TECH DATA PGC91754-.pdf

Pa ge

TECH DATA

PGC91754

NSN 8305-01-057-9818

CLOTH, TROPICAL, POLYESTER/WOOL, AIR FORCE BLUE SHADE 540 TYPE III CLASS 3

STANDARD SAMPLE IS IDENTIFIED AS ROLL NUMBER 18-02 AND IS APPLICABLE FOR SHADE, FINISH AND

COLORFASTNESS AND GOOD LIGHTFASTNESS AT 40 SPH. SPONGED.

SPEC: MIL-DTL-21115L DATED 24 JUNE 2005

MOTHPROOFING SPEC: MIL-DTL-43665D DATED 2 SEPT 2020

THE CLOTH SHALL BE MOTHPROOFED IAW MIL-DTL-43665D.

CERTIFICATE OF COMPLIANCE IS APPLICABLE FOR WOOL

GRADING IN THE TOP

8305-01-057-9818 Shall be made in accordance with SPEC: MIL-DTL-21115L DATED 24 JUNE 2005

The cloth shall be sponged/mothproofed in accordance with MIL-DTL-43665D, DATED 2 SEPT 2020.

(REF.91752)

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND

QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A

FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-

MANUFACTURERS)

DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements Revision 1 DATED August 2021 applies

T0046: 52.246-15 CERTIFICATE OF CONFORMANCE

T0795: ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

SERVICES FOR COLD WATER SPONGING AND SEMI-DECATING OF: CLOTH, TROPICAL, POLY/WOOL, TYPE III CLASS 3 BLUE AF 540

1. Purpose of the Servicing: The condition of the cloth to be serviced is the state in which it was presented to and accepted by the Government for the original producer, as fully finished and meeting the requirements of the applicable specification. It is the purpose of servicing of this cloth to remove all tensions and to stabilize ("set') the cloth in that state, so that it will drape freely in the tailoring of the end-item garment.

2. Wetting Out: The cloth shall be led into wetting-out tank full width and thoroughly wet out while in motion. The water shall be suitably son and clean. A wetting agent shall be used to assure thorough saturation of the cloth. Wet - out cloth shall not be left standing and shall be fully processed once it saturation of the cloth. Wet out cloth shall not be left standing and shall be fully processed once it is wet-out. There shall be no water or mineral stains or drying marks or bars. The water temperature shall be uniform and selected to suit the fabric in question and to assure maximum cloth stability.

3. Drying: The cloth that has been wet out per paragraph 2 above shall be dried full width. The drying arrangement shall be such that the cloth is not held under tension either in length or width and can freely relax in all directions during the drying operations. The drying system used shall lend itself to temperature control and shall be properly ventilated lo assure uniform heat distribution. The system shall assure that the cloth emerges from it fully dried, free from stains, discolorations and mineral deposits. The cloth shall not touch metal objects or otherwise overheated surfaces and the cloth shall not be allowed to remain in the drying device during any machine stoppage. Extreme care shall be taken to precluded any scorches of the cloth, or any over drying.

4. Conveyance: The cloth emerging from the dryer shall be loosely Oat-folded on the conveyance used to move the cloth to semi-decating. The cloth shall be given an opportunity to cool off without having excessive layers of cloth from other pieces bearing down on the cloth.

Care shall be taken that cloth is not exposed to any areas where dripping of water, oil, steam or other pollutants endangers its cleanness.

5. Semi-Decating: The sponged and dried cloth shall be "set" by steam treatment in a semi-decating device. The cloth shall be rolled, full width between a cloth "mantle" over a perforated metal cylinder. Care shall be taken to roll the cloth between the mantle, free from any wrinkles;

selvages fully flattened and with only enough tension to preclude distortions, bias, bowing filling or other deficiencies. All due care shall be taken to avoid seam marks, and the mantle shall be free from any protrusions that might impress themselves on the cloth serviced. Steam shall be uniformly flown from the metal cylinder through the mantle onto the cloth to be serviced. Care shall be taken to assure that there shalt be no steam condensation onto the cloth, and that the serviced cloth shall be free from decating marks.

