(UNCLASS-DISTR C)_324532033 Rev A_CLB Class Ropeguard Connector Cover_SIGNED SEA.pdf

^UNCLASSIFIED4 3 2 1UNCLASSIFIED UNCLASSIFIED UNCLASSIFIED

PRESERVATION AND PACKAGING NOTESGENERAL NOTES

(NOTES 602 AND 603 ONLY APPLY IF SHIPPED SEPARATELY FROM KIT, REFERENCE 1)

1. THIS DRAWING IS TO BE INTERPRETED IN ACCORDANCE WITH ASME Y14.5-2009.

601. FOLLOWING FINAL MACHINING, SEAL ALL SURFACES, INCLUDING EDGES.APPLY TWOCOATS

OF ITEM 2,EPOXY SEALER, AS FOLLOWS:

A) SURFACE PREPARATION:

I. WIPE THE PART CLEAN USING LINT-FREE RAGS AND ISOPROPYL ALCOHOL OR A

50/50 VOLUMETRIC MIX OF ISOPROPYL ALCOHOL AND POTABLE WATER TO ACHIEVE

AN SSPC-SP 1 CONDITION IAW SSPC-SP 1, "SOLVENT CLEANING".ALLOW 30 MINUTES

FOR THE SOLVENT TO FLASH OFF PRIOR TO PROCEEDING.

II. HAND ABRADE SURFACES WITH 80-120 GRIT SANDPAPER TO REMOVE SURFACE

GLOSS.CARE SHALL BE EXERCISED SO AS NOT TO DAMAGE THE SURFACE.

III. AFTER ABRADING, RE-CLEAN IN ACCORDANCE WITH NOTE 601.A.I.

B) EPOXY SEALER APPLICATION:

I. ITEM 2,EPOXY SEALER, SHALL BE APPLIED ONLY WHEN THE AMBIENT

TEMPERATURE AND THE TEMPERATURE OF THE PREPARED SURFACE ARE BETWEEN

50 DEGREES AND 90 DEGREES FAHRENHEIT AND A MINIMUM OF 5 DEGREES

FAHRENHEIT ABOVE THE DEW POINT.THE MAXIMUMRELATIVE HUMIDITY SHALL BE

80PERCENT.

II. MIX ITEM 2, EPOXY SEALER. AND REDUCE ADMIXED MATERIAL USING ITEM 3, EPOXY

THINNER, IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS.

III. APPLY BASE COAT AND TOP COAT IN ACCORDANCE WITH MANUFACTURER’S

INSTRUCTIONS TO ACHIEVE A TOTAL DRY FILM THICKNESSOF 1.4 TO 2.5 MILS.

ENSURE COMPLETE COVEFfAGE WITH NO HOLIDAYS, NO DRIPS, NO SAGS, OR NO

RUNS.

IV. ALLOW CURING IAW WITH MANUFACTURER'S INSTRUCTIONS (APPROXIMATELY 7

HOURS TO ACHIEVE DRY HARD).

2. UNLESS OTHERWISE NOTED, ALL DIMENSIONS ARE IN INCHES.

3. UNLESSOTHERWISE NOTED,ALL WEIGHTS ARE IN POUNDS.D D

ABBREVIATIONS USED IN THE BODY OF AND NOTES OF THIS DRAWING ARE IN

ACCORDANCE WITH ASME Y14.38-2019, EXCEPT AS SHOWN BELOW:

4.

GRP-GLASS REINFORCED PLASTIC

NEMA-NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION

SSPC-THE SOCIETY FOR PROTECTIVE COATINGS

5. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS DRAWING AND THE

REFERENCES CITED HEREIN, THE TEXT OF THIS DRAWING TAKES PRECEDENCE.

NOTHING IN THIS DRAWINGSHALL SUPERSEDE APPLICABLE LAWS AND

REGULATIONS UNLESS A SPECIFIC EXEMPTIONHAS BEEN OBTAINED.

6. NOTES ON THIS DRAWING ARE DRAWING SPECIFIC.NOTE NUMBERING AND TEXT

DO NOT CONFORM TO ANY PRE-ASSIGNED NOTE NUMBERS OR STANDARD

NOTES DATABASE.

7. REFERENCE DIMENSIONS ARE SHOWN IN PARENTHESES AND ARE PROVIDED FOR

INFORMATION, BUT ARE NOT NECESSARY FOR PROPER FABRICATION AND

INSTALLATION.THESE DIMENSIONS WILL HAVE NO TOLERANCE AND ARE NOT

SUBJECT TO INSPECTION ANDCERTIFICATION.c c602. THE CONTAINER SHALL BE CLEARLY MARKED TO PERMIT THE IDENTIFICATION OF THE

COMPONENT(S) AS FOLLOWS:

A) MANUFACTURE DATE

B) QUANTITY

C) CONTRACT NUMBER

D) DRAWING NUMBER AND REVISION

E) DRAWING TITLE

QUALITY ASSURANCE NOTES

101. THE QUALITY SYSTEM SHALL MEET ISO 9001:2015 OR LATER EDITION. THE SELLER

MAY SUBSTITUTE AN ALTERNATIVE INSPECTION SYSTEM SUBJECT TO APPROVAL BY

NAVSEA 05P3.ISO 9001:2015 DOES NOT APPLY TO PUBLIC NAVY SHIPYARDS WHICH

MUST ADHERE TO NAVSEA TL855-AA-STD-010 (NAVAL SHIPYARD QUALITY

PROGRAMMANUAL).

603. PACKAGE SUCH THAT EACH COMPONENT IS SECURE AND WILL NOT COME IN CONTACT WITH

OTHER PARTS DURING SHIPMENT.SEE CONTRACT FOR ANY ADDITIONAL PACKAGING

REQUIREMENTS.FABRICATION NOTES

201. UNLESS OTHERWISE NOTED:

A) EXTERNAL EDGES SHALL HAVE A RADIUS OF R .01 -.03 OR HAVE A CHAMFER OF.01 -.03 X 45'i10'

B) INTERNAL CORNERS SHALL HAVE A RADIUS OF R .01 -.03

SURFACE ROUGHNESSOF ALL FINAL MACHINED SURFACES SHALL NOT EXCEED 125

MICROINCHES RA.202.

SURFACE SYMBOLS SHALL BE IN ACCORDANCE WITH ASME Y14.36-2018 AND SURFACE

TEXTURE SHALL BE IN ACCORDANCE WITH ASME B46.1-2009.

203.

B B

204. ITEM 1 SHALL BE MACHINED FROM A SOLID SHEET OF GRP, IN ACCORDANCE WITH

NEMA LI 1-1998 OR LATER, GRADE G-10 OR FR-4.

INSPECTION. TOLERANCE. AND TEST NOTES

301. TOLERANCES ARE NOT CUMULATIVE.WHERE TWO OR MORE TOLERANCES CONFLICT THE

CLOSER TOLERANCE SHALL GOVERN.

A CERTIFICATION PACKAGE IS REQUIRED FOR ACCEPTANCE OF EACH COMPONENT.ALL

CERTIFICATIONS SHALL INCLUDE A NAVSEA SERIAL NUMBER FOR TRACEABILITY, BE ON

COMPANY LETTERHEAD, AND CONTAIN THE NAME, TITLE, AND SIGNATURE OF THE

CERTIFYING OFFICIAL.ONE COPY OF THE CERTIFICATION PACKAGE SHALL BE PROVIDED

ELECTRONICALLY TO THE BUYER. THE CERTIFICATION PACKAGE MUST INCLUDE THE

FOLLOWING:

A) A CERTIFICATE OF CONFORMANCE TO THIS DRAWING OR THE APPLICABLE

PROCUREMENT DOCUMENT.

B) MATERIAL CERTIFICATION OF ITEM 1INCLUDING RESULTS OF ALL TESTING IN

ACCORDANCE WITH NEMA LI 1-1998 OR LATER.

C) LIST OF ALL APPLICABLE NAVSEA-APPROVEDWAIVERS AND DEVIATIONS.

302.

A AMARKING NOTES

MARKING OF ITEM 1SHALL BE ENGRAVED OR VIBRO-ETCHED TO A NOMINAL LETTER HEIGHT

OF.25 AND A DEPTH OF.003 TO.025.MARKING INFORMATION TO INCLUDE NAVSEA SERIAL

NUMBER AND DRAWING NUMBER AND REVISION.SEE SHEET 4, ZONE 3C FOR MARKING

LOCATION.

501.

SIZE CAGE NO

D 96169

WBS NAVSEA DRAWING NO REV

A

SCALE CONTRACTOR DWG NO SHEET

NONE 324532033 2

UNCLASSIFIED^4 3 2 1UNCLASSIFIED UNCLASSIFIED UNCLASSIFIED

^UNCLASSIFIED4 3 2 1UNCLASSIFIED UNCLASSIFIED UNCLASSIFIED

4.500 4.500

2X 110.000' -2X 10.000'

2X |5.000' -2X | 5,000' |D D2X | | .030 ABC

-2X | R.700|2X | R.305

^ rT 4X R.25 1.02 r n 2X 4.125 1.020-—MARKING LOCATION

SEE NOTE 501

2X | 9,800 | 2X .75 1.02

2X 2.00 1.02 I I 4.500

I 4- |.04 | A | B~ c c9.000

VIEW 4-2C (4-1A)

r 1|Q |.031A|B | C ~T „ . ^—|Q|,03 | A |B|C

6 4A 0 412.000

B B-| 6,000PARTt C 10.80i.02 2X .25 1.02 X 45' ±5' 2X 2.80 1.02 2X .25 1.02 X 45' *5'

ZA2X R.25 i.02

4.75 1.02 2X R1.50 1.02

2X 3.375 ±.020 I 2X 2.00 ±.02

0 4X R.25 i.02 Q1.02 | J2X .625 1.020 —1 2C

A A A2X 5.25 1.02

SIZE CAGE NO

D 96169

WBS NAVSEA DRAWING NO REVVIEW 4-4A (3-3A> ITEM 1 A

SCALE CONTRACTOR DWG NO SHEET

1:2 324532033 4

UNCLASSIFIED^4 3 2 1UNCLASSIFIED UNCLASSIFIED UNCLASSIFIED

ISO-10303-21;

HEADER;

/* Generated by software containing ST-Developer

* from STEP Tools, Inc. (www.steptools.com) /* OPTION: using custom schema-name function */

FILE_DESCRIPTION(

/* description */ (''), /* implementation_level */ '2;1');

FILE_NAME(

/* name */ '324532033_ROPEGUARD CONNECTOR COVER_REV A_UNCLASSIFIED.stp', /* time_stamp */ '2020-09-28T11:29:35-04:00', /* author */ (''), /* organization */ (''), /* preprocessor_version */ 'ST-DEVELOPER v16.7', /* originating_system */ 'SIEMENS PLM Software NX 12.0', /* authorisation */ '');

FILE_SCHEMA (('AUTOMOTIVE_DESIGN { 1 0 10303 214 3 1 1 1 }'));

ENDSEC;

DATA;

#10=PROPERTY_DEFINITION_REPRESENTATION(#14,#12);

