Technical Exhibit 3- KDOT Section 1112 SS-5.pdf

1112 - AGGREGATES FOR SURFACING OR SUBGRADE MODIFICATION

FOR COUNTY SECONDARY ROADS

1100-32

SECTION 1112

AGGREGATES FOR SURFACING OR SUBGRADE MODIFICATION

1112.1 DESCRIPTION

This specification covers types of aggregates used for surfacing or subgrade modification for county secondary roads as shown in the Contract Documents.

1112.2 REQUIREMENTS

a. Composition. Provide one of the types of aggregate for surfacing or subgrade modification for secondary roads as shown in TABLE 1112-1 and 1112-2.

b. Quality1.

Soundness2, minimum (KTMR-21) ............................................................... 0.85 Wear3, maximum (AASHTO T 96) ............................................................... 55% 1Crushed aggregates with less than 10% material retained on the No. 4 sieve (excluding mineral filler supplements) must be produced from a source complying with the official quality requirements of this Section prior to crushing.

2The above requirements for soundness do not apply for aggregates having less than 10% material retained on the No. 4 sieve.

3The above requirements for wear do not apply to aggregates having less than 10% material retained on the No. 8 sieve.

c. Product Control.

(1) Size Requirements. Provide aggregate that complies with TABLE 1112-1. Determine the gradation factor in accordance with the procedures listed in Part V, Section 5.10.5-Fineness Modulus of Aggregates (Gradation Factor).

TABLE 1112-1: GRADATION REQUIREMENTS

Type Material Percent retained

On standard square mesh sieves* Gradation Factor 2” 1 ½” 1” ¾” 3/8” No. 4 No. 8 No. 30 No. 200

SS-3 Crushed Stone 0 0-15 45-85 90-100 92-100 SS-5 Crushed Stone 0 0-5 0-30 45-90 90-100 92-100 SS-7 Sand-gravel 0 0-5 0-20 97-100 4.00 - 5.00** SS-8 Sand-gravel 0 0-5 0-30 92-100 3.75+ SS-9 Sand-gravel 0 0-20 90-100 3.50+ SS-10 Sand-gravel 0 0-5 0-30 90-100 3.25+ SS-14 Limestone gravel 0 93-100 *After removal of all deleterious substances

**For grading factors less than 4.00 but greater than 3.75, provide additional materials as a penalty at a rate of 1.5% for each 0.05 less than 4.00 grading factors. Use a maximum lot size of 500 cubic yards or tons to determine penalty.

Average all tests within the lot to determine penalty.

1112 - AGGREGATES FOR SURFACING OR SUBGRADE MODIFICATION

1100-33

(2) Deleterious Substances. Do not exceed the values for each respective type as shown in TABLE 1112- 2.

TABLE 1112-2: DELETERIOUS SUBSTANCES

Type Material Sticks (wet) Clay Lumps &

Friable Particles Combination1

SS-3 Crushed Stone 2.0 5.0 5.0 SS-5 Crushed Stone 2.0 5.0 5.0 SS-7 Sand-gravel 2.0 5.0 5.0 SS-8 Sand-gravel 2.0 4.0 SS-9 Sand-gravel 2.0 3.0

SS-10 Sand-gravel 2.0 3.0 SS-14 Limestone gravel

1Of any deleterious substances.

d. Stockpiling.

Stockpile and handle aggregates in such a manner to prevent detrimental degradation and segregation, the incorporation of appreciable amounts of foreign material, and the intermingling of stockpiled materials.

1112.3 TEST METHODS

Test aggregates according to the applicable provisions of SECTION 1115.

1112.4 PREQUALIFICATION

Prequalify aggregate sources according to subsection 1101.4.

1112.5 BASIS OF ACCEPTANCE

Aggregates covered by this subsection are accepted based on the procedures described in subsection 1101.5.