W912BU-16-B-0004_Specs-AM1.pdf

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods:

(a) By completing items 8 and 15, and returning or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment your desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. CONTRACT ID CODE

2. AMENDMENT/MODIFICATION NO. 3. EFFECTIVE DATE 4. REQUISITION/PURCHASE REQ. NO. 5. PROJECT NO. (If applicable)

7. ADMINISTERED BY (If other than Item 6) CODE

STANDARD FORM 30 (REV. 10-83)

Prescribed by GSA FAR (48 CFR) 53.243

FACILITY CODE

10A. MODIFICATION OF CONTRACT/ORDER NO.

10B. DATED (SEE ITEM 13)

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers is extended, is not extended.

12. ACCOUNTING AND APPROPRIATION DATA (If required) copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

13. THIS ITEM ONLY APPLIES TO MODIFICATION OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

CHECK ONE A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT ORDER NO.

IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15C. DATE SIGNED

15A. NAME AND TITLE OF SIGNER (Type or print)

16C. DATE SIGNED

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

PAGE OF PAGES

6. ISSUED BY CODE

8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, State and ZIP Code) (X)

CODE

15B. CONTRACTOR/OFFEROR

(Signature of person authorized to sign)

16B. UNITED STATES OF AMERICA

(Signature of Contracting Officer)

NSN 7540-01-152-8070

Previous edition unusable

W912BU

FY 16 Periodic Nourishment, Townsend Inlet to Cape May Inlet Storm Damage Reduction Proj, Avalon & Stone Harbor, Cape May County, NJ

THIS AMENDMENT DOES NOT EXTEND THE 9 AUGUST 2016 BID OPENING DATE AT 11:00 A.M.

E5CTCSGF

US ARMY ENGINEER DISTRICT, PHILADELPHIA

WANAMAKER BUILDING, 100 PENN SQUARE EAST

PHILADELPHIA, PENNSYLVANIA 19107-3390

US ARMY ENGINEER DISTRICT, PHILADELPHIA

POC: SANDI FLETCHER

WANAMAKER BUILDING, 100 PENN SQUARE EAST

PHILADELPHIA, PENNSYLVANIA 19107-3390

9A. AMENDMENT OF SOLICITATION

NO.

W912BU-16-B-0004

07/27/2016

9B. DATED (SEE ITEM 11)

07/7/2016

Continued:

This page was intentionally left blank for duplex printing.

Amendment No. 0001

IFB W912BU-16-B-0004

14. DESCRIPTION OF AMENDMENT (continued)

a. REQUESTS FOR INFORMATION (RFI) WITH RESPONSES: RFI’s with responses, annotated Amendment No. 0001, are attached to this amendment.

b. TECHNICAL SPECIFICATIONS:

(1) SECTION 01 35 30 – MUNITIONS AND EXPLOSIVES OF CONCERN (MEC)

CONSTRUCTION SUPPORT: Please add new pages 01 35 30-7 to 01 35 30-49 in their entirety, annotated Amendment No. 0001, attached hereto.

c. Please indicate receipt of this amendment on Standard Form 1442

(SOLICITATION, OFFER, AND AWARD) as Amendment No. 0001. Failure to acknowledge all amendments may be cause for rejection of the bid.

RFI#

Dwg Sheet/ Spec Section Request for Information Response

Will the contractor be permitted to lay pipe on shore between the two beaches at Stone Harbor (stations 314+49 to 335+00)? Yes, as the referenced stations are within the CWL.

Please clarify if the “maximum allowable depth” for each borrow area is the maximum removal depth based on AD survey or the maximum disturbance depth.

Maximum allowable depth is the maximum removal depth based on AD survey.

Section 00 70 00, paragraph 52.211-10

Section 00 70 00, paragraph 52.211-10 states “The Contracting Officer has the right to exercise any or all of the options within 7 calendar days after the approval by the Government of the Pre-Condition Surveys.” Please confirm that the term “approval” is triggered as the Governments acknowledgement of the submission of the Pre-Conditional Surveys submittal. Or please clarify this timeframe.

NO, “approval” is not contractually triggered by the Government's acknowledgement of a submission of the Pre-Conditional Surveys submittal(s). The 7 calendar day period to exercise an option does not begin until, "...after the approval by the Government of the Pre-Condition Surveys." Reference Section 01 71 23; Part 3.6 for Pre- Placement and Post Placement Condition surveys; and

3.6.2 for Completion time requirements.

Section 32 15 00 -

Para. 2.5

Section 321500 2.5, states that the split rail fence is to made of No 1 cedar.

Historically the split rail fence has been pressure treated southern yellow pine or poplar and locust. Please clarify. Split rail fence shall be No. 1 cedar.

REQUESTS FOR INFORMATION with RESPONSES

Solicitation No. W912BU-16-B-0004

Technical Paper 18 1 September 2015

DDESB

Minimum Qualifications for Personnel Conducting Munitions and Explosives of

Concern-Related Activities

Department of Defense Explosives Safety Board

Alexandria, Virginia

Distribution authorized to U.S. Government agencies and their contractors; administrative/operational use; 11 May 2015. Other requests for this document must be referred to the Department of Defense Explosives Safety Board.

