TIQ_-_Crash_Rescue_Vehicle_2016.doc

Solicitation

Attachment 0006 Technical Information Questionnaire (TIQ)

June 2016

FAILURE TO PROVIDE ALL OF THE INFORMATION REQUIRED BELOW MAY RENDER YOUR PROPOSAL INELIGIBLE FOR AWARD

CRASH RESCUE VEHICLE, AIRPORT

The purpose of this questionnaire is to determine the suitability of your equipment to satisfy the requirements as stated in the specification. YOU MUST PROVIDE A RESPONSE TO ALL QUESTIONS, BLANKS, AND REQUIRED SUPPPORTING DOCUMENTATION REFERENCES. IF ANY OF YOUR ANSWERS REQUIRE FURTHER EXPLANATION, YOU MUST ALSO INCLUDE THAT IN THE APPLICABLE COMMENT SECTION. Failure to provide a response may result in the rejection of your proposal.

Units: The data provided in the TIQ is to be provided in English units, unless otherwise specified. Metric units may be provided if clearly defined and identified.

All written information is to be in English.

In addition to responding to the questions below, the offeror shall provide the following:

(a) Supporting documentation is required, see paragraphs 2(a)(1), 2(d)(7), 2(f)(1), 4(a)(1), 9(a)(1), 10(c)(3), 10(d)(3), 14(a), 14(e)(2)(iv), 15(a)(6), 15(b)(6), 15(c)(8), 15(d)(6), 15(e)(4), and 15(g)(5).

(b) Identification of all modifications or redesigns to the previously manufactured base vehicle necessary to meet the requirements of the specifications. The Offeror shall also explain in detail the reasons for the modifications or redesigns.

(c) US Federal Motor Vehicle Safety Standards (FMVSS) can be obtained at the following website: http://www.access.gpo.gov/nara/cfr/waisidx_04/49cfr571_04.html

INFORMATION NOTES

(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number shall be shown.

(b) Curb weight shall be weight of vehicle offered, completely equipped with coolant, fuel and lubricants, less the weight of the crew (driver and 3 crew (700 pounds)).

(c) Gross Vehicle Weight (GVW) shall include curb weight of the vehicle, weight of the driver and 3 crew (700 pounds), and a full payload of equipment.

(d) Gross Vehicle Weight Rating (GVWR) shall be the maximum allowable total weight of the vehicle including curb weight, and maximum payload.

CRASH RESCUE VEHICLE, AIRPORT

GENERAL INFORMATION

Personnel Responding to Questionnaire:

(a) Name

(b) Job Title FORMTEXT

(c) Company Name FORMTEXT

(d) Telephone and Fax Numbers FORMTEXT

(e) E-mail address FORMTEXT

(f) Mailing Address FORMTEXT

(g) Company Website FORMTEXT

Comments FORMTEXT

1. CONFIGURATION

(a) Is the vehicle been provided with all new parts? FORMDROPDOWN

(b) Is the vehicle a 2016 model year or later? FORMDROPDOWN

(c) Is the vehicle provided an airport Crash Rescue Vehicle (Rapid Intervention Vehicle (RIV))? FORMDROPDOWN

1) Is the vehicle a pickup-based 4 door, with single front tires and double rear tires (dually rear axle configuration)? FORMDROPDOWN

2) Manufacturer

3) Model

(d) Is the vehicle capable of rapid arrival to airport crash scenes, providing firefighting and victim rescue capabilities? FORMDROPDOWN

(e) Does the vehicle have less than 100 miles (160 km) on the odometer? FORMDROPDOWN

(f) Does the vehicle comply with the International Civil Aviation Organization (ICAO) standards applicable to your proposal? FORMDROPDOWN Comments

2. EQUIPMENT

Is the vehicle equipped with the following (yes or no, and briefly expand in comment section, as needed):

(a) All of the standard equipment found on a pickup-based 4-door truck of this make and model? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) listing all standard equipment found on a pickup-based 4-door truck of this make and model must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) Lockable toolbox(es) or stowage compartment(s) for storage of items listed in question “c” below? FORMDROPDOWN Number of tool boxes Location of toolbox(es) or stowage compartment(s) Maximum width of toolbox(es) or stowage compartment(s)? inch

1) Is the toolbox(es) or stowage compartment(s) environmentally sealed? FORMDROPDOWN

2) Is the toolbox(es) or stowage compartment(s) identically keyed for all vehicles? FORMDROPDOWN

3) How many keys are provided with each vehicle?

