Technical Data.pdf

WEBBING,TEXTILE

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

INDIVIDUAL NSN DATA

NSN 8305-00-264-2088; PGC90238

ITEM NAME: WEBBING,TEXTILE

PART NUMBER: PIA-T-5661

CAGE CODE: 1HHQ4; PARACHUTE INDUSTRY ASSOCIATION, INC.

Shall be in accordance with (IAW) Parachute Industry Association

PIA-T-5661D, TAPE AND WEBBING, TEXTILE, WOVEN REINFORCING, COTTON dated 29 June 2015.

For use in the manufacture of aeronautical equipment.

Cloth Name: Plain weave, 1 up and 1 down

Design Type: Flat

Weight: 0.11 ounces per linear yard maximum

Breaking strength: 80 pounds minimum

Fiber material: Cotton

Color: Olive Drab CARC, Chip Number: 34088, IAW AMS-STD-595

Procurement Group Code (PGC): 90238

Width: 0.25 inches ± 0.03 (1/32) inches;

0.22 inches minimum to 0.28 inches maximum

Type: I (Plain weave)

Length and put-up. Unless otherwise specified, tape and webbing shall be furnished on rolls containing 100 ± 10 yards. Each roll shall contain not more than 3 pieces and no piece shall be less than 5 yards long. Tape and webbing 1/2 inch or less in width may be furnished on double-headed spools or tubes containing 500 ± 10 yards. Each spool or plastic tube shall have not more than 6 pieces, and no piece shall be less than 5 yards long.

Unit of issue is a YARD (YD).

NSN 8305-00-268-2411, PGC90238

ITEM NAME: ,,WEBBING, TEXTILE

PART NUMBER: ,,PIA-T-5661

CAGE CODE: ,,1HHQ4; PARACHUTE INDUSTRY ASSOCIATION, INC.

Shall be in accordance with (IAW) Parachute Industry Association PIA-T-5661D, TAPE AND WEBBING, TEXTILE, WOVEN REINFORCING, COTTON dated 29 June 2015.

Cloth Name: Plain Weave, 1 up and 1 down Design Type: Flat Weight: 0.11 ounces per linear yard maximum Breaking strength: 80 pounds minimum Fiber material: Cotton Color: Natural Procurement Group Code (PGC): 90238 Width: 0.25 inches ± 0.03 (1/32) inches;

0.22 inches minimum to 0.28 inches maximum Type: I (Plain weave) Length and put-up. Unless otherwise specified, tape and webbing shall be furnished on rolls containing 100 ± 10 yards. Each roll shall contain not more than 3 pieces and no piece shall be less than 5 yards long.

Tape and webbing 1/2 inch or less in width may be furnished on double-headed spools or tubes containing 500 ± 10 yards. Each spool or plastic tube shall have not more than 6 pieces, and no piece shall be less than 5 yards long.

The unit of issue is a Yard (YD).

Each roll or spool of webbing shall be labeled or ticketed for fiber content in accordance with the Rules and Regulations under the Textile Fiber Products Identification Act.

Each roll, spool or tube of tape or webbing shall be marked for identification in accordance with good commercial practice.

In addition, each roll, spool or tube of tape or webbing shall be clearly and legibly marked with the finisher’s lot number or code, on an attached durable tag.

The textile manufacturer shall properly identify the age of the textile materials by placing a tag on the finished goods or label on the containers identifying the specification to which the material is manufactured, the lot number and the date of manufacture. The date of manufacture is defined as the date (month and year) of the last manufacturing process that affects the physical characteristics of the material.

Identification tickets. Each roll or spool shall have a ticket attached with not finer than 5-ply cotton string doubled to not less than 6 inches long. The tickets shall be made of paperboard not less than 0.015 inch in thickness and the color shall be manila or light in intensity to permit easy reading of printed, stamped or typed markings. The use of handwritten entries is prohibited. The ticket shall have clipped corners at the end where a reinforcing patch (with or without a metal eyelet) is firmly affixed for attaching the tying string. The ticket shall be legibly printed with water insoluble ink with the following information:

- Stock number

- Nomenclature

- Specification number

- Yardage

- Contract number and date of manufacture (month and year)

- Contractor's name

- Name of contracting agency.

