Tech data-MC Run Jkt- PGC03410R.pdf

TECH data PGC03410 5/15/23

NSN 8415015501251

US MARINE CORPS RUNNING SUIT - JACKET

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY

REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT

IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON

THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

THE FULLY LINED JACKET SHALL BE MADE IN ACCORDANCE WITH FQ/PD-08-05A

DATED 25 FEBRUARY,2015. PATTERN DATE: 30 JULY 2015

STANDARD SAMPLE FOR BASIC MATERIAL,

ROLL# 3778 IS APPLICABLE FOR SHADE AND APPEARANCE.

INTERIM CHANGES TO FQ/PD 08-05A

Document Title – delete “Marine Corps Running Suit – Jacket and replace with “Jacket, Running Suit”

Delete 1. SCOPE and 2. CLASSIFICATION in its entirety and replace with the following:

“1. SCOPE

1.1 Scope. This purchase description covers the requirements for the physical fitness athletic jacket (running suit). The jacket is intended for wear by personnel of the U.S. Marine Corps and U.S. Navy.

1.2 Classification. The jackets will be available in types, classes and sizes.

1.2.1 Types. The jackets shall be available in the following types.

Type I – Heat transfer, U.S. Marine Corps Type II – Heat transfer, U.S. Navy

1.2.2 Classes. The jackets shall be available in the following classes.

Class 1 - Belleau Wood Green 523 (U.S. Marine Corps) Class 2 - Blue 3393 (U.S. Navy)

1.2. Sizes. The jackets shall be available in the following sizes:

X-Short Short Regular Long X-long XX-Small XX-Small ---- ---- ---- X-Small X-Small ---- ---- ----

Small Small Small Small ---- Medium Medium Medium Medium Medium

---- Large Large Large Large ---- ---- X-Large X-Large X-Large ---- ---- XX-Large XX-Large XX-Large”

3.1 Description, Delete last sentence and replace with “ The Type I shall have silver non-reflective heat transfer of the Marine Corps Eagle, Globe, and Anchor symbol (EGA), and the text “MARINES” (see figure 2). The Type II shall have the text “NAVY” applied as a non-reflective heat transfer in gold Pantone 1225U in accordance with the style and dimensions in Figure 1. See 3.1.2 for placements.”

“ 3.1.2 Non-reflective heat transfers.

3.1.2.2, Non-reflective heat transfer (Type I). The non-reflective heat transfer markings for the Marine Corps Eagle, Globe, and Anchor (EGA) symbol shall be placed on the left upper chest panel and the “MARINES” logo placed across the center back yoke in accordance with the placement markings on the patterns. The EGA shall consist of silver (non-reflective) heat transfers. The “MARINES” logo shall match scarlet (SRI 484 CC) and gold (SRI 143) Pantone colors. The logo shall be solid scarlet lettering with a gold outline using the Marine Corps custom Hercules font. Finished dimensions of the EGA logo and MARINE text are as follows.

See figure 2.

Dimensions and Tolerances, inches Left upper chest panel

EGA

Center back yoke

“MARINES”

Height 3-1/2 (± 1/8) 1-3/8 (± 1/8)

Width 3-1/8 (± 1/8) XX-Small, X-Small, Small & Medium: 13-1/8 (± 1/4)

Large, X-Large & XX-Large:

15 (± 1/4)

PAGE 2 – Continued

3.1.2.3 Non-reflective heat transfer (Type II). The non-reflective heat transfer markings of the “NAVY” logos shall be placed on the left upper chest panel and placed across the center back yoke in accordance with the placement markings on the patterns. The logos shall match gold (1225U) Pantone. Finished dimensions of the NAVY logo are as follows. See figures 3 and 4.

Dimensions and Tolerances, inches Left upper chest panel

“NAVY”

Center back yoke

“NAVY “

Height 1-1/2 (± 1/8) 3-1/8 (± 1/8)

Width 4-3/4 (± 1/8) 10-1/4 (± 1/4)”

Delete 3.2.2 Reflectivity in its entirety and replace with the following:

“3.2.2 Reflective Material. All reflective marking material used shall be visible for a distance of at least 100 yards in pre-dawn, dusk, and night conditions when placed within an area of 45 degrees on either side of the centerline of vehicle headlamps on low beams. Reflective protection shall be 360o around the individual wearing the jacket.

The reflective material for the reflective piping, tape, and zipper shall be tested in accordance to the ANSI/ ISEA 107 American National Standard forHigh-Visibility Safety Apparel and Headwear and certified for the level 2 category. When tested in accordance with AATCC TM135 (3) III Aiii for 50 cycles the reflective findings shall maintain a minimum reflectivity brightness of 100 cd/lux/m2 at

0.2 degree observation angle and entrance angle of 5 degrees and shall not delaminate, crack, craze, peel, exhibit color change or otherwise become unserviceable. Additionally, when tested in accordance with AATCC TM135 (1) IV Ai for 5 cycles the reflective findings shall maintain a minimum reflectivity brightness of 100 cd/lux/m2 at 0.2 degree observation angle and entrance angle of 5 degrees and shall not delaminate, crack, craze, peel, or otherwise become unserviceable. A certificate of conformance is acceptable for this requirement.”

Delete 3.4.1 Basic material in its entirety and replace with “3.4.1 Basic material. The 100% Nylon material shall be Perseus with nanosphere, Marathon or equal (see 7.4). The color for Class 1 shall be Belleau Wood Green shade 523. The color for Class 2 shall be Blue 3392. The exterior material shall conform to the requirements in TABLE I.”