Amendment No. 0001

Section 01 35 30 Page 7

DDESB TP 18, 1 September 2015

This page intentionally left blank

Amendment No. 0001

Section 01 35 30 Page 8

Section 01 35 30 Page 9

Table of Contents

TABLE OF CONTENTS

CHAPTER 1. INTRODUCTION

1.1. General

1.2. Applicability

CHAPTER 2. MEC-RELATED ACTIVITIES PERSONNEL – POSITION TITLES,

DUTIES, AND RESPONSIBILITIES

2.1. General

2.2. Duties and Responsibilities

a. MEC-Related Activities Support

b. UXOT

c. UXOQP

d. Dive-Qualified Personnel

APPENDIX. DEPARTMENT OF LABOR, SERVICE CONTRACT ACT DIRECTORY

OF OCCUPATIONS - UXO POSITION DESCRIPTIONS

CHAPTER 3. UXO-TI TRAINING STANDARDS

3.1. Minimum Training Standards for a UXO-TI

3.2. Curriculum and Training Objectives for a UXO-TI

a. Munitions Responses to MEC

b. Operational Range Clearance Activities and Similar Operations

c. Measurements and Mathematical Computations

d. Electricity

e. Physics

f. Military Munitions – Explosives and Explosive Effects

g. Military Munitions – Fuze Functioning

h. Explosives Safety Precautions

i. Military Munitions Identification

j. Underwater Munitions Identification

k. Detection Equipment

l. PPE

m. Demolition Materials

n. Firing Systems

o. Destruction and Demilitarization

p. Storage, Handling, and Transportation of Explosives (Military and Commercial)

q. Skills Requirements

CHAPTER 4. MINIMUM QUALIFICATION STANDARDS

Amendment No. 0001

Section 01 35 30 Page 10

Table of Contents

GLOSSARY

G.1. Acronyms G.2. Definitions

REFERENCES

TABLES

4.1. Minimum Qualifications for UXOQP

4.2. Minimum Qualifications for UXOT

4.3. Minimum Qualifications for SP and SW

Amendment No. 0001

Section 01 35 30 Page 11

Chapter 1: Introduction 1

This page intentionally left blank

Amendment No. 0001

Section 01 35 30 Page 12

Chapter 1: Introduction 2

CHAPTER 1

INTRODUCTION

1.1. GENERAL

a. This technical paper (TP) provides minimum qualification standards, established by the DoD Explosives Safety Board (DDESB), for personnel who:

(1) Support munitions and explosives of concern (MEC)-related activities:

(a) Support workers (SW).

(b) Sweep personnel (SP).

(2) Conduct or supervise MEC-related activities:

(a) Unexploded ordnance technicians (UXOTs).

(b) UXO qualified personnel (UXOQP).

b. MEC-related activities include, but may not be limited to:

(1) Munitions responses to MEC.

(2) Operational range clearance-related activities.

(3) Similar operations that involve the intentional physical contact with MEC including:

(a) Chemical military munitions and chemical agents (CAs) in other than a munitions configuration (collectively referred to as “chemical warfare materiel (CWM)”).

(b) Ground-disturbing or other intrusive activities in areas known or suspected to contain MEC.

c. During MEC-related activities, personnel may be exposed to explosive or CA hazards (collectively referred to as “explosive hazards”) posed by MEC (e.g., UXO, discarded military munitions (DMM)) and associated material potentially presenting an explosive hazard (MPPEH).

Collectively, these activities and operations are referred as “MEC-related activities.”

d. Personnel must, commensurate with their duties, meet the minimum qualification standards of this TP when:

(1) Performing or supervising operations when intentional physical contact with MEC is planned or will occur.

Amendment No. 0001

Section 01 35 30 Page 13

Chapter 1: Introduction 3

(2) Conducting ground-disturbing or other intrusive activities in areas known or suspected to contain MEC.

e. Personnel who support, conduct, or supervise MEC-related activities who do not meet the minimum qualification standards of Tables 4.1, 4.2, or 4.3 must not have direct contact with MEC or MPPEH encountered during MEC-related activities until the material has been evaluated and determined not to pose an explosive hazard. SWs (e.g., geophysicists, vehicle operators, guards):

(1) Must be provided explosives safety education (e.g., DoD recognize, retreat, report (3Rs) explosives safety education training) before being allowed in areas known or suspected to contain MEC.

(2) May require escort by a UXOT (see Paragraph 2.2.b.(1)(k)) or UXOQP.

1.2. APPLICABILITY

a. These requirements apply to:

(1) DoD personnel that perform MEC-related activities.

(2) Contractors performing MEC-related activities under:

(a) DoD contracts.

(b) State and other federal contracts, when the application of these requirements were stipulated or agreed on in property transfer documents (e.g., Finding of Suitability for Early Transfer) and/or agreements (e.g., Environmental Services Cooperative Agreements) between DoD and a State or other federal agency.

(3) DoD personnel or contractors conduct ground-disturbing or other intrusive activities funded by the DoD in areas known or suspected to contain MEC, and activities involving the intentional physical contact with MEC, except as specified in Paragraph 1.2.b.

b. These requirements do not apply to:

(1) DoD explosive ordnance disposal (EOD) operations.

(2) Personnel performing duties directly related to quality assurance (QA) surveillance testing or research, development, test and evaluation (RDT&E).

(3) Explosives workers such as personnel involved in the decontamination or demolition of explosives-contaminated buildings or infrastructure.

Amendment No. 0001

Section 01 35 30 Page 14

Chapter 1: Introduction 4

(4) Operational and former ranges for which it is confirmed based on physical or historical evidence that the only munitions-related activities that occurred on the range were ones that involved live-fire training or testing with small arms ammunition. However, personnel working on such ranges will at a minimum be provided explosives safety education (e.g., DoD recognize, retreat, report (3Rs) explosives safety education training), which must include recognition of military munitions.

(5) Other entities (e.g., commercial developers, contractors) performing MEC-related activities under contract with a State or other federal entities. However, the DDESB recommends the State or federal entity require their application.

