Tech Data - PGC 03297.docx

The blouse, woman's, service, khaki shall be made in accordance with NCTRF-PD 06-06B dated 19 June 2007.

Pattern date: 6 March 2008

Standard sample of cloth, tropical: polyester and wool, khaki shade 3729, is available and applicable for shade, physicals, colorfastness to light, laundering, perspiration (acid and alkaline), wet-dry cleaning, crocking (wet,dry),under NCTRF PD 04-06, class 2; Piece number 17102 applies.

Interim changes to NCTRF-PD 06-06B:

Page 3, paragraph 3.2.1.1.1, line 2, after "template," insert "The finished buttonhole template shall be aligned at the finished neckline using the corresponding size and length template."

Page 4, paragraph 3.2.1.6, line 3, after "body fabric" insert "shall be locked at the beginning and end of the stitch".

Page 4, paragraph 3.3.2, line 3, after "polyester)" add: "except the weight shall be a minimum 2.2 oz/yd square."

Page 4, paragraph 3.3.2, lines 3 and 4, delete "The interlinings shall be to the top ply of all components and shall be natural or approximate the color of the basic material." and substitute "The interlinings shall be to the top ply of all components and shall be khaki, white or neutral in color."

Page 4, paragraph 3.3.3, lines 2 and 3, delete: "The thread color shall be Khaki P-1, Cable no. 66019 in accordance with DoD Standard Shades for Sewing Threads." and substitute: "The thread color shall match the basic material, NCTRF PD 04-06, Class 2."

Page 4, paragraph 3.3.4, line 1, delete "and pocket flaps".

Page 5, paragraph 3.3.5.1, lines 8 and 9, delete and substitute:

"NAME___________________________________________________".

Page 6, Table I, List of Pattern Parts, delete and substitute the following:

"PIECE NAME SPEC NAME CUT # COMMENTS

Basic Material:

CENTR_FRNT Center front 2 SIDE_FRONT Side front 2 CENTR_BACK Center back 1 SIDE_BACK Side back 2 SLEEVE Sleeve 2 COLLAR Collar 2 COLLAR_STD Collarstand 2 Templates:

BHLMKR Buttonhole marker TEMPLATE V-FINTEMPL * V-Finished opening TEMPLATE Interlining:

FRTFACINT Front facing interlining 2 COLLARINT Collar interlining 1 COLSTDINT Collar stand interlining 1

*All sizes and lengths Page 6, paragraph 3.4, lines 7 and 8, delete "The Government patterns provides for a 1/4 inch seam allowance for all seams without trimming, unless otherwise specified." and substitute "The pattern provides a 5/16 inch seam allowance for safety stitched seams and a 1/4 inch seam allowance for all other seams."

Page 8, paragraph 3.6, Table II, delete and substitute:

"TABLE II - Finished dimensions for blouse A B C D E E E E E Collar 1/2 1/2 1/2 Ctr. Ctr Ctr Ctr Ctr Bust Sweep Waist Back Back Back Back Back Length Length Length Length Lgth Lgth Lgth Lgth Petite Reg. Tall X-Tall XX Tall

Size 4 12-1/2 18-1/4 19 14-3/4 22 23-1/4 24-1/2 25-3/4 27

6 12-3/4 18-3/4 19-1/2 15-1/4 22-1/8 23-3/8 24-5/8 25-7/8 27-1/8

8 13 9-1/4 20 15-3/4 22-1/4 23-1/2 24-3/4 26 27-1/4

10 13-1/4 20 20-3/4 16-1/2 22-3/8 23-5/8 24-7/8 26-1/8 27-3/8

12 13-1/2 20-3/4 21-1/2 17-1/4 22-1/2 23-3/4 25 26-1/4 27-1/2 14 13-3/4 21-1/2 22-1/4 18 22-5/8 23-7/8 25-1/8 26-3/8 27-5/8

16 14 22-1/2 23-1/4 19 22-3/4 24 25-1/4 26-1/2 27-3/4

18 14-1/4 23-1/2 24-1/4 20 22-7/8 24-1/8 25-3/8 26-5/8 27-7/8

20 14-1/2 24-1/2 25-1/4 21 23 24-1/4 25-1/2 26-3/4 28

22 14-3/4 25-1/2 26-1/4 22 23-1/8 24-3/8 25-5/8 26-7/8 28-1/8

24 15 26-1/2 27-1/4 23 23-1/4 24-1/2 25-3/4 27 28-1/4

26 15-1/4 27-1/2 28-1/4 24 23-3/8 24-5/8 25-7/8 27-1/8 28-3/8

Tol. +/- +/- +/- +/- +/- +/- +/- +/- +/- 1/4 3/8 1/2 1/2 1/4 1/4 1/4 1/4 1/4

F Sleeve Length 1/

Petite 3-1/8 Regular 3-5/8 Tall 4-1/8 X-Tall 4-1/8 XX-Tall 4-5/8

Tolerance +/-1/4 Page 12, paragraph 4.4.3, Table VII, add new "Appearance" defect: "d.11. Blindstitching on blouse not locked at beginning and end of stitch." Defect point value is "3".

Page 18, delete "Figure 3" and substitute revised "Figure 3" NEXCOM LABELING ONLY: Each shirt/blouse shall have a non-curl label approximately 1-1/2" X 1-1/2" sewn inside at neck. "Classic" or "Athletic" shall be clearly identified in 12pt. font (include bust measurement on female over blouse), a UPC stick-on label approximately 2" X 2-1/2", and placed on the right front bottom of the bag including NSN and size as specified.

