UNIQUE SALIENT CHARACTERISTICS - CUSTOMIZED ENDOSCOPY CARTS.pdf

SPECIFICATIONS – UNIQUE CUSTOMIZATION REQUIREMENTS

Endoscopy Carts:

Metal and curved IV pole (Poles are straight for 15 inches then curves to a right angle for 12 inches then curves again upward for another 12 inches. It has 4 U-shaped hooks attached to the top. Used to support electrical wires, data cables, and medical air.)

IV pole must be capable of holding gas lines and electrical wires out of the procedural fields

Must have a side shelf that cannot be more than 40 inches from the floor. The side shelf must have dimensions of no less than 15 inches x 17 inches

Top of work surface is less than or equal to 46 inches in height (Work surface cannot be more than 46 inches tall)

Must have 3 (wired) storage racks that measure 17.375 x 7.5 x 5 each (2 Storage racks must be attached to the back top of cart using slotted metal brackets. The 3rd shelf must be mounted to the left side as you face the cart. All baskets must be adjustable either in height or sliding them from one side to another.

Must have height adjustable suction cannisters and medical gas mounts. (Suction canisters x 2 are mounted to slotted bracket. Medical gases are mounted to clamp on metal brackets. Bracket length is a minimum of 24 inches.

Tank holders: (E-Tank holder) must be mounted to the right side of cart. Can not be mounted under slide out shelf. Holder must be able to be mounted to front or back of cart on the right side. Must have easy access to removing gas tank when the shelf is fully extended.

Carts SHALL have the following:

• Fully customizable configurations to meet the exact needs of any department or procedure type.

• Shipped fully assembled to customer’s specifications

• Customization of accessories to meet any departmental needs

• A center divider

• A minimum of 4 shelves that are adjustable. Two shelves on each side.

Each shelf must be able to hold a minimum of 125 pounds each. Each side must measure 19.63 inches in width.

• Able to hold Olympus CV-1500 processor (15.6in (w) x 8.58 (h) in x 22.8

(d) inches)

• Able to hold Olympus CV-190 and CLV-190 light source and processor (9.5 (h) in x 15 (w) in x 22 (d) in.

• Medtronic GI Genius 4 in (h) x 15.75 (w) x 20 in (d).

• ERBE flushing pump 6 in (h) x 9 in (w) x 7.5 in (d)

• ERBE Co2 Regulator 6 in (h) x 9 in (w) x 7.5 in (d)

• ERBE Electrosurgical unit 10 in (h) x 16 in (w) x 14 in (d)

• Mounted shelf to left side of cart that can support Biomed Battery Power pack 7 in (h) x 10 in (w) x 18 in (d)

Featherweight III Cart: FWDOUBLEIII BLUE SPECIFICATIONS:

• 1x FWDOUBLEIII BLUE FWIII Double Endoscopy Cart, Blue Bumpers

• 4x Shelf Kit FWIII, Blue

• 2x Power Strip Kit, 6 Outlet, Medical Grade, 15' Cord

• 2x Cord Wrap, Assembly

• 1x Pull Out Keyboard / Laptop Tray, FWIII

• 1x Water Bottle Holder, Deck Mount Kit, FWIII

• 1x Water Bottle Holder, Shelf/Extrusion Mount, FWIII

• 3x Hanging Basket (17.375" X 7.5" X 5") Kit, FWIII

• 1x Accessory Rail Kit, FWIII

• 2x 4" Tank Holder Kit, FWIII

• 1x Front Tank Vertical Accessory Rail Kit, FWIII

• 1x Cord Wrap, Assembly

• 1x Riser Kit, Double, FWIII

• 1x Articulating Monitor Arm (For Riser), 25#, FWIII

• 2x Suction Canister Kit, FWIII

• 1x IV Pole Holder Kit, Extrusion Mount, FWIII

• 1x CORRUGATED, 62 X 32 X 80, (FW DOUBLE)

Healthcare Commercial Grade Double Olympus Endoscopy Carts Salient characteristics to apply to all endoscopy carts.

• Shelf Kit, Blue

• Power Strip Kit

• Cord Wrap, Assembly

• Pull Out Keyboard

• Water Bottle Holder

• Water Bottle Holder

• Hanging Basket

• Accessory Rail

• Tank Holder

• Front Tank Vertical Accessory Rail

• Cord Wrap

• Riser Kit

• Articulating Monitor Arm

• Suction Canister Kit

• IV Pole Holder Kit

• Double Endoscopy Cart