Amendment No. 0001

Section 01 35 30 Page 15

Chapter 2: MEC-Related Activities Personnel 5

This page intentionally left blank

Amendment No. 0001

Section 01 35 30 Page 16

Chapter 2: MEC-Related Activities Personnel 6

CHAPTER 2

MEC-RELATED ACTIVITIES PERSONNEL –

POSITION TITLES, DUTIES AND RESPONSIBILITIES

2.1. GENERAL

a. Training levels and work experience of the following personnel must be documented and verifiable:

(1) MEC-Related Activities Support Personnel

(a) SW

(b) SP (see 29495l in the appendix to this chapter)

(2) UXOT

(a) UXO-Technician I (UXO-TI) (see 29491 in the appendix to this chapter)

(b) UXO-Technician II (UXO-TII) (by definition are also UXOQP) (see 29492 in the appendix to this chapter)

(c) UXO-Technician III (UXO-TIII) (by definition are also UXOQP) (see 29493 in the appendix to this chapter)

(3) UXOQP

(a) UXO Quality Control Specialist (UXOQCS)

(b) UXO Safety Officer (UXOSO)

(c) Senior UXO Supervisor (SUXOS)

(4) Dive Qualified Personnel

b. DoD activities and DoD contractors performing MEC-related activities are responsible for ensuring personnel employed meet the qualifications specified in this TP.

c. Personnel assigned to support MEC-related activities that are only responsible for supervising (e.g., dive master) or supporting (e.g., dive tender) dive operations from the surface are not required to be a UXOT or meet the criteria of UXOQP. When performing MEC-related activities, such personnel must also meet the qualification criteria for the task performed.

Amendment No. 0001

Section 01 35 30 Page 17

Chapter 2: MEC-Related Activities Personnel 7

d. Under certain circumstances, the duties of a UXOSO and UXOQCS may be filled by a single individual who meets the training and experience requirements for both positions. If not explicitly specified in the contracting documents or applicable Service guidance, site-specific decisions allowing performance of the duties by a single individual will be provided in writing by the government contracting officer’s representative on advice of government explosives safety personnel and in coordination with the contractor.

e. UXOTs and UXOQP must meet the applicable requirements of 18 United States Code (U.S.C.) 842 as amended by the Bureau of Alcohol, Tobacco, Firearms and Explosives in 27 Code of Federal Regulations (CFR) 555.26 and State requirements. Personnel who do not meet these requirements will not be provided access to explosives.

f. Personnel supporting or conducting MEC-related activities may be required to possess specific or specialized licenses (e.g., a commercial or specialized vehicle driver’s license, state blasters license), hazardous material endorsements, or be included in a medical monitoring program. (See 29 CFR 1910.120.)

g. Personnel who are working at a hazardous waste site may require successful completion of 40 hours of hazardous waste operations and emergency response (HAZWOPER) training per

29 CFR 1910.120.

2.2. DUTIES AND RESPONSIBILITIES. This chapter identifies and describes positions by title and outlines the duties and responsibilities of each position. Although this chapter addresses some qualifications, Chapters 3 and 4 present detailed qualifications and training requirements.

a. MEC-Related Activities Support. Personnel who are not UXOTs or UXOQP, but support MEC-related activities, perform a variety of tasks (e.g., brush-cutting, operating heavy equipment, surveying, site security, dive tenders) required to support the safe conduct of MEC-related activities.

(1) SW

(a). Must be provided general and site-specific training. At a minimum, this must include:

1. General and site-specific safety. Such training includes, but may not be limited to the proper use of equipment and personal protective equipment (PPE); physical, biological, and chemical hazards; and the potential hazards associated with the tasks they are to perform.

2. Explosives safety training. Recognition of munitions; raw, possibly weathered explosives (e.g., trinitrotoluene (TNT), propellants); and chemical agent identification sets (CAIS) and the actions that should be taken should a suspect munition be encountered (e.g., 3Rs).

Amendment No. 0001

Section 01 35 30 Page 18

Chapter 2: MEC-Related Activities Personnel 8

(b) SW will:

1. Not conduct activities (e.g., ground disturbing) that could result in physical contact with MEC, including CWM, CAIS, or MPPEH unless protected or escorted.

2. When determined necessary by a risk assessment, be shielded from the potential explosive hazards associated with MEC known or suspected to be present within the site (e.g., heavy equipment operators).

3. Be escorted by a UXOT (see Paragraph 2.2.b.(1)(k)) or UXOQP within areas known or suspected to contain MEC, when determined necessary by a risk assessment that considers the support or tasks they are to perform. Escorts will help ensure MEC on the surface, and subsurface anomalies are avoided. Support activities performed by SW who may require escort include:

a. Conducting geophysical surveys and similar activities.

b. Clearing vegetation from areas where surface MEC is known or suspected to be present.

c. Operating heavy equipment.

d. Performing site or area security functions requiring access to areas where surface MEC is known or suspected to be present or MEC-related operations are being conducted.

(2) SP. The SP must:

(a) Assist UXOT and UXOQP in the performance of MEC-related activities but are not involved in explosive operations.

(b) Provide general and site-specific training. At a minimum, this must include:

1. General and site-specific safety. Such training includes, but may not be limited to the proper use of equipment and PPE; physical, biological, and chemical hazards; and the potential hazards associated with the tasks they are to perform.

2. Explosives safety training. Recognition of military munitions; raw, potentially weathered explosives (e.g., TNT, propellants); and CAIS and actions that should be taken should a munition or suspect munition be encountered (e.g., 3Rs).

(c) Not be allowed to conduct activities that could result in physical contact with MEC, including CWM or CAIS; material documented as an explosive hazard (MDEH); and MPPEH, unless the MPPEH has received an initial inspection by UXOQP who determined the risk of movement is acceptable.