TEST REPORTS AND COMPONENT CERTIFICATIONS IN ACCORDANCE WITH

DLA TROOP SUPPORT CLOTHING & TEXTILES ADDITIONAL QUALITY ASSURANCE

REQUIREMENTS, Revision 1 dated 1 August 2021 (superseding DPSCM-4155.3 dated 3 November 1997) ARE REQUIRED WITH ALL CONTRACT COMPONENT LOTS.

*In lieu of the abovenamed requirement, if the total contract award does NOT exceed $100,000, the contract awardee may submit a Certificate of Compliance (CoC) per 3.1.3 of the DLA Troop Support Clothing and Textiles (C&T) Additional Quality Assurance Requirements (AQAR), Revision 1 dated August 2021.*

**Please note, however, use of the CoC in lieu of submitting the certified test reports, is subject to approval by the Contracting Officer identified on the solicitation, purchase order, and/or the contract.**

SOURCES OF COMPONENT MATERIALS SHALL BE IDENTIFIED<(>,<)>

INCLUDING APPLICABLE SPECIFICATIONS, AND SHALL NOT

BE CHANGED THROUGHOUT THE LIFE OF THE CONTRACT

WITHOUT REQUEST AND APPROVAL BY THE DLA TROOP

SUPPORT CONTRACTING OFFICER THROUGH MODIFICATION

TO THE CONTRACT.

RESPONSIBILITY OF INSPECTION. THE CONTRACTOR IS

RESPONSIBLE FOR THE PERFORMANCE OF ALL INSPECTION<(>,<)>

EXAMINATION, AND TEST REQUIREMENTS SPECIFIED

HEREIN AND IN THE SITED SPECIFICATIONS AND CONTRACT.

THE GOVERNMENT RESERVES THE RIGHT TO PERFORM ANY

OF THE INSPECTIONS, EXAMINATIONS AND TESTS AS

DEEMED NECESSARY TO ENSURE SUPPLIES AND SERVICES

CONFORM TO PRESCRIBED REQUIREMENTS.

RT001: MEASURING AND TEST EQUIPMENT

GOVERNMENT LABORATORY TESTING OF COMPONENTS FOR ACCEPTANCE PURPOSE

FOR PHYSICAL (NON-SHADE) TESTING:

*Only applicable if the total contract award exceeds $100,000*

**In lieu of the abovenamed requirement, if the total contract award does NOT exceed $100,000, the contract awardee may submit a Certificate of Compliance (CoC) per 3.1.3 of the DLA Troop Support Clothing and

Textiles (C<(>&<)>T) Additional Quality Assurance Requirements (AQAR), Revision 1 dated August 2021.** THE VENDOR SHALL NOTIFY THE DLA Product Test Center -- Analytical

FOURTEEN (14) CALENDAR DAYS TO THIRTY (30) CALENDAR DAYS IN ADVANCE OF

WHEN LOTS ARE TO BE PRESENTED FOR SAMPLING AT THE ADDRESS BELOW.

THE CONTRACTOR'S APPROVED QUALIFIED LABORATORY WILL BE REQUIRED TO

FORWARD A COMPLETED TEST REPORT FOR EACH LOT OF COMPONENTS TO THE

ADDRESS BELOW. THE SUPPLIER'S SOURCE SAMPLING REPRESENTATIVE WILL

PROVIDE THE COMPLETED DD FORM 1222 dated March 2021 TO THE LABORATORY TO

BE SUBMITTED WITH THE COMPLETED TEST REPORT. TEST REPORTS SHALL NOT BE

OLDER THAN NINETY (90) CALENDAR DAYS.

LOT NOTIFICATIONS AND SOURCE SAMPLING DD1222s/TEST REPORTS SHALL BE

FORWARDED TO:

paactlab@dla.mil

SAMPLES FOR PHYSICAL TESTING WILL ONLY BE FORWARDED UPON REQUEST TO:

DLA Product Test Center -- Analytical 700 Robbins Avenue, BLDG 5D Philadelphia, PA 19111 EMAIL: paactlab@dla.mil

NOTE: PERMIT 45 CALENDAR DAYS

SHADE EVALUATION OF CONTRACTOR FURNISHED MATERIALS:

SHADE SAMPLING IS REQUIRED (Natural color is not required for shade testing)

The color of the test specimen shall match the standard sample when viewed using AATCC Evaluation Procedure 9, Visual Assessment of Color Difference of Textiles, Option C (2017e)<(>,<)> with sources simulating artificial daylight D65 illuminant with a color temperature of 6500 (+/- 200)K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)K.

