Travis Bldg B241 - Bay B Ltd Asbestos and Lead Survey Report.pdf

554 Morning Glory Drive, Benicia, CA 94510· (707) 745-1137· http://www.acs-ltd.us

AMERICAN COMPLIANCE SERVICES, LTD

LIMITED ASBESTOS & LEAD PAINT SURVEY

TRAVIS AIR FORCE BASE

BUILDING 241 Bay B

PREPARED FOR:

Mr. Carl Christian

CA 9453560 CES/CEOES

241 V Street, Bldg. 878 Travis AFB, CA 94535

PREPARED BY:

American Compliance Services, LTD 554 Morning Glory Drive

Benicia, CA 94510

DATE PREPARED:

April 7, 2025

Table of Contents

SECTION I EXECUTIVE SUMMARY

SECTION II SCOPE OF WORK

SECTION III DEFINITIONS

ASBESTOS

LEAD

SECTION IV ASBESTOS INSPECTION RESULTS & FINDINGS

Table 1 - Asbestos Table

SECTION V LEAD INSPECTION RESULTS & FINDINGS

Table 2 Lead Sample Results

Table 3 - Lead TTLC

SECTION VI METHODS

ASBESTOS

SECTION VII NOTICE, PERMITS, AND LICENSES

SECTION VIII LIMITATION AND EXCLUSIONS

SECTION IX TECHNICAL STAFF SIGNATURES - CERTIFICATE OF REPORT

Attachments Sample Location Map(s) Laboratory Results Codes and Regulations Consultants’ Certification(s)

Limited Asbestos and Lead Survey Travis Air Force Base Building 241, Bay B Travis, California Page 1 of 8

SECTION I EXECUTIVE SUMMARY

On March 31, 2025, American Compliance Services, LTD (ACS) conducted a limited asbestos and lead survey in Building 241, in Bay B, at Travis Air Force Base, in Travis, California. Sofia and David Kummer, Certified Site Surveillance Technicians (CSST) and CDPH Lead Sampling Technicians, conducted the survey.

SECTION II SCOPE OF WORK

The purpose of this survey was to test the flooring, wall and ceiling material in Bay B, for lead and asbestos prior to disturbance of the material. Should the final construction plans change and require penetration into materials not included in this report, additional sampling and analysis will be required at this site.

SECTION III DEFINITIONS

ASBESTOS

A material is considered by the EPA and the State of California to be an Asbestos Containing Material (ACM) if at least one sample collected from the homogeneous area shows asbestos present in an amount greater than one percent (>1%) https://www.dir.ca.gov/title8/ch3_2sb2a2_5.html. California Code of Regulations (CCR) 1529 defines Asbestos Containing Construction Material (ACCM) as materials containing greater than one-tenth of one-percent (0.1) asbestos by weight. Under 1529 CCR, materials containing between 0.1 % and 1 % asbestos are still regulated as “other” operations by this standard. The ACCM designation is applicable only to reporting (user registration, temporary worksite notification, and incident reporting). https://www.dir.ca.gov/title8/1529.html

The removal or disturbance of 100 square feet or more of ACM or ACCM must be performed by a contractor certified by the California Contractor's State License Board to conduct asbestos-related work and/or an employer/contractor registered with the California Division of Occupational Safety and Health (DOSH) to perform asbestos-related work.

OSHA CLASSIFICATIONS

"Class I asbestos work" means activities involving the removal of TSI and surfacing ACM and

PACM.

"Class II asbestos work" means activities involving the removal of ACM which is not thermal system insulation or surfacing material. This includes, but is not limited to, the removal of asbestos-containing wallboard, floor tile and sheeting, roofing and siding shingles, and construction mastics.

"Class III asbestos work" means repair and maintenance operations, where "ACM", including TSI and surfacing ACM and PACM, is likely to be disturbed.

“Class IV asbestos work” means maintenance and custodial activities during which employees contact but do not disturb ACM or PACM and activities to clean up dust, waste and debris resulting from Class I, II, and III activities.