Amendment No. 0001

Section 01 35 30 Page 19

Chapter 2: MEC-Related Activities Personnel 9

(d) Be supervised or, if required, escorted by a UXOT (see Paragraph 2.2.b.(1)(k)) or UXOQP within areas known or suspected to contain MEC. The need for an escort is determined by a risk assessment that considers the support or tasks to be performed. Escorts will help ensure MEC and MPPEH on the surface, and subsurface anomalies are avoided.

(e) Be supervised by a UXO-TIII or above when performing activities in areas where there is a medium to high probability that MEC will be encountered, as determined by a risk assessment. Activities that may be performed by SP include:

1. Conducting visual or technology-aided sweeps for surface MEC.

2. Conducting geophysical surveys for subsurface anomalies.

3. Performing, when necessary, field maintenance and/or function checks on geophysical instruments and related equipment within an area known or suspected to contain

MEC.

4. Moving MPPEH (e.g., munitions debris and range-related debris) that has received an initial inspection by UXOQP who determined the risk of movement is acceptable for further inspection or processing per approved DDESB procedures.

b. UXOT. These personnel perform a variety of MEC-related activities.

(1) UXO-TI. When directed or supervised by a UXOQP, must be able to:

(a) Investigate for and classify MEC and MPPEH, including identifying explosive residues in media (soil, oil, etc.), buildings and installed equipment.

(b) Identify different types of military munitions, including identifying whether a military munition’s fuze is armed or unarmed.

(c) Excavate subsurface anomalies for identification.

(d) Move (e.g., consolidate) MEC, specifically UXO or DMM, within a munitions response site (MRS) or on an operational range after the UXOSO and SUXOS have jointly evaluated and determined the risk of movement to be acceptable.

(e) Operate vehicles transporting explosives, MPPEH or MDEH on site. (Individuals must be appropriately licensed for the class of vehicle being operated.)

(f) Transport military munitions, commercial explosives, and/or MDEH that meets the above criteria that has been determined safe for transport over public traffic routes (PTR).

Such munitions and explosives must be packaged in a manner that allows their safe transport and complies with Department of Transportation (DOT) and other applicable federal and State laws, and DoD policies. (Note: Only UXO determined to be safe for transport by EOD personnel may be transported over a PTR.)

Amendment No. 0001

Section 01 35 30 Page 20

Chapter 2: MEC-Related Activities Personnel 10

(g) Prepare electric and non-electric firing systems.

(h) Set up decontamination stations and decontaminate CA-contaminated personnel, military munitions and other material of interest (e.g., munitions debris, glass vials) per approved plans. The performance of these functions may require additional training.

(i) Assist UXOQP in documenting the explosives safety status of MPPEH.

(j) Construct engineering controls (protective works).

(k) Escort personnel who are not directly involved in MEC-related activities (e.g., SW, SP, visitors to cultural sites) on property known or suspected to contain MEC, but have an operational requirement and authorization to access such property. Although escort by a UXO- TI is typically performed under the supervision of a UXOQP, the responsible commander or authority may approve UXO-TI personnel to perform escort duties without supervision. Such approval must be, based on an approved risk assessment and implementation of methods to mitigate potential exposures.

(2) UXO-TII. Must be able to:

(a) Perform the functions of a UXO-TI.

(b) Store explosive materials per applicable guidance, including preparing on-site holding areas to temporarily store and secure MEC or MPPEH, and other explosives (e.g., donor charges).

(c) Determine, using a variety of techniques (e.g., global positioning equipment, land navigation techniques), and record the location of subsurface anomalies, surface MEC and other material of interest in a field environment.

(d) Perform field-collection and -testing procedures to identify explosives-contaminated media or material (e.g., equipment used for the load-assemble-pack of military munitions).

(e) Inspect and document the explosives safety status of MPPEH.

(f) Supervise, as required, SW, SP, and UXO-TI.

(3) UXO-TIII. Must be able to:

(a) Perform the functions of a UXO-TI and UXO-TII.

(b) Ensure compliance with a DoD Military Service- and/or DDESB-approved required explosives safety submissions (RESS).

Amendment No. 0001

Section 01 35 30 Page 21

Chapter 2: MEC-Related Activities Personnel 11

(c) Supervise and perform on-site destruction or demilitarization of MEC in place or at a consolidated detonation site. This includes determining where and when it is safe to initiate destruction and when engineering controls are required to mitigate the effects of a detonation.

(d) Implement an explosives storage plan per applicable guidance.

(e) Prepare administrative reports required for munitions responses (e.g., daily UXO team report), operational range clearance activities and similar operations.

(f) Develop and implement standard operating procedures and work plans for munitions responses and operational range clearance activities.

(g) Assist in the preparation of risk and hazard analyses.

(h) Conduct daily site safety briefings.

(i) Supervise the conduct of the different types of MEC-related activities performed at a site.

(j) Determine if MDEH, which is not known or suspected to be UXO, is safe to ship and properly documented for transport over PTR per Technical Bulletin 700-2, Naval Sea Systems Command Instruction 8020.8C, Technical Order 11A-1-47.

(k) Package military munitions, commercial explosives, and MDEH that has been determined safe for transport over PTR.

(l) Serve as UXO team leader.

c. UXOQP. These personnel conduct, manage or oversee MEC-related activities (e.g., reacquire and investigate anomalies, document explosives safety status of materials) required during munitions responses and operational range clearance activities and/or verify the completion of such responses and activities safely and per applicable requirements and approved plans. By definition, UXO-TII and UXO-TIII are considered both UXOTs and UXOQP.

(1) UXOQCS. Must be able to:

(a) Perform the functions of a UXOT.

(b) Develop and, upon approval, implement the project’s quality control (QC) plan for MEC-related activities per applicable requirements.

(c) Conduct and document QC audits of MEC-related activities for compliance with applicable requirements.