#11=PROPERTY_DEFINITION_REPRESENTATION(#15,#13);

#12=REPRESENTATION('',(#16),#3506);

#13=REPRESENTATION('',(#17),#3506);

#14=PROPERTY_DEFINITION('pmi validation property','',#21);

#15=PROPERTY_DEFINITION('pmi validation property','',#21);

#16=VALUE_REPRESENTATION_ITEM('number of annotations',COUNT_MEASURE(0.));

#17=VALUE_REPRESENTATION_ITEM('number of views',COUNT_MEASURE(0.));

#18=SHAPE_REPRESENTATION_RELATIONSHIP('None', 'relationship between spat2D900662d9o3-None and spat2D900662d9o3-None', #30,#19);

#19=ADVANCED_BREP_SHAPE_REPRESENTATION('spat2D900662d9o3-None',(#40),#3506);

#20=SHAPE_DEFINITION_REPRESENTATION(#21,#30);

#21=PRODUCT_DEFINITION_SHAPE('','',#22);

#22=PRODUCT_DEFINITION(' ','',#24,#23);

#23=PRODUCT_DEFINITION_CONTEXT('part definition',#29,'design');

#24=PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE(' ',' ',#26,

.NOT_KNOWN.);

#25=PRODUCT_RELATED_PRODUCT_CATEGORY('part','',(#26));

#26=PRODUCT('spat2D900662d9o3','spat2D900662d9o3',' ',(#27));

#27=PRODUCT_CONTEXT(' ',#29,'mechanical');

#28=APPLICATION_PROTOCOL_DEFINITION('international standard', 'automotive_design',2010,#29);

#29=APPLICATION_CONTEXT(

'core data for automotive mechanical design processes');

#30=SHAPE_REPRESENTATION('spat2D900662d9o3-None',(#2020),#3506);

#31=PRESENTATION_LAYER_ASSIGNMENT('1','Layer 1',(#40));

#32=STYLED_ITEM('',(#33),#40);

#33=PRESENTATION_STYLE_ASSIGNMENT((#34));

#34=SURFACE_STYLE_USAGE(.BOTH.,#35);

#35=SURFACE_SIDE_STYLE('',(#36));

#36=SURFACE_STYLE_FILL_AREA(#37);

#37=FILL_AREA_STYLE('',(#38));

#38=FILL_AREA_STYLE_COLOUR('',#39);

#39=COLOUR_RGB('Medium Steel',0.596063172350652,0.666666666666667,0.686259250782025);

#40=MANIFOLD_SOLID_BREP('',#41);

#41=CLOSED_SHELL('',(#193,#194,#195,#196,#197,#198,#199,#200,#201,#202,

#203,#204,#205,#206,#207,#208,#209,#210,#211,#212,#213,#214,#215,#216,#217, #218,#219,#220,#221,#222,#223,#224,#225,#226,#227,#228,#229,#230,#231,#232, #233,#234,#235,#236,#237,#238,#239,#240,#241,#242,#243,#244,#245,#246,#247, #248,#249,#250,#251,#252,#253,#254,#255,#256,#257,#258,#259,#260,#261,#262, #263,#264,#265,#266,#267,#268,#269,#270,#271,#272,#273,#274,#275,#276,#277, #278,#279,#280,#281,#282,#283,#284,#285,#286,#287,#288,#289,#290,#291,#292, #293,#294,#295,#296,#297,#298,#299));

#42=SPHERICAL_SURFACE('',#2146,0.25);

#43=SPHERICAL_SURFACE('',#2152,0.25);

#44=CONICAL_SURFACE('',#2128,0.325,45.);

#45=CONICAL_SURFACE('',#2198,0.325,44.9999999999952);

#46=CONICAL_SURFACE('',#2201,0.325,44.9999999999952);

#47=FACE_BOUND('',#509,.T.);

#48=FACE_BOUND('',#510,.T.);

#49=FACE_BOUND('',#512,.T.);

#50=FACE_BOUND('',#513,.T.);

#51=FACE_BOUND('',#517,.T.);

#52=FACE_BOUND('',#518,.T.);

#53=FACE_BOUND('',#519,.T.);

#54=FACE_BOUND('',#520,.T.);

#55=FACE_BOUND('',#537,.T.);

#56=FACE_BOUND('',#538,.T.);

#57=FACE_BOUND('',#543,.T.);

#58=FACE_BOUND('',#544,.T.);

#59=FACE_BOUND('',#556,.T.);

#60=FACE_BOUND('',#557,.T.);

#61=FACE_BOUND('',#561,.T.);

#62=FACE_BOUND('',#562,.T.);

#63=FACE_BOUND('',#563,.T.);

#64=FACE_BOUND('',#564,.T.);

#65=FACE_BOUND('',#565,.T.);

#66=FACE_BOUND('',#566,.T.);

#67=FACE_BOUND('',#567,.T.);

#68=FACE_BOUND('',#568,.T.);

#69=FACE_BOUND('',#569,.T.);

#70=FACE_BOUND('',#570,.T.);

#71=CYLINDRICAL_SURFACE('',#2032,1.5);

#72=CYLINDRICAL_SURFACE('',#2035,1.);

#73=CYLINDRICAL_SURFACE('',#2053,0.25);

#74=CYLINDRICAL_SURFACE('',#2056,0.25);

#75=CYLINDRICAL_SURFACE('',#2059,1.);

#76=CYLINDRICAL_SURFACE('',#2067,0.304999999999999);

#77=CYLINDRICAL_SURFACE('',#2073,0.304999999999999);

#78=CYLINDRICAL_SURFACE('',#2097,1.5);

#79=CYLINDRICAL_SURFACE('',#2098,1.5);

#80=CYLINDRICAL_SURFACE('',#2103,0.7);

#81=CYLINDRICAL_SURFACE('',#2108,0.7);

#82=CYLINDRICAL_SURFACE('',#2117,1.);

#83=CYLINDRICAL_SURFACE('',#2123,0.13);

#84=CYLINDRICAL_SURFACE('',#2124,0.749999999999999);

#85=CYLINDRICAL_SURFACE('',#2125,0.13);

#86=CYLINDRICAL_SURFACE('',#2127,0.305);

#87=CYLINDRICAL_SURFACE('',#2129,0.25);

#88=CYLINDRICAL_SURFACE('',#2130,0.25);

#89=CYLINDRICAL_SURFACE('',#2132,0.25);

#90=CYLINDRICAL_SURFACE('',#2134,0.25);

#91=CYLINDRICAL_SURFACE('',#2135,0.25);

#92=CYLINDRICAL_SURFACE('',#2137,0.25);

#93=CYLINDRICAL_SURFACE('',#2139,0.25);

#94=CYLINDRICAL_SURFACE('',#2140,0.25);

#95=CYLINDRICAL_SURFACE('',#2142,0.25);

#96=CYLINDRICAL_SURFACE('',#2144,0.25);

#97=CYLINDRICAL_SURFACE('',#2148,0.25);

#98=CYLINDRICAL_SURFACE('',#2150,0.25);

#99=CYLINDRICAL_SURFACE('',#2153,0.25);

#100=CYLINDRICAL_SURFACE('',#2171,1.5);

#101=CYLINDRICAL_SURFACE('',#2173,1.);

#102=CYLINDRICAL_SURFACE('',#2174,0.25);

#103=CYLINDRICAL_SURFACE('',#2175,0.25);

#104=CYLINDRICAL_SURFACE('',#2176,0.25);

#105=CYLINDRICAL_SURFACE('',#2177,0.25);

#106=CYLINDRICAL_SURFACE('',#2178,0.25);

#107=CYLINDRICAL_SURFACE('',#2179,0.25);

#108=CYLINDRICAL_SURFACE('',#2181,0.13);

#109=CYLINDRICAL_SURFACE('',#2183,0.13);

#110=CYLINDRICAL_SURFACE('',#2185,0.749999999999998);

#111=CYLINDRICAL_SURFACE('',#2189,0.130000000000001);

#112=CYLINDRICAL_SURFACE('',#2191,0.13);

#113=CYLINDRICAL_SURFACE('',#2193,0.750000000000001);

#114=CYLINDRICAL_SURFACE('',#2197,0.305);

#115=CYLINDRICAL_SURFACE('',#2200,0.305);

#116=B_SPLINE_CURVE_WITH_KNOTS('',3,(#2808,#2809,#2810,#2811,#2812,#2813,

#2814,#2815,#2816,#2817),.UNSPECIFIED.,.F.,.F.,(4,2,2,2,4),(0.,0.25,0.5,

0.75,1.),.UNSPECIFIED.);

#117=B_SPLINE_CURVE_WITH_KNOTS('',3,(#2818,#2819,#2820,#2821,#2822,#2823),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#118=B_SPLINE_CURVE_WITH_KNOTS('',3,(#2827,#2828,#2829,#2830,#2831,#2832),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#119=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3160,#3161,#3162,#3163,#3164,#3165),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#120=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3167,#3168,#3169,#3170,#3171,#3172),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#121=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3213,#3214,#3215,#3216,#3217,#3218,

#3219,#3220,#3221,#3222,#3223,#3224,#3225,#3226,#3227,#3228,#3229,#3230, #3231,#3232,#3233,#3234,#3235,#3236,#3237,#3238,#3239,#3240), .UNSPECIFIED.,.F.,.F.,(4,3,3,3,3,3,3,3,3,4),(0.,0.112617285501672,0.225277981206807, 0.337398370100053,0.449715602808669,0.56231684495568,0.674976085220417, 0.78762449015844,0.900091134950895,1.),.UNSPECIFIED.);

#122=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3242,#3243,#3244,#3245,#3246,#3247,

#3248,#3249,#3250,#3251,#3252,#3253,#3254,#3255,#3256,#3257), .UNSPECIFIED.,.F.,.F.,(4,2,2,2,2,2,2,4),(0.,0.25,0.375,0.5,0.625,0.75, 0.875,1.),.UNSPECIFIED.);

#123=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3259,#3260,#3261,#3262,#3263,#3264,

#3265,#3266,#3267,#3268,#3269,#3270,#3271,#3272,#3273,#3274,#3275,#3276, #3277,#3278,#3279,#3280,#3281,#3282,#3283,#3284,#3285,#3286), .UNSPECIFIED.,.F.,.F.,(4,3,3,3,3,3,3,3,3,4),(0.,0.112286320713137,0.224587994994309, 0.336729942002008,0.449202919423782,0.561848805087659,0.674509649933413, 0.787111912349917,0.89941732372868,1.),.UNSPECIFIED.);

#124=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3287,#3288,#3289,#3290,#3291,#3292),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#125=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3293,#3294,#3295,#3296,#3297,#3298),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#126=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3400,#3401,#3402,#3403,#3404,#3405,

#3406,#3407,#3408,#3409),.UNSPECIFIED.,.F.,.F.,(4,2,2,2,4),(0.,0.25,0.5,

0.75,1.),.UNSPECIFIED.);

#127=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3410,#3411,#3412,#3413,#3414,#3415),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#128=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3416,#3417,#3418,#3419,#3420,#3421),

