TIQ_-_Game_Viewer_Truck.docx

Technical Information Questionnaire (TIQ) October 2018 FAILURE TO PROVIDE ALL OF THE INFORMATION REQUIRED BELOW MAY RENDER YOUR PROPOSAL INELIGIBLE FOR AWARD Isuzu NPS 300, Game Viewer Truck The purpose of this questionnaire is to determine the suitability of your equipment to satisfy the requirements as stated in the specification. YOU MUST PROVIDE A RESPONSE TO ALL QUESTIONS. Failure to provide a response may result in the rejection of your proposal.

Units: The data provided in the TIQ shall be provided in English units, unless otherwise specified. Metric units may be provided if clearly defined and identified.

All written information shall be in English.

In addition to responding to the questions below, the offeror shall provide the following:

1. Vehicle and major component commercial literature or specification sheets or any other information that would substantiate the information provided. If your commercial literature does not provide information relating to a particular question, you are required to provide a written explanation of your ability to meet that particular requirement with your written proposal. Where indicated herein, supporting documentation must be provided along with the location of that information stated (e.g. page number, paragraph, etc).

0. Supporting documentation is required for sections: 3(a)1, 3(j)8, 6(a)1, and 14(a)1.

1. Identification of all modifications and/or redesigns to the previously manufactured base vehicle necessary to meet the requirements of the specifications. The offeror shall also explain in detail the reasons for the modifications or redesigns.

Information Notes:

(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number shall be shown.

(b) Curb Weight shall be weight of vehicle offered, completely equipped with coolant, fuel and lubricants, less the weight of the crew (driver and passenger - 175 pounds each).

(c) Gross Vehicle Weight (GVW) shown shall include curb weight of the vehicle, weight of the crew, (350 pounds total), the payload (20 passengers at 3,500 lbs total), and any extra stowed equipment.

GENERAL INFORMATION REQUIRED

Personnel Responding to Questionnaire:

(a) Name

(b) Job Title

(c) Company Name

(d) Telephone/Fax Numbers

(e) E-mail address

(f) Mailing Address

(g) Company Website Comments

Isuzu NPS 300, Game Viewer Truck

1. CONFIGURATION

(a) Has the vehicle been provided with all new parts?

(b) Is the vehicle a Game Viewer Truck, built on the Isuzu NPS 300 platform?

(c) Is the vehicle a 4x4 SWA (Single Wheel Axle), with a 20 passenger capacity?

(d) Are the truck and chassis both a 2018 model year or later?

(e) Are no more than 250 miles on the odometer?

Comments

2. SAFETY

(a) Does this vehicle meet all applicable US Federal Motor Vehicle Safety Standards (FMVSS)?

(b) If the vehicle does not meet FMVSS standards, which vehicle standards does the vehicle comply with?

Comments

3. EQUIPMENT

Is the vehicle equipped with: (Yes/No and briefly explain in comments as needed)

(a) All of the standard equipment typically found on a base Isuzu NPS 300 truck of this type?

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) listing all standard equipment found on a base Isuzu NPS 300 truck of this type must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

(b) Anti-sail mud flaps installed behind all vehicle wheels?

(c) A lockable tool box(es) or secured storage compartment(s)? Describe

1) Is the lockable tool box(es) or secured storage compartment)s) sufficient capacity to store all of the manufacturer’s standard equipment and accessories, and those listed below?

2) Standard tools required for simple operator level maintenance? ; if yes, check all that apply: |_| Wrench and socket set; |_| Screwdriver; |_| adjustable wrench; |_| pliers; |_| hammer; |_| Other

3) Tire changing tools?

4) Lifting jack? Capacity tons, Type

5) Three emergency warning triangles?

6) An ANSI compliant, 25 person first aid kit?

(i) Does the kit include at least bandages, scissors, adhesive tape, tweezers, eye wash, burn cream, cold compresses, anti-biotic cream, and an assortment of self-adhering band-aids?

7) A portable air compressor with a chuck to inflate tires, and a pressure gauge? (i) Are the hose and cord long enough to inflate all tires on the vehicle?

(d) Two 5 gallon (or 20 liter) jerry cans?

1) Is one jerry can labeled “Potable Water Only”, and the other labeled “Diesel Fuel Only” in English?

(e) Two frame-mounted tow hooks or eyes on the front and two at the rear of the vehicle?

(f) A tow bar?

(g) A bull bar?

(h) An ABC type fire extinguisher with mounting bracket? Capacity lbs

(i) A self-recovery winch? ; If yes:

1) Manufacturer , Model

2) 12,000 lb minimum capacity (first layer)?

3) 80 ft minimum cable length?

4) A remote control to operate winch functions outside the vehicle?

5) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) listing all of the features found on a winch of this type must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

(j) Language requirements:

1) Are all instructions, diagrams, and warning labels on the vehicle in English, or universal symbols?

2) Is a vehicle operator’s manual provided for each vehicle, written in English?

3) Does the operator’s manual for each vehicle have an amendment stating the ability of the vehicles engine to operate on 500 ppm sulfur diesel fuel?

Comments

4. RATING

(a) Are the vehicle ratings the manufacturer’s published ratings at the time of offer?

(b) Do any of the component ratings exceed the manufacturer’s published ratings?

Comments

5. ENGINE

(a) Can the vehicle be operated long-term on 50 ppm sulfur diesel fuel?