(d) Identify, document, report and ensure completion of corrective actions to ensure MEC-related activities comply with applicable requirements.

Amendment No. 0001

Section 01 35 30 Page 22

Chapter 2: MEC-Related Activities Personnel 12

(e) Ensure compliance with a DoD Military Service – and/or DDESB-approved

RESS.

(f) Prepare QC reports.

(2) UXOSO. Must be able to:

(a) Perform the functions of UXOT.

(b) Develop and, upon approval, implement explosives and health and safety plans and programs per applicable DoD, federal, State, and local requirements.

(c) Ensure compliance with a DoD Military Service- and/or DDESB-approved

RESS.

(d) Analyze the potential risks (e.g., operational, explosives safety, general safety) associated with MEC-related activities and develop and implement required, mitigating measures.

(e) Establish and ensure compliance with site-specific explosives safety requirements, including, but not limited to:

1. Enforcing personnel limits and explosives safety quantity distance (ESQD) arcs for explosive-related operations.

2. Conducting, documenting, and reporting the results of safety inspections and ensuring implementation of corrective actions.

3. Ensuring protective works and safety equipment within an exclusion zone are used, when required; and operated per manufacturer’s specifications, applicable DDESB approvals, DoD policy, and federal, State, or local statutes, regulations, and codes.

(f) Ensure that air-monitoring equipment is operated and maintained properly at sites with known or potential airborne contaminants (e.g., CWM sites).

(g) Evaluate the risk of movement (e.g., consolidation) of MEC within an MRS or on an operational range with the SUXOS, and provide approval for movement by UXOT when the risk of movement is determined to be acceptable.

(3) SUXOS. Must be able to:

(a) Perform the functions of a UXOT, UXOQCS, and UXOSO.

(b) Ensure compliance with a DoD Military Service- and/or DDESB-approved

RESS.

Amendment No. 0001

Section 01 35 30 Page 23

Chapter 2: MEC-Related Activities Personnel 13

(c) Plan, coordinate, and supervise all on-site munitions response and operational range clearance activities.

(d) Supervise up to ten UXO teams.

(e) Assist in development of required plans (e.g., health and safety plans).

(f) Review all field reports (e.g., daily reports, audits) and approve UXO team reports.

(g) Evaluate the risk of movement of UXO or DMM within an MRS or operational range with the UXOSO, and provide approval for movement by UXOT when the risk of movement is determined to be acceptable.

d. Dive-Qualified Personnel. Some MEC-related activities require personnel also be dive-qualified. Divers who are performing the duties of a UXOT or UXOQP must meet this TP’s criteria for the duties performed and possess the dive-related certifications required for the tasks they are to perform or supervise. An SUXOS, UXOSO, or UXO-TIII providing supervision of MEC-related activities from the surface do not need to possess diver certification.

(1) Dive-qualified personnel will meet the requirements of 29 CFR 1910, Subpart T, and possess either:

(a) Dive-related certifications (e.g., dive master, surface-supplied air diver, surface supplied mixed-gas diver), as required for the tasks they are to perform or supervise, from an Association of Commercial Diving Educators (ACDE)-accredited school whose curriculum meets the America National Standards Institute (ANSI) Standard ANSI/ACDE-01; or

(b) A training certificate with a valid Association of Diving Contractors (ADC) Commercial Diver Certification Card for the appropriate training level.

(2) Divers who are performing MEC-related activities underwater must at a minimum meet the qualifications for a UXO-T1. Such divers may be provided guidance from an SUXOS, UXOSO, or UXO-TIII on the surface. This requires that the individual providing the guidance have real-time voice communication with the diver and real-time visual or imaging for confirmation of the material (e.g., military munitions, munitions debris) the diver is encountering. An SUXOS, UXOSO, or UXO-TIII providing supervision of MEC-related activities from the surface do not need to possess diver certification.

Amendment No. 0001

Section 01 35 30 Page 24

Appendix to Chapter 2: UXO Position Descriptions 14

APPENDIX

DEPARTMENT OF LABOR, SERVICE CONTRACT ACT DIRECTORY

OF OCCUPATIONS - UXO POSITION DESCRIPTIONS1

A.1. 29491 UXO-TI

a. Assists in:

(1) Performing reconnaissance and classification of UXO.

(2) Identifying U.S. and foreign guided missiles, bombs and bomb fuzes, projectiles and projectile fuzes, grenades and grenade fuzes, rockets and rocket fuzes, land mines and associated components, pyrotechnic items, military explosives, and demolition materials.

b. Performs location of subsurface UXO using military and/or civilian magnetometers.

(1) Assists in performing excavation procedures on buried UXO.

(2) Performs operator maintenance of military and/or civilian magnetometers.

(3) Locates surface UXO using visual means.

(4) Assists in transporting and storing UXO and demolition materials.

c. Assists in:

(1) Preparing non-electric firing system for a UXO disposal operation.

(2) Preparing electric firing system for a UXO disposal operation disposing of ammunition/ explosives by burning; disposing of ammunition/explosives by detonation.

(3) Operating a personnel decontamination station. Dons and doffs appropriate personal protective equipment in contaminated areas. Assists in the inspection of salvage UXO-related material and erection of UXO-related protective works.

A.2. 29492 UXO-TII

a. Performs reconnaissance and classification of UXO. Identifies U.S. and foreign guided missiles, bombs and bomb fuzes, projectiles and projectile fuzes, grenades and grenades fuzes rockets and rocket fuzes, land mines and associated components, pyrotechnics, military explosives, and demolition materials.

1 Refer to http://www.dol.gov/whd/regs/compliance/wage/ for the current versions of these descriptions.

Amendment No. 0001

Section 01 35 30 Page 25

Appendix to Chapter 2: UXO Position Descriptions 15

b. Locates subsurface UXO using military and/or civilian magnetometers.