6. Put-Up and Measuring and Roll Marking: The cloth, which has been sponged and semi-decated shall be put on fiberboard tubes of a length at least equal to the width of the cloth. The cloth shall be rolled firmly but without tension. The cloth being put-up shall be measured by an accurate, recently calibrated device that is in direct contact with the cloth while running over a hard service. Each piece of cloth shall also be measured in the width, between selvages, at least at three points along its length. The lowest of these three measurements, rounded down to the nearest full inch shall be the sponged width for the respective roll. The sponge length and width shall then be entered at the space provided on the original piece ticket. If for any reason, the original piece ticket has become unavailable, a new piece ticket shall be securely attached. Item description, applicable National Stock Number (NSN), and contract data (copies from a piece ticket in the same batch) and piece number (which may be obtained from the indelible marking at the end of the roll), shall then be legibly marked on the new ticket.

7. Preparation for Delivery: 8.1 Pres/Pack to ASTM-D-3951 Each roll shall be packed in a polyethylene bag as a minimum 8.2 Marking: MIL-STD-2073-ID, dated DECEMBER 15, 1999.

8. Unusable Materials: Fabrics found by the contractor to be obviously unusable, when detected, shall be set aside and not include in the inventory list of sponged cloth. The unusable material shall be returned with each shipment of sponged cloth clearly marked "Defective Cloth

– Unsponged."

9. Tabulation: For each lot serviced, tabulation shall accompany the shipping document (DD250) showing piece number, length and width of each roll serviced. DD250 shall show total yardage received, total yardage defective (if applicable), total yardage sponged. Payment shall be made on yardage received and sponged. Payment shall be made on yardage received and sponged. No payments shall be made for defective yardage, which is not sponged.

10. Plant Visits: The Government reserves the right to visit the contractor's plant at any time during working hours to observe performance of the contract and/or to examine the end product. In plant visits and observations shall be confined to:

a. Ascertaining that material furnished the contractor by the Government is properly stored and safeguarded from damage before, during and after the completion of the services hereunder.

b. Assuring, by actual observations, that the specified operations be performed.

11. Specification and Standards:

SPEC:MIL-DTL-21115L DATED 24 JUNE 2005.

12. Quality Assurance Provisions for Commercially Sponged Cloth:

a. The sponged and semi-decated cloth shall be inspected by the Government for sponging defects, semi-decating defects, markings, and width/length measurements.

b. Yard by Yard Examination - The yard-by-yard examination shall be as specified below. The sample size shall be in accordance with the following:

Lot Size (yards) Sample size rolls 500 or less 8 501 to 3,200 13 3,201 to 35,000 20 35,001 to 500,000 32 500,001 to over 50

The following defect, when present shall be scored four points for each yard in which it occurs.

-Width less than specified

Except for the above defect, all defects shall be scored and assigned demerit points as follows:

-defects 3 inches or less in any dimension - one point -defects exceeding 3 inches to 6 inches in any dimension - two points -defects exceeding 6 inches to 9 inches in any dimension - three points -defects exceeding 9 inches in any dimension - four points

c. The following conditions after sponging and semi-decating shall be scored as defects:

-unclean overall -ends of cloth unmarked -water or mineral stains -drying marks or bars -scorch marks permanent creases -incorrect label or marking

d. Total yardage in sample

- The lot shall be unacceptable if the total of the actual length of the rolls in the sample is less than the total of the lengths marked on the roll tickets.

e. Quality conformance inspection - The lot shall be unacceptable if the point count exceeds 2.5 points per 100 square yards when examined as specified in paragraphs b. and c. above.

Additional information for:MIL-STD-655D: Provisions for Evaluating Quality of Cloth

Interim changes to: MIL-STD-655D:

PAGE 3, PARA 4.1, ADD "QUALITY LEVEL 7".

PAGE 5, TABLE I, UNDER QUALITY LEVEL"7", ADD UNDER ENTIRE SAMPLE "7

POINTS PER 100 SQ. YARDS", ADD UNDER INDIVIDUAL ROLLS "10 POINTS PER 100

SQ. YDS." (Ref. T0319)

The demerit points per 100sq yds shall not exceed a quality level 12

IAW MIL-STD-655D.

An RFID inlay shall be added to the barcode paper hang tag attached to each item. Where the use of self-adhesive bar-code labels are authorized, the RFID inlay may be added to the self-adhesive label in lieu of a paper hang tag. All other contract barcode and hang tag requirements still apply.