.UNSPECIFIED.,.F.,.F.,(4,2,4),(0.,0.5,1.),.UNSPECIFIED.);

#129=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3425,#3426,#3427,#3428,#3429,#3430,

#3431,#3432,#3433,#3434),.UNSPECIFIED.,.F.,.F.,(4,2,2,2,4),(0.,0.25,0.5,

0.75,1.),.UNSPECIFIED.);

#130=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3435,#3436,#3437,#3438,#3439,#3440,

#3441,#3442,#3443,#3444),.UNSPECIFIED.,.F.,.F.,(4,2,2,2,4),(0.,0.250000000000001, 0.500000000000001,0.750000000000001,1.),.UNSPECIFIED.);

#131=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3446,#3447,#3448,#3449,#3450,#3451,

#3452,#3453,#3454,#3455),.UNSPECIFIED.,.F.,.F.,(4,2,2,2,4),(0.,0.25,0.5,

0.75,1.),.UNSPECIFIED.);

#132=B_SPLINE_CURVE_WITH_KNOTS('',3,(#3456,#3457,#3458,#3459,#3460,#3461,

#3462,#3463,#3464,#3465),.UNSPECIFIED.,.F.,.F.,(4,2,2,2,4),(0.,0.250000000000001, 0.500000000000001,0.750000000000001,1.),.UNSPECIFIED.);

#133=CIRCLE('',#2024,0.13);

#134=CIRCLE('',#2025,0.750000000000001);

#135=CIRCLE('',#2027,0.750000000000001);

#136=CIRCLE('',#2028,0.130000000000001);

#137=CIRCLE('',#2033,1.);

#138=CIRCLE('',#2034,1.);

#139=CIRCLE('',#2036,0.749999999999998);

#140=CIRCLE('',#2037,0.13);

#141=CIRCLE('',#2039,1.);

#142=CIRCLE('',#2041,1.);

#143=CIRCLE('',#2043,0.25);

#144=CIRCLE('',#2045,1.5);

#145=CIRCLE('',#2047,0.25);

#146=CIRCLE('',#2049,1.5);

#147=CIRCLE('',#2051,0.25);

#148=CIRCLE('',#2054,0.25);

#149=CIRCLE('',#2057,1.);

#150=CIRCLE('',#2058,1.);

#151=CIRCLE('',#2061,0.7);

#152=CIRCLE('',#2062,0.7);

#153=CIRCLE('',#2065,0.304999999999999);

#154=CIRCLE('',#2066,0.304999999999999);

#155=CIRCLE('',#2071,0.304999999999999);

#156=CIRCLE('',#2072,0.304999999999999);

#157=CIRCLE('',#2074,0.25);

#158=CIRCLE('',#2075,0.25);

#159=CIRCLE('',#2077,0.25);

#160=CIRCLE('',#2079,0.25);

#161=CIRCLE('',#2084,1.5);

#162=CIRCLE('',#2087,1.5);

#163=CIRCLE('',#2101,0.7);

#164=CIRCLE('',#2106,0.7);

#165=CIRCLE('',#2115,0.305);

#166=CIRCLE('',#2118,0.325);

#167=CIRCLE('',#2119,0.13);

#168=CIRCLE('',#2120,0.749999999999999);

#169=CIRCLE('',#2121,0.13);

#170=CIRCLE('',#2126,0.305);

#171=CIRCLE('',#2141,0.25);

#172=CIRCLE('',#2143,0.25);

#173=CIRCLE('',#2145,0.25);

#174=CIRCLE('',#2147,0.25);

#175=CIRCLE('',#2149,0.25);

#176=CIRCLE('',#2151,0.25);

#177=CIRCLE('',#2155,0.305);

#178=CIRCLE('',#2164,0.13);

#179=CIRCLE('',#2165,0.749999999999998);

#180=CIRCLE('',#2167,0.305);

#181=CIRCLE('',#2168,1.);

#182=CIRCLE('',#2172,1.);

#183=CIRCLE('',#2180,0.13);

#184=CIRCLE('',#2182,0.13);

#185=CIRCLE('',#2184,0.749999999999998);

#186=CIRCLE('',#2186,0.324999999999994);

#187=CIRCLE('',#2188,0.130000000000001);

#188=CIRCLE('',#2190,0.13);

#189=CIRCLE('',#2192,0.750000000000001);

#190=CIRCLE('',#2194,0.324999999999997);

#191=CIRCLE('',#2196,0.305);

#192=CIRCLE('',#2199,0.305);

#193=ADVANCED_FACE('',(#357),#300,.F.);

#194=ADVANCED_FACE('',(#358),#301,.F.);

#195=ADVANCED_FACE('',(#359),#302,.F.);

#196=ADVANCED_FACE('',(#360),#303,.F.);

#197=ADVANCED_FACE('',(#361),#71,.F.);

#198=ADVANCED_FACE('',(#362),#72,.T.);

#199=ADVANCED_FACE('',(#363),#304,.F.);

#200=ADVANCED_FACE('',(#364),#305,.F.);

#201=ADVANCED_FACE('',(#365),#306,.F.);

#202=ADVANCED_FACE('',(#366),#307,.F.);

#203=ADVANCED_FACE('',(#367),#308,.T.);

#204=ADVANCED_FACE('',(#368),#309,.F.);

#205=ADVANCED_FACE('',(#369),#310,.F.);

#206=ADVANCED_FACE('',(#370),#73,.F.);

#207=ADVANCED_FACE('',(#371),#74,.F.);

#208=ADVANCED_FACE('',(#372),#75,.T.);

#209=ADVANCED_FACE('',(#373),#311,.F.);

#210=ADVANCED_FACE('',(#374),#312,.F.);

#211=ADVANCED_FACE('',(#375),#313,.T.);

#212=ADVANCED_FACE('',(#376),#76,.F.);

#213=ADVANCED_FACE('',(#377),#314,.T.);

#214=ADVANCED_FACE('',(#378),#315,.F.);

#215=ADVANCED_FACE('',(#379),#316,.F.);

#216=ADVANCED_FACE('',(#380),#77,.F.);

#217=ADVANCED_FACE('',(#381),#317,.F.);

#218=ADVANCED_FACE('',(#382),#318,.F.);

#219=ADVANCED_FACE('',(#383),#319,.F.);

#220=ADVANCED_FACE('',(#384),#320,.F.);

#221=ADVANCED_FACE('',(#385),#321,.F.);

#222=ADVANCED_FACE('',(#386),#322,.F.);

#223=ADVANCED_FACE('',(#387),#323,.F.);

#224=ADVANCED_FACE('',(#388),#324,.F.);

#225=ADVANCED_FACE('',(#389),#325,.T.);

#226=ADVANCED_FACE('',(#390),#326,.T.);

#227=ADVANCED_FACE('',(#391),#327,.F.);

#228=ADVANCED_FACE('',(#392),#328,.T.);

#229=ADVANCED_FACE('',(#393),#329,.T.);

#230=ADVANCED_FACE('',(#394),#330,.T.);

#231=ADVANCED_FACE('',(#395),#331,.F.);

#232=ADVANCED_FACE('',(#396),#332,.T.);

#233=ADVANCED_FACE('',(#397),#333,.F.);

#234=ADVANCED_FACE('',(#398),#78,.F.);

#235=ADVANCED_FACE('',(#399),#79,.F.);

#236=ADVANCED_FACE('',(#400),#334,.F.);

#237=ADVANCED_FACE('',(#401),#335,.F.);

#238=ADVANCED_FACE('',(#402),#336,.T.);

#239=ADVANCED_FACE('',(#403),#80,.F.);

#240=ADVANCED_FACE('',(#404),#337,.F.);

#241=ADVANCED_FACE('',(#405),#338,.F.);

#242=ADVANCED_FACE('',(#406),#339,.T.);

#243=ADVANCED_FACE('',(#407),#81,.F.);

#244=ADVANCED_FACE('',(#408),#340,.F.);

#245=ADVANCED_FACE('',(#409),#341,.F.);

#246=ADVANCED_FACE('',(#410),#342,.F.);

#247=ADVANCED_FACE('',(#411),#343,.T.);

#248=ADVANCED_FACE('',(#412),#344,.F.);

#249=ADVANCED_FACE('',(#413),#345,.F.);

#250=ADVANCED_FACE('',(#47,#48),#346,.F.);

#251=ADVANCED_FACE('',(#414),#82,.F.);

#252=ADVANCED_FACE('',(#49,#50),#347,.T.);

#253=ADVANCED_FACE('',(#415),#83,.T.);

#254=ADVANCED_FACE('',(#416),#84,.F.);

#255=ADVANCED_FACE('',(#417),#85,.T.);

#256=ADVANCED_FACE('',(#51,#52),#86,.F.);

#257=ADVANCED_FACE('',(#53,#54),#44,.F.);

#258=ADVANCED_FACE('',(#418),#87,.F.);

#259=ADVANCED_FACE('',(#419),#88,.F.);

#260=ADVANCED_FACE('',(#420),#89,.F.);

#261=ADVANCED_FACE('',(#421),#90,.F.);

#262=ADVANCED_FACE('',(#422),#91,.F.);

#263=ADVANCED_FACE('',(#423),#92,.F.);

#264=ADVANCED_FACE('',(#424),#93,.F.);

#265=ADVANCED_FACE('',(#425),#94,.F.);

#266=ADVANCED_FACE('',(#426),#95,.F.);

#267=ADVANCED_FACE('',(#427),#96,.F.);

#268=ADVANCED_FACE('',(#428),#42,.F.);

#269=ADVANCED_FACE('',(#429),#97,.F.);

#270=ADVANCED_FACE('',(#430),#98,.F.);

#271=ADVANCED_FACE('',(#431),#43,.F.);

#272=ADVANCED_FACE('',(#432),#99,.F.);

#273=ADVANCED_FACE('',(#433),#348,.T.);

#274=ADVANCED_FACE('',(#55,#56),#349,.F.);

#275=ADVANCED_FACE('',(#434),#350,.T.);

#276=ADVANCED_FACE('',(#435),#351,.F.);

#277=ADVANCED_FACE('',(#436),#352,.F.);

#278=ADVANCED_FACE('',(#437),#353,.F.);

#279=ADVANCED_FACE('',(#57,#58),#354,.F.);

#280=ADVANCED_FACE('',(#438),#100,.F.);

#281=ADVANCED_FACE('',(#439),#101,.T.);

#282=ADVANCED_FACE('',(#440),#102,.F.);

#283=ADVANCED_FACE('',(#441),#103,.F.);

#284=ADVANCED_FACE('',(#442),#104,.F.);

#285=ADVANCED_FACE('',(#443),#105,.F.);

#286=ADVANCED_FACE('',(#444),#106,.F.);

#287=ADVANCED_FACE('',(#445),#107,.F.);

#288=ADVANCED_FACE('',(#446),#108,.T.);

#289=ADVANCED_FACE('',(#447),#109,.T.);

#290=ADVANCED_FACE('',(#448),#110,.F.);

#291=ADVANCED_FACE('',(#59,#60),#355,.F.);

#292=ADVANCED_FACE('',(#449),#111,.T.);