(1) Performs excavation procedures on buried UXO by manual means; mechanical means.

(2) Performs operator maintenance of military and/or civilian magnetometers.

(3) Locates surface UXO using visual means. Operates motor vehicle transporting

UXO.

(4) Prepares an on-site safe holding area for UXO.

(5) Performs storage of UXO and demolition materials.

(6) Prepares a UXO disposal site.

(7) Prepares non-electric firing system for a UXO disposal operation, electric firing system for a UXO disposal operation, and a detonating cord firing system.

(8) Disposes of UXO/explosives by burning or detonation.

(9) Operates a personnel decontamination station.

(10) Dons and doffs appropriate personal protective equipment in contaminated areas.

c. Inspects salvage UXO-related material.

(1) Erects UXO-related protective works.

(2) Determines a magnetic azimuth using a lensatic compass.

(3) Performs field expedient identification procedures to ID explosive-contaminated soil.

(4) Performs emergency leak seal and packaging of chemical warfare material.

(5) Uses radiographic (x-ray) equipment.

A.3. 29493 UXO-TIII

a. Performs reconnaissance and classification of UXO. Identifies U.S. and foreign guided missiles, bombs and bomb fuzes, projectiles and projectile fuzes, grenades and grenade fuzes, rockets and rocket fuzes, land mines and associated components, pyrotechnic items, military explosives, and demolition materials.

b. Supervises the location of subsurface UXO using military and/or civilian magnetometers.

Amendment No. 0001

Section 01 35 30 Page 26

Appendix to Chapter 2: UXO Position Descriptions 16

(1) Supervises the:

(a) Excavation and recovery of subsurface UXO.

(b) Construction of UXO-related protective works.

(c) Location of surface UXO by visual means.

(d) Transporting and storing UXO assuring compliance with federal, State, and local laws.

(e) Disposal of UXO by burning/detonation.

(f) Preparation of a UXO disposal site.

(g) Preparation of an on-site safe holding area for UXO.

(2) Determines UXO-related storage compatibility.

(3) Prepares an explosives storage plan.

(4) Supervises donning and doffing of personal protective equipment, operation of a personnel decontamination station, and maintenance and operator checks on all team equipment.

(5) Prepares UXO-related administrative reports and standard operating procedures.

(6) Conducts daily team safety briefing.

c. Supervises segregation of UXO-related scrap from non-UXO-related scrap, safe-handling procedures, team preventive medicine, and field sanitation procedures.

(1) Performs risk hazard analysis; interpret x-ray of UXO.

(2) Supervises field expedient identification procedures to ID explosives contaminated soil, the determining of a magnetic azimuth using a lensatic compass, emergency leak sealing.

and packaging of chemical warfare materiel.

A.4. 29494 UXO SAFETY ESCORT

a. Responsible for the safe escort of non-UXOQP who are not directly involved in specific UXO clearance site work, but have activities to perform within restricted/exclusion areas. Such personnel may include, but are not limited to, contractor personnel involved in the UXO cleanup, cultural visitors, surveying personnel, equipment operators, archaeologists, conservationists, geologists, news media, visiting government personnel, and other personnel as directed.

Amendment No. 0001

Section 01 35 30 Page 27

Appendix to Chapter 2: UXO Position Descriptions 17

b. Ensures safety during the transit of persons being escorted by scanning visually in the immediate path of the escorted party, and redirecting the party as necessary to avoid unexploded ordnance and other hazards.

c. Is involved with hazard recognition and avoidance only, not the execution of UXO search or clearance actions.

d. Must have UXO training qualifications.

A.5. 29495 SP

a. Assist UXO personnel in the clearance of UXO, operating only under the direct working supervision of qualified UXO specialist and/or UXO supervisory personnel.

b. Conduct visual and/or instrumented UXO search activities in the field and operate ordnance detection instruments and similar equipment.

c. Remove UXO fuze remnants, fragments and related debris only after such items have been positively identified, inspected and verified as safe to handle by a qualified UXO specialist.

d. Are not involved in the execution of explosives operations.

e. Must have site and job specific contractor training, but does not require UXO qualifications.

Amendment No. 0001

Section 01 35 30 Page 28

Chapter 3: UXO-TI Training Standards 18

CHAPTER 3

UXO-TI TRAINING STANDARDS

3.1. MINIMUM TRAINING STANDARDS FOR UXO-TI

a. This chapter outlines the minimum training standards for a UXO-TI. Personnel who are trained as a UXO-TI must demonstrate the requisite knowledge and ability to perform required tasks in compliance with applicable operational and explosives safety requirements. Candidates for a UXO-TI position must successfully complete:

(1) 200 hours of explosives safety training as described in Paragraph 3.2. or a comprehensive assessment of the individual’s ability to successfully perform as a UXO-TI. The course content must convey the information and skills needed to conduct MEC-related activities per applicable requirements. Both the course and comprehensive assessment must include practical exercises evaluating the skills required.

(2) 40 hours of HAZWOPER training per 29 CFR 1910.120.

b. An institution of higher education must provide this training or conduct this assessment and:

(1) Certify successful completion of the course requirements or a comprehensive assessment through written exams and practical exercises.

(2) Have programmatic accreditation by a U.S. Secretary of Education nationally recognized college or university educational accrediting agency, be a component member of a nationally recognized university's system, or be designated by statute as an agency of higher education and have a demonstrated history of providing quality training programs.

c. Before being employed as a UXO-TI, an applicant must provide the perspective employer documentation of successful course completion or successful completion of a comprehensive assessment from an institution of higher education that meets the above criteria. The employer must verify that the individual was trained by the training institution and the institution meets the above requirements.