The RFID inlay should be passive Gen2 with a frequency range between 860 and 960 MHz. The RFID antenna should be Avery/Dennis AD222 or comparable with ISO/IEC 18000-C EPCglobal C1G2 Protocol and an EPC memory allocation containing a 96 bit EPC Number. The data linking the EPC number to the NSN and quantity unit pack must be exportable to VIM/ASAP.

The bar code of the EPC Number must be printed at the bottom of the tag along with the human readable version below the bar code.

In addition to defects applicable to the paper tag and barcoding element, the RFID tag shall be examined for the defects listed below:

RFID Inlay omitted

RFID Inlay not secure

RFID Inlay not laying flat when packaged

RFID Inlay not readable with RFID scanner

RFID Inlay or configuration not as specified

The manual "Item-Level Passive RFID Technology Manufacturer's

Information Guide" provides guidance on RFID implementation and is available from the contracting officer.

SHADE EVALUATION OF CONTRACTOR FURNISHED MATERIALS:

Government Acceptance Testing. Unless otherwise stated in the contract, testing performed at the DLA PTC for acceptance purposes will be completed in forty five (45) calendar days. The contract delivery requirements are based on the assumption that DLA Troop Support and the DLA PTC will require a total of 45 calendar days from the date of the receipt of samples at the Government laboratory to the date the completed test results are mailed to the contractor.

If this time frame is exceeded, the contract delivery schedule will be extended by the number of additional days needed to complete the testing, provided the contractor can establish that the delay in its delivery was caused by the Government exceeding the prescribed time. The foregoing provision for the extension of delivery schedules is exclusive and the Government shall not be liable to suit for breach of contract by reason of any delay of the Government in providing test results.

Shade Evaluation. Shade Evaluation is Acceptance Testing; each lot must be submitted for evaluation.

Lots shall not be shipped until shade is approved by Government. The prime contractor will require the fabric or component supplier to present to the source QAS the complete lot prepared for shipment, a set of tally sheets by shipment listing case numbers, roll numbers, and yardage of each roll and a shade swatch (header) from each roll with roll and case numbers identified on each swatch.

The following sampling procedure will be followed unless otherwise specified.

- SHADE SAMPLING IS APPLICABLE

The color and appearance of the shade sample swatch shall match the standard sample when viewed using the AATCC EP 9, Option C, with a primary light source simulating the spectral quality of average daylight, CIE illuminate D65, with a color temperature of 6500 K (±200 K) illumination of 100 (±20) foot candles. The shade sample swatch shall also be an approximate match to the standard sample with a secondary source simulating the spectral quality of incandescent lamplight, CIE illuminant A, with a color temperature of 2856 K (±200 K).

FOR SHADE TESTING: THE COMPLETED HARDCOPY DD FORM 1222 AND THE SWATCHES SHALL

BE FORWARDED TO:

DLA Product Testing Center Analytical 700 Robbins Avenue, BLDG 5D Philadelphia, PA 19111 EMAIL: paactlab@dla.mil

PHONE: 215-737-6121

NOTE: PERMIT 30 CALENDAR DAYS.

mailto:paactlab@dla.mil

FOR PHYSICAL (NON-SHADE) TESTING:

THE VENDOR SHALL NOTIFY THE DLA Product Test Center -- Analytical FOURTEEN (14)

CALENDAR DAYS TO THIRTY (30) CALENDAR DAYS IN ADVANCE OF WHEN LOTS ARE TO BE

PRESENTED FOR SAMPLING AT THE ADDRESS BELOW.

THE CONTRACTOR'S APPROVED QUALIFIED LABORATORY WILL BE REQUIRED TO FORWARD A

COMPLETED TEST REPORT FOR EACH LOT OF COMPONENTS TO THE ADDRESS BELOW. THE

SUPPLIER'S SOURCE SAMPLING REPRESENTATIVE WILL PROVIDE THE COMPLETED DD FORM

1222 dated March 2021 TO THE LABORATORY TO BE SUBMITTED WITH THE COMPLETED TEST

REPORT. TEST REPORTS SHALL NOT BE OLDER THAN NINETY (90) CALENDAR DAYS.