1) Manufacturer , Model , Year , Type

2) Number of cylinders , Displacement cubic inches

3) Max net power hp @ rpm; Max net torque ft-lbs @ rpm

(b) What Euro Standard does this engine meet?

(c) Are the cooling system and air filter for the engine designed for a hot, dusty environment, 120°F?

Comments

6. CHASSIS/DRIVELINE/AXLES/SUSPENSION

(a) Chassis: Manufacturer , Model , Year , Configuration

1) SUPPORTING DOCUMENTATION REQUIRED: Provide brochures/drawings/dimensioned schematics and photographs of the truck chassis. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

DRIVELINE/AXLES

(b) Front: Manufacturer , Model , Load rating lbs

(c) Rear: Manufacturer , Model , Load rating lbs

(d) Drive axle gear ratio

(e) Is a locking or limited slip differential provided on the rear axle?

1) If yes, check appropriate box: Locking |_| Limited-slip |_|

SUSPENSION

(f) Are the springs, shocks and axles provided the heaviest-duty available for this size vehicle?

(g) Front: Type , Load rating lbs

(h) Rear: Type , Load rating lbs Comments

7. WEIGHTS (pounds) AND DIMENSIONS (inches)

(a) Curb weight

(b) Maximum capacity of 20 persons as payload at GVW 3,500 lbs

(c) Weight of crew 350 pounds

(d) Additional payload (if applicable)

(e) GVW (total of (a), (b), (c), and (d) above)

DIMENSIONS

(f) Wheelbase

(g) Track (widths from center-to-center of tires): Front , Rear

(h) Ground clearance

(i) Distance from ground to cargo body floor

(j) Overall Dimensions: Length , Width (excluding mirrors) , Height Comments

8. TRANSMISSION

(a) Manufacturer , Model , Type

(b) Number of speeds: Forward Reverse

(c) Is a 2-speed transfer case provided?

Comments

9. STEERING

(a) Is the vehicle equipped with tilt, power steering, and right-hand drive (RHD)?

Comments

10. ELECTRICAL

(a) Electrical and starting system volts

(b) Are heavy duty, maintenance free batteries provided?

1) Number of batteries provided?

(c) Alternator output amps Comments

11. WHEEL ASSEMBLY (TIRE AND WHEEL)

(a) Are all tires tubeless radials?

1) Manufacturer , Model

2) Size and load rating: Front Rear Spare

3) Tread design: Front , Rear , Spare

(b) Are all tires, including the spare, the same size, load rating and tread design?

(c) Are all wheel assemblies interchangeable, including spare?

Comments

12. PERFORMANCE

(a) What is the minimum temperature the vehicle can be stored, started and operated in? °F

(b) What is the maximum temperature the vehicle can be stored, started and operated in? °F

(c) What is the maximum grade (% slope) the parking brake will hold the vehicle at GVW? %

(d) Is the vehicle capable of maintaining a minimum speed of 55 mph (88 kph) while driving on a level highway, at GVW?

(e) What is the range, at GVW, on a level highway surfaces? miles at mph Comments

13. CAB

(a) Type

(b) Are heavy duty heating, defrosting, and air conditioning systems provided, suitable for operation in a hot, dry environment (120°F)?

Comments

14. GAME VIEWER BODY

(a) Is the game viewer body a rear seating area with a half-wall around its perimeter, windowless but open with only structural uprights to support the roof, which covers the entire seating area?

1) SUPPORTING DOCUMENTATION REQUIRED: Provide brochures/drawings/dimensioned schematics and photographs of the game viewer body. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

(b) Does the game viewer body have seating for 20 passengers?

(c) Are the seats:

1) Vinyl upholstered?

2) Equipped with magazine pockets in the backs or sides?

3) Equipped with lap-type seat belts?

(d) Are roll-down canvas flaps installed on the sides of the game viewer body roof?

(e) Is at least one side entrance with a step(s) provided on the game viewer body?

(f) Is a slanted, non-slip, rubberized floor provided in the game viewer body?

(g) Is a stowage box with rear access installed at the rear of the game viewer body?

1) Is the stowage box securable by an included padlock, with two keys?

(h) Is lighting provided in the game viewer body capable of illuminating the entire seating area?

Comments

15. COLOR

(a) Is the exterior color of the vehicle Mala Green, or the manufacturer’s closest equivalent?

Comments

17. CORROSION PROTECTION

(a) Is the entire vehicle, where applicable (including the seating area and roof support structure) coated with Carwell (www.carwell.com) type of corrosion protection to prevent corrosion and rust due? , if yes describe application process:

(b) If the vehicle is not coated with Carwell, is it coated with an equivalent type of protection? , if yes what type of protection is provided?

(c) Are different types of corrosion protection used on different parts of the vehicle? , describe Comments

18. RADIO FREQUENCY IDENTIFICATION (RFID) TAGS:

(a) Is each vehicle or item and associated lot of spares tagged with a removable active RFID tracking tag? Manufacturer Model

(b) Where is the RFID tag located on the vehicle or item and associated lot of spares?

(c) How is the tag affixed to the vehicle or item and associated lot of spares?

(d) Will the tag’s electronic format be in compliance with the Joint Total Asset Visibility (JTAV) version 2.0 specifications, section 3.4.1 format?

1) Which company or agency will “write to” or “program” the tag?

Comments

SOURCE SELECTION SENSITIVE, SEE FAR 3.104