim Cast corners, polished; top radius, stainless steel; verticals, stainless steel

Rear Vertical Trim Color matched Rear Header Trim Color matched Upper Rub Rail Aluminum, 4" Lower Rub Rail Aluminum, 4" DOT Reflectors Installed

3.2.4 Doors and Access

Entrance Door 405 Series, 32" x 78", flush lock Entrance Door Latch Bar lock, offset, aluminum Cam Bar/Bar Lock Hasp Stainless steel (for ramp door) Step Slide in/out aluminum, 32" Baggage Door 405 Series, 46" x 22", baggage latch Fuel Door Cast aluminum, lockable

3.2.5 Ventilation

Vent System Two-way, Salem Roof Vent Manual, MaxxAir Mini

3.2.6 Electrical System

Truck Plug 7-way, bumper pull Breaker Box 50 amp, 120V only Converter 60 amp, 12V Fuse Panel Inteli-Power unit Power Inlet Motorbase 50A with 25' shore cord, black Transfer Switch Automatic, 50A Battery 100AH lithium, basic Power Cut-off Switch Manual, 12V

3.2.7 Interior and Exterior Lighting

Component Specification Lower Amber Clearance Lights LED, 12V Upper Amber Clearance Lights LED, 12V Lower Red Clearance Lights LED, 12V Upper Red Clearance Lights LED, 12V Taillights Slimline LED, 12V, red License Plate Light 12V Scene Lights LED high output, 12V, non-recessed, 14" x 2.5", black bezel Loading Lights LED, 12V, exterior Rectangular Light LED, 14", 12V, surface mount

3.2.8 Switches and Receptacles

Interior Receptacles 120V, 15A, black Exterior Receptacles 120V, 15A, GFI protected, black Wall Switch (Scene) On/off, 12V, black Wall Switch (Loading) On/off, 12V, black Wall Switch (Auxiliary) On/off, 12V, black Awning Switch 12V 3-Way Wall Switch 12V, black

3.2.9 Climate Control

Air Conditioner 15,000 BTU, low profile, 10.5" height, black, with heat pump A/C Easy Start Included

3.2.10 Power Generation

Generator NPS 6000K Yamaha with 24-gallon fuel tank Generator Compartment Tongue mounted, ATP

3.2.11 Wall Structure (Additional)

Wall Cross Members (CS) 16" O/C, 2" x 2", 7.0'H, aluminum Wall Cross Members (RS) 16" O/C, 2" x 2", 7.0'H, aluminum

3.2.12 Mast Preparation

Mast Backer Aluminum

4.0 QUALITY ASSURANCE

All components shall be covered by a full one-year manufacturer's warranty.

5.0 CONTRACTOR SERVICES

The contractor shall provide:

• Installation of all equipment

• Operator training

6.0 DELIVERY

Delivery Address:

U.S. Army Aberdeen Test Center 6850 Lanyard Road, Building 358 Aberdeen Proving Ground, MD 21005-5059 Point of Contact:

Ben Gallardy Email: benjamin.c.gallardy.civ@army.mil Telephone: (410) 278-5603

7.0 NOTES

• All electrical components shall operate on 12V DC unless otherwise specified as 120V

AC

• Trailer shall be suitable for continuous operation in all weather conditions

• Equipment shall be Commercial Off-The-Shelf (COTS) or non-developmental items where possible mailto:benjamin.c.gallardy.civ@army.mil