#293=ADVANCED_FACE('',(#450),#112,.T.);

#294=ADVANCED_FACE('',(#451),#113,.F.);

#295=ADVANCED_FACE('',(#61,#62),#356,.T.);

#296=ADVANCED_FACE('',(#63,#64),#114,.F.);

#297=ADVANCED_FACE('',(#65,#66),#45,.F.);

#298=ADVANCED_FACE('',(#67,#68),#115,.F.);

#299=ADVANCED_FACE('',(#69,#70),#46,.F.);

#300=PLANE('',#2023);

#301=PLANE('',#2026);

#302=PLANE('',#2029);

#303=PLANE('',#2031);

#304=PLANE('',#2038);

#305=PLANE('',#2040);

#306=PLANE('',#2042);

#307=PLANE('',#2044);

#308=PLANE('',#2046);

#309=PLANE('',#2048);

#310=PLANE('',#2050);

#311=PLANE('',#2060);

#312=PLANE('',#2063);

#313=PLANE('',#2064);

#314=PLANE('',#2068);

#315=PLANE('',#2069);

#316=PLANE('',#2070);

#317=PLANE('',#2076);

#318=PLANE('',#2078);

#319=PLANE('',#2080);

#320=PLANE('',#2081);

#321=PLANE('',#2082);

#322=PLANE('',#2083);

#323=PLANE('',#2085);

#324=PLANE('',#2086);

#325=PLANE('',#2088);

#326=PLANE('',#2089);

#327=PLANE('',#2090);

#328=PLANE('',#2091);

#329=PLANE('',#2092);

#330=PLANE('',#2093);

#331=PLANE('',#2094);

#332=PLANE('',#2095);

#333=PLANE('',#2096);

#334=PLANE('',#2099);

#335=PLANE('',#2100);

#336=PLANE('',#2102);

#337=PLANE('',#2104);

#338=PLANE('',#2105);

#339=PLANE('',#2107);

#340=PLANE('',#2109);

#341=PLANE('',#2110);

#342=PLANE('',#2111);

#343=PLANE('',#2112);

#344=PLANE('',#2113);

#345=PLANE('',#2114);

#346=PLANE('',#2116);

#347=PLANE('',#2122);

#348=PLANE('',#2154);

#349=PLANE('',#2157);

#350=PLANE('',#2158);

#351=PLANE('',#2161);

#352=PLANE('',#2163);

#353=PLANE('',#2166);

#354=PLANE('',#2170);

#355=PLANE('',#2187);

#356=PLANE('',#2195);

#357=FACE_OUTER_BOUND('',#452,.T.);

#358=FACE_OUTER_BOUND('',#453,.T.);

#359=FACE_OUTER_BOUND('',#454,.T.);

#360=FACE_OUTER_BOUND('',#455,.T.);

#361=FACE_OUTER_BOUND('',#456,.T.);

#362=FACE_OUTER_BOUND('',#457,.T.);

#363=FACE_OUTER_BOUND('',#458,.T.);

#364=FACE_OUTER_BOUND('',#459,.T.);

#365=FACE_OUTER_BOUND('',#460,.T.);

#366=FACE_OUTER_BOUND('',#461,.T.);

#367=FACE_OUTER_BOUND('',#462,.T.);

#368=FACE_OUTER_BOUND('',#463,.T.);

#369=FACE_OUTER_BOUND('',#464,.T.);

#370=FACE_OUTER_BOUND('',#465,.T.);

#371=FACE_OUTER_BOUND('',#466,.T.);

#372=FACE_OUTER_BOUND('',#467,.T.);

#373=FACE_OUTER_BOUND('',#468,.T.);

#374=FACE_OUTER_BOUND('',#469,.T.);

#375=FACE_OUTER_BOUND('',#470,.T.);

#376=FACE_OUTER_BOUND('',#471,.T.);

#377=FACE_OUTER_BOUND('',#472,.T.);

#378=FACE_OUTER_BOUND('',#473,.T.);

#379=FACE_OUTER_BOUND('',#474,.T.);

#380=FACE_OUTER_BOUND('',#475,.T.);

#381=FACE_OUTER_BOUND('',#476,.T.);

#382=FACE_OUTER_BOUND('',#477,.T.);

#383=FACE_OUTER_BOUND('',#478,.T.);

#384=FACE_OUTER_BOUND('',#479,.T.);

#385=FACE_OUTER_BOUND('',#480,.T.);

#386=FACE_OUTER_BOUND('',#481,.T.);

#387=FACE_OUTER_BOUND('',#482,.T.);

#388=FACE_OUTER_BOUND('',#483,.T.);

#389=FACE_OUTER_BOUND('',#484,.T.);

#390=FACE_OUTER_BOUND('',#485,.T.);

#391=FACE_OUTER_BOUND('',#486,.T.);

#392=FACE_OUTER_BOUND('',#487,.T.);

#393=FACE_OUTER_BOUND('',#488,.T.);

#394=FACE_OUTER_BOUND('',#489,.T.);

#395=FACE_OUTER_BOUND('',#490,.T.);

#396=FACE_OUTER_BOUND('',#491,.T.);

#397=FACE_OUTER_BOUND('',#492,.T.);

#398=FACE_OUTER_BOUND('',#493,.T.);

#399=FACE_OUTER_BOUND('',#494,.T.);

#400=FACE_OUTER_BOUND('',#495,.T.);

#401=FACE_OUTER_BOUND('',#496,.T.);

#402=FACE_OUTER_BOUND('',#497,.T.);

#403=FACE_OUTER_BOUND('',#498,.T.);

#404=FACE_OUTER_BOUND('',#499,.T.);

#405=FACE_OUTER_BOUND('',#500,.T.);

#406=FACE_OUTER_BOUND('',#501,.T.);

#407=FACE_OUTER_BOUND('',#502,.T.);

#408=FACE_OUTER_BOUND('',#503,.T.);

#409=FACE_OUTER_BOUND('',#504,.T.);

#410=FACE_OUTER_BOUND('',#505,.T.);

#411=FACE_OUTER_BOUND('',#506,.T.);

#412=FACE_OUTER_BOUND('',#507,.T.);

#413=FACE_OUTER_BOUND('',#508,.T.);

#414=FACE_OUTER_BOUND('',#511,.T.);

#415=FACE_OUTER_BOUND('',#514,.T.);

#416=FACE_OUTER_BOUND('',#515,.T.);

#417=FACE_OUTER_BOUND('',#516,.T.);

#418=FACE_OUTER_BOUND('',#521,.T.);

#419=FACE_OUTER_BOUND('',#522,.T.);

#420=FACE_OUTER_BOUND('',#523,.T.);

#421=FACE_OUTER_BOUND('',#524,.T.);

#422=FACE_OUTER_BOUND('',#525,.T.);

#423=FACE_OUTER_BOUND('',#526,.T.);

#424=FACE_OUTER_BOUND('',#527,.T.);

#425=FACE_OUTER_BOUND('',#528,.T.);

#426=FACE_OUTER_BOUND('',#529,.T.);

#427=FACE_OUTER_BOUND('',#530,.T.);

#428=FACE_OUTER_BOUND('',#531,.T.);

#429=FACE_OUTER_BOUND('',#532,.T.);

#430=FACE_OUTER_BOUND('',#533,.T.);

#431=FACE_OUTER_BOUND('',#534,.T.);

#432=FACE_OUTER_BOUND('',#535,.T.);

#433=FACE_OUTER_BOUND('',#536,.T.);

#434=FACE_OUTER_BOUND('',#539,.T.);

#435=FACE_OUTER_BOUND('',#540,.T.);

#436=FACE_OUTER_BOUND('',#541,.T.);

#437=FACE_OUTER_BOUND('',#542,.T.);

#438=FACE_OUTER_BOUND('',#545,.T.);

#439=FACE_OUTER_BOUND('',#546,.T.);

#440=FACE_OUTER_BOUND('',#547,.T.);

#441=FACE_OUTER_BOUND('',#548,.T.);

#442=FACE_OUTER_BOUND('',#549,.T.);

#443=FACE_OUTER_BOUND('',#550,.T.);

#444=FACE_OUTER_BOUND('',#551,.T.);

#445=FACE_OUTER_BOUND('',#552,.T.);

#446=FACE_OUTER_BOUND('',#553,.T.);

#447=FACE_OUTER_BOUND('',#554,.T.);

#448=FACE_OUTER_BOUND('',#555,.T.);

#449=FACE_OUTER_BOUND('',#558,.T.);

#450=FACE_OUTER_BOUND('',#559,.T.);

#451=FACE_OUTER_BOUND('',#560,.T.);

#452=EDGE_LOOP('',(#585,#586,#587,#588,#589,#590,#591,#592,#593));

#453=EDGE_LOOP('',(#594,#595,#596,#597));

#454=EDGE_LOOP('',(#598,#599,#600,#601));

#455=EDGE_LOOP('',(#602,#603,#604,#605,#606,#607,#608));

#456=EDGE_LOOP('',(#609,#610,#611,#612,#613,#614,#615,#616));

#457=EDGE_LOOP('',(#617,#618,#619,#620));

#458=EDGE_LOOP('',(#621,#622,#623,#624));

#459=EDGE_LOOP('',(#625,#626,#627,#628,#629,#630,#631,#632));

#460=EDGE_LOOP('',(#633,#634,#635,#636,#637,#638,#639,#640));

#461=EDGE_LOOP('',(#641,#642,#643,#644,#645,#646,#647,#648,#649));

#462=EDGE_LOOP('',(#650,#651,#652,#653,#654,#655,#656,#657,#658,#659,#660));

#463=EDGE_LOOP('',(#661,#662,#663,#664,#665,#666,#667,#668,#669));

#464=EDGE_LOOP('',(#670,#671,#672,#673,#674,#675,#676,#677,#678,#679,#680));

#465=EDGE_LOOP('',(#681,#682,#683,#684));

#466=EDGE_LOOP('',(#685,#686,#687,#688));

#467=EDGE_LOOP('',(#689,#690,#691,#692));

#468=EDGE_LOOP('',(#693,#694,#695,#696,#697,#698,#699,#700));

#469=EDGE_LOOP('',(#701,#702,#703,#704,#705,#706,#707,#708,#709,#710,#711,

#712));

#470=EDGE_LOOP('',(#713,#714,#715,#716));

#471=EDGE_LOOP('',(#717,#718,#719,#720));

#472=EDGE_LOOP('',(#721,#722,#723,#724));

#473=EDGE_LOOP('',(#725,#726,#727,#728));

#474=EDGE_LOOP('',(#729,#730,#731,#732));

#475=EDGE_LOOP('',(#733,#734,#735,#736));

#476=EDGE_LOOP('',(#737,#738,#739,#740,#741,#742,#743,#744,#745,#746,#747,

#748,#749,#750));

#477=EDGE_LOOP('',(#751,#752,#753,#754,#755,#756,#757,#758,#759));

#478=EDGE_LOOP('',(#760,#761,#762,#763,#764,#765,#766,#767,#768));

#479=EDGE_LOOP('',(#769,#770,#771,#772,#773,#774,#775,#776));