“Disturbance” means activities that disrupt the matrix of ACM or PACM, crumble or pulverize ACM or PACM, or generate visible debris from ACM or PACM. Disturbance includes cutting

Travis, California Page 2 of 8 away small amounts of ACM and PACM, no greater than the amount which can be contained in one standard sized glove bag or waste bag in order to access a building component. In no event shall the amount of ACM or PACM so disturbed exceed that which can be contained in one glove bag or waste bag which shall not exceed 60 inches in length and width.

NESHAP CATEGORIES

Friable Materials (RACM) NESHAP defines a friable ACM as any material containing more than one percent asbestos that when dry, can be crumbled, pulverized, or reduced to powder by hand pressure.

Category I Non-friable NESHAP defines a Category I non-friable ACM as packing, gaskets, resilient floor covering (except sheet flooring products which are considered friable), and asphalt roofing products which contain more than one percent asbestos.

Category II Non-friable NESHAP defines a Category II non-friable ACM as any material, except for a Category I non-friable ACM, which contains more than one- percent asbestos and cannot be reduced to a powder by hand pressure when dry.

LEAD

CAL-OSHA Lead Definitions

The Cal/OSHA Lead in Construction Standard 1532.1 regulations takes effect when employees disturb lead coatings or materials that contain any detectable levels of lead. California OSHA regulations assume exposures above the Permissible Exposure Level (PEL) where lead coatings or paint with lead at any level is present when “trigger” tasks are performed until an exposure assessment is conducted. The contractor must comply with this regulation when disturbing lead containing paint or materials.

NESHAP 40 CFR, Part 61 M, and the EPA rule “Lead: Renovation, Repair and Painting Activities that Disturb Lead-Based Paint”, EPA 40 CFR 745.227 Title 40 - Protection of Environment for conducting lead-based paint activities and 40 CFR 745.85 for conducting renovations. https://www.law.cornell.edu/cfr/text/40/745.85

SECTION IV ASBESTOS INSPECTION RESULTS & FINDINGS

ACS collected twenty-two (22) asbestos samples from the building for laboratory analysis. EPA guidelines were used to determine the sampling protocol. Asbestos was detected in the floor tile under the carpet in the Offices. The results are summarized in the table below:

