Tech Data PGC00490 CG BLUE 3362.pdf

TECH DATA PGC00490 8/17/2022

UNDERSHIRT, MAN'S (QUARTER SLEEVE) COAST GUARD BLUE 3362

NSN 8420016973247

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE

MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT

INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

ADDITIONAL INFORMATION FOR A-A-50013:

THE UNDERSHIRTS SHALL BE MADE IN ACCORDANCE

WITH A-A-50013G DATED SEPTEMBER 15, 2009

TYPE 1 COAST GUARD BLUE 3362, CREW NECK

STANDARD COLOR CHIP FOR COAST GUARD BLUE 3362 IS

FED STD: AMS-STD-595 COLOR CHIP 15048 FOR SHADE.

COLOR CHIPS ARE AVAILABLE FROM SAE.org.

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS (CID'S)

END ITEM DIMENSIONAL 4.0

VISUAL 2.5

SHADE EVALUATION OF CONTRACTOR FURNISHED MATERIALS:

Government Acceptance Testing. Unless otherwise stated in the contract, testing performed at the DLA PTC for acceptance purposes will be completed in forty five (45) calendar days. The contract delivery requirements are based on the assumption that DLA Troop Support and the DLA PTC will require a total of 45 calendar days from the date of the receipt of samples at the Government laboratory to the date the completed test results are mailed to the contractor.

If this time frame is exceeded, the contract delivery schedule will be extended by the number of additional days needed to complete the testing, provided the contractor can establish that the delay in its delivery was caused by the Government exceeding the prescribed time. The foregoing provision for the extension of delivery schedules is exclusive and the Government shall not be liable to suit for breach of contract by reason of any delay of the Government in providing test results.

Shade Evaluation. Shade Evaluation is Acceptance Testing; each lot must be submitted for evaluation. Lots shall not be shipped until shade is approved by Government. The prime contractor will require the fabric or component supplier to present to the source QAS the complete lot prepared for shipment, a set of tally sheets by shipment listing case numbers, roll numbers, and yardage of each roll and a shade swatch (header) from each roll with roll and case numbers identified on each swatch.

The following sampling procedure will be followed unless otherwise specified.

- SHADE SAMPLING IS APPLICABLE

- The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200)°K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)°K.

- FOR SHADE TESTING: THE COMPLETED DD FORM 1222 AND THE

SWATCHES SHALL BE FORWARDED TO:

DLA Product Testing Center Analytical 700 Robbins Avenue Philadelphia, PA 19111 ATTN: BLDG 5D Shade Room EMAIL: paactlab@dla.mil

- FOR PHYSICAL (NON-SHADE) TESTING: IN ACCORDANCE WITH CLAUSE

52.246-9032, THE CONTRACTOR'S APPROVED QUALIFIED LABORATORY WILL

BE REQUIRED TO FORWARD A COMPLETED TEST REPORT FOR EACH LOT OF

COMPONENTS TO: paactlab@dla.mil. THE QAR OR THE SUPPLIER

SOURCE SAMPLING REPRESENTATIVE, WILL FORWARD THE COMPLETED DD

FORM 1222, ALONG WITH THE SIGNED TEST REPORT. SAMPLES FOR

PHYSICAL TESTING WILL ONLY BE FORWARDED UPON REQUEST TO:

DLA Product Testing Center Analytical 700 Robbins Avenue Philadelphia, PA 19111

ATTN: BLDG 5D

EMAIL: paactlab@dla.mil

PHONE: 215-737-3246

- THE USE OF ELECTRONIC SUBMISSION OF DD FORM 1222 IS

AUTHORIZED.

SHADE EVALUATION OF CONTRACTOR FURNISHED COMPONENTS

Contracts awarded under this solicitation shall require shade evaluation of Contractor furnished components in accordance with the following provisions:

(a) Swatches shall be cut by the Contractor from those pieces or rolls selected by the Government representative. For yard goods, the dimensions of each swatch shall be 4" x 12" while for narrow loom material each swatch shall be a full width and 12" in length. The number of pieces or rolls to be sampled shall be in accordance with the following table:

Lot Size Pieces to be sampled 1 to 8 pieces Each piece 9 to 25 pieces 8 pieces 26 to 90 pieces 20 pieces 91 to 160 pieces 32 pieces over 160 pieces 1 of 5 pieces

(b) The swatches shall be submitted to the Government laboratory for shade evaluation. If any swatches are rejected, the end items made from the rejected component lot shall also be rejected. In these instances, the Contractor shall without cost to the Government, cut additional shade swatches from each remaining piece or roll in the rejected sample lot which was not previously sampled and submit these swatches to the Government for shade evaluation.

(c) Swatches submitted in accordance with (a) and (b) above, shall also be evaluated for uniformity of shade when so specified in section 3 of the fabric specification and when the standard sample is referenced for uniformity of shade.

