Attachment_0002_-_TIQ_-_Dump_Truck,_15_Yard_-_Serbia.doc

Solicitation Attachment 0002 Technical Information Questionnaire (TIQ)

April, 2017

FAILURE TO PROVIDE ALL OF THE INFORMATION REQUIRED BELOW MAY RENDER YOUR PROPOSAL INELIGIBLE FOR AWARD

DUMP TRUCK, 15 YD3

The purpose of this questionnaire is to determine the suitability of your equipment to satisfy the requirements as stated in the specification. YOU MUST PROVIDE A RESPONSE TO ALL QUESTIONS. Failure to provide a response may result in the rejection of your proposal.

Units: The data provided in the TIQ is to be provided in English units, unless otherwise specified. Metric units may be provided if clearly defined and identified.

All written information is to be in English.

In addition to responding to the questions below, the offeror shall provide the following:

(a) Vehicle and major component commercial literature and or specification sheets or any other information that would substantiate the information provided. If your commercial literature does not provide information relating to a particular question, you are required to provide a written explanation of your ability to meet that particular requirement with your written proposal. Where indicated herein, supporting documentation must be provided along with the location of that information stated (e.g. page number, paragraph, etc.).

1) Supporting documentation is required, see paragraphs: 1(b)2, 4(a)1, 9(b)1, and 14(a)2.

(b) Identification of all modifications or redesigns to the previously manufactured base vehicle necessary to meet the requirements of the specifications. The offeror shall also explain in detail the reasons for the modifications or redesigns.

Information Notes:

(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number shall be shown.

(b) Curb weight shall be weight of vehicle offered, completely equipped with coolant, fuel and lubricants, less the weight of the crew (driver and passenger (350 lbs)).

(c) Gross Vehicle Weight (GVW) shall include curb weight of the vehicle, weight of the crew (350 lbs), and full payload in dump body. Weight distribution loaded shall be based on GVW.

GENERAL INFORMATION REQUIRED

Personnel Responding to Questionnaire:

(a) Name

(b) Job Title

(c) Company Name

(d) Telephone and Fax Numbers

(e) E-mail address

(f) Mailing Address

(g) Company Website Comments

DUMP TRUCK, 15 YD3

1. CONFIGURATION

(a) Is the vehicle a Dump Truck, 6x6, 2017 model year or later? FORMDROPDOWN

(b) Is the Dump Truck capable of safely loading, transporting, and dumping 15 yd3 of material? FORMDROPDOWN

1) Base vehicle and chassis: Manufacturer

2) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) listing all the main features found on the base vehicle and chassis must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

(c) Has the vehicle been provided with all new parts? FORMDROPDOWN

Comments

2. EQUIPMENT

Is the vehicle equipped with: (yes or no and briefly expand in comment section, as needed)

(a) Exterior lighting package including headlights, taillights, brake lights, turn signals, back-up lights, and daytime running lights? FORMDROPDOWN

1) Do all forward facing lights have road debris protection on them? FORMDROPDOWN

(b) Vehicle dash instrumentation display in metric? FORMDROPDOWN

(c) Lockable tool box(es) or secured storage compartment(s)? FORMDROPDOWN If yes, describe

1) Number of compartments Dimensions (inches): Height Length Depth

2) Is the compartment(s) lockable? FORMDROPDOWN If yes:

(i) If more than one compartment is provided, are all compartment locks identically keyed? FORMDROPDOWN

3) Is there sufficient capacity to store all provided equipment and accessories? FORMDROPDOWN

4) Are the following tools and accessories provided in the storage compartments:

(i) Standard tools required for simple operator level maintenance? FORMDROPDOWN

FORMCHECKBOX

Wrench and socket set, FORMCHECKBOX Screwdrivers, FORMCHECKBOX Adjustable wrench, FORMCHECKBOX Pliers, FORMCHECKBOX

Hammer, other tools (list)

(ii) Tire inflating hose with pressure gauge and quick-connect fittings on both ends? FORMDROPDOWN If yes, is the hose powered by the vehicle’s compressed air system and of sufficient length to inflate all tires on the vehicle? FORMDROPDOWN

(d) Front and rear steel bumpers? FORMDROPDOWN If yes, thickness of steel used inch

(e) Rear tires covered by dump body structure? FORMDROPDOWN ; Rubber mud flaps behind rear-most tires? FORMDROPDOWN

(f) Front tow hooks? FORMDROPDOWN Quantity

Comments

3. RATINGS

(a) Have any of the component ratings been raised to meet the requirements? FORMDROPDOWN

Comments

4. ENGINE

(a) Is the vehicle provided with a low-sulfur diesel engine, capable of long-term operation on the diesel fuel available in Serbia? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) for the engine must be provided. State where this is provided in your proposal (e.g. page number, paragraph, etc.)