FOR SHADE TESTING: THE COMPLETED HARDCOPY DD FORM 1222

(July 2024 edition) AND THE SWATCHES SHALL BE FORWARDED TO:

DLA Product Testing Center Analytical 700 Robbins Avenue, BLDG 5D Philadelphia, PA 19111 ATTN: Andrew Gabriele

EMAIL: andrew.gabriele@dla.mil PHONE: 267-990-3666 (Government cell phone)

NOTE: PERMIT 30 CALENDAR DAYS.

Identification of Testing Sites. Unless the contract mandates a Government laboratory be used to conduct testing, the prime contractor shall identify all testing sites that will perform any test required by the terms of the contract, including end item testing.

Any laboratory proposed by the contractor is subject to the approval of the contracting officer. Testing facilities shall be subject to on-site witnessing of testing by the Government. The use of a laboratory previously approved by the Government is not a guarantee that testing will be performed properly, nor does it relieve a contractor from the contractual obligation to present conforming supplies accompanied by true, accurate, and valid test results.

Certification of Testing Sites. The prime contractor shall identify a technical point of contact for the testing site and provide current contact information. The prime contractor should alert the technical point of contact that the certification process has begun. A current ISO 17025 accreditation whose scope encompasses the contractual testing or equivalent will be accepted. When a testing site and its contact information are provided to DLA Contracting and the DLA Product Specialist, the product specialist will initiate a request for the DLA Product Test Center (DLA-PTC) to certify the lab. This request will be managed via an internal DLA Troop Support process.

In the absence of an appropriate ISO 17025 accreditation, the DLA-PTC will compare all required testing in the contract to the commercial lab capability. If the testing facility is new and/or unknown to the DLA-PTC, a lab certification survey (DLA Form 6005) will be provided for submission.

If the DLA-PTC has a lab survey on file that is less than 3 years old, that survey will be used for the initial evaluation. The DLA-PTC may ask for additional information or clarifications. If the laboratory survey on file is over 3 years old, a new form will be sent out for the testing facility to fill out. During a contract, the laboratory may be asked to fill out another lab survey when the original survey becomes older than 3 years.

Note: The Qualified Laboratories List (QLL) previously maintained by DPSC has been canceled. No testing facility should refer to their previously issued QLL number.

Approval. If the testing facility and its named subcontractors meet the capability of the required testing, the DLA-PTC will notify the DLA Troop Support Product Specialist. Once approved by contracting, the testing facility becomes the Place of Performance and is placed in the contract.

Disapproval. If a testing facility does not meet the testing capability as per the specifications, the prime contractor is asked to submit another laboratory, and the process starts anew.

Note: DLA will require a total of 45 calendar days from the date of the receipt of the request to add a certified testing location to the date the requestor (contractor) is provided a decision of the laboratory certification.

Identification of Testing Sites. Unless the contract mandates a Government laboratory be used to conduct testing, the prime contractor shall identify all testing sites that will perform any test required by the terms of the contract, including end item testing.

The prime contractor shall identify a technical point of contact for the testing site and provide current contact information to DLA Contracting and the DLA Product Specialist. The prime contractor should alert the technical point of contact that the certification process has begun.

Note: DLA will require a total of 45 calendar days from the date of receipt of the request to add a certified testing location to the date the requestor (contractor) is provided a decision of the laboratory certification.

For more details on the lab certification process, see the C<(>&<)>T Additional Quality Assurance Requirements document, which is incorporated by reference into this contract.

Please also navigate to https://www.dla.mil/Troop-Support/Product-Test-Center/ for more information regarding the DLA Troop Support Product Test Center (PTC).

Further, the PTC can also be contacted via email at paactlab@dla.mil or by phone at (215) 737-3241.