Travis, California Page 3 of 8

Table 1 - Asbestos Table

SAMPLE

NUMBER

MATERIAL

DESCRIPTION

SAMPLE

LOCATION/

HOMOGENEOUS

AREA

NESHAP /

OSHA

CATEGORIES

% ASBESTOS

ESTIMATED

QUANTITY

01-1 01-2 01-3

Smooth Drywall System

Area 1, 2, 3 and 4, Shower 1 and 2, Hall 1, 2, 3 and

Office

NA

Drywall: ND

Compound: ND Tape/Paint: ND

NA

02-4 02-5

1x1 Ceiling/Wall Tile

Area 3, 4, Hall 3 and Office

NA

Ceiling Tile: ND

Mastic: ND

NA

03-6 03-7

Brown Carpet / Mastic

Area 4 and Office NA Carpet: ND Mastic: ND

Leveling Compound: ND

NA

04-8 04-9

4” Brown Base Cove/ Mastic

Area 1, 2, 3 and 4, Shower 1, Hall 1, 2, 3 and Office

NA

Mastic: ND Paint: ND

Base Cove: ND Compound: ND

NA

05-10 05-11

Window Putty Area 4 NA Putty: ND Paint: ND

NA

06-12 9x9 Black Vinyl

Floor Tile/ Mastic Area 3, 4, Hall 3 and Office

CAT I NF

Class II

VFT: 5% CH

Mastic is inseparable from

VFT without cross contamination

2,885 SF

07-13 9x9 Gray Vinyl

Floor Tile/ Mastic Area 3, 4, Hall 3 and Office

CAT I NF

Class II

VFT: 5% CH

Mastic is inseparable from

VFT without cross contamination

08-14 08-15

Blue Carpet Mastic

Hall 1 and 2 NA Carpet: ND Mastic: ND

NA

09-16 09-17

12x12 White / Streak VFT/

Mastic

Shower 1, Area 1 and 2

NA

VFT: ND

Mastic: ND

NA

10-18 10-19

2x2 Ceiling Tile Hall 1 NA Ceiling Tile: ND

Coating White: ND

NA

11-20 Wall Paper/Glue Hall 1 NA Wall Paper: ND

Mastic: ND Drywall: ND

NA

12-21 Green Ceramic

Tile Shower 1 and 2 NA

Ceramic Tile: ND Mastic: ND

NA

13-22 HVAC Vibration

Boot Area 3 NA ND NA

NA: Asbestos classification and estimated quantities are not applicable for non-asbestos containing material; ND: Non-Detect; CH Chrysotile asbestos Type; SF: Square Feet.

The Contractor must obtain all building and special permits required for the asbestos abatement work. When removing 100 square or linear feet or greater of asbestos containing material with an asbestos content of greater than one-tenth of one-percent (0.1) asbestos by weight., the work must be performed by an entity that holds a current, valid asbestos handling license issued by the California State Contractor’s Licensing Board (SCLB) and a current valid Certificate of Registration for Asbestos-Related Work issued by the California Department of Industrial Relations-Division of Occupational Safety and Health (DOSH), unless otherwise specified.

Travis, California Page 4 of 8

SECTION V LEAD INSPECTION RESULTS & FINDINGS

Seven (7) lead samples were collected during the survey. The material sampled is representative of the homogenous areas. The paint on the concrete wall, tan paint on the door trim, tan and brown paint on the windows are determined to be lead-based. The laboratory results are presented in the table below.

Table 2 Lead Sample Results

Sample # Description and Location Results ppm

EPA/CDPH

LBP Limit

P2 Tan Paint on Concrete Wall 19,000 ppm 5,000 ppm

P3 Tan Paint on Ceiling <79 ppm 5,000 ppm

P5 Tan Paint on Door Trim 250 ppm 5,000 ppm

P6 Tan Paint on Door Trim 7,800 ppm 5,000 ppm

P7 Tan Paint on Drywall 260 ppm 5,000 ppm

P8 Tan Paint on Window 6,5000 ppm 5,000 ppm

P9 Brown Paint on Window 91,000 ppm 5,000 ppm ppm: parts per million; EPA: Environmental Protection Agency; CDPH: CA Department of Public Health; LBP: Lead-Based Paint; <: Less than the laboratory’s detection limit, none detected.

One (1) sample of window putty and one of the ceramic tiles were collected for lead analysis. The samples were considered Bulk Material, and cannot be analyzed using the standard Flame Atomic Absorption Spectrophotometer (FLAA) method of paint analysis. The laboratory uses Total Threshold Limit Concentration (TTLC) for bulk material. When results are above 50 milligrams / Liter (mg/L), after the material becomes a waste, it must be retested using the STLC and TCLP to determine if it is a Hazardous Waste prior to disposal. When the TTLC results is at, or above 1,000 mg/L for lead, it is determined to be a Hazardous Waste when disposed in California.

Table 3 - Lead TTLC

SAMPLE

DESCRIPTION AND LOCATION Result (ppm)

EPA / CDPH

Limits

P1 Window Putty 800 >50 mg/L

P2 Green Ceramic Tile 950 >50 mg/L ppm: parts per million; EPA: Environmental Protection Agency; CDPH: CA Department of Public Health/ mg/L: milligrams / Liter.

A lead notification to Cal-OSHA is required 24 hours prior to removing lead-based paint when disturbing 100 square or linear feet or greater.

When the lead-based paint identified in this report will be disturbed through maintenance or demolition activities, the contractor must comply with the EPA and CDPH regulations that require containment of lead hazards so as not to create lead contamination and exposure to bystanders or the environment.

The Cal/OSHA Lead in Construction Standard 1532.1 regulations take effect when employees disturb lead coatings or materials that contain any detectable levels of lead. California OSHA regulations assume exposures above the Permissible Exposure Level (PEL) where lead coatings or paint with lead at any level is present when “trigger” tasks are performed until an exposure

Travis, California Page 5 of 8 assessment is conducted. The contractor must comply with this regulation when disturbing lead containing paint or materials.