(c) Are the following items provided?

1) FORMCHECKBOX

Standard tools for simple operator level maintenance:

(i) FORMCHECKBOX Wrench FORMCHECKBOX Socket set FORMCHECKBOX Screwdrivers FORMCHECKBOX Adjustable wrench FORMCHECKBOX Pliers FORMCHECKBOX Hammer FORMCHECKBOX Others

2) FORMCHECKBOX

Tire changing tools; Describe

3) FORMCHECKBOX

Lifting jack; capacity tons

4) FORMCHECKBOX

Portable air compressor

5) FORMCHECKBOX

Tire inflating hose with quick-connect fittings on both ends;

(i) Is the hose of sufficient length to inflate all tires on vehicle? FORMDROPDOWN

6) FORMCHECKBOX

Chuck

(i) Is the chuck capable of filling the inner rear tires as well as the other tires on the vehicle?

7) FORMCHECKBOX

Pressure gauge

(d) Is the vehicle equipped with a self-recovery winch? FORMDROPDOWN ; If yes, does the winch have the following characteristics:

1) A 12,000 lb (5,443 kg) capacity (first layer)? FORMDROPDOWN

2) A 100 foot (30.5 m) cable length minimum? FORMDROPDOWN

3) A 50% cable safety factor? FORMDROPDOWN

4) A roller fairlead? FORMDROPDOWN

5) Mounted to front bumper? FORMDROPDOWN

6) The ability to operate outside of vehicle with remote control? FORMDROPDOWN

7) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(e) Are the front and rear wheels provided with anti-sail mud flaps? FORMDROPDOWN

(f) Is the vehicle equipped with a combination bull bar or brush guard? FORMDROPDOWN , if yes describe FORMTEXT

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(g) Is the vehicle provided with two front and two rear frame-mounted tow hooks or eyes? FORMDROPDOWN

(h) Language requirements:

1) Are all instructions, diagrams, and warning labels bilingual in both Bulgarian and English or universal symbols? FORMDROPDOWN

(i) Are they permanently affixed to the vehicle? FORMDROPDOWN

2) Are fuel filler caps (or an area close to the filler door) provided with labels stating type of fuel that is compatible with the vehicle in both Bulgarian and English or universal symbols? FORMDROPDOWN

3) Are manuals provided for each vehicle written in both Bulgarian and English? FORMDROPDOWN

Comments

3. RATINGS, WEIGHTS, AND DIMENSIONS

(a) Are the vehicle ratings the manufacturer’s published ratings at the time of offer? FORMDROPDOWN

(b) Do all individual component ratings meet or exceed the requirements? FORMDROPDOWN

(c) Gross Vehicle Weight Rating (GVWR) pounds

Comments

WEIGHTS (pounds)

(d) Curb weight

(e) Weight of operator and 3 passengers 700 lbs

(f) Payload (fully loaded with equipment)

(g) GVW (total of (d), (e), and (f))

Comments

DIMENSIONS (inches)

(h) Wheelbase

(i) Ground clearance Comments

4. CHASSIS

(a) Chassis manufacturer Model

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) What is the vehicle driveline configuration? FORMCHECKBOX 4x2 FORMCHECKBOX 4x4 Other

(c) Rear axle configuration FORMDROPDOWN

(d) Is a rear locking or limited slip differential provided on the rear axle? FORMDROPDOWN

1) How are locking differentials engaged (if provided, please describe)?