CRITICAL APPLICATION ITEM

IAW BASIC STD NR MIL-STD-129R(3)

REVISION NR R DTD 02/25/2023

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 14153 C&T-ADDITQAR

REVISION NR 1 DTD 08/01/2021

PART PIECE NUMBER:

IAW REFERENCE SPEC NR MIL-DTL-15011K(2) NOT 1

REVISION NR K DTD 04/29/2025

PART PIECE NUMBER:

IAW REFERENCE SPEC NR MIL-P-43334C

REVISION NR C DTD 09/30/1986

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-147E(3)

REVISION NR E DTD 09/05/2024

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-1916 NOT 2

REVISION NR DTD 06/05/2014

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-2073-1E(4) NOT 1

REVISION NR E DTD 06/27/2024

PART PIECE NUMBER:

IAW REFERENCE UNK FED-STD-191A(6) NOT 7

REVISION NR A DTD 08/09/2000

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD ASQ Z1.4 (R 2018)

REVISION NR DTD 01/01/2003

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD PIA-T-5661D

REVISION NR D DTD 06/29/2015

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-3064 NOT 1

REVISION NR DTD 04/04/2024

PART PIECE NUMBER:

PKGING DATA - MIL-STD-2073-1E

QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00

WRAP MAT:00 CUSH/DUNN MAT:AD CUSH/DUNN THKNESS:C

UNIT CONT:A2 OPI:O

PACK CODE:U

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:ZZ -ZZ Special Requirements

PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING

REQUIREMENTS FOR PROCUREMENT

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

INSPECTION AND ACCEPTANCE AT DESTINATION.

SECTION D - PACKAGING AND MARKING

ALL WOOD PACKAGING MATERIAL (WPM) USED MUST MEET

REQUIREMENTS OF INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

(ISPM) 15, "GUIDELINES FOR REGULATING WOOD PACKAGING MATERIALS IN

INTERNATIONAL TRADE." DOD SHIPMENTS INSIDE AND OUTSIDE OF THE UNITED

STATES MUST MEET ISPM 15 WHENEVER WPM IS USED TO SHIP DOD CARGO.

ALL WPM SHALL COMPLY WITH THE OFFICIAL QUALITY CONTROL PROGRAM FOR HEAT

TREATMENT (HT) OR KILN DRIED HEAT TREATMENT (KD HT) IN ACCORDANCE WITH

AMERICAN LUMBER STANDARD COMMITTEE<(>,<)>

INCORPORATED (ALSC) WOOD PACKAGING MATERIAL PROGRAM AND WPM

ENFORCEMENT

REGULATIONS (SEE HTTP://WWW.ALSC.ORG/).

ALL WPM SHALL INCLUDE CERTIFICATION/QUALITY MARKINGS IN

ACCORDANCE WITH THE ALSC STANDARD. MARKINGS SHALL BE PLACED IN AN

UNOBSTRUCTED AREA THAT WILL BE READILY VISIBLE TO

INSPECTORS. PALLET MARKINGS SHALL BE APPLIED TO THE STRINGER OR BLOCK ON

DIAGONALLY OPPOSITE SIDES OF THE PALLET AND BE

CONTRASTING AND CLEARLY VISIBLE. ALL CONTAINERS SHALL BE

MARKED ON A SIDE OTHER THAN THE TOP OR BOTTOM, CONTRASTING

AND CLEARLY VISIBLE. ALL DUNNAGE USED IN CONFIGURING AND/OR

SECURING THE LOAD SHALL ALSO COMPLY WITH ISPM 15 AND BE MARKED WITH AN

ASLC APPROVED DUNNAGE STAMP.

THE OVERALL PACKAGING AND PRESERVATION, IF APPLICABLE, SHALL CONFORM TO

MIL-STD-2073-1E (WITH CHANGE 4 DATED 22 APRIL 2019) STANDARD PRACTICE

FOR MILITARY PACKAGING FOR SHIPMENTS TO THE DEPARTMENT OF DEFENSE.

UNIT CONTAINER:

EACH ROLL OF THE WEBBING SHALL BE INDIVIDUALLY PACKAGED IN ANY BAG USED

BY THE VENDOR.

INTERMEDIATE CONTAINER: NOT REQUIRED; THE USE OF INTERMEDIATE PACKAGING

IS ENCOURAGED PARTICULARLY WHEN SUCH USE ENHANCES HANDLING AND

STORAGE.

IF USED, VENDOR SHALL USE ANY SUITABLE FIBER BOX INCLUDED IN TABLE J-VII

OF MIL-STD-2073-1E CHANGE 4 (PDF Pages 185/214) MAY BE USED (SEE ALSO J.4.9.1).