The revised Cal-OSHA Lead Standard reduces the lead Action Level (AL) from 30 to 2 micrograms per cubic meter of air and the Permissible Exposure Limit (PEL) from 50 to 10 micrograms per cubic meter of air. This change went into effect January 1, 2025.

SECTION VI METHODS

ASBESTOS

Asbestos Inspection and sampling procedures were performed in general accordance with the guidelines published by the Environmental Protection Agency (EPA) in 40 CFR Part 763 Subpart E, October 30, 1987. https://www.law.cornell.edu/cfr/text/40/part-763/subpart-E The survey consisted of three major activities: visual inspection and physical assessment, sampling, and quantification of building materials.

ASBESTOS BULK SAMPLE ANALYSIS

Micro Analytical Laboratory in Emeryville, California performed the Asbestos analysis. A chain-of-custody form submitted with the bulk samples, documented the possession of the samples from the time they were collected until they were analyzed. The original chain-of-custody accompanied the samples at all times. Custody documentation began at the time the sample was collected and a copy of the chain-of-custody record was retained by each transferor. The laboratory performed the asbestos analysis using the bulk sample for visual observation and slide preparation(s) for microscopic examination and identification. They mounted samples on slides and then analyzed the samples for asbestos (chrysotile, amosite, crocidolite, anthophyllite, and actinolite/tremolite), fibrous non-asbestos constituents (mineral wool, paper, etc.) and non-fibrous constituents. Asbestos was identified by refractive indices, morphology, color, pleochroism, birefringence, extinction characteristics, and signs of elongation. The same characteristics were used to identify the non-asbestos constituents. The microscopist visually estimated relative amounts of each constituent using a stereoscope to determine the volume of each constituent in proportion to the total volume of the sample.

All bulk samples were analyzed by Polarized Light Microscopy (PLM) with dispersion staining as described by the method of the determination of asbestos in bulk insulation, EPA/600/R-93/116, July 1993. This is a standard method of analysis in optical mineralogy and the currently accepted method for the determination of asbestos in bulk samples. A suspect material is immersed in a solution of known refractive index and subjected to illumination by polarized light. The characteristic color displayed enables mineral identification. It should be noted that some ACM might not be accurately identified and/or quantified by PLM. As an example, the original fabrication of vinyl floor tiles routinely involved milling of asbestos fibers to extremely small sizes.

As a result, these fibers may go undetected under the standard polarized light microscopy method. Transmission Electron Microscopy (TEM) is required for a more definitive analysis of these materials.

QUANTIFICATION

Quantities of accessible and/or exposed building materials that were confirmed to contain asbestos were estimated using field measurements and available drawings. Quantities are not applicable for non-asbestos containing material

Travis, California Page 6 of 8

ASBESTOS BULK SAMPLE ANALYSIS

Micro Analytical Laboratory in Emeryville, California performed the Asbestos analysis. A chain-of-custody form submitted with the bulk samples, documented the possession of the samples from the time they were collected until they were analyzed. The original chain-of-custody accompanied the samples at all times. Custody documentation began at the time the sample was collected and a copy of the chain-of-custody record was retained by each transferor. The laboratory performed the asbestos analysis using the bulk sample for visual observation and slide preparation(s) for microscopic examination and identification. They mounted samples on slides and then analyzed the samples for asbestos (chrysotile, amosite, crocidolite, anthophyllite, and actinolite/tremolite), fibrous non-asbestos constituents (mineral wool, paper, etc.) and non-fibrous constituents. Asbestos was identified by refractive indices, morphology, color, pleochroism, birefringence, extinction characteristics, and signs of elongation. The same characteristics were used to identify the non-asbestos constituents. The microscopist visually estimated relative amounts of each constituent using a stereoscope to determine the volume of each constituent in proportion to the total volume of the sample.