2) Does the rear locking differential engage automatically or by the driver without leaving the driver’s position? FORMDROPDOWN

Comments

5. ENGINE

(a) Manufacturer

(b) Number of cylinders

(c) Net power at engine governed speed

(d) Maximum net torque

(e) Can the engine operate as required in the specification on the fuel available in Bulgaria? FORMDROPDOWN

(f) Provide description of cooling system

(g) Describe air filtration system Comments

6. TRANSMISSION

(a) What type of transmission is provided? FORMDROPDOWN

1) Manufacturer Model

2) Number of speeds: Forward Reverse Comments

7. STEERING

(a) Is the vehicle left-hand drive? FORMDROPDOWN

(b) Is the vehicle equipped with power steering? FORMDROPDOWN

Comments

8. BRAKES

(a) Service brakes: Type Front Rear

1) Are the service brakes provided with an Anti-lock Brake System (ABS)? FORMDROPDOWN

Comments

9. WHEEL ASSEMBLY (TIRE AND WHEEL)

(a) Tires: Manufacturer

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) Are all tires tubeless, on-off road radials? FORMDROPDOWN

(c) Are all tires, including spare, the same size, load rating and tread design? FORMDROPDOWN

(d) Are all wheels, including the spare, interchangeable? FORMDROPDOWN

(e) Is a full size spare tire and wheel assembly with holder provided? FORMDROPDOWN

1) Storage location of spare on vehicle Comments

10. ELECTRICAL SYSTEM

(a) Is the vehicle provided with the chassis OEM’s heaviest-duty alternator? FORMDROPDOWN , Output amps

(b) Are dual, heavy-duty batteries provided? FORMDROPDOWN

1) Are the batteries maintenance-free? FORMDROPDOWN

2) CCA each

(c) Is the vehicle equipped with either a light bar or beacons? FORMDROPDOWN , if yes:

1) If a light bar is provided:

(i) Manufacturer

(ii) Model

(iii) Color(s)

(iv) Location

(v) Number of lights

(vi) Is the light bar permanently mounted to vehicle?

2) If beacons are provided:

(i) Manufacturer

(ii) Model

(iii) Color(s)

(iv) Locations

(v) Number of beacons

(vi) Are the beacons permanently mounted to vehicle?

3) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for either the light bar or beacons. State where this is provided in your proposal (e.g. page number and paragraph)

(d) Is the vehicle provided with a siren and a Public Address (PA) system?

1) Manufacturer

2) Model

3) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(e) Is the vehicle provided with back-up lights and an alarm? FORMDROPDOWN

(f) Is a dedicated 20 amp circuit for radio communications equipment provided in the cab of the vehicle? FORMDROPDOWN

(g) Does the vehicle have shoreline hookup capability? FORMDROPDOWN ; If so:

1) Does the vehicle have cab and compartment receptacles equipped with shore power? FORMDROPDOWN

(h) Is the vehicle equipped with the appropriate battery chargers necessary for all the battery powered equipment and tools? FORMDROPDOWN

Comments

11. PERFORMANCE

(a) What are the minimum and maximum ambient temperatures the vehicle can be stored, started, and operated in? Minimum ˚F, Maximum ˚F

(b) Is the vehicle capable of operating 40% of mission on sandy roads and trails, 50% on paved roads, and 10% off-road? FORMDROPDOWN

Comments

12. COLOR AND DECALS

(a) Is the color of the vehicle (including, at a minimum, the cab) Red, FED-STD-595 color chip 11105 or the manufacturer’s closest equivalent? FORMDROPDOWN

(b) Are decals saying “RESCUE” located on both the sides of the cab and either the hood or roof of the vehicle? FORMDROPDOWN

1) What language of the word “RESCUE” are the decals?

