Attachment 0001_MEO_B2008A.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 5-DEC-09 1401-R-E

AR 70-62 •11 May 2016 B 2008 Rev A

May 23, 2018 11

IUID Parts Marking IUID Updates for H-60 Pilot-Assist Hydraulic Module Assembly P/N 70652-02620-044

70652-02620-046

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

4) Normal - Can be implemented with normal priorityPRIORITY IMPLEMENTATION CATEGORY

UH60 DAA

DMWR 1-1560-293, dtd 31 August 2012 TN 147601A 4/16/2018

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

Update IUID Revisions to Parts Marking requirements. Add Fabrication Note and Updates to IUID Query requirements.

DIETZ.BRITTANY

.HELEN.1291995

Digitally signed by

DIETZ.BRITTANY.HELEN.129

1995205 Date: 2018.05.15 08:11:24 -05'00'

NOLEN.OTIS.

F.1231157146

Digitally signed by

NOLEN.OTIS.F.1231157146

Date: 2018.05.15 07:22:08 -05'00'

Otis Nolen (Camber Corporation)

HORN.REINHOL

D.J.1087783495

Digitally signed by

HORN.REINHOLD.J.1087783

Date: 2018.05.15 08:40:56 -05'00'

Brittany Dietz Ron Horn PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

d Warning

Distribution Statement D:- Distribution authorized to Department of Defense and U.S. DoD contractors only to protect critical technology effective as of 26 June 2014. Other requests for this document must be referred to U.S. Army Aviation and Missile Research, Development and Engineering Center, ATTN: RDMR -AEM , Corpus Christi, TX 78419-5211

ADD Polyurethane coating Warning to read:

"Polyurethane, MIL-PRF-85285, Type I, Class, H Clear

Polyurethane coating is a carcinogenic risk. May cause birth defects People with chronic lung or breathing problems or persons that have reactions to isocyanates are not to use this product or be in the area where it is being used. Extreme overexposure could result in unconsciousness and possible death. It is an irritant to eyes, skin and respiratory tract. May cause sensitization and allergic respiratory and skin reactions. Highly flammable. It is too used with mechanical ventilation / local exhaust. Use an approved respirator if exposure exceeds Permissible Exposure Limits and/or Threshold Limit Values.

Wear approved gloves, skin, and eye protection. Avoid oxidizing agents and ignition sources."

MED FORM 04 APR 2017

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-3

1-10.4

1-10.5

REPLACE 1-10.4 second paragraph and ADD sub-paragraphs a and b as follows:

"Figure 1-3, Sheet 1 of 2, shows the IUID data plate format options for this component. The manufacturer IUID data plate format represents components originally UID-marked during production. The legacy IUID data plate formats represents components originally UID-marked post-production during an M&O event or in the field (commonly referred to as legacy components).

a. Manufacturer IUID Data Plate (Option A). The IUID data plate may contain one or two 2-D data matrices. The UID 2-D data matrix is encoded with a Construct 2 UII using DI or TEI data qualifiers 17V or CAG (manufacturer's CAGE code), 1P or PNO (original part number) and S or SEQ (manufacturer's serial number). In addition to the UII, a 30P or PNR (current part number) may also be encoded in the UII data matrix as additional information or in a separate 2-D data matrix. The 30P or PNR being the Sikorsky part number upon completion of the M&O event.

b. Legacy IUID Data Plate (Option B). The data plate contains one 2-D data matrix encoded with a Construct 1 UII that uses TEIs, SPL (supplier's CAGE code) and UCN (supplier's unique component number) as data qualifiers. In addition to the UII, a PNR (current part number) is also encoded in the data matrix as additional information in a separate 2-D data matrix. The PNR being the Sikorsky part number upon completion of the M&O event."

ADD Note prior to paragraph 1-10.5 to read:

"NOTE

Prior to fabrication of the IUID data plates, the DoD IUID Registry shall be queried per paragraph 3-5.2."

AR 70-62 •11 May 2016

B 2008 Rev A

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E MED

1-4

1-10.5.a.

(1)

(2)

(3)

(3).(b)

(3).(c)

1-10.5.b

10.5.b.

CHANGE in 1-10.5.a.(1) "(TAMMS-A/MCDS) (App A, Websites)." to read: "(TAMMS-A/MCDS), Unique Identification (UID) database (App A, Websites)."

CHANGE "TAMMS-A/MCDS, UID database at https://tammsa.redstone.army.mil" to read:

TAMMS-A/MCDS, UID database (App A, Websites)."

CHANGE paragraph (2) to read:

"The second 2-D data matrix shall be encoded with the current Sikorsky part number using the TEI PNR (current Part Number) as the data qualifier. The PNR is the component’s Sikorsky part number upon completion of the M&O event."