All bulk samples were analyzed by Polarized Light Microscopy (PLM) with dispersion staining as described by the method of the determination of asbestos in bulk insulation, EPA/600/R-93/116, July 1993. This is a standard method of analysis in optical mineralogy and the currently accepted method for the determination of asbestos in bulk samples. A suspect material is immersed in a solution of known refractive index and subjected to illumination by polarized light. The characteristic color displayed enables mineral identification. It should be noted that some ACM might not be accurately identified and/or quantified by PLM. As an example, the original fabrication of vinyl floor tiles routinely involved milling of asbestos fibers to extremely small sizes.

As a result, these fibers may go undetected under the standard polarized light microscopy method. Transmission Electron Microscopy (TEM) is required for a more definitive analysis of these materials.

LEAD

The Lead inspection was performed in general accordance with EPA and CDPH guidelines and procedures. The paint chip samples taken were approximately 2” x 2“, representing all potential paint layers. Testing locations were recorded on a diagram, as provided in the appendix.

Sampling locations were chosen to be representative of the homogeneous material.

LEAD ANALYTICAL METHODS

Lead analysis was performed by Micro Analytics Incorporated, a NLLAP-accredited laboratory using a Flame Atomic Absorption Spectrophotometer (FLAA) (Method 7420). The FLAA was calibrated using a known lead standard. After the FLAA calibration procedure was completed, the lead-chip samples were analyzed by the FLAA.

SECTION VII NOTICE, PERMITS, AND LICENSES

Hazardous materials removed during the abatement activities shall be disposed of in an approved manner complying with all applicable federal, state, and local regulations. The following notices, permits, and licenses are necessary for asbestos abatement work as of the date of this report.

The Contractor is cautioned to verify these requirements as applicable to the final project scope and confirm that no new requirements exist.

Travis, California Page 7 of 8

LOCAL AIR QUALITY BOARD NOTIFICATION

Written notification is required to the Local Area Air Quality Management District at least 10 days prior to beginning any work on specified quantities of friable, Regulated Asbestos-Containing Materials (RACM) and / prior to working on ACM using mechanical means or methods that will render the material friable.

CAL-OSHA NOTIFICATION

Written notification to the California Occupational Safety and Health Administration (Cal-OSHA) is required by Cal-OSHA Asbestos Regulations (Title 8, Section 341.9) at least 24 hours prior to beginning any work on asbestos-containing materials.

Prior to the abatement, all employees, contractors, or other parties who may be affected by the abatement must be advised of activities pursuant to Cal-OSHA Asbestos and Lead Regulations (Title 8, Section 1529, Subpart K; Section 1532.1).

SECTION VIII LIMITATION AND EXCLUSIONS

American Compliance Services, LTD (ACS), warrants that the findings contained herein have been prepared with the level of care and skill exercised by experienced and knowledgeable environmental consultants who are appropriately licensed or otherwise trained to perform asbestos / lead assessments pursuant to OSHA, as well as state and local agencies, as applicable. Our responsibility is limited to correcting any error or omission. No other liability is included or implied. We did not inspect or sample inaccessible areas such as behind walls or within ductwork and did not dismantle any part of the structure to survey inaccessible areas.

Inaccessible is defined as areas of the building that could not be tested (sampled) without destruction of the structure or a portion of the structure.

Information and opinions presented herein apply to the existing and reasonable foreseeable site conditions at the time of our investigation. They cannot necessarily apply to site changes of which this office is unaware and has not had the opportunity to review. Changes in applicable standards may occur because of new legislation or from the broadening of knowledge. Accordingly, findings of this report may be invalidated wholly, or in part, by changes beyond our control.

ACS trusts that the information presented herein provides the data you require. Should you have any questions or comments, please contact ACS. This report, and all available supporting documents and drawings used to prepare the report, have been reviewed by the undersigned, the personnel responsible for this project. The signatory affirms that the Asbestos Investigation documented herein was conducted in substantial conformance with applicable procedures documented in 40 CFR Part 763 – Asbestos, Subpart E – Asbestos Containing Materials in Schools [AHERA, June 24, 1992], and the EPA Guidance Manual “Asbestos Containing Materials in Buildings” (EPA 560/5-85-030a, October, 1985). The investigation by American Compliance Services, LTD, consisted solely of the activities described in this report and is subject to the Exceptions of Assessment, Limitations, and Service Constraints described herein

Travis, California Page 8 of 8

SECTION IX TECHNICAL STAFF SIGNATURES - CERTIFICATE OF REPORT

The following personnel were responsible for this survey. We (I) certify that information contained herein was collected on the dates recorded and the site described in this report.