LOT NOTIFICATIONS AND SOURCE SAMPLING DD1222s/TEST REPORTS SHALL BE FORWARDED

TO:

paactlab@dla.mil

SAMPLES FOR PHYSICAL TESTING WILL ONLY BE FORWARDED UPON REQUEST TO:

DLA Product Test Center -- Analytical 700 Robbins Avenue, BLDG 5D Philadelphia, PA 19111 EMAIL: paactlab@dla.mil

NOTE: PERMIT 45 CALENDAR DAYS

SHADE EVALUATION OF CONTRACTOR FURNISHED COMPONENTS

Contracts awarded under this solicitation shall require shade evaluation of Contractor furnished components in accordance with DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirement(Revision1 dated: August 2021)

Identification of Testing Sites. Unless the contract mandates a Government laboratory be used to conduct testing, the prime contractor shall identify all testing sites that will perform any test required by the terms of the contract, including end item testing.

Any laboratory proposed by the contractor is subject to the approval of the contracting officer.

Testing facilities shall be subject to on-site witnessing of testing by the Government. The use of a laboratory previously approved by the Government is not a guarantee that testing will be performed properly, nor does it relieve a contractor from the contractual obligation to present conforming supplies accompanied by true, accurate, and valid test results.

Certification of Testing Sites. The prime contractor shall identify a technical point of contact for the testing site and provide current contact information. The prime contractor should alert the technical point of contact that the certification process has begun. A current ISO 17025 accreditation whose scope encompasses the contractual testing or equivalent will be accepted.

When a testing site and its contact information are provided to DLA Contracting and the DLA Product Specialist, the product specialist will initiate a request for the DLA Product Test Center mailto:paactlab@dla.mil

(DLA-PTC) to certify the lab. This request will be managed via an internal DLA Troop Support process.

In the absence of an appropriate ISO 17025 accreditation, the DLA-PTC will compare all required testing in the contract to the commercial lab capability. If the testing facility is new and/or unknown to the DLA-PTC, a lab certification survey (DLA Form 6005) will be provided for submission.

If the DLA-PTC has a lab survey on file that is less than 3 years old, that survey will be used for the initial evaluation. The DLA-PTC may ask for additional information or clarifications. If the laboratory survey on file is over 3 years old, a new form will be sent out for the testing facility to fill out. During a contract, the laboratory may be asked to fill out another lab survey when the original survey becomes older than 3 years.

Note: The Qualified Laboratories List (QLL) previously maintained by DPSC has been canceled.

No testing facility should refer to their previously issued QLL number.

Approval. If the testing facility and its named subcontractors meet the capability of the required testing, the DLA-PTC will notify the DLA Troop Support Product Specialist. Once approved by contracting, the testing facility becomes the Place of Performance and is placed in the contract.

Disapproval. If a testing facility does not meet the testing capability as per the specifications, the prime contractor is asked to submit another laboratory, and the process starts anew.

Note: DLA will require a total of 45 calendar days from the date of the receipt of the request to add a certified testing location to the date the requestor (contractor) is provided a decision of the laboratory certification.

Identification of Testing Sites. Unless the contract mandates a Government laboratory be used to conduct testing, the prime contractor shall identify all testing sites that will perform any test required by the terms of the contract, including end item testing.

The prime contractor shall identify a technical point of contact for the testing site and provide current contact information to DLA Contracting and the DLA Product Specialist. The prime contractor should alert the technical point of contact that the certification process has begun.

Note: DLA will require a total of 45 calendar days from the date of receipt of the request to add a certified testing location to the date the requestor (contractor) is provided a decision of the laboratory certification.

For more details on the lab certification process, see the C&T Additional Quality Assurance Requirements, which is incorporated by reference into this contract.

Marking shall be in accordance with MIL-STD-129 and Change Notice 3.

PRES/PACK TO ASTM D-3951.

EACH ROLL SHALL BE PACKED IN A

POLYETHYLENE BAG AS A MINIMUM.