#480=EDGE_LOOP('',(#777,#778,#779,#780,#781,#782,#783,#784,#785,#786,#787,

#788,#789,#790,#791,#792));

#481=EDGE_LOOP('',(#793,#794,#795,#796,#797,#798,#799,#800,#801,#802));

#482=EDGE_LOOP('',(#803,#804,#805,#806,#807));

#483=EDGE_LOOP('',(#808,#809,#810,#811));

#484=EDGE_LOOP('',(#812,#813,#814,#815,#816));

#485=EDGE_LOOP('',(#817,#818,#819,#820));

#486=EDGE_LOOP('',(#821,#822,#823,#824));

#487=EDGE_LOOP('',(#825,#826,#827,#828));

#488=EDGE_LOOP('',(#829,#830,#831,#832));

#489=EDGE_LOOP('',(#833,#834,#835,#836,#837,#838,#839,#840));

#490=EDGE_LOOP('',(#841,#842,#843,#844));

#491=EDGE_LOOP('',(#845,#846,#847,#848));

#492=EDGE_LOOP('',(#849,#850,#851,#852));

#493=EDGE_LOOP('',(#853,#854,#855,#856,#857));

#494=EDGE_LOOP('',(#858,#859,#860,#861,#862));

#495=EDGE_LOOP('',(#863,#864,#865,#866,#867));

#496=EDGE_LOOP('',(#868,#869,#870,#871,#872));

#497=EDGE_LOOP('',(#873,#874,#875,#876,#877,#878,#879,#880));

#498=EDGE_LOOP('',(#881,#882,#883,#884));

#499=EDGE_LOOP('',(#885,#886,#887,#888,#889));

#500=EDGE_LOOP('',(#890,#891,#892,#893,#894));

#501=EDGE_LOOP('',(#895,#896,#897,#898,#899,#900,#901,#902));

#502=EDGE_LOOP('',(#903,#904,#905,#906));

#503=EDGE_LOOP('',(#907,#908,#909,#910));

#504=EDGE_LOOP('',(#911,#912,#913,#914));

#505=EDGE_LOOP('',(#915,#916,#917,#918));

#506=EDGE_LOOP('',(#919,#920,#921,#922));

#507=EDGE_LOOP('',(#923,#924,#925,#926));

#508=EDGE_LOOP('',(#927,#928,#929,#930));

#509=EDGE_LOOP('',(#931,#932,#933,#934));

#510=EDGE_LOOP('',(#935));

#511=EDGE_LOOP('',(#936,#937,#938,#939,#940,#941,#942,#943));

#512=EDGE_LOOP('',(#944));

#513=EDGE_LOOP('',(#945,#946,#947,#948,#949,#950));

#514=EDGE_LOOP('',(#951,#952,#953,#954));

#515=EDGE_LOOP('',(#955,#956,#957,#958));

#516=EDGE_LOOP('',(#959,#960,#961,#962));

#517=EDGE_LOOP('',(#963));

#518=EDGE_LOOP('',(#964));

#519=EDGE_LOOP('',(#965));

#520=EDGE_LOOP('',(#966));

#521=EDGE_LOOP('',(#967,#968,#969,#970));

#522=EDGE_LOOP('',(#971,#972,#973,#974));

#523=EDGE_LOOP('',(#975,#976,#977,#978));

#524=EDGE_LOOP('',(#979,#980,#981,#982));

#525=EDGE_LOOP('',(#983,#984,#985,#986));

#526=EDGE_LOOP('',(#987,#988,#989,#990));

#527=EDGE_LOOP('',(#991,#992,#993,#994));

#528=EDGE_LOOP('',(#995,#996,#997,#998));

#529=EDGE_LOOP('',(#999,#1000,#1001,#1002));

#530=EDGE_LOOP('',(#1003,#1004,#1005,#1006));

#531=EDGE_LOOP('',(#1007,#1008,#1009));

#532=EDGE_LOOP('',(#1010,#1011,#1012,#1013));

#533=EDGE_LOOP('',(#1014,#1015,#1016,#1017));

#534=EDGE_LOOP('',(#1018,#1019,#1020));

#535=EDGE_LOOP('',(#1021,#1022,#1023,#1024));

#536=EDGE_LOOP('',(#1025,#1026,#1027,#1028));

#537=EDGE_LOOP('',(#1029));

#538=EDGE_LOOP('',(#1030,#1031,#1032,#1033,#1034));

#539=EDGE_LOOP('',(#1035,#1036,#1037,#1038));

#540=EDGE_LOOP('',(#1039,#1040,#1041,#1042,#1043,#1044,#1045,#1046,#1047));

#541=EDGE_LOOP('',(#1048,#1049,#1050,#1051,#1052,#1053,#1054));

#542=EDGE_LOOP('',(#1055,#1056,#1057,#1058));

#543=EDGE_LOOP('',(#1059));

#544=EDGE_LOOP('',(#1060,#1061,#1062,#1063,#1064));

#545=EDGE_LOOP('',(#1065,#1066,#1067,#1068,#1069,#1070,#1071,#1072));

#546=EDGE_LOOP('',(#1073,#1074,#1075,#1076));

#547=EDGE_LOOP('',(#1077,#1078,#1079,#1080,#1081));

#548=EDGE_LOOP('',(#1082,#1083,#1084,#1085,#1086));

#549=EDGE_LOOP('',(#1087,#1088,#1089,#1090,#1091,#1092));

#550=EDGE_LOOP('',(#1093,#1094,#1095,#1096));

#551=EDGE_LOOP('',(#1097,#1098,#1099,#1100));

#552=EDGE_LOOP('',(#1101,#1102,#1103,#1104,#1105,#1106));

#553=EDGE_LOOP('',(#1107,#1108,#1109,#1110));

#554=EDGE_LOOP('',(#1111,#1112,#1113,#1114));

#555=EDGE_LOOP('',(#1115,#1116,#1117,#1118,#1119,#1120));

#556=EDGE_LOOP('',(#1121));

#557=EDGE_LOOP('',(#1122,#1123,#1124,#1125,#1126,#1127));

#558=EDGE_LOOP('',(#1128,#1129,#1130,#1131));

#559=EDGE_LOOP('',(#1132,#1133,#1134,#1135));

#560=EDGE_LOOP('',(#1136,#1137,#1138,#1139,#1140,#1141));

#561=EDGE_LOOP('',(#1142));

#562=EDGE_LOOP('',(#1143,#1144,#1145,#1146,#1147,#1148));

#563=EDGE_LOOP('',(#1149));

#564=EDGE_LOOP('',(#1150));

#565=EDGE_LOOP('',(#1151));

#566=EDGE_LOOP('',(#1152));

#567=EDGE_LOOP('',(#1153));

#568=EDGE_LOOP('',(#1154));

#569=EDGE_LOOP('',(#1155));

#570=EDGE_LOOP('',(#1156));

#571=ELLIPSE('',#2021,0.250139759851571,0.25);

#572=ELLIPSE('',#2022,1.50085358318349,1.5);

#573=ELLIPSE('',#2030,1.50085358318349,1.5);

#574=ELLIPSE('',#2052,0.353553390593275,0.25);

#575=ELLIPSE('',#2055,0.353553390593275,0.25);

#576=ELLIPSE('',#2131,0.353553390593274,0.25);

#577=ELLIPSE('',#2133,0.353553390593274,0.25);

#578=ELLIPSE('',#2136,0.353553390593274,0.25);

#579=ELLIPSE('',#2138,0.353553390593274,0.25);

#580=ELLIPSE('',#2156,0.252975690062489,0.25);

#581=ELLIPSE('',#2159,1.50085358318349,1.5);

#582=ELLIPSE('',#2160,0.250139759851571,0.25);

#583=ELLIPSE('',#2162,1.50085358318349,1.5);

#584=ELLIPSE('',#2169,0.252975690062489,0.25);

#585=ORIENTED_EDGE('',*,*,#1344,.F.);

#586=ORIENTED_EDGE('',*,*,#1345,.F.);

#587=ORIENTED_EDGE('',*,*,#1346,.T.);

#588=ORIENTED_EDGE('',*,*,#1347,.T.);

#589=ORIENTED_EDGE('',*,*,#1348,.T.);

#590=ORIENTED_EDGE('',*,*,#1349,.T.);

#591=ORIENTED_EDGE('',*,*,#1350,.T.);

#592=ORIENTED_EDGE('',*,*,#1351,.T.);

#593=ORIENTED_EDGE('',*,*,#1352,.F.);

#594=ORIENTED_EDGE('',*,*,#1353,.F.);

#595=ORIENTED_EDGE('',*,*,#1354,.F.);

#596=ORIENTED_EDGE('',*,*,#1355,.T.);

#597=ORIENTED_EDGE('',*,*,#1356,.F.);

#598=ORIENTED_EDGE('',*,*,#1357,.F.);

#599=ORIENTED_EDGE('',*,*,#1358,.F.);

#600=ORIENTED_EDGE('',*,*,#1352,.T.);

#601=ORIENTED_EDGE('',*,*,#1359,.T.);

#602=ORIENTED_EDGE('',*,*,#1360,.T.);

#603=ORIENTED_EDGE('',*,*,#1356,.T.);

#604=ORIENTED_EDGE('',*,*,#1361,.T.);

#605=ORIENTED_EDGE('',*,*,#1362,.T.);

#606=ORIENTED_EDGE('',*,*,#1363,.F.);

#607=ORIENTED_EDGE('',*,*,#1364,.T.);

#608=ORIENTED_EDGE('',*,*,#1365,.F.);

#609=ORIENTED_EDGE('',*,*,#1366,.F.);

#610=ORIENTED_EDGE('',*,*,#1359,.F.);

#611=ORIENTED_EDGE('',*,*,#1351,.F.);

#612=ORIENTED_EDGE('',*,*,#1367,.T.);

#613=ORIENTED_EDGE('',*,*,#1368,.F.);

#614=ORIENTED_EDGE('',*,*,#1369,.T.);

#615=ORIENTED_EDGE('',*,*,#1361,.F.);

#616=ORIENTED_EDGE('',*,*,#1355,.F.);

#617=ORIENTED_EDGE('',*,*,#1346,.F.);

#618=ORIENTED_EDGE('',*,*,#1370,.T.);

#619=ORIENTED_EDGE('',*,*,#1364,.F.);

#620=ORIENTED_EDGE('',*,*,#1371,.F.);

#621=ORIENTED_EDGE('',*,*,#1372,.T.);

#622=ORIENTED_EDGE('',*,*,#1373,.T.);

#623=ORIENTED_EDGE('',*,*,#1374,.F.);

#624=ORIENTED_EDGE('',*,*,#1375,.T.);

#625=ORIENTED_EDGE('',*,*,#1376,.T.);

#626=ORIENTED_EDGE('',*,*,#1377,.T.);

#627=ORIENTED_EDGE('',*,*,#1378,.T.);

#628=ORIENTED_EDGE('',*,*,#1379,.T.);

#629=ORIENTED_EDGE('',*,*,#1380,.T.);