Wendy Plank Davis, CAC # 01-2904 Certified Asbestos Consultant, Expires 4/4/2026 CDPH Lead I/A, PM, S Certification # 777 Expires 5/18/2025

Sofia Corona Kummer, CSST # 16-5684 Certified Site Surveillance Technician Expiration Date: 8/17/2025 CDPH Lead Certification# 13599 Expiration Date: 04/04/2026

David Kummer, CSST # 08-4363 Certified Site Surveillance Technician Expires 6/19/2025 CDPH Lead Sampling Technician # 20699 Expires 10/27/2025

SAMPLE LOCATION MAP(S)

ASBESTOS

123' 0"

' 0

123' 0"

' 0

24' 0"

' 0

30' 0"

' 0

8'

2' 0"

0' 0"

8'

8' 8"5' 1"

8'

16' 0"

' 0

16' 0"

' 0

01-1 04-8

03-7

03-6

02-5

02-4

01-3

01-2

05-11 P1

05-10

04-9 10-1910-18

09-17

09-16

08-15

08-14

07-13 06-12

13-22

12-21 P4

11-20

P2

P3

P9

P8

P7

P6

P5

Asbestos Floor Plan Travis Air Force Base

Bldg 241 Bay B

9x9 Floor Tile - 5% CH (Mastic is inseparable from VFT without cross contamination)

Restroom

Hall 1

Area 1 Area 2 Stairs

Office

Area 3

Area 4

Hall 3

Hall 2

Shower

LEAD

123' 0"

' 0

123' 0"

' 0

24' 0"

' 0

30' 0"

' 0

8'

2' 0"

' 0

8'

8' 8"5' 1"

8'

16' 0"

' 0

16' 0"

8' 0 "

01-1 04-8

03-7

03-6

02-5

02-4

01-3

01-2

05-11 P1

05-10

04-9 10-1910-18

09-17

09-16

08-15

08-14

07-13 06-12

13-22

12-21 P4

11-20

P2

P3

P9

P8

P7

P6

P5

Lead Plan Travis Air Force Base

Bldg 241 Bay B

Tan and Brown Paint on Windows - 6,500 -91,000 ppm

Restroom

Hall 1

Area 1 Area 2 Stairs

Office

Area 3

Area 4

Hall 3

Hall 2

Shower

Tan on Concrete Wall - 19,000 ppm

Tan on Door Trim - 7,800 ppm

LABORATORY RESULTS

ASBESTOS

LEAD

CODES AND REGULATIONS

CODES AND REGULATIONS

Federal, State, and Local regulations that govern asbestos and lead abatement work or transportation and disposal of asbestos and lead containing waste materials include but are not limited to the following:

CALIFORNIA ASSEMBLY BILLS (CAB)

CAB 040 Yearly Registration of Contractors

CALIFORNIA CODE OF REGULATIONS (CCR)

Title 8 CCR 5208 General Industry - Asbestos Title 17 Division 1, Chapter 8

Accreditation, Certification, and Work Practices in Lead- Related Construction

CCR CARS Carcinogen and Asbestos Registration Sections 340- 344.53, 341.6 Amended, and 341.9 Amended Through 341.14

CCR CSO Construction Safety Orders, Chapter 4, Subchapter 4 CCR ESO Electrical Safety Orders, Chapter 4, Subchapter 5 CCR 1529 Asbestos Construction Standard CCR 1532.1 Lead in Construction CCR 3203 Accident Prevention Program CCR 3204 Access to Employee Exposure and Medical Records CCR 3220 Emergency Action Plan CCR 3221 Fire Prevention Plan CCR 5144 Respiratory Protection Equipment Standard CCR 5194 Hazard Communication Standard CCR 5209 Carcinogen Regulation CCR 6003 Accident Prevention Signs