PALLETIZATION IS REQUIRED FOR THESE SUPPLIES

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"ALL WOOD PACKAGING MATERIAL (WPM) ACQUIRED BY DOD MUST MEET

REQUIREMENTS OF INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES (ISPM) 15,

"GUIDELINES FOR REGULATING WOOD PACKAGING MATERIALS IN INTERNATIONAL TRADE." DOD

SHIPMENTS INSIDE AND OUTSIDE OF THE UNITED STATES MUST MEET ISPM 15 WHENEVER WPM IS

USED TO SHIP DOD CARGO, OR WHEN WOOD IS BEING ACQUIRED BY DLA FOR FUTURE USE AS

PACKAGING MATERIAL. WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAME, AND CLEATS. PACKAGING MATERIALS EXEMPT

FROM THE REQUIREMENTS ARE MATERIALS THAT HAVE UNDERGONE A MANUFACTURING PROCESS,

SUCH AS CORRUGATED FIBERBOARD, PLYWOOD, PARTICLEBOARD, VENEER, AND ORIENTED STRAND BOARD (OSD). ALL WPM SHALL COMPLY WITH ONE OF THE FOLLOWING OFFICIAL QUALITY CONTROL

PROGRAMS:

HEAT TREATMENT (HT) OR KILN DRIED HEAT TREATMENT (KD HT) IN ACCORDANCE WITH AMERICAN LUMBER STANDARD COMMITTEE, INCORPORATED (ALSC) WOOD PACKAGING MATERIAL PROGRAM AND

WPM ENFORCEMENT REGULATIONS (SEE HTTP://WWW.ALSC.ORG/; OR ALL WPM SHALL INCLUDE

CERTIFICATION/QUALITY MARKINGS IN ACCORDANCE WITH THE ALSC OR NWPCA STANDARDS, AS APPLICABLE. MARKINGS SHALL BE PLACED IN AN UNOBSTRUCTED AREA THAT WILL BE READILY VISIBLE TO INSPECTORS. PALLET MARKINGS SHALL BE APPLIED TO THE STRINGER OR BLOCK ON DIAGONALLY OPPOSITE SIDES OF THE PALLET AND BE CONTRASTING AND CLEARLY VISIBLE. ALL CONTAINERS SHALL BE MARKED ON A SIDE OTHER THAN THE TOP OR BOTTOM, CONTRASTING AND CLEARLY VISIBLE. ALL DUNNAGE USED IN CONFIGURING AND/OR SECURING THE LOAD SHALL ALSO COMPLY WITH ISPM 15

AND BE MARKED WITH AN ASLC APPROVED DUNNAGE STAMP. FAILURE TO COMPLY WITH THE

REQUIREMENTS OF THIS RESTRICTION MAY RESULT IN REFUSAL, DESTRUCTION, OR TREATMENT OF MATERIALS AT THE POINT OF ENTRY. THE AGENCY RESERVES THE RIGHT TO RECOUP FROM THE

CONTRACTOR ANY REMEDIATION COSTS INCURRED BY THE GOVERNMENT."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL

CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE

MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAYBE SHORT OR OVER THE SPECIFIED QUANTITY. SAID

CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS. IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES: 52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD

PACKAGING MATERIALS.

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS IN THE DLA TROOP SUPPORT

CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL)

SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING

CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE

LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (FEB 1999) ANSI/ISO/ASQ Q9001-2015(EXCLUDING PARA 7.3) OR EQUIVALENT.

CERTIFICATION OR REGISTRATION OF A CONTRACTOR'S QUALITY SYSTEM OR PROGRAM IS NOT

REQUIRED BY DOD IF ISO OR ANSI/ASQ STANDARDS ARE USED.

Examine Defect Marking

OMITTED, INCORRECT, ILLEGIBLE, OF IMPROPER (EXTERIOR AND SIZE, LOCATION, SEQUENCE, OR

METHOD OF INTERIOR) APPLICATION.

MATERIALS: ANY COMPONENT MISSING, DAMAGED, OR NOT AS SPECIFIED.

WORKMANSHIP: INADEQUATE APPLICATION OF COMPONENTS, SUCH AS: INCOMPLETE CLOSURE OF FLAGS, LOOSE STRAPPING, IMPROPER TAPING, INADEQUATE STAPLING, BULGED OR DISTORTED

CONTAINERS.

CONTENT NUMBER OF ITEMS PER SHIPPING CONTAINER IS MORE OR LESS THAN REQUIRED. SIZE SHOWN ON ONE OR MORE ITEMS NOT AS SPECIFIED ON SHIPPING CONTAINER. 1/1/ FOR THIS DEFECT, ONE ITEM FROM EACH SHIPPING CONTAINER IN THE SAMPLE SHALL BE EXAMINED