#630=ORIENTED_EDGE('',*,*,#1381,.F.);

#631=ORIENTED_EDGE('',*,*,#1382,.T.);

#632=ORIENTED_EDGE('',*,*,#1383,.T.);

#633=ORIENTED_EDGE('',*,*,#1384,.T.);

#634=ORIENTED_EDGE('',*,*,#1385,.F.);

#635=ORIENTED_EDGE('',*,*,#1386,.T.);

#636=ORIENTED_EDGE('',*,*,#1387,.F.);

#637=ORIENTED_EDGE('',*,*,#1388,.F.);

#638=ORIENTED_EDGE('',*,*,#1389,.F.);

#639=ORIENTED_EDGE('',*,*,#1390,.T.);

#640=ORIENTED_EDGE('',*,*,#1391,.T.);

#641=ORIENTED_EDGE('',*,*,#1392,.F.);

#642=ORIENTED_EDGE('',*,*,#1393,.T.);

#643=ORIENTED_EDGE('',*,*,#1394,.F.);

#644=ORIENTED_EDGE('',*,*,#1395,.T.);

#645=ORIENTED_EDGE('',*,*,#1396,.T.);

#646=ORIENTED_EDGE('',*,*,#1397,.T.);

#647=ORIENTED_EDGE('',*,*,#1398,.T.);

#648=ORIENTED_EDGE('',*,*,#1399,.T.);

#649=ORIENTED_EDGE('',*,*,#1400,.F.);

#650=ORIENTED_EDGE('',*,*,#1401,.T.);

#651=ORIENTED_EDGE('',*,*,#1402,.T.);

#652=ORIENTED_EDGE('',*,*,#1392,.T.);

#653=ORIENTED_EDGE('',*,*,#1403,.T.);

#654=ORIENTED_EDGE('',*,*,#1404,.T.);

#655=ORIENTED_EDGE('',*,*,#1405,.T.);

#656=ORIENTED_EDGE('',*,*,#1406,.T.);

#657=ORIENTED_EDGE('',*,*,#1407,.T.);

#658=ORIENTED_EDGE('',*,*,#1408,.T.);

#659=ORIENTED_EDGE('',*,*,#1394,.T.);

#660=ORIENTED_EDGE('',*,*,#1409,.T.);

#661=ORIENTED_EDGE('',*,*,#1410,.T.);

#662=ORIENTED_EDGE('',*,*,#1411,.T.);

#663=ORIENTED_EDGE('',*,*,#1412,.T.);

#664=ORIENTED_EDGE('',*,*,#1413,.F.);

#665=ORIENTED_EDGE('',*,*,#1414,.T.);

#666=ORIENTED_EDGE('',*,*,#1415,.T.);

#667=ORIENTED_EDGE('',*,*,#1416,.T.);

#668=ORIENTED_EDGE('',*,*,#1417,.T.);

#669=ORIENTED_EDGE('',*,*,#1418,.F.);

#670=ORIENTED_EDGE('',*,*,#1368,.T.);

#671=ORIENTED_EDGE('',*,*,#1419,.T.);

#672=ORIENTED_EDGE('',*,*,#1410,.F.);

#673=ORIENTED_EDGE('',*,*,#1420,.F.);

#674=ORIENTED_EDGE('',*,*,#1421,.T.);

#675=ORIENTED_EDGE('',*,*,#1422,.F.);

#676=ORIENTED_EDGE('',*,*,#1423,.F.);

#677=ORIENTED_EDGE('',*,*,#1424,.T.);

#678=ORIENTED_EDGE('',*,*,#1425,.F.);

#679=ORIENTED_EDGE('',*,*,#1412,.F.);

#680=ORIENTED_EDGE('',*,*,#1426,.T.);

#681=ORIENTED_EDGE('',*,*,#1399,.F.);

#682=ORIENTED_EDGE('',*,*,#1427,.F.);

#683=ORIENTED_EDGE('',*,*,#1384,.F.);

#684=ORIENTED_EDGE('',*,*,#1428,.F.);

#685=ORIENTED_EDGE('',*,*,#1377,.F.);

#686=ORIENTED_EDGE('',*,*,#1429,.F.);

#687=ORIENTED_EDGE('',*,*,#1414,.F.);

#688=ORIENTED_EDGE('',*,*,#1430,.F.);

#689=ORIENTED_EDGE('',*,*,#1431,.F.);

#690=ORIENTED_EDGE('',*,*,#1387,.T.);

#691=ORIENTED_EDGE('',*,*,#1432,.T.);

#692=ORIENTED_EDGE('',*,*,#1382,.F.);

#693=ORIENTED_EDGE('',*,*,#1400,.T.);

#694=ORIENTED_EDGE('',*,*,#1433,.T.);

#695=ORIENTED_EDGE('',*,*,#1434,.T.);

#696=ORIENTED_EDGE('',*,*,#1435,.T.);

#697=ORIENTED_EDGE('',*,*,#1413,.T.);

#698=ORIENTED_EDGE('',*,*,#1425,.T.);

#699=ORIENTED_EDGE('',*,*,#1436,.T.);

#700=ORIENTED_EDGE('',*,*,#1403,.F.);

#701=ORIENTED_EDGE('',*,*,#1437,.F.);

#702=ORIENTED_EDGE('',*,*,#1438,.T.);

#703=ORIENTED_EDGE('',*,*,#1439,.T.);

#704=ORIENTED_EDGE('',*,*,#1440,.T.);

#705=ORIENTED_EDGE('',*,*,#1441,.T.);

#706=ORIENTED_EDGE('',*,*,#1442,.T.);

#707=ORIENTED_EDGE('',*,*,#1443,.T.);

#708=ORIENTED_EDGE('',*,*,#1444,.T.);

#709=ORIENTED_EDGE('',*,*,#1445,.T.);

#710=ORIENTED_EDGE('',*,*,#1446,.T.);

#711=ORIENTED_EDGE('',*,*,#1447,.F.);

#712=ORIENTED_EDGE('',*,*,#1448,.F.);

#713=ORIENTED_EDGE('',*,*,#1449,.F.);

#714=ORIENTED_EDGE('',*,*,#1450,.F.);

#715=ORIENTED_EDGE('',*,*,#1451,.T.);

#716=ORIENTED_EDGE('',*,*,#1452,.T.);

#717=ORIENTED_EDGE('',*,*,#1453,.F.);

#718=ORIENTED_EDGE('',*,*,#1454,.T.);

#719=ORIENTED_EDGE('',*,*,#1449,.T.);

#720=ORIENTED_EDGE('',*,*,#1455,.F.);

#721=ORIENTED_EDGE('',*,*,#1456,.T.);

#722=ORIENTED_EDGE('',*,*,#1457,.F.);

#723=ORIENTED_EDGE('',*,*,#1453,.T.);

#724=ORIENTED_EDGE('',*,*,#1458,.T.);

#725=ORIENTED_EDGE('',*,*,#1459,.F.);

#726=ORIENTED_EDGE('',*,*,#1460,.F.);

#727=ORIENTED_EDGE('',*,*,#1461,.F.);

#728=ORIENTED_EDGE('',*,*,#1462,.F.);

#729=ORIENTED_EDGE('',*,*,#1463,.F.);

#730=ORIENTED_EDGE('',*,*,#1464,.T.);

#731=ORIENTED_EDGE('',*,*,#1465,.F.);

#732=ORIENTED_EDGE('',*,*,#1466,.F.);

#733=ORIENTED_EDGE('',*,*,#1467,.F.);

#734=ORIENTED_EDGE('',*,*,#1462,.T.);

#735=ORIENTED_EDGE('',*,*,#1468,.F.);

#736=ORIENTED_EDGE('',*,*,#1464,.F.);

#737=ORIENTED_EDGE('',*,*,#1469,.F.);

#738=ORIENTED_EDGE('',*,*,#1470,.T.);

#739=ORIENTED_EDGE('',*,*,#1471,.T.);

#740=ORIENTED_EDGE('',*,*,#1472,.F.);

#741=ORIENTED_EDGE('',*,*,#1466,.T.);

#742=ORIENTED_EDGE('',*,*,#1473,.F.);

#743=ORIENTED_EDGE('',*,*,#1474,.T.);

#744=ORIENTED_EDGE('',*,*,#1475,.T.);

#745=ORIENTED_EDGE('',*,*,#1476,.F.);

#746=ORIENTED_EDGE('',*,*,#1477,.T.);

#747=ORIENTED_EDGE('',*,*,#1478,.F.);

#748=ORIENTED_EDGE('',*,*,#1479,.T.);

#749=ORIENTED_EDGE('',*,*,#1451,.F.);

#750=ORIENTED_EDGE('',*,*,#1480,.T.);

#751=ORIENTED_EDGE('',*,*,#1405,.F.);

#752=ORIENTED_EDGE('',*,*,#1481,.T.);

#753=ORIENTED_EDGE('',*,*,#1482,.F.);

#754=ORIENTED_EDGE('',*,*,#1483,.T.);

#755=ORIENTED_EDGE('',*,*,#1456,.F.);

#756=ORIENTED_EDGE('',*,*,#1484,.T.);

#757=ORIENTED_EDGE('',*,*,#1485,.T.);

#758=ORIENTED_EDGE('',*,*,#1486,.T.);

#759=ORIENTED_EDGE('',*,*,#1487,.F.);

#760=ORIENTED_EDGE('',*,*,#1488,.T.);

#761=ORIENTED_EDGE('',*,*,#1489,.T.);

#762=ORIENTED_EDGE('',*,*,#1423,.T.);

#763=ORIENTED_EDGE('',*,*,#1490,.F.);

#764=ORIENTED_EDGE('',*,*,#1491,.T.);

#765=ORIENTED_EDGE('',*,*,#1492,.F.);

#766=ORIENTED_EDGE('',*,*,#1493,.F.);

#767=ORIENTED_EDGE('',*,*,#1460,.T.);

#768=ORIENTED_EDGE('',*,*,#1494,.F.);

#769=ORIENTED_EDGE('',*,*,#1452,.F.);

#770=ORIENTED_EDGE('',*,*,#1479,.F.);

#771=ORIENTED_EDGE('',*,*,#1495,.F.);

#772=ORIENTED_EDGE('',*,*,#1496,.T.);

#773=ORIENTED_EDGE('',*,*,#1497,.T.);

#774=ORIENTED_EDGE('',*,*,#1484,.F.);

#775=ORIENTED_EDGE('',*,*,#1458,.F.);

#776=ORIENTED_EDGE('',*,*,#1455,.T.);

#777=ORIENTED_EDGE('',*,*,#1498,.T.);

#778=ORIENTED_EDGE('',*,*,#1499,.T.);

#779=ORIENTED_EDGE('',*,*,#1490,.T.);

#780=ORIENTED_EDGE('',*,*,#1422,.T.);

#781=ORIENTED_EDGE('',*,*,#1500,.T.);

#782=ORIENTED_EDGE('',*,*,#1501,.T.);

#783=ORIENTED_EDGE('',*,*,#1502,.T.);

#784=ORIENTED_EDGE('',*,*,#1503,.T.);