CALIFORNIA HEALTH SERVICES (CHS) TITLES 22 AND 23, CALIFORNIA

ADMINISTRATIVE CODE DISPOSAL REQUIREMENTS

CHS 25123 Section 25123 CHS 25124 Section 25124 CHS 25143 Section 25143 CHS 25163 Section 25163 CHS 66508 Section 66508 CHS 66510 Section 66510 CHS DIV 4 Division 4, Commencing with Section 66000, Disposal

CALIFORNIA HEALTH AND SAFETY CODE (CHSC)

CHSC 20 Division 20, Commencing with Section 24200

CALIFORNIA LABOR CODE (CLC)

CLC DIVISION 5 Part 1, Commencing with Section 6300

CALIFORNIA PROPOSITIONS (CP)

CP 65 Proposition 65

CALIFORNIA STATE BOARD OF EQUALIZATION (CSBE)

CSBE ETU Excise Tax Unit

CALIFORNIA STATE LICENSE BOARD (CSLB)

CSLB CBPC California Business and Professional Code Sections

7058.5 and 7058.7, Certification

CODE OF FEDERAL REGULATIONS (CFR)

29 CFR 1910.134 Respiratory Protection 29 CFR 1910.141 Sanitation 29 CFR 1910.145 Accident Prevention Signs and Tags 29 CFR 1926.21 Safety Training and Education

29 CFR 1926.55 Gases, Vapors, Fumes, Dusts, and Mists

29 CFR 1926.62 Lead Exposure in Construction

29 CFR 1926.65 Hazardous Waste Operations and Emergency Response

29 CFR 1926.103 Respiratory Protection

29 CFR 1926.59 Hazard Communication 29CFR 1910.1000 Air Contaminants 29 CFR 1926.1101 Asbestos 40 CFR 61-SUBPART A General Provisions 40 CFR 61-SUBPART M National Emission Standard for Asbestos

49 CFR 172 Hazardous Materials Tables and Hazardous Materials Communications Regulations

40 CFR 260 Hazardous Waste Management Systems: General

40 CFR 261 Identification and Listing of Hazardous Waste

40 CFR 262 Generators of Hazardous Waste

40 CFR 263 Transporters of Hazardous Waste

40 CFR 264 Owners and Operators of Hazardous Waste Treatment, Storage, and Disposal Facilities

40 CFR 265 Interim Status Standard for Owners and Operators of Hazardous Waste Treatment, Storage, and Disposal Facilities

40 CFR 268 Land Disposal Restrictions

40 CFR 745 Lead; Requirements for Lead-Based Paint Activities

40 CFR 763 Asbestos Containing Material in Schools 49 CFR 178 Shipping Container Specifications

STATE AND LOCAL REGULATIONS

Regulation 11, Rule 2 Bay Area Air Quality Management District

U.S. DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT (HUD)

Guidelines for the Evaluation and Control of Lead-Based

Paint Hazards in Housing

UNDERWRITERS LABORATORIES INC. (UL)

UL 586 1990 High-Efficiency Particulate Air

CONSULTANTS’ CERTIFICATIONS

!"#$%&"'()*�+,"#�-.$/'(01�&%.0(�#,./%-�0.1�2(�)(%"(-�/3.0�1.�$.04")'�$()1"4"$&1".0�#1&1/#5�6.'3&)(�1,(�"0-"7"-/&%8#�3,.1.�&0-�0&'(�1.�&0.1,()�7&%"-�4.)'�.49.7()0'(01�"##/(-�3,.1.�"-(01"4"$&1".05�:()"4;�1,(�"0-"7"-/&%8#�$()1"4"$&1".0�#1&1/#�2;�#(&)$,"09�4.)�<(&-=>(%&1(-�6.0#1)/$1".0�?).4(##".0&%#�&1�@@@5$-3,5$&59.7A3).9)&'#A$%332�.)�$&%%"09�BCDDE�FGH=<IJ!

K

�� L ���� ������M��L ������L �N�

���L<(&-�O&'3%"09�+($,0"$"&0 <>6=DDDDHPQP RDASHASDSF

TUVW�XYZZ[\