3.2. CURRICULUM AND TRAINING OBJECTIVES FOR UXO-TI

a. Munitions Responses to MEC

(1) Description. Understand the purpose, requirements, and procedures for a munitions response to MEC. This training includes explosives safety and environmental requirements applicable to the conduct of munitions responses to MEC.

Amendment No. 0001

Section 01 35 30 Page 29

Chapter 3: UXO-TI Training Standards 19

(2) Objectives

(a) Define terms and identify abbreviations.

(b) Describe the purpose for munitions responses.

(c) Describe planning, safety, and environmental requirements for conducting munitions responses.

(d) Identify the documents (e.g., work plan, accident prevention plan) that should be available for review by field team members.

(e) Describe the typical field tasks of a munitions response and their purpose.

(f) Describe the required process to inspect and document the explosives safety status of MPPEH as either material documented as safe (MDAS) or as MDEH.

(g) Discuss how to and the importance of maintaining a chain of custody for MDAS and MDEH.

(h) Describe the consequences of losing the chain of custody for MDAS and MDEH.

(i) Discuss potential liability concerns associated with evaluating MPPEH and documenting its explosives safety status as MDAS or MDEH.

(j) Describe the proper assembly of protective works.

(k) Describe the general operation of soil sifting, magnetic, and eddy current equipment as a method to separate MEC and munitions debris from soil.

(l) Describe documentation required from a field team conducting MEC activities.

b. Operational Range Clearance Activities and Similar Operations

(1) Description. Understand the purpose, requirements, and procedures for the conduct of operational range clearance activities and similar operations. This training includes explosives safety and environmental requirements applicable to the conduct of operational range clearance activities and similar operations.

(2) Objectives

(a) Describe the purpose of operational range clearance activities and similar operations and how they differ from munitions responses to MEC.

(b) Describe how operational ranges are designed (e.g., impact areas, safety buffer zones) and used.

Amendment No. 0001

Section 01 35 30 Page 30

Chapter 3: UXO-TI Training Standards 20

(c) Describe planning, safety, and environmental requirements for conducting operational range clearance activities.

(d) Describe the typical field tasks for the conduct of operational range clearance activities and how they differ from munitions responses to MEC.

(e) Describe the potential hazards associated with operational range clearance activities.

(f) Describe documentation required from a field team conducting operational range clearance activities.

(g) Describe the required process to inspect and document the explosives safety status of MPPEH as either MDAS or as MDEH.

(h) Discuss the importance of properly processing and managing MPPEH, MDAS, and MDEH, including the importance of maintaining the chain of custody.

(i) Describe the consequences of losing the chain of custody.

(j) Discuss potential liability concerns associated with evaluating MPPEH and documenting its explosives safety status as MDAS or MDEH.

c. Measurements and Mathematical Computations

(1) Description. Understand the methods for conversion between the U.S. customary and metric systems of measurements and basic mathematical computations.

(2) Objectives

(a) Identify metric prefixes.

(b) Describe mathematical conversions within the metric system.

(c) Convert units from U.S. customary to metric and metric to U.S. customary.

d. Electricity

(1) Description. Understand the basics of electricity and circuitry as applied to MEC-related activities.

(2) Objectives

(a) Define terms and identify abbreviations and symbols.

Amendment No. 0001

Section 01 35 30 Page 31

Chapter 3: UXO-TI Training Standards 21

(b) Describe electrical conductivity and its characteristics in different materials.

(c) Describe types of cells and batteries, their construction features, and process used to generate electro-motive force.

(d) Describe current flow, factors that affect current flow (including switches) and units of measurement of current flow.

(e) Describe electrical resistance and the factors that affect resistance.

(f) Describe the operation of a series direct current (DC) circuit with respect to Ohm’s Law.

(g) Describe the operation of basic parallel DC circuits with respect to the determination of equivalent resistance.

(h) Describe capacitance in terms of charging and discharging a capacitor.

(i) Diagram a basic circuit such as may be used in electric firing system.

e. Physics

(1) Description. Understand the basic physics as applied to MEC-related activities.

(2) Objectives

(a) Define terms and identify abbreviations and symbols.

(b) Describe forces and how they are graphically represented.

(c) Describe Newton’s first and third laws of motion.

(d) Describe the difference between weight and mass.

(e) Describe hydrostatics with respect to fluid pressure.

(f) Describe properties of matter.

(g) Define motion, work, and energy.

(h) Describe measures of and forces affecting motion.

(i) Identify the physical laws affecting gases.

(j) Define magnetism.

Amendment No. 0001

Section 01 35 30 Page 32

Chapter 3: UXO-TI Training Standards 22

f. Military Munitions - Explosives and Explosive Effects

(1) Description. Understand the basics of explosives and explosive effects.

(2) Objectives

(a) Define terms and identify abbreviations and symbols.

(b) Summarize the history of explosives.

(c) Define propellants, explosives, and pyrotechnics.

(d) Describe characteristics of military munitions (i.e., explosives, propellants, and pyrotechnics).

(e) Identify the types of high explosives groups (primary, secondary, main charge).

(f) Identify forms and classes of propellants and black powder, pyrotechnic, and tracer compositions.

(g) Describe the functioning of an explosive train.

(h) Define explosion and describe types of explosions (detonations, low order detonations, deflagrations).

(i) Describe forms of energy produced by explosions.

(j) Describe effects of an explosion (pressure wave, fragments, debris, thermal, ground shock).

g. Military Munitions - Fuze Functioning

(1) Description. Understand how fuzes function.

(2) Objectives

(a) Define terms and identify abbreviations.

(b) Describe fuze forces.

(c) Describe fundamental principles of fuzes, fuze arming, and firing principles.