#785=ORIENTED_EDGE('',*,*,#1504,.T.);

#786=ORIENTED_EDGE('',*,*,#1406,.F.);

#787=ORIENTED_EDGE('',*,*,#1487,.T.);

#788=ORIENTED_EDGE('',*,*,#1505,.T.);

#789=ORIENTED_EDGE('',*,*,#1506,.T.);

#790=ORIENTED_EDGE('',*,*,#1507,.T.);

#791=ORIENTED_EDGE('',*,*,#1476,.T.);

#792=ORIENTED_EDGE('',*,*,#1508,.T.);

#793=ORIENTED_EDGE('',*,*,#1415,.F.);

#794=ORIENTED_EDGE('',*,*,#1429,.T.);

#795=ORIENTED_EDGE('',*,*,#1376,.F.);

#796=ORIENTED_EDGE('',*,*,#1509,.T.);

#797=ORIENTED_EDGE('',*,*,#1385,.T.);

#798=ORIENTED_EDGE('',*,*,#1427,.T.);

#799=ORIENTED_EDGE('',*,*,#1398,.F.);

#800=ORIENTED_EDGE('',*,*,#1510,.T.);

#801=ORIENTED_EDGE('',*,*,#1511,.T.);

#802=ORIENTED_EDGE('',*,*,#1512,.T.);

#803=ORIENTED_EDGE('',*,*,#1513,.T.);

#804=ORIENTED_EDGE('',*,*,#1514,.T.);

#805=ORIENTED_EDGE('',*,*,#1396,.F.);

#806=ORIENTED_EDGE('',*,*,#1515,.F.);

#807=ORIENTED_EDGE('',*,*,#1516,.T.);

#808=ORIENTED_EDGE('',*,*,#1408,.F.);

#809=ORIENTED_EDGE('',*,*,#1517,.T.);

#810=ORIENTED_EDGE('',*,*,#1515,.T.);

#811=ORIENTED_EDGE('',*,*,#1395,.F.);

#812=ORIENTED_EDGE('',*,*,#1417,.F.);

#813=ORIENTED_EDGE('',*,*,#1518,.T.);

#814=ORIENTED_EDGE('',*,*,#1519,.T.);

#815=ORIENTED_EDGE('',*,*,#1520,.T.);

#816=ORIENTED_EDGE('',*,*,#1521,.T.);

#817=ORIENTED_EDGE('',*,*,#1521,.F.);

#818=ORIENTED_EDGE('',*,*,#1522,.T.);

#819=ORIENTED_EDGE('',*,*,#1420,.T.);

#820=ORIENTED_EDGE('',*,*,#1418,.T.);

#821=ORIENTED_EDGE('',*,*,#1523,.F.);

#822=ORIENTED_EDGE('',*,*,#1524,.T.);

#823=ORIENTED_EDGE('',*,*,#1474,.F.);

#824=ORIENTED_EDGE('',*,*,#1525,.F.);

#825=ORIENTED_EDGE('',*,*,#1492,.T.);

#826=ORIENTED_EDGE('',*,*,#1526,.T.);

#827=ORIENTED_EDGE('',*,*,#1527,.T.);

#828=ORIENTED_EDGE('',*,*,#1528,.T.);

#829=ORIENTED_EDGE('',*,*,#1527,.F.);

#830=ORIENTED_EDGE('',*,*,#1529,.T.);

#831=ORIENTED_EDGE('',*,*,#1523,.T.);

#832=ORIENTED_EDGE('',*,*,#1530,.T.);

#833=ORIENTED_EDGE('',*,*,#1461,.T.);

#834=ORIENTED_EDGE('',*,*,#1493,.T.);

#835=ORIENTED_EDGE('',*,*,#1528,.F.);

#836=ORIENTED_EDGE('',*,*,#1530,.F.);

#837=ORIENTED_EDGE('',*,*,#1525,.T.);

#838=ORIENTED_EDGE('',*,*,#1473,.T.);

#839=ORIENTED_EDGE('',*,*,#1465,.T.);

#840=ORIENTED_EDGE('',*,*,#1468,.T.);

#841=ORIENTED_EDGE('',*,*,#1531,.F.);

#842=ORIENTED_EDGE('',*,*,#1532,.T.);

#843=ORIENTED_EDGE('',*,*,#1533,.T.);

#844=ORIENTED_EDGE('',*,*,#1496,.F.);

#845=ORIENTED_EDGE('',*,*,#1478,.T.);

#846=ORIENTED_EDGE('',*,*,#1534,.T.);

#847=ORIENTED_EDGE('',*,*,#1531,.T.);

#848=ORIENTED_EDGE('',*,*,#1495,.T.);

#849=ORIENTED_EDGE('',*,*,#1533,.F.);

#850=ORIENTED_EDGE('',*,*,#1535,.T.);

#851=ORIENTED_EDGE('',*,*,#1485,.F.);

#852=ORIENTED_EDGE('',*,*,#1497,.F.);

#853=ORIENTED_EDGE('',*,*,#1407,.F.);

#854=ORIENTED_EDGE('',*,*,#1504,.F.);

#855=ORIENTED_EDGE('',*,*,#1536,.T.);

#856=ORIENTED_EDGE('',*,*,#1516,.F.);

#857=ORIENTED_EDGE('',*,*,#1517,.F.);

#858=ORIENTED_EDGE('',*,*,#1421,.F.);

#859=ORIENTED_EDGE('',*,*,#1522,.F.);

#860=ORIENTED_EDGE('',*,*,#1520,.F.);

#861=ORIENTED_EDGE('',*,*,#1537,.T.);

#862=ORIENTED_EDGE('',*,*,#1500,.F.);

#863=ORIENTED_EDGE('',*,*,#1471,.F.);

#864=ORIENTED_EDGE('',*,*,#1538,.T.);

#865=ORIENTED_EDGE('',*,*,#1437,.T.);

#866=ORIENTED_EDGE('',*,*,#1539,.T.);

#867=ORIENTED_EDGE('',*,*,#1540,.T.);

#868=ORIENTED_EDGE('',*,*,#1447,.T.);

#869=ORIENTED_EDGE('',*,*,#1541,.T.);

#870=ORIENTED_EDGE('',*,*,#1488,.F.);

#871=ORIENTED_EDGE('',*,*,#1542,.T.);

#872=ORIENTED_EDGE('',*,*,#1543,.F.);

#873=ORIENTED_EDGE('',*,*,#1472,.T.);

#874=ORIENTED_EDGE('',*,*,#1540,.F.);

#875=ORIENTED_EDGE('',*,*,#1544,.F.);

#876=ORIENTED_EDGE('',*,*,#1542,.F.);

#877=ORIENTED_EDGE('',*,*,#1494,.T.);

#878=ORIENTED_EDGE('',*,*,#1459,.T.);

#879=ORIENTED_EDGE('',*,*,#1467,.T.);

#880=ORIENTED_EDGE('',*,*,#1463,.T.);

#881=ORIENTED_EDGE('',*,*,#1448,.T.);

#882=ORIENTED_EDGE('',*,*,#1543,.T.);

#883=ORIENTED_EDGE('',*,*,#1544,.T.);

#884=ORIENTED_EDGE('',*,*,#1539,.F.);

#885=ORIENTED_EDGE('',*,*,#1439,.F.);

#886=ORIENTED_EDGE('',*,*,#1545,.T.);

#887=ORIENTED_EDGE('',*,*,#1469,.T.);

#888=ORIENTED_EDGE('',*,*,#1546,.F.);

#889=ORIENTED_EDGE('',*,*,#1547,.T.);

#890=ORIENTED_EDGE('',*,*,#1482,.T.);

#891=ORIENTED_EDGE('',*,*,#1548,.T.);

#892=ORIENTED_EDGE('',*,*,#1441,.F.);

#893=ORIENTED_EDGE('',*,*,#1549,.F.);

#894=ORIENTED_EDGE('',*,*,#1550,.F.);

#895=ORIENTED_EDGE('',*,*,#1480,.F.);

#896=ORIENTED_EDGE('',*,*,#1450,.T.);

#897=ORIENTED_EDGE('',*,*,#1454,.F.);

#898=ORIENTED_EDGE('',*,*,#1457,.T.);

#899=ORIENTED_EDGE('',*,*,#1483,.F.);

#900=ORIENTED_EDGE('',*,*,#1550,.T.);

#901=ORIENTED_EDGE('',*,*,#1551,.T.);

#902=ORIENTED_EDGE('',*,*,#1546,.T.);

#903=ORIENTED_EDGE('',*,*,#1440,.F.);

#904=ORIENTED_EDGE('',*,*,#1547,.F.);

#905=ORIENTED_EDGE('',*,*,#1551,.F.);

#906=ORIENTED_EDGE('',*,*,#1549,.T.);

#907=ORIENTED_EDGE('',*,*,#1541,.F.);

#908=ORIENTED_EDGE('',*,*,#1446,.F.);

#909=ORIENTED_EDGE('',*,*,#1552,.F.);

#910=ORIENTED_EDGE('',*,*,#1489,.F.);

#911=ORIENTED_EDGE('',*,*,#1552,.T.);

#912=ORIENTED_EDGE('',*,*,#1445,.F.);

#913=ORIENTED_EDGE('',*,*,#1553,.F.);

#914=ORIENTED_EDGE('',*,*,#1424,.F.);

#915=ORIENTED_EDGE('',*,*,#1553,.T.);

#916=ORIENTED_EDGE('',*,*,#1444,.F.);

#917=ORIENTED_EDGE('',*,*,#1554,.F.);

#918=ORIENTED_EDGE('',*,*,#1436,.F.);

#919=ORIENTED_EDGE('',*,*,#1554,.T.);

#920=ORIENTED_EDGE('',*,*,#1443,.F.);

#921=ORIENTED_EDGE('',*,*,#1555,.F.);

#922=ORIENTED_EDGE('',*,*,#1404,.F.);

#923=ORIENTED_EDGE('',*,*,#1555,.T.);

#924=ORIENTED_EDGE('',*,*,#1442,.F.);

#925=ORIENTED_EDGE('',*,*,#1548,.F.);

#926=ORIENTED_EDGE('',*,*,#1481,.F.);

#927=ORIENTED_EDGE('',*,*,#1545,.F.);

#928=ORIENTED_EDGE('',*,*,#1438,.F.);

#929=ORIENTED_EDGE('',*,*,#1538,.F.);

#930=ORIENTED_EDGE('',*,*,#1470,.F.);

#931=ORIENTED_EDGE('',*,*,#1386,.F.);

#932=ORIENTED_EDGE('',*,*,#1509,.F.);

#933=ORIENTED_EDGE('',*,*,#1383,.F.);

#934=ORIENTED_EDGE('',*,*,#1432,.F.);

#935=ORIENTED_EDGE('',*,*,#1556,.T.);

#936=ORIENTED_EDGE('',*,*,#1390,.F.);

#937=ORIENTED_EDGE('',*,*,#1557,.T.);

#938=ORIENTED_EDGE('',*,*,#1558,.T.);

#939=ORIENTED_EDGE('',*,*,#1559,.T.);