Notification. The vendor shall notify the DLA-PTC representative via email between fourteen (14) calendar days and thirty (30) days from when lots are to be presented to the QAS. This allows arrangements to be made if the lab specialist requests to witness testing at the place of performance. The DLA-PTC will reply in writing by the date of lot presentation, whether witnessing, or side-by-samples, are requested. If no reply is received by the date of presentation to the QAS, the contractor may proceed.

Notifications should include:

Commercial lab contact information Government lot # Contract Product Specification Date of lot presentation to the QAS Certified Test Reports. Test reports shall be signed and certified by the testing facility, accompanied with a DD Form 1222 and emailed to the Government for evaluation to the following address: paactlab@dla.mil.

The test report presented to the Government shall be not older than ninety (90) calendar days. A separate report shall be provided from each test facility when a single lot of material, components, or end items is tested by more than one test facility for different characteristics.

INTERIM CHANGES TO A-A-50013G

PAGE 2, PARA 3.1 DESCRIPTION. LINE 2, AFTER COLLARETTE, ADD "SEAMLESS SIDES,".

PAGE 2, TABLE I, UNDER "BASIC MATERIAL REQUIREMENT" DELETE

"4.5 (+/-0.2)" AND SUBSTITUTE "4.0".

Page 5, paragraph 3.5 Sizes and Measurements, below the table, (A)1/2 Width. After "the measurement shall be taken across the chest" delete the remainder of the sentence and substitute "from folded edge to folded edge in accordance with figure 1 or 2."

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD

INSPECTION.

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

a. This solicitation/award consists of the following documents, exhibits, and other attachments

b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements dated October 2018, which has superseded DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, dated NOVEMBER 3, 1997.

ADDITIONAL INFORMATION FOR PPP-B-636:

FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING INTERIM FEDERAL

SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991, IS HEREBY CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM- D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD

SHIPPING CONTAINERS.

DDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL

BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS,

REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS

"PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

PACKAGING. FOUR UNDERSHIRTS OF THE SAME SIZE

SHALL BE PACKAGED WITH A CARDBOARD INSERT IN A

POLYETHYLENE BAG.

PACKING. ONE HUNDRED AND TWENTY (30 PACKAGES)

OF UNDERSHIRTS OF ONE SIZE IN A SHIPPING CARTON.

THE SHIPPING CONTAINER SHALL BE A FIBERBOARD BOX

CONFORMING TO STYLE RSC-L, TYPE CF (VARIETY SW)

OR SF, CLASS DOMESTIC, GRADE 275 OF ASTM-D1974

THE INSIDE OF EACH BOX SHALL BE FITTED WITH A

BOX LINER CONFORMING TO TYPE CF, CLASS DOMESTIC,

VARIETY DW, GRADE 275 OF ASTM-D1974. INSIDE

DIMENSIONS OF THE BOX SHALL BE APPROXIMATELY

23-1/2 INCHES IN LENGTH, 15 INCHES IN WIDTH AND

15 INCHES IN DEPTH. EACH BOX SHALL BE CLOSED

IN ACCORDANCE WITH METHOD II AS SPECIFIED IN

ASTRM-D1974. ALL SHIPPING CARTONS SHALL HAVE A

NSN AND UPC BAR CODE LABEL. MARKING OF CARTONS

AND SHIPPING LABELS SHALL BE IN ACCORDANCE WITH

MIL-HDBK-129. PALLETIZATION SHALL BE IN

ACCORDANCE WITH MIL-HDBK-774.

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129

PACKAGING SECTION. ADD THE FOLLOWING:

NOTE: UNIVERSAL PRODUCT CODE INFORMATION

THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE

(UPC) MUST BE PLACED ON AL SHIPPING CATONS ON

WHICH THE NSN APPEARS.

RFID HANGTAG:

An RFID inlay shall be added to the barcode paper hang tag attached to each item.

Where the use of self-adhesive bar-code labels are authorized, the RFID inlay may be added to the self-adhesive label in lieu of a paper hang tag. All other contract barcode and hang tag requirements still apply.

The RFID inlay should be passive Gen2 with a frequency range between 860 and 960 MHz.

The RFID antenna should be Avery/Dennis AD222 or comparable with ISO/IEC 18000-C EPCglobal C1G2 Protocol and an EPC memory allocation containing a 96 bit EPC Number.

The data linking the EPC number to the NSN, and quantity unit pack must be exportable to VIM/ASAP. The bar code of the EPC Number must be printed at the bottom of the tag along with the human readable version below the bar code.

In addition to defects applicable to the paper tag and barcoding element, the RFID tag shall be examined for the defects listed below:

RFID Inlay omitted RFID Inlay not secure RFID Inlay not laying flat when packaged RFID Inlay not readable with RFID scanner RFID Inlay or configuration not as specified

The manual "Item-Level Passive RFID Technology Manufacturer's Information Guide" provides guidance on RFID implementation and is available from the contracting officer.

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFID) Required (ref. T8379; Nov. 08, 2006)

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED

43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE

PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE

USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS

SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE

MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY.

SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006)