EXTERIOR CONTAINER: SHALL BE STYLE: REGULAR SLOTTED BOX (RSC)<(>,<)>

TYPE: CORRUGATED FIBERBOARD (CF), VARIETY DOUBLEWALL FIBERBOARD (DW),

CLASS: DOMESTIC, GRADE: 275 WITH A SINGLE WALL LINER OR DW ECT GRADE 48,

MADE TO THE REQUIREMENTS OF ASTM D5118M, STANDARD PRACTICE FOR

FABRICATION OF FIBERBOARD SHIPPING BOXES TO INSURE MEETING THE

REQUIREMENTS OF A PACK THAT WILL SUPPORT

RE-TRANSPORT, STORAGE, STACKING, ETC.

THE PACKAGING CONTAINER SHALL BE SUFFICIENT TO PROVIDE PROTECTION DURING

TRANSPORT AND STORAGE AND ARRIVE AT DESTINATION IN THE SAME CONDITION AS

ORIGIN.

PACKAGED COMPONENTS SHALL BE BULK PACKAGED IN A

THAT WILL SUPPORT RE-TRANSPORT, STORAGE, STACKING, ETC.

REFERENCE ASTM INTERNATIONAL DESIGNATION D1974M (STANDARD PRACTICE FOR

METHODS OF CLOSING, SEALING, AND REINFORCING FIBERBOARD BOXES, WHICH

DESCRIBES SEVERAL METHODS FOR CLOSING, SEALING, AND REINFORCING

FIBERBOARD (SOLID AND CORRUGATED) SHIPPING BOXES USED FOR SHIPMENT.

A PRESSURE SENSITIVE IDENTIFICATION LABEL SHALL ATTACH TO

EACH PACKAGING BOX OF THE COMPONENT.

THE PACKAGING CONTAINER SHALL BE SUFFICIENT TO PROVIDE PROTECTION DURING

TRANSPORT AND STORAGE AND ARRIVE AT DESTINATION IN THE SAME CONDITION AS

ORIGIN.

SURFACE OF THE PALLET. WHEN SPECIFIED PALLETIZATION IS REQUIRED,

COMPONENTS SHALL BE PALLETIZED ON A FOUR-WAY ENTRY PALLET IN ACCORDANCE

WITH LOAD TYPE I OR IA, AS

APPLICABLE, OF MIL-STD-147E, CHANGE 2 DATED 27 JUNE 2019.

PALLETIZATION. Palletization shall be in accordance RP001, Section 3.

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED

COMMERCIAL BONDING MATERIALS. PALLET LOADS SHALL

CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL

QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT

POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL

BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED

IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN.

AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON

PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY.

SAID CARTON SHALL BE CLEARLY MARKED "SHORT"

OR "OVER".

All unit, intermediate and shipping containers shall be marked in accordance with MIL-STD-129R, with Change 3 dated 25 February 2023.

IN ADDITION TO SPECIAL MARKING REQUIRED<(>,<)>

INTERIOR (UNIT) PACKS, INTERMEDIATE CONTAINERS<(>,<)>

SHIPPING CONTAINERS AND PALLETIZED UNIT LOADS

SHALL BE MARKED FOR SHIPMENT, STOWAGE, AND STORAGE IN ACCORDANCE WITH

MIL-STD-129R CHANGE 3 DATED 25 FEBRUARY 2023.

GUIDANCE FOR THE REQUIRED IDENTIFICATION TEXT MARKINGS OF THE UNIT,

INTERMEDIATE, AND EXTERIOR CONTAINERS ARE FOUND ON PAGES 24 TO 28 WITHIN

MIL-STD-129R WITH CHANGE 3 DATED 25 FEBRUARY 2023.

Identification text marking on unit packs and intermediate containers will be located so the marking can be easily read and to ensure that the marking will not be destroyed when the pack or container is opened for inspection or until its contents have been used. The marking surface of a unit pack shall be the outermost wrap, bag, or container of the unit pack.

Lot number as an identification text marking is required on all unit packs and intermediate containers.<(>,<)>

The shipment number and container number are required on all exterior containers, palletized unit loads, and unpacked items. See MIL-STD-129R with Change 3, 5.1.2. f.(3) for more details.