J16116-23.pdf

PDF 176 KB Posted

Attached to
chrome plating of cover tubes
Solicitation number
W911N2-27-Q-A011
Issued by

About this file

This document is a technical appendix detailing hard chrome plating repair procedures for the J16116-23 Cover Tube, a component of the J-16116 assembly.

The cover tube measures approximately 38 inches in overall length, with a short section of 9-3/8 inches at 3-1/2 inches outer diameter (OD) and a longer section of 28-5/8 inches at 4 inches OD, with a 3-inch inner diameter (ID) throughout except in threaded areas. The part weighs 48 pounds and has an unknown substrate material. The repair process begins with pre-grinding and evaluation to remove damage from the seal area, maintaining a minimum allowable diameter of 3.970 inches after grinding, with a repaired seal area width of 1.38 + 0.12/-0.03 inches. Standard repair involves chrome plating the seal area in accordance with SAE AMS-QQ-C-320, Class 2 (superseding QQ-C-320), followed by final grinding to achieve a diameter of 4.000 to 4.005 inches with a surface finish of 12 to 16 microinches. The transition from the chrome-plated seal area to the remainder of the 4-inch diameter tube must be maintained consistently and free of irregularities to prevent seal damage during assembly. A 0.0625-inch by 0.0625-inch chamfer must be ground at the diameter change edge, with no more than 0.0625 inch of material removed. Non-chromed areas are cleaned using coarse Scotch-Brite surface conditioning on the exterior and wire brushing on the interior. Non-standard repair processes, such as welding to repair surface pitting, require Government Technical Point of Contact (TPOC) review and Contract Officer's Representative (COR) approval before proceeding.

View the file

Other files

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

Cover Tube J16116-23 Hard Chrome Plating Process Details

NOTE: Pictures within this appendix are provided to show part configuration and geometry.

They are not intended to demonstrate the condition of the parts as shipped from LEAD.

J16116-23, Cover Tube

Drawing: Part of J-16116 assembly, (see 11686299_19207.pdf) included in requirements package. The fabrication drawing for the part is considered by the manufacturer to be proprietary; therefore, only the assembly is available. The cover tube covers the screw and is shown extending out of the casing on the left.

Substrate: unknown

Approximate dimensions: overall length is 38"; short length is 9-3/8", OD is 3-1/2"; longer length is 28-5/8", OD is 4"; ID is 3" for total length except for threaded areas.

Weight: 48 lb

Procedures:

Pre-grind and Evaluate

1. Strip/pre-grind the seal area to remove damage and to prepare the area for re-plating. A minimum of material should be removed to clean up the surface. The minimum allowable diameter of the seal area after pre-grinding is 3.970 inches.

2. The width of the repaired seal area is to be 1.38 + 0.12/- 0.03 inches. If the chrome plated area of the part received is less than the requirement, pre-grind and prepare part to meet the plated width requirements in the plating and finishing steps. If the chrome plated area of the part received is greater than the requirement, contact the Government before proceeding.

3. Inspect the part. If the surface cannot be restored through the Standard Plate and Finish procedures below, document and communicate to the Government:

a. That the part can be repaired using Non-Standard Repair Processes. The Government will review documentation and approve or reject these requests on a part by part basis. Do not proceed with additional repair processes without approval.

b. That the part is not repairable through Standard or Non-Standard Processes documented in this Appendix.

Standard Plate and Finish

1. Chrome plate the seal area to build up size for final grinding. Mask off all other areas to preclude plating. Chrome plate the seal area surface IAW SAE AMS-QQ-C-320, Class 2 (supersedes QQ-C-320).

2. Final grind the re-chromed seal area to a diameter of 4.000 to 4.005 inches, with a surface finish of 12 to 16 microinches.

3. Maintain consistent diameter over the transition from the chrome plated seal area to the remainder of the 4 inch diameter of the tube. A seal must pass across this transition during assembly. The transition must be free of ridges, troughs and other surface irregularities that could damage the seal during assembly.

4. Grind the edge of the re-chromed area at the diameter change to remove excess chrome.

Provide a 0.0625 inch by 0.0625 inch chamfer to allow for seal installation. Do not remove more than 0.0625 inch of material from the edge.

5. Clean the non-chromed areas on the tube to remove rust, carbon and other residue. This has been accomplished in the past using coarse Scotch-Brite surface conditioning belt on the exterior and a wire brush on the interior.

Non-standard Repair Processes

1. Repair surface pitting by welding. The Government Technical Point of Contact (TPOC) will review the proposed weld repair and provide a recommendation to the Contract Officer’s Representative (COR) to approve or reject this additional repair.

Picture of J16116-23, Cover Tube:

Another View of Cover Tube, J16116-23

1. Chamfered side of seal area

2. Transition side of seal area

SEAL

INSTALL

DIRECTION

File details come from the government source that posted it. Updated .