Comments

13. CAB

(a) Type

(b) Seating capacity

(c) Is the heating and defrosting system the manufacturer’s heavy-duty system? FORMDROPDOWN

(d) Is the air conditioning system the manufacturer’s heavy duty system? FORMDROPDOWN

Comments

14. BODY AND FIRE-FIGHTING SYSTEM

(a) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a schematic showing the vehicle body and equipment layout, design, and storage details must be provided. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

(b) Body requirements:

1) Are external storage compartments provided with roll-up doors on both sides of the vehicle for equipment storage? FORMDROPDOWN ; If so, are the compartments:

(i) Lighted? FORMDROPDOWN

(ii) Water-resistant? FORMDROPDOWN

(iii) Provided with multiple shelving and equipment mounts? FORMDROPDOWN

(iv) Lockable, and identically keyed for all vehicles? FORMDROPDOWN ; With a minimum of 4 keys provided? FORMDROPDOWN

(c) Are work-scene lights mounted on the body for nighttime operations? FORMDROPDOWN ; How many? , Locations

(d) Is a roof-access ladder permanently mounted onto the back or side of the body? FORMDROPDOWN

(e) Fire-fighting system minimum requirements:

1) Are tanks provided on the vehicle for:

(i) Water? FORMDROPDOWN ; If yes, volume gallons

(ii) Foam? FORMDROPDOWN ; If yes, volume gallons

2) Is an onboard centrifugal pump provided? FORMDROPDOWN ; If so:

(i) How is the pump driven? FORMDROPDOWN

(ii) Is it rated at a minimum of 250 GPM? FORMDROPDOWN

(iii) Does it provide the vehicle with pump and roll capability? FORMDROPDOWN

(iv) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the pump and its power source. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

3) Is the vehicle equipped with a bumper-mounted monitor, powered by the pump, for propelling water and foam? FORMDROPDOWN

4) Is a fire hose provided, capable of manually dispensing water and foam? FORMDROPDOWN ; If yes,

(i) How long is the hose? ft

(ii) Is a reel provided, with power rewind? FORMDROPDOWN

(f) Controls:

1) Are all controls and control panels in lighted enclosures or individually lit for nighttime operations? FORMDROPDOWN

2) Are all controls marked in Bulgarian and English, or labeled in universal symbols? FORMDROPDOWN

Comments

15. MOBILE FIRE-FIGHTING AND RESCUE EQUIPMENT

Is the Crash Rescue Vehicle provided with the following equipment and the appropriate space for stowage:

(a) A rescue disc saw? FORMDROPDOWN with:

1) A rotary blade suitable for cutting through aluminum and other aircraft metals? FORMDROPDOWN

2) A 2-stroke engine, fueled by premixed gas and oil? FORMDROPDOWN

3) A gas can labeled “Premixed Gas and Oil” in Bulgarian and English, for extra fuel? FORMDROPDOWN

4) Extra blades? FORMDROPDOWN ; If so, how many

5) Dedicated stowage compartment(s) on the vehicle for the saw, gas can, and extra blades? FORMDROPDOWN

6) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the saw. State where this is provided in your proposal (e.g. page number and paragraph) Comments

(b) A combination tool? FORMDROPDOWN with:

1) Cutting and spreading capabilities? FORMDROPDOWN

2) A maximum cutting opening of at least 6 inches? FORMDROPDOWN

3) A maximum spreading distance of at least 10 inches? FORMDROPDOWN

4) A self-contained and portable system? FORMDROPDOWN

5) How is it powered?

6) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the combination tool. State where this is provided in your proposal (e.g. page number and paragraph) Comments

(c) A telescopic ram? FORMDROPDOWN ; If so:

1) What is its minimum retracted length?

2) What is its maximum extended length?

3) Is it a self-contained and portable system? FORMDROPDOWN

4) What powers the hydraulics?

5) Are the hydraulic hose(s) NFPA conforming? FORMDROPDOWN

6) What is the length of the hydraulic hose(s)?

7) Are there quick connectors on each end of the hose(s)? FORMDROPDOWN

8) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the ram. State where this is provided in your proposal (e.g. page number and paragraph) Comments

(d) A ladder? FORMDROPDOWN ; If so:

1) What material is the ladder made from? FORMDROPDOWN

2) What type of ladder is it? FORMDROPDOWN

3) Minimum folded or retracted length

4) Weight

5) Are there provisions for stowing the ladder on the roof of the body? FORMDROPDOWN ; if so, describe

6) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the ladder. State where this is provided in your proposal (e.g. page number and paragraph) Comments

(e) Two mobile scene lights? FORMDROPDOWN ; If so:

1) Are they LED type lights? FORMDROPDOWN

2) How are the lights powered? FORMDROPDOWN

3) Are they mounted on telescoping stands? FORMDROPDOWN

4) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the scene lights. State where this is provided in your proposal (e.g. page number and paragraph) Comments

(f) SCBA gear sets? FORMDROPDOWN ; If so:

1) How many sets?