RECRUIT TRAINING CENTER (RTC) - Each shirt/blouse shall also be packed in a plastic bag. Heat sealing of the bag is prohibited.

Refer to the packaging data for specific information relating to this item.

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

COMMERCIAL

V-B-871F Button, Sewing Hole, and Button, Staple, (plastic) has been canceled and is superseded by A-A-59994 Button, Sewing Hole, and Button, Staple, (Plastic) dated 04 Dec 2018

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR MIL-STD-1492C:

MIL-STD-1492C, PAGES 7-8, TABLE II, DELETE IN

ITS ENTIRETY AND SUBSTITUTE: "TABLE II

SAMPLING PROVISIONS FOR END ITEM VISUAL

EXAMINATION OF SEMI-DRESS (SD) SHIRTS

NORMAL INSPECTION

LOT SZ SAMP SZ MAX ACCP PT VALUES

. 3&2 PT 3,2,1 PT

. DEFECTS DEFECTS

UP THRU 500 50 5 10

501-1200 80 7 14 1201-3200 125 10 20 3201-10,000 200 14 29 10,001-35,000 315 20 42

35,001 & OVER 500 30 62

TIGHTENED INSPECTION

UP THRU 500 50 3 7

501-1200 80 5 11 1201-3200 125 7 15 3201-10,000 200 11 23 10,001-35,000 315 17 34

35,001 & 0VER 500 25 52

REDUCED INSPECTION

LOT SZ SAMP SZ MAX ACCP PT VALUES

. 3&2 PT 3,2,1 PT

. DFCTS 1/ DEFECTS

UP THRU 1200 32 3-7 11

1201-3200 50 5-9 14 3201-10,000 80 7-11 19 10,001-35,000 125 10-14 24

35,001 & OVER 200 14-18 34

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE."

CLOTH, TROPICAL: POLYESTER AND WOOL, CLASS 1 and 2

ADDITIONAL INFORMATION FOR NTCRF PD 04-06, CLASS 1:

STANDARD SAMPLE FOR CLOTH, TROPICAL: POLYESTER AND WOOL, BLUE 3346 CONFORMING TO NCTRF PD 04-06, IS AVAILABLE ON ROLL NO. 10163, AND APPLICABLE FOR SHADE, FINISH AND COLORFASTNESS.

ADDITIONAL INFORMATION FOR NTCRF PD 04-06, CLASS 2:

STANDARD SAMPLE FOR CLOTH, TROPICAL: POLYESTER AND WOOL, KHAKI 3729 CONFORMING TO NCTRF PD 04-06, IS AVAILABLE ON ROLL NO. 06081, AND APPLICABLE FOR SHADE, FINISH AND COLORFASTNESS.

RECOMMEND 100 PERCENT SHADE VERIFICATION FOR EACH LOT PRESENTED TO GOVERNMENT FOR LIFE OF THE ITEM.

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS.

PART I AND II, JULY 2000 AND SUPPLEMENT, MARCH 2000

Examination of packaging requirements. An examination shall be made to determine that packaging, packing, and marking comply with MIL-STD-129, MIL-STD-2073-1D, ASTM D5118, and ASTM D1974. Defects shall be scored in accordance with the list below. The sample unit shall be one shipping container fully prepared for delivery. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 and the acceptable quality level (AQL) shall be 2.5, expressed in term of defects per hundred units.

Examine Defect

Marking Omitted,incorrect,illegible,of improper (Exterior and size, location,sequence, or method of interior) application.

Materials Any component missing, damaged, or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of flags, loose strapping, imprper taping, inadequate stapling, bulged or distorted containers.

Content Number of items per shipping container is more or less than required. Size shown on one or more items not as specified on shipping container. 1/

1/ For this defect, one item from each shipping container in the sample shall be examined..

NEXCOM LABELING ONLY: Each shirt/blouse shall have a non-curl label approximately 1-1/2" X 1-1/2" sewn inside at neck. "Classic" or "Athletic" shall be clearly identified in 12pt. font (include bust measurement on female over blouse), a UPC stick-on label approximately 2" X 2-1/2", and placed on the right front bottom of the bag including NSN and size as specified.

RECRUIT TRAINING CENTER (RTC) - Each shirt/blouse shall also be packed in a plastic bag. Heat sealing of the bag is prohibited.

Refer to the packaging data for specific information relating to this item.

PACKAGING

Marking shall be in accordance with MIL-STD-129 and change notice 3.

Thirty (030) shirts shall be packed in a fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC, Grade 275, variety SW, Class domestic, with a double wall liner. Any commercial closure method cited in ASTM-D-1974 is acceptable except stapling. The shirts/blouses shall be individually packaged in a plastic bag approximately 10" X 15" with one piece of cardboard backing to include collar tab. Do not heat seal the bag.

NEXCOM PACKAGING ONLY: Thirty-six (036) shirts/blouses shall be packed in a fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC, Grade 275, Variety SW, class domestic, with a double wall liner. Any commercial closure method cited in ASTM-D-1974 is acceptable except stapling. The shirts/blouses shall be individually packaged in a plastic bag approximately 10" X 15" with one piece of cardboard backing to include collar tab. Do not heat seal the bag.

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006)