CHANGE in paragraph (3) "at http://www.acq.osd.mil/dpap/pdi/uid/data_submission_information.html."

to read: "at DPAP UID (App A, Websites)." at end of first sentence.

CHANGE "original nameplate" to read: "identification data plate"

CHANGE "original nameplate" to read: "identification data plate"

CHANGE paragraph b first sentence to read: "If the Pilot-Assist Hydraulic Module Assembly has no IUID data plates present, an

UII ......".

CHANGE paragraph (2) to read: "The second 2-D data matrix shall be encoded with the current Sikorsky part number using the DI (30P) or TEI PNR (current part number) as the data qualifier. The (30P) or PNR is the component’s Sikorsky part number upon completion of the M&O event."

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-5

1-10.5.c

1-10.5.c.

1-10.5.d

1-10-5.e

1-10.6

Note

DELETE in 1-10.5.c "(see paragraph If the Pilot-Assist Hydraulic Module Assembly has compliant IUID data plate and the DoD IUID Registry record data matches data on the component".

CHANGE paragraph (2) to read: "The second 2-D data matrix shall be encoded with the current Sikorsky part number using the DI (30P) or TEI PNR (current Part Number) as the data qualifier. The (30P) or PNR is the component’s Sikorsky part number upon completion of the M&O event."

ADD Note prior to paragraph 1-10.5.d

The verification for minimum print quality grade applies to compliant IUID data plates that have been removed and will be reapplied. For components having an compliant IUID data plate that is installed (is not being removed during the M&O event), the IUID data plate can remain on the component provided the 2-D data matrix passes a readability check per paragraph 1-10.6.g."

CHANGE "(see App B, Table B-1)" to read "(Table B-1)".

ADD new Note prior to paragraph a. to read:

Allow TESA Tape (App C, Item 28) label stock to be conditioned to room temperature. Do not attempt to apply the IUID Data Plate when the component surface temperature is below 50° F."

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-7

1-8

3-1

1-10.6.e

1-10.6.g

3-5.2.1

Warning

Figure

Figure

Note

ADD Polyurethane Coating Warning prior to 1-10-6.e to read:

"WARNING

Polyurethane coating is a carcinogenic risk. May cause birth defects People with chronic lung or breathing problems or persons that have reactions to isocyanates are not to use this product or be in the area where it is being used. Extreme overexposure could result in unconsciousness and possible death. It is an irritant to eyes, skin and respiratory tract. May cause sensitization and allergic respiratory and skin reactions. Highly flammable. It is to use with mechanical ventilation / local exhaust. Use an approved respirator if exposure exceeds Permissible Exposure Limits and/or Threshold Limit Values. Wear approved gloves, skin, and eye protection. Avoid oxidizing agents and ignition sources."

CHANGE paragraph g "(see App B, Table B-1)" to read "(Table B-1)".

REPLACE Figure 1-3, Sheet 1 of 2 with figure found on page 9 of this

MEO.

REPLACE Figure 1-3, Sheet 2 of 2 with figure found on page 10 of this

MEO.

CHANGE in third Note "contracting officer (COR)" to read: "contracting officer representative (COR)"

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

3-2

3-5.2.1.a

3-5.2.1.b

3-5.2.1.b

Warning

REPLACE paragraph a to read:

"Inspect the Pilot-Assist Hydraulic Module Assembly for the presence of a 2-D data matrix or matrices via an IUID data plate (Figure 1-2), (Figure 1-3) or other IUID label media. If present, use a handheld data matrix reader (Table B-1) or an equivalent, to scan the 2-D data matrices for the presence of an UII. If a scan of a 2-D data matrix provides a UII, proceed to paragraph 3-5.2.1.d and/or 3-5.2.1.e. If the scan of the 2-D data matrix or matrices are not successful (unreadable or does not provide a UII) after two attempts, proceed to paragraph 3-5.2.1.b."

ADD Warning Isopropyl Alcohol prior to paragraph 3-5.2.1.b to read:

"WARNING

Isopropyl alcohol is flammable and toxic to eyes, skin, and respiratory tract. Wear protective gloves and goggles/face shield. Avoid repeated or prolonged contact. Use only in well ventilated areas (or use approved respirator as determined by local safety/industrial hygiene personnel).

Keep away from open flames, sparks, or other sources of ignition."

REPLACE paragraph b to read:

"Clean the 2-D data matrix or matrices with a cloth (APP C, item 11) moistened with isopropyl alcohol (App C, Item 10) and scan again. If the third scan is successful (provides a UII), proceed to paragraph 3-5.2.1.d.(1) and/or 3-5.2.1.e.(1). If the third scan is not successful (still unreadable or does not provide a UII), use the HRI to query the DoD IUID Registry (paragraph 3-5.2.1.d.(2)) and/or TAMMS-A/MCDS, UID database (paragraph 3-5.2.1.e.(2))."