2) How many tanks total are provided?

(i) What is the capacity of each tank?

3) Are the sets complete with:

(i) Breathers? FORMDROPDOWN

(ii) Regulators and hoses? FORMDROPDOWN

(iii) Harnesses and mounting plates? FORMDROPDOWN

Comments

(g) A high-pressure lifting bag? FORMDROPDOWN ; If so:

1) Can it be filled by SCBA tanks? FORMDROPDOWN

2) Maximum height deflated

3) Minimum height inflated

4) Maximum lifting force

5) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the lifting bag. State where this is provided in your proposal (e.g. page number and paragraph) Comments

(h) A medical first aid kit? FORMDROPDOWN ; If so, does it include:

1) A burn kit? FORMDROPDOWN

2) Two oxygen inhalers? FORMDROPDOWN

3) List all items supplied with the kit Comments

(i) A fire blanket? FORMDROPDOWN ; If so:

1) Is it woolen? FORMDROPDOWN

2) Does it come with a storage pouch? FORMDROPDOWN

(j) One ABC fire extinguisher? FORMDROPDOWN ; If so, capacity lbs

(k) One CO2 fire extinguisher? FORMDROPDOWN ; If so, capacity lbs

(l) Assorted rescue tools, hand tools and equipment including:

1) A rescue grab hook? FORMDROPDOWN ; If so, length ft

2) A seat belt cutter with DZUS key? FORMDROPDOWN ; If so, number of replacement blades

3) Two rescue axes, one small non-wedge type, and one large non-wedge type? FORMDROPDOWN

4) Two crowbars? FORMDROPDOWN ; If so, lengths ft and ft

5) Two lengths of rope, NFPA approved? FORMDROPDOWN ; If so, lengths ft and ft

6) Wire cutters? FORMDROPDOWN

7) Bolt cutters? FORMDROPDOWN

8) Hammer, 4 lb? FORMDROPDOWN

9) Chisel, cold 5/8 inch? FORMDROPDOWN

10) Heavy duty hack saw? FORMDROPDOWN ; If so, number of spare blades

11) Adjustable wrench, 12 inch? FORMDROPDOWN

12) Side cutting pliers, 7 inch? FORMDROPDOWN

13) Slip joint pliers, 10 inch? FORMDROPDOWN

14) Tin snips? FORMDROPDOWN

15) Screwdrivers, 8 piece assorted set? FORMDROPDOWN

(m) Are the instruction diagrams and warning labels for the equipment listed above written in both Bulgarian and English, or in universal symbols? FORMDROPDOWN

Comments

16. RADIO FREQUENCY IDENTIFICATION (RFID) TAGS

(a) Is each vehicle or item and associated lot of spares tagged with a removable active RFID data rich tracking tag? FORMDROPDOWN ; if yes: Manufacturer FORMTEXT

; Model FORMTEXT

(b) Where is the RFID tag located on the vehicle or item and associated lot of spares? FORMTEXT

(c) How is the tag affixed to the vehicle or item and associated lot of spares? FORMTEXT

(d) Will the tag’s electronic format be in compliance with the JTAV version 2.0 specifications, section 3.4.1 format? FORMDROPDOWN

1) Will the Document field be programmed with the document number (e.g. “milstrip”) provided by the government agency? FORMDROPDOWN

2) Will the MISC1 field be programmed with the item serial number, if available? FORMDROPDOWN

3) Will the MISC2 field be programmed or reserved for comments (e.g. contract number)? FORMDROPDOWN

4) Which company or agency will “write to” or “program” the tag? FORMTEXT

Comments FORMTEXT

SOURCE SELECTION SENSITIVE, SEE FAR 3.104