Tech Data - Womens Jumper White.pdf

JUMPER, WOMAN'S, WHITE

ADDITIONAL INFORMATION FOR NCTRF-PD 24949C:

PATTERN DATE: 22 December 2023

STANDARD SAMPLE OF CLOTH, TWILL, POLYESTER, WHITE SHADE NUMBER 3006,

UNDER MIL-C-87052, IS AVAILABLE AND APPLICABLE FOR SHADE, COLORFASTNESS

TO LIGHT, LAUNDERING, BLEACHING, DRY CLEANING, PERSPIRATION TO ALKALINE,

ACID AND FINISH UNDER PIECE NO. 17027

AN EMBROIDERY FILE FOR THE STAR REPLACES THE DRAWING "STITCH ENLARGEMENT

FOR 5-POINTED STAR (3/4 INCH DIAMETER)" 16-1-16021.

\\phlli210\udn7415\system\desktop\Emroidered Star.DST

NOMENCLATURE:CROWTACK STITCH ENLARGEMENT : DRAWING NUMBER 01-NCTRF-15

Dated May 27, 2015

ADDITIONAL INFORMATION FOR NCTRF PD 87037:

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

A. THIS SOLICITATION/AWARD CONSISTS OF THE FOLLOWING DOCUMENTS, EXHIBITS, AND OTHER

ATTACHMENTS.

B. DLA TROOP SUPPORT CLOTHING AND TEXTILES ADDITIONAL QUALITY ASSURANCE REQUIREEMENTS DATED AUGUST 2021, SUPERSEDES DSCP 4155.3, QUALITY SYSTEMS REQUIREMENTS, DATED OCTOBER 2018.

THE CONTRACTOR SHALL STAMP LEGIBLY WITH INDELIBLE INK THE LOT NUMBER ON EACH END ITEM

AND OUTER CONTAINER IN THE LOT.

THE INSPECTION LEVELS AND ACCEPTABLE QUALITY LEVELS (AQL'S) EXPRESSED IN

DEFECTS PER 100 UNITS FOR VISUAL AND DIMENSIONAL EXAMINATIONS SHALL BE

AS FOLLOWS:

INSPECTION

AQL'S LEVEL

FOR VISUAL EXAM. IN 4.4.3

CRITICAL

MAJOR 1.0 III

MINOR 4.0 III

TOTAL (CRITICAL,MAJOR,MINOR) 10.0 III

FOR DIMEN. EXAM. IN 4.4.4

ONE CLASS 2.5 S-3"

THE AQL SHALL BE 2.5 DEFECTS PER 100 UNITS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE OR FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII

(PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE

TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

file://phlli210/udn7415/system/desktop/Emroidered

ADDITIONAL INFORMATION FOR A-A-52071:

PAGE 1, DOCUMENT TITLE, DELETE "COTTON".

1.1, AFTER :CLASS 3- DYED", ADD "CLASS 4-SOLUTION

DYED POLYESTER".

2.1, LINE 1, AFTER "COTTON YARNS", ADD EXCPT CLASS

4 SHALL BE POLYESTER".

2.2, AFTER LINE 1, ADD "THE CLASS 4 TAPE SHALL BE

SOLUTION DYED ONLY."

PAGE 2, 2.3, LINE 2, AFTER "CLASS 2", ADD "AND CLASS 4".

2.4, LINE 1, DELETE "1,2, AND 3" AND SUBSTITUTE "1,2,3,

AND 4".

ADDITIONAL INFORMATION FOR A-A-52094B:

ADDITIONAL INFORMATION FOR A-A-50198A

THREAD, GIMP, COTTON, BUTTONHOLE

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

BOXES USED FOR SHIPPING SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-129,

"MARKING FOR SHIPMENT AND STORAGE".

PALLETIZATION SHALL BE IN ACCORDANCE WITH MIL-STD-147, "PALLETIZED UNIT

LOADS".

DEVELOPMENT AND APPLICATION OF PACKAGING REQUIREMENTS SHALL BE IN

ACCORDANCE WITH MIL-STD-2073-1, "DOD MATERIALS PROCEDURES FOR

DEVELOPMENT AND APPLICATION OF PACKAGING REQUIREMENTS".

PACKAGING REQUIREMENTS CODES SHALL BE IN ACCORDANCE WITH MIL-STD-2073-2,

"PAKAGING REQUIREMENTS CODE".

COMMERCIAL ITEM DESCRIPTION A-A-52071

DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR

USE IN PLACE 0F DDD-T-86H.

"THE REQUIREMENT FOR THE HERRINGBONE TAPE IS TYPE I, 3/16 INCH WIDTH AND

58 PICKS PER INCH FROM TABLE I. PHYSICAL REQUIREMENTS."

ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING

BOXES, AND ASTM-D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING

AND REINFORCING FIBERBOARD SHIPPING CONTAINERS.

(ref. T0857 - 6/15/06)

ADDITIONAL INFORMATION FOR MIL-C-87052:

INTERIM SPECIFICATION CHANGES TO MIL-C-87052B:

PAGE 6, PARA. 4.4.2.1, LINE 13, DELETE "25" AND

SUBSTITUTE "17", LINES 15 & 18, DELETE "38" AND

SUBSTITUTE "26".

ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN

CANCELLED AND REPLACED BY ASTM-D-6193, 4/98

STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE

TO FED-STD-751.

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2

STANDARD INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product", or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes".

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207- 6028.)

MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE

MILITARY MARKING FOR SHIPMENT AND STORAGE - DATED

19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA

TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS

OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER

TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR MIL-STD-2073-1:

NO ADDITIONAL INFORMATION FOLLOWS

(Ref. T0898)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2

18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2

STITCH ENLARGEMNET DRAWING FOR CROWTACK:

01-NCTRF-15 CROWTACK FOR JUMPERS

5/27/2015

THIS IA A TYPE II (CODE 7) SHELF LIFE ITEM

WITH A SHELF LIFE OF 36 MONTHS (EXTENDABLE)

NOTE: PARAGRAPH 5.2.1 OF

MIL-STD-129P W/CHANGE 3 IS APPLICABLE.