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

3-3

3-4

3-5

3-5.2.1.c

3-5.2.1.d

3-5.3

3-5.4.

3-5.5.

3-9.1.n

Table

DELETE in 3-5.2.1.c "(only an original identification data plate)".

CHANGE in 3-5.2.1.d "Registry via WAWF" to read: "Registry via the

WAWF".

CHANGE in 3-5.3 heading to read: "IUID Life Cycle Events (LCE)."

CHANGE the "colon" to a "period" at end of paragraph.

CHANGE (TAMMS-A/MCDS, UID database at https://tamms-a.redstone.army.mil), to read: TAMMS-AMCDS (App A, Websites),"

CHANGE "TAMMS-A/MCDS, UID database at https://tamms-a.redstone.army.mil", to read: "TAMMS-AMCDS (App A, Websites),"

CHANGE "TAMMS-A/MCDS, UID database at https://tamms-a.redstone.army.mil)", to read: "TAMMS-AMCDS (App A, Websites)."

REPLACE "Table 3-1 new figure found on page 11 of this MEO.

REPLACE paragraph n. to read: "Remove identification plates (13, 16, 19, 23, 24, 25, 26, 27, and 28), nameplates (30, and 31) and IUID data plate (29), only if damaged.

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

A-2

C-2

C-2

A-5

App C

App C

CHANGE "Guidelines . . . . . . Guidelines for Registering Government Serialization, Type Designation and Ownership of Major End Items, Assemblies and Subassemblies and Capital Equipment" to read:

"DoD Guide . . . . . Department of Defense Guidelines for Registering Government Serialization, Type Designation and Ownership of Major End Items, Assemblies and Subassemblies and Capital Equipment"

REPLACE item Number 23 to read:

"Item Number: 23 National Stock Number: 8020-01-129-1143 Description: 1 IN. POLY-BRUSH, Foam (49AB6), JEN MFG Inc., or equivalent

U/M: BX"

ADD Item Number 28 to read:

"Item Number: 28 Description: TESA Tape, TESA Secure 6973 PV6 (matte black top layer/white under layer)

U/M: SH"

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

AR 70-62 •11 May 2016

Figure 1-3. IUID Data Plates (Sheet 1 of 2)

MED FORM 04 APR 2017

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

AR 70-62 •11 May 2016

Figure 1-3. IUID Data Plates (Sheet 2 of 2)

MED FORM 04 APR 2017

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

AR 70-62 •11 May 2016

Table 3-1. IUID Life Cycle Events.

IUID LIFE CYCLE EVENTS (LCE)

Event Definition

Abandoned

Property surrendered by a Federal agency after a written determination that the property has no commercial value, or the estimated cost of its continued care and handling would exceed the estimated proceeds from its sale. An item has no commercial value when it has neither utility or monetary value (either as useable property or as scrap)

Consumed Non-reversibly incorporated into another item

Destroyed – Accident Destroyed during a fire, natural disaster, or other unplanned natural or man-made incident

Destroyed – Combat Destroyed by the enemy during combat

Donated

Surplus property provided to a Service Educational Activity; a State, political subdivision, municipality, or tax-supported institution acting on behalf of a public airport; a public agency; a public body; a charitable institution; or any State or local government agency, and certain nonprofit organizations or institutions

Exchanged – Sold Provided to a supplier for credit Exchanged – Repair Provided to a supplier for an equivalent replacement part Exchanged – Warranty

Provided to a supplier for an equivalent replacement part or credit while under warranty

Expended – Normal Use

Such as in the firing of a missile during combat or consumed during a manufacturing process

Expended – Experimental/Target

Such as the firing of a missile during training exercises and for testing;

items destroyed while serving as a target during training exercises and tests

Leased Property that is granted to a lessee for a period of time in exchange for rent or other consideration

Loaned Owned by a DoD component and loaned to contractors, scientific institutions or other organizations

Lost Property that cannot be located or otherwise accounted for Reintroduced When an item is returned to DoD service

Retired Withdrawn from normal service; taken out of use. Includes decommissioned, stricken, sunken, transferred to AMARC/DRMS, etc.;

excludes temporary idling of the item

Scrapped Waste material that will not be reused or reprocessed Sold – Other Federal Title transferred to non-DoD Federal Agencies with compensation

Sold – State/Local Title transferred to non-Federal governmental entities with compensation

Sold – Foreign Govt. Title transferred to non-US governmental entities with compensation

Sold – Non-Govt. Title transferred to non-governmental entities such as churches, organizations, etc. with compensation

Sold – Historic Title transferred to a museum or similar entity with compensation Stolen Lost via theft

MED FORM 04 APR 2017