lpp-square-tapered-steel-external-hinged.pdf

Engineered & Manufactured In The U

SA

Rev. V05092018 This specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without notice.

Project Name

Catalog #

Pole Type

Product Overview

• Pole Shaft - The pole shaft for 4.00" non-tapered square poles is fabricated from hot rolled commercial quality carbon steel of one-piece construction with a minimum yield strength of 55,000 psi. The pole shaft for all other sizes conforms to ASTM A595 Grade A or A572 Grade 55 with a constant linear taper of 0.11 in/ft.

• Pole Top - Pole is provided with either a tenon top or drilled for a fixture mounting. A removable pole cap is provided for drilled poles. Consult the luminaire manufacturer for correct tenon size or drill pattern.

Other pole top options include pole cap only or plain top which is typical when the pole top diameter matches the necessary slip fit dimensions.

• Hinge - The external hinge includes a stainless steel pin. A flexible guide is provided for wiring protection through the hinge area.

• Shroud - The shroud is fabricated from weldable grade hot rolled commercial quality carbon steel with a minimum yield strength of 45,000 psi. It is a one piece formed channel which conforms to the pole shaft taper. The shroud is secured by a threaded stud and nut with provisions for a padlock to prevent accidental or unauthorized lowering.

• Winch - A removable winch is available for raising and lowering the pole.

• Hand Hole - A reinforced handhole with grounding provision is provided at 1'-6" from the base end of the pole assembly. Each handhole includes a cover and the cover attachment hardware. Poles with a 4.00" base square are supplied with a 3" X 5" rectangular handhole. All other pole assemblies are provided with a 4" X 6.5" ovalized handhole. Handhole dimensions are nominal.

• Full Base Cover - Optional two-piece full base cover is fabricated from ABS plastic. The manufacturer reserves the right to provide a two-piece steel full base cover on some applications depending upon the finish requirement and/or pole base square.

• Anchor Bolts - Anchor bolts conform to ASTM F1554 Grade 55 and are provided with two hex nuts and two flat washers. Bolts have an “L” bend on one end and are galvanized a minimum of 12" on the threaded end.

• Hardware - All structural fasteners are galvanized high strength carbon steel. All non-structural fasteners are galvanized or zinc-plated carbon steel or stainless steel.

• Finish - Standard finishes are either Galvanized or Finish Painted. Additional finish options including Finish Paint over Galvanizing are available upon request.

• Design Criteria - Standard EPA (Effective Projected Area) and weight values are based on Standard Commercial Criteria (with 1.3 gust factor) for top mounted fixtures only. Consult the factory on loading criteria for side mounted luminaires and/or brackets. Satisfactory performance of light poles is dependent upon the pole being properly attached to a supporting foundation of adequate design.

Square Tapered Steel External Hinged Light Poles, Anchor Base

206 W. McWilliams St.

Suite 101 Fond du Lac, WI 54935

888-791-1463 quotes@lightpolesplus.com LightPolesPlus.com https://lightpolesplus.com

This specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without notice.

Engineered & Manufactured In The U

SA

Rev. V05092018

Designation & Dimensional Information

EPA Load Information

1. The total combined EPA and weight of all fixtures, brackets and attachments mounting to a light pole cannot exceed the EPA and weight rating for a specified pole.

2. Maximum EPA (Effective Projected Area) and weight values are based on top mounted luminaires and/or brackets having a centroid 2’-6” above the Nominal Mounting Height. Variations from sizes above are available upon inquiry at the factory.

3. Satisfactory performance of light poles is dependent upon the pole being properly attached to a supporting foundation of adequate design.

CAUTION: To prevent damage to the pole, the winch cable must be kept taut when raising or lowering the pole.

CAUTION: To properly operate the hinge mechanism, a minimum pole top load of 50 lbs. is required.

Note: Additional sizes and configurations are available upon request.

"+" Indicates a vibration dampener is standard

BASE MODEL

80 MPH w/1.3 GUST 90 MPH w/1.3 GUST 100 MPH w/1.3 GUST

MAX EPA

(SQFT)

MAX WEIGHT

(LBS)

MAX EPA

(SQFT)

MAX WEIGHT

(LBS)

MAX EPA

(SQFT)

MAX WEIGHT

(LBS)

VS-SSEH-20-4040-07-AB-FP 11.6 217 8.5 217 6.2 217

VS-SSEH-25-4040-07-AB-FP 7.1 160 4.8 160 3.1 160

VS-SSEH-25-6437-11-AB-FP 18 254 13 254 9.3 254

VS-SSEH-30-4040-07-AB-FP 4 120 2.1 120 0.8 120

VS-SSEH-30-6431-11-AB-FP 12.5 230 8.3 230 5.1 230

VS-SSEH-35-7133-07-AB-FP 22 155 16.9 155 12.1 155

VS-SSEH-35-7233-11-AB-FP 7.1 160 3.2 160 N/A N/A

VS-SSEH-39-7129-07-AB-FP 19.5 110 13.5 110 9.2 110

VS-SSEH-39-7229-11-AB-FP 4.3 135 N/A N/A N/A N/A

BASE MODEL

POLE DIMENSIONS BASE PLATE ANCHOR BOLTS

WINCHNOMINAL

MOUNTING

HEIGHT

TOP

SQ

(IN)

BASE

SQ

(IN)

WALL

THK

(GA)

STRUCTURE

WEIGHT

(LBS)

OPERATIONAL

RADIUS

BOLT-

CIRCLE

DIA (IN)

SQ (IN) x

THICK (IN)

DIA x LENGTH x

HOOK (IN)

PROJECTION

(IN)