(d) Describe fuze components.

(e) Describe methods of employment and uses of fuzes.

Amendment No. 0001

Section 01 35 30 Page 33

Chapter 3: UXO-TI Training Standards 23

(f) Describe typical arming/functioning of fuzes.

(g) Describe fuze types.

h. Explosives Safety Precautions

(1) Description. Understand explosives safety precautions as they apply to the conduct of MEC-related activities, including:

(a) The different categories of MEC (i.e., UXO, DMM, or munitions constituents (MC) that are explosives and in concentration high enough to pose an explosive hazard), and MPPEH and MDEH.

(b) The use of hazards of electromagnetic radiation to ordnance (HERO) safe equipment.

(2) Objectives

(a) Define terms and identify abbreviations and symbols.

(b) Describe the purpose of explosives safety precautions.

(c) Describe safety considerations that apply by categories of MEC and MPPEH and

MDEH.

(d) Describe basic safety precautions for:

1. Explosive-loaded munitions.

2. Submunitions.

3. Toxic chemical-loaded munitions.

4. Pyrotechnic and incendiary munitions.

5. Smoke-loaded munitions.

6. Fuzing systems.

7. Small arms ammunition.

8. Training military munitions.

9. Practice military munitions.

10. Underwater munitions.

Amendment No. 0001

Section 01 35 30 Page 34

Chapter 3: UXO-TI Training Standards 24

i. Military Munitions Identification

(1) Description. Provide a detailed description (e.g., family, group, type) and identify military munition, and applicable specific safety precautions based on type. (See Ammunition Terms.)

(a) Surface-fired, launched, or placed munitions:

1. Projectiles (gun, mortar, howitzer).

2. Small arms ammunition.

3. Land mines and associated components.

4. Infantry rockets and rocket fuzes.

5. Grenade and grenade fuzes.

(b) Air launched or fired munitions:

1. Bombs and bomb fuzes.

2. Guided missiles and missile fuzes.

3. Large rockets and rocket fuzes.

4. Submunitions.

(c) CWM (i.e., chemical munitions and CA in other than munitions configurations).

(d) CAIS.

(e) Smokes and pyrotechnics.

(2) Objectives

(a) Define terms and identify abbreviations and symbols.

(b) Provide a detailed description and identify military munition, and applicable specific safety precautions based on type..

(c) Demonstrate comprehension and detailed knowledge of live, training, and practice munitions.

Amendment No. 0001

Section 01 35 30 Page 35

Chapter 3: UXO-TI Training Standards 25

(d) Recognize munitions’ color codes and markings.

(e) Describe the basic safety precautions for explosive-initiating components.

(f) Describe the safety precautions for munitions by category or group.

j. Underwater Munitions Identification

(1) Description. Understand underwater munitions.

(2) Objectives

(a) Define terms and identify abbreviations and symbols.

(b) Provide a detailed description and identify military munition, and applicable specific safety precautions based on type. .

(c) Demonstrate comprehension and detailed knowledge of live training and practice underwater munitions by category and specific safety precautions based on type.

(d) Recognize munitions’ color codes and markings.

(e) Describe the basic safety precautions for explosive-initiating components.

(f) Describe the safety precautions for underwater munitions.

k. Detection Equipment

(1) Description. Understand general, physical, functional, operational, and maintenance of detection equipment for:

(a) Location of subsurface anomalies using various technologies during the conduct of geophysical surveys.

(b) Detection of subsurface anomalies.

(c) Basic geophysical investigation (e.g., anomaly identification, mapping, target discrimination, QC processes).

(2) Objectives

(a) Describe the purpose of geophysical survey equipment; operational characteristics, and capabilities.

(b) Describe the theory of geophysical surveys.

Amendment No. 0001

Section 01 35 30 Page 36

Chapter 3: UXO-TI Training Standards 26

(c) Describe data analysis including the advanced geophysical classification process.

(d) Describe all major and associated components including displays, controls, and indicators.

(e) Describe the purpose of a geophysical system verification and the various tasks involved.

(f) Describe operational tasks and preventive maintenance procedures.

(g) Understand how to inventory and maintain equipment.

(h) Understand typical instrument outputs and their use in munitions responses.

l. PPE

(1) Description. Understand all relevant PPE.

(2) Objectives

(a) Identify where PPE requirements for MEC-related activities are specified and who is responsible for determining whether PPE is required and changing PPE requirements at a site.

(b) Understand the capabilities and limitations of PPE, given the hazards that may be present.

(c) Understand the requirements for employing PPE safely.

(d) Describe the requirements and process for performing decontamination.

m. Demolition Materials

(1) Description. Understand demolition materials and their use including:

(a) Military and commercial explosives (U.S. and foreign).

(b) Initiating components and systems.

(2) Objectives

(a) Define terms and identify abbreviations and symbols.

(b) Describe military explosives, commercial explosives, and demolition materials and when each might be used.

Amendment No. 0001

Section 01 35 30 Page 37

Chapter 3: UXO-TI Training Standards 27

(c) Describe the purpose of demolition materials and specialized explosive techniques.

(d) Describe tools and equipment used during demolition operations.

(e) Describe demolition accessories.

(f) Describe electric power sources and test sets used with demolition firing circuits.

(g) Describe demolition charge initiators.

(h) Describe demolition charges, charge kits, and assemblies.

(i) Describe safety precautions for preparation and firing of demolition materials.

n. Firing Systems

(1) Description. Understand firing systems and their use.

(2) Objectives

(a) Describe detonating cord demolition procedures.

(b) Describe electric and non-electric firing systems.

(c) Describe safety precautions for preparation and firing of demolition materials, including HERO and static discharge precautions for electric initiators.

(d) Prepare firing…