(b) Manufacturer Model Model Year

(c) Maximum power rating hp @ rpm; Maximum torque rating ft-lbs @ rpm

(d) Cold weather package for engine operation:

1) Is an engine block heater provided? FORMDROPDOWN If yes, Manufacturer Model

2) Is a heated fuel and water separator provided? FORMDROPDOWN If yes, Manufacturer Model

3) Is a fuel heater installed in the fuel tank or in the fuel line as close to the tank as practical? FORMDROPDOWN If yes, Manufacturer Model

4) Is a fuel-fired heater plumbed in with the engine coolant? FORMDROPDOWN If yes, Manufacturer Model Comments

5. DRIVELINE AND FRAME

(a) What is the vehicle driveline configuration? FORMDROPDOWN

AXLES

(b) Front: Manufacturer Model Load rating lbs

(c) 1st rear axle: Manufacturer Model Load rating lbs

(d) 2nd rear axle: Manufacturer Model Load rating lbs

(e) Is a rear axle provided with lockable or limited-slip differential? FORMDROPDOWN If lockable, how is it engaged? (describe) CHASSIS DIMENSIONS (inches, unless otherwise labeled)

(f) Yield strength of frame rails

(g) Dimensions of frame rails:

(h) Resistance Bending Moment (RBM) of each frame rail

(i) Is a single or double frame rail provided? FORMDROPDOWN

(j) Wheelbase

(k) Track (widths from center-to-center of tires): Front

(l) Ground clearance WEIGHTS (see Informational Notes on first page) (in pounds) Note: The axles are numbered from the front of the vehicle to the rear.

(m) Curb weight (chassis and empty dump body)

(n) Weight of crew members including driver (2 x 175 lbs) = 350

(o) Payload (full dump body weight)

(p) GVW (total of (m), (n) and (o))

(q) Weight distribution:

1) Weight distribution at GVW, front axle

2) Weight distribution at GVW, first rear axle

3) Weight distribution at GVW, second rear axle

4) Loaded, total (must equal (p) above) Comments

6. TRANSMISSION

(a) Type FORMDROPDOWN Manufacturer Model

(b) Is a two-speed transfer case also provided? FORMDROPDOWN If yes, what ratio?

Comments

8. BRAKES

(a) Service brakes: Type Front Rear

(b) Is the vehicle provided with an engine brake? FORMDROPDOWN

Comments

9. WHEEL ASSEMBLY (TIRE AND WHEEL)

(a) Are all tires, including the spare, radials with the same radial tires rated for mud and snow? FORMDROPDOWN

(b) Tires: Manufacturer Model Size and load rating

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) listing load rating, tire design, etc. must be provided. State where this is in your proposal (e.g. page no., paragraph, etc.)

(c) Wheels: Manufacturer Model Size and load rating

Comments

10. ELECTRICAL

(a) Is an amber rotating beacon, LED, or strobe-type warning light bar installed on top of the cab? FORMDROPDOWN If yes, Type Manufacturer Model

(b) Additional lighting for off-highway, night-time dumping operations:

1) Is an off-road LED light bar mounted on top-center of front bumper? FORMDROPDOWN If yes, Manufacturer Model Rating lumens

2) Are LED lights mounted at the rear of dump body sufficient to illuminate the dumping area? FORMDROPDOWN If yes, Manufacturer Model Rating lumens Comments

11. PERFORMANCE

(a) What are the minimum and maximum temperatures the vehicle can be stored, started, and operated in? Minimum (F Maximum (F

(b) Does the vehicle have a minimum 70 gallon fuel tank? FORMDROPDOWN

Comments

12. COLOR

(a) Is the exterior color of the vehicles cab and entire dump body Army Green 491, color chip 24070, in accordance with FED-STD-595C, or the manufacturer’s closest equivalent? FORMDROPDOWN

Comments

13. CAB

(a) Is an air or hydraulically dampened driver seat and fixed passenger seat provided? FORMDROPDOWN

(b) Are heated, flat, primary side-view mirrors provided on exterior of cab, with left-hand and right-hand convex mirrors mounted near them? FORMDROPDOWN

(c) Are left and right side grab handles provided for exterior of cab? FORMDROPDOWN

(d) Is the heating, defrosting and air conditioning systems the manufacturer’s heaviest duty systems? FORMDROPDOWN

Comments

14. Dump Body

(a) Does the vehicle have a 15 yd3 dump body with a dump angle of approximately 45(?

1) Dump body: Manufacturer Model

2) SUPPORTING DOCUMENTATION REQUIRED: Exterior photographs, computer aided drawings (CAD), or concept sketches of the dump body, along with brochures, specification sheet(s) and all relevant supplemental information must be provided for this item. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

(b) Is the dump body payload capacity at least 2,400 lbs per yd3?

(c) Does the dump body have:

1) Sides, front wall, floor, and spreader apron made from ¼ inch AR400 steel?

2) Front-mounted telescopic hoist with dog house?

3) Air-operated tail gate latches?

4) 1/2 cab guard?

5) Heavy-duty rear hinges with greaseable and removable pins?

6) PTO with heavy-duty, hydraulic pump?

7) Ladders permanently attached on both sides?

8) Body up safety prop and indicator light?

9) LED lighting, reflectors and conspicuity striping installed per DOT?

10) Rear butt plate with: A pintle hook? A 7-pin connector?

Glad hands? Two D-rings?

Comments

15. RADIO FREQUENCY IDENTIFICATION (RFID) TAG

(a) Is each vehicle or item and associated lot of spares tagged with a removable active RFID data rich tracking tag? If yes, Manufacturer FORMTEXT

Model FORMTEXT

(b) Will the tag’s electronic format be in compliance with the JTAV version 2.0 specifications, section 3.4.1 format?

1) Which company or agency will “write to” or “program” the tag?

Comments

SOURCE SELECTION SENSITIVE, SEE FAR 3.104