VS-SSEH-20-4040-07-AB-FP 20'-0" 4 4 7 300 9'-3" 8.5 - 10 9.75 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 M180A VS-SSEH-25-4040-07-AB-FP 25'-0" 4 4 7 370 11'-9" 8.5 - 10 9.75 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 M180A VS-SSEH-25-6437-11-AB-FP 25'-0" 3.7 6.4 11 355 10'-10" 12.5 11.88 x 0.875 1.00 x 36.00 x 4.00 3.88 - 4.38 M136 VS-SSEH-30-4040-07-AB-FP 30'-0" 4 4 7 435 14'-3" 8.5 - 10 9.75 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 M180A VS-SSEH-30-6431-11-AB-FP 30'-0" 3.1 6.4 11 440 14' 12.5 11.88 x 0.875 1.00 x 36.00 x 4.00 3.88 - 4.38 M136 VS-SSEH-35-7133-07-AB-FP 35'-0" 3.3 7.1 7 700 17' 13.5 12.63 x 1.25 1.00 x 36.00 x 4.00 4.25 - 4.75 M135 VS-SSEH-35-7233-11-AB-FP 35'-0" 3.3 7.2 11 540 17' 13.5 12.63 x 0.875 1.00 x 36.00 x 4.00 3.88 - 4.38 M135 VS-SSEH-39-7129-07-AB-FP 39'-0" 2.9 7.1 7 740 19'-3" 13.5 12.63 x 1.25 1.00 x 36.00 x 4.00 4.25 - 4.75 M135 VS-SSEH-39-7229-11-AB-FP 39'-0" 2.9 7.2 11 555 19'-3" 13.5 12.63 x 0.875 1.00 x 36.00 x 4.00 3.88 - 4.38 M135

206 W. McWilliams St.

Suite 101 Fond du Lac, WI 54935

888-791-1463 quotes@lightpolesplus.com LightPolesPlus.com https://lightpolesplus.com h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight

Engineered & Manufactured In The U

SA

Rev. V05092018206 W. McWilliams St.

Suite 101 Fond du Lac, WI 54935

888-791-1463 quotes@lightpolesplus.com LightPolesPlus.com https://lightpolesplus.com

Ordering Information

Options & Accessories

Engineered & Manufactured In The U

SA

Rev. V05092018

Note: Please consult factory or your sales representative to verify options and accessories will work with your light pole part number.

* See previous pages for base model configurations.

Consult factory or your sales rep for deviations from base models.

Additional sizes and configurations available upon request.

Thickness*

07 = 7ga

11 = 11ga

Top OD*

29 = 2.9”

31 = 3.1”

33 = 3.3”

37 = 3.7”

40 = 4”

Base OD*

40 = 4”

64 = 6.4”

71 = 7.1”

72 = 7.2”

Ex. VS-SSEH-20-4040-07-AB-FP-DB-D1

Description

BCSPCL =

Special Base Plate to Match Existing Bolt Circle (May Add 2 Weeks to Production Lead Time, May Require Special Base Cover)

VDA = Internal Vibration Dampener, Factory Installed

VDF = Internal Vibration Dampener, Field Installable

FBCS = Steel Full Base Cover

FBCP = ABS Plastic Full Base Cover

Description

ULHH = UL Compliant Hand Hole

NECHH = NEC 410.30 Compliant Hand Hole & Cover

EHH =

Additional Hand Hole Opening w/ Cover Assembly (Specify Pole Height & Orientation)

FST = Festoon Provision, Electrical by Others (Specify Pole Height & Orientation)

CPL = NPT Pipe Coupling (Specify Pole Height, Orientation & NPT Size)

PXDX = Side Drill + Tenon w/ Additional Hand Hole (Specify Tenon OD & Length)

Anchor Bolts

AB =

Includes Anchor Bolts

LAB =

Less Anchor Bolts

Designation

VS-SSEH =

Square Tapered Steel External Hinged Anchor Base

Length*

20 to 39

Fixture Mounting

Drill Mounting (includes cap)

D1 = Single

D2 = 2@180 deg.

D4 = 4@90 deg.

D5 = 2@90 deg.

D6 = 3@90 deg.

Tenon Mounting

P1 = 4” OD x 5” Long Tenon

P2 = 2.38” OD x 4” Long Tenon

P3 = 3.50” OD x 6” Long Tenon

P4 = 4” OD x 6” Long Tenon

P5 = 2.88” OD x 4” Long Tenon

P6 = 2.88” OD x 5” Long Tenon

P7 = 2.38” OD x 5” Long Tenon

PQ = 2.38” OD x 12” Long Tenon

PD = 3” OD x 3” Long Tenon

P9 = Custom Size Tenon

Other Options

PC = Cap Only, No Side Drilling

PL = Open Top, No Cap or Side Drilling

Finish Type

GV = Galvanzied Only (No Paint)

FP = Finish Painted

FPGV =

Finish Paint over Galvanizing

Description

STAMP = Engineering Services, Signed & Sealed Calcs

STAMPCA = Engineering Services, CA Signed & Sealed Calcs

PRE075 = Pre-Ship Anchor Bolts - 0.75" x 17" x 3"

PRE100 = Pre-Ship Anchor Bolts - 1.0" x 36" x 4"

M135 = Pole Winch (Refer to Spec table for proper winch)

M136 = Pole Winch (Refer to Spec table for proper winch)

M180A = Pole Winch (Refer to Spec table for proper winch)

Painted Color

DB = Dark Bronze

MB = Medium Bronze

LG = Light Gray

DG = Dark Green

HG = Hunter Green

SG = Slate Gray

BK = Black

WH = White

SL = Silver

NA =

Natural Alum.

Painted

SC = Custom

206 W. McWilliams St.

Suite 101 Fond du Lac, WI 54935

888-791-1463 quotes@lightpolesplus.com LightPolesPlus.com https://lightpolesplus.com h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight h6tscmjf Highlight