#940=ORIENTED_EDGE('',*,*,#1379,.F.);

#941=ORIENTED_EDGE('',*,*,#1560,.T.);

#942=ORIENTED_EDGE('',*,*,#1434,.F.);

#943=ORIENTED_EDGE('',*,*,#1561,.T.);

#944=ORIENTED_EDGE('',*,*,#1562,.T.);

#945=ORIENTED_EDGE('',*,*,#1381,.T.);

#946=ORIENTED_EDGE('',*,*,#1563,.T.);

#947=ORIENTED_EDGE('',*,*,#1564,.T.);

#948=ORIENTED_EDGE('',*,*,#1565,.T.);

#949=ORIENTED_EDGE('',*,*,#1388,.T.);

#950=ORIENTED_EDGE('',*,*,#1431,.T.);

#951=ORIENTED_EDGE('',*,*,#1389,.T.);

#952=ORIENTED_EDGE('',*,*,#1565,.F.);

#953=ORIENTED_EDGE('',*,*,#1566,.T.);

#954=ORIENTED_EDGE('',*,*,#1557,.F.);

#955=ORIENTED_EDGE('',*,*,#1566,.F.);

#956=ORIENTED_EDGE('',*,*,#1564,.F.);

#957=ORIENTED_EDGE('',*,*,#1567,.T.);

#958=ORIENTED_EDGE('',*,*,#1558,.F.);

#959=ORIENTED_EDGE('',*,*,#1567,.F.);

#960=ORIENTED_EDGE('',*,*,#1563,.F.);

#961=ORIENTED_EDGE('',*,*,#1380,.F.);

#962=ORIENTED_EDGE('',*,*,#1559,.F.);

#963=ORIENTED_EDGE('',*,*,#1568,.T.);

#964=ORIENTED_EDGE('',*,*,#1556,.F.);

#965=ORIENTED_EDGE('',*,*,#1568,.F.);

#966=ORIENTED_EDGE('',*,*,#1562,.F.);

#967=ORIENTED_EDGE('',*,*,#1433,.F.);

#968=ORIENTED_EDGE('',*,*,#1428,.T.);

#969=ORIENTED_EDGE('',*,*,#1391,.F.);

#970=ORIENTED_EDGE('',*,*,#1561,.F.);

#971=ORIENTED_EDGE('',*,*,#1560,.F.);

#972=ORIENTED_EDGE('',*,*,#1378,.F.);

#973=ORIENTED_EDGE('',*,*,#1430,.T.);

#974=ORIENTED_EDGE('',*,*,#1435,.F.);

#975=ORIENTED_EDGE('',*,*,#1475,.F.);

#976=ORIENTED_EDGE('',*,*,#1524,.F.);

#977=ORIENTED_EDGE('',*,*,#1569,.F.);

#978=ORIENTED_EDGE('',*,*,#1508,.F.);

#979=ORIENTED_EDGE('',*,*,#1569,.T.);

#980=ORIENTED_EDGE('',*,*,#1529,.F.);

#981=ORIENTED_EDGE('',*,*,#1570,.F.);

#982=ORIENTED_EDGE('',*,*,#1498,.F.);

#983=ORIENTED_EDGE('',*,*,#1570,.T.);

#984=ORIENTED_EDGE('',*,*,#1526,.F.);

#985=ORIENTED_EDGE('',*,*,#1491,.F.);

#986=ORIENTED_EDGE('',*,*,#1499,.F.);

#987=ORIENTED_EDGE('',*,*,#1486,.F.);

#988=ORIENTED_EDGE('',*,*,#1535,.F.);

#989=ORIENTED_EDGE('',*,*,#1571,.F.);

#990=ORIENTED_EDGE('',*,*,#1505,.F.);

#991=ORIENTED_EDGE('',*,*,#1571,.T.);

#992=ORIENTED_EDGE('',*,*,#1532,.F.);

#993=ORIENTED_EDGE('',*,*,#1572,.F.);

#994=ORIENTED_EDGE('',*,*,#1506,.F.);

#995=ORIENTED_EDGE('',*,*,#1572,.T.);

#996=ORIENTED_EDGE('',*,*,#1534,.F.);

#997=ORIENTED_EDGE('',*,*,#1477,.F.);

#998=ORIENTED_EDGE('',*,*,#1507,.F.);

#999=ORIENTED_EDGE('',*,*,#1536,.F.);

#1000=ORIENTED_EDGE('',*,*,#1503,.F.);

#1001=ORIENTED_EDGE('',*,*,#1573,.F.);

#1002=ORIENTED_EDGE('',*,*,#1513,.F.);

#1003=ORIENTED_EDGE('',*,*,#1397,.F.);

#1004=ORIENTED_EDGE('',*,*,#1514,.F.);

#1005=ORIENTED_EDGE('',*,*,#1574,.F.);

#1006=ORIENTED_EDGE('',*,*,#1510,.F.);

#1007=ORIENTED_EDGE('',*,*,#1574,.T.);

#1008=ORIENTED_EDGE('',*,*,#1573,.T.);

#1009=ORIENTED_EDGE('',*,*,#1575,.F.);

#1010=ORIENTED_EDGE('',*,*,#1537,.F.);

#1011=ORIENTED_EDGE('',*,*,#1519,.F.);

#1012=ORIENTED_EDGE('',*,*,#1576,.F.);

#1013=ORIENTED_EDGE('',*,*,#1501,.F.);

#1014=ORIENTED_EDGE('',*,*,#1575,.T.);

#1015=ORIENTED_EDGE('',*,*,#1502,.F.);

#1016=ORIENTED_EDGE('',*,*,#1577,.F.);

#1017=ORIENTED_EDGE('',*,*,#1511,.F.);

#1018=ORIENTED_EDGE('',*,*,#1577,.T.);

#1019=ORIENTED_EDGE('',*,*,#1576,.T.);

#1020=ORIENTED_EDGE('',*,*,#1578,.F.);

#1021=ORIENTED_EDGE('',*,*,#1416,.F.);

#1022=ORIENTED_EDGE('',*,*,#1512,.F.);

#1023=ORIENTED_EDGE('',*,*,#1578,.T.);

#1024=ORIENTED_EDGE('',*,*,#1518,.F.);

#1025=ORIENTED_EDGE('',*,*,#1579,.F.);

#1026=ORIENTED_EDGE('',*,*,#1580,.T.);

#1027=ORIENTED_EDGE('',*,*,#1581,.T.);

#1028=ORIENTED_EDGE('',*,*,#1348,.F.);

#1029=ORIENTED_EDGE('',*,*,#1582,.T.);

#1030=ORIENTED_EDGE('',*,*,#1347,.F.);

#1031=ORIENTED_EDGE('',*,*,#1371,.T.);

#1032=ORIENTED_EDGE('',*,*,#1363,.T.);

#1033=ORIENTED_EDGE('',*,*,#1583,.T.);

#1034=ORIENTED_EDGE('',*,*,#1579,.T.);

#1035=ORIENTED_EDGE('',*,*,#1584,.T.);

#1036=ORIENTED_EDGE('',*,*,#1585,.T.);

#1037=ORIENTED_EDGE('',*,*,#1586,.T.);

#1038=ORIENTED_EDGE('',*,*,#1587,.T.);

#1039=ORIENTED_EDGE('',*,*,#1588,.T.);

#1040=ORIENTED_EDGE('',*,*,#1589,.T.);

#1041=ORIENTED_EDGE('',*,*,#1590,.F.);

#1042=ORIENTED_EDGE('',*,*,#1591,.T.);

#1043=ORIENTED_EDGE('',*,*,#1592,.T.);

#1044=ORIENTED_EDGE('',*,*,#1593,.T.);

#1045=ORIENTED_EDGE('',*,*,#1584,.F.);

#1046=ORIENTED_EDGE('',*,*,#1594,.T.);

#1047=ORIENTED_EDGE('',*,*,#1595,.T.);

#1048=ORIENTED_EDGE('',*,*,#1374,.T.);

#1049=ORIENTED_EDGE('',*,*,#1596,.F.);

#1050=ORIENTED_EDGE('',*,*,#1597,.T.);

#1051=ORIENTED_EDGE('',*,*,#1598,.T.);

#1052=ORIENTED_EDGE('',*,*,#1599,.F.);

#1053=ORIENTED_EDGE('',*,*,#1600,.T.);

#1054=ORIENTED_EDGE('',*,*,#1601,.T.);

#1055=ORIENTED_EDGE('',*,*,#1602,.T.);

#1056=ORIENTED_EDGE('',*,*,#1603,.T.);

#1057=ORIENTED_EDGE('',*,*,#1604,.T.);

#1058=ORIENTED_EDGE('',*,*,#1590,.T.);

#1059=ORIENTED_EDGE('',*,*,#1605,.T.);

#1060=ORIENTED_EDGE('',*,*,#1606,.T.);

#1061=ORIENTED_EDGE('',*,*,#1594,.F.);

#1062=ORIENTED_EDGE('',*,*,#1587,.F.);

#1063=ORIENTED_EDGE('',*,*,#1607,.T.);

#1064=ORIENTED_EDGE('',*,*,#1599,.T.);

#1065=ORIENTED_EDGE('',*,*,#1604,.F.);

#1066=ORIENTED_EDGE('',*,*,#1608,.T.);

#1067=ORIENTED_EDGE('',*,*,#1375,.F.);

#1068=ORIENTED_EDGE('',*,*,#1601,.F.);

#1069=ORIENTED_EDGE('',*,*,#1609,.T.);

#1070=ORIENTED_EDGE('',*,*,#1401,.F.);

#1071=ORIENTED_EDGE('',*,*,#1610,.T.);

#1072=ORIENTED_EDGE('',*,*,#1591,.F.);

#1073=ORIENTED_EDGE('',*,*,#1611,.F.);

#1074=ORIENTED_EDGE('',*,*,#1595,.F.);

#1075=ORIENTED_EDGE('',*,*,#1606,.F.);

#1076=ORIENTED_EDGE('',*,*,#1598,.F.);

#1077=ORIENTED_EDGE('',*,*,#1581,.F.);

#1078=ORIENTED_EDGE('',*,*,#1612,.T.);

#1079=ORIENTED_EDGE('',*,*,#1411,.F.);

#1080=ORIENTED_EDGE('',*,*,#1613,.T.);

#1081=ORIENTED_EDGE('',*,*,#1349,.F.);

#1082=ORIENTED_EDGE('',*,*,#1393,.F.);

#1083=ORIENTED_EDGE('',*,*,#1614,.T.);

#1084=ORIENTED_EDGE('',*,*,#1585,.F.);

#1085=ORIENTED_EDGE('',*,*,#1593,.F.);

#1086=ORIENTED_EDGE('',*,*,#1615,.T.);

#1087=ORIENTED_EDGE('',*,*,#1609,.F.);

#1088=ORIENTED_EDGE('',*,*,#1600,.F.);

#1089=ORIENTED_EDGE('',*,*,#1607,.F.);

#1090=ORIENTED_EDGE('',*,*,#1586,.F.);

#1091=ORIENTED_EDGE('',*,*,#16…