3.4.6 Waist bungee cord, delete line 2 in its entirety and replace with the following:

“The cut lengths shall be as follows:

Size XXS XS S M L XL XXL Tol Cut Length (inches) 65 68 71 74 77 80 83 ± 1/2”

Delete 3.4.8 Slide fasteners & 3.4.8.1 Center Front Zipper in its entirety and replace with “3.4.8 Slide fasteners. The slide fasteners for center front, side and right hidden pockets shall conform to the specified type of A-A-55634 in Table IV. The chain, slider and pull shall be black. The pocket zippers shall be black tape. The center front slide fastener shall be a pre-assembled individual element, injection molded plastic separating fastener with single automatic locking enamel finish slider, left hand insertion, with 9/16 or 5/8 inch wide black tape with 1/4-inch laminated silver reflective tape adhered 1/16-inch from the edge of the chain. The reflective film must be attached to the slide fastener tape before the assembly process and be visible along the entire length of the slide fastener. Top and bottom reinforcement tapes must be clear or translucent film. See suggested source for center front slide fastener.”

Table V, Cut Length of Elastic (in inches) add “XX-Large” for size and add “5 “for length.

Delete the templates in Table VI. Pattern Parts List and replace with the following “

“Table VI. Pattern Parts List

Pattern Nomenclature Computer Nomenclature Cut Parts Templates Back Yoke Logo Template Type I Only PD0805-BK_YK_TM_I 0 Back Yoke Logo Template Type II Only PD0805-BK_YK_TM_II 0 Left Front EGA Template Type I Only PD0805-LFT_FRT_TM_I 0 Left Front Logo Template Type II Only PD0805-LFT_FRT_TM_II 0 Back Reflective Tape Template Type I and II PD0805-BK_RFLCT_TAPE 0”

PAGE 8 - Continued

Delete 3.6.2 Finished measurements in its entirety and replace with the following: “3.6.2 Finished Measurements. The Type I and Type II jackets shall conform to the finished measurements listed below (see figure 1).”

Jacket finished measurements (inches)

XX-Small X-Small Small Medium Large X-Large XX-Large Tol.

Half Chest 1/ 19-1/2 21 22-1/2 24 25-1/2 27 28-1/2 +3/8 Half Sweep 2/ 19 20-1/2 22 23-1/2 25 26-1/2 28 +3/8 Half Sleeve Opening 3/

3-1/2 3-1/2 3-1/2 3-1/2 4 4 4-1/2 +1/4

Collar Length 4/ 17-1/4 18 18-3/4 19-1/2 20-1/4 21 21-3/4 +1/4

Back Length 5/ +1/2 X-Short 24-1/2 24-1/2 25-1/2 25-1/2 ---- ---- ---- Short 26-1/2 26-1/2 27-1/2 27-1/2 28-1/2 ---- ---- Regular ---- ---- 29-1/2 29-1/2 30-1/2 30-1/2 31 Long ---- ---- 31-1/2 31-1/2 32-1/2 32-1/2 32-1/2 X-Long ---- ---- ---- 33 34 34 35

Front Length – Slide Fastener 6/

+1/2

X-Short 22-1/2 22-1/2 23-1/2 23-1/2 ---- ---- ---- Short 24-1/2 24-1/2 25-1/2 25-1/2 26-1/2 ---- ---- Regular ---- ---- 27-1/2 27-1/2 28-1/2 28-1/2 29-1/2 Long ---- ---- 29-1/2 29-1/2 30-1/2 30-1/2 31-1/2 X-Long ---- ---- ---- 31 32 32 33

Sleeve Length 7/ +1/2 X-Short 19-1/2 19-1/2 19-1/2 19-1/2 ---- ---- ---- Short 21 21 21 21 21 ---- Regular ---- ---- 22 22 22 22 22 Long ---- ---- 23 23 23 23 23 X-Long ---- ---- 24-1/2 24-1/2 24-1/2 24-1/2

PAGE 8 – Continued

1/ Half Chest – Measure from folded edge to folded edge across base of armhole.

2/ Half Sweep – Measure from folded edge to folded edge straight across bottom of jacket.

3/ Half Sleeve Opening – Measure from folded edge to folded edge with sleeve cuff flat and elastic relaxed.

4/ Collar Length – With jacket open measure from intersection of facing edge and collar seam along neck seam to opposite collar edge.

5/ Back Length – With jacket laying front down, measure from collar seam at center to bottom edge.

6/ Front Length Slide Fastener – Measure from top of slide fastener to bottom of slide fastener 7/ Sleeve Length – Measure from base of armhole seam to bottom edge of sleeve.

Table VII Construction Details, add the following row to the end of the table and insert the following:

“Center front slide fastener Reflective tape 1/8 (+1/32) inch exposed when finished.”

TABLE VIII: Visual Inspection. Add the following sentence to line 5, “Draw-cord, “Any drawcord not bar-tacked at center back.”.

Table VIII, Visual inspection, delete row 10, Markings in its entirety and replace with the following:

“Non-reflective heat transfer markings Type I: Marine Corps Eagle, Globe and Anchor (EGA) emblems or “MARINES” logo missing or illegible, not in accordance to the pattern location or font, exceeding dimensional tolerances or not clearly identifiable.

Type II: “NAVY” logos missing or illegible, not in accordance to the pattern location, exceeding dimensional tolerances, not in correct style or not clearly identifiable.

Type I and II: Heat transfer color not as specified, consistent, peeling, cracking, incomplete, lettering edges not clearly defined or not aligned parallel to bottom of yoke.”

Table VIII, Visual inspections, Delete row 12, Heat transfers in its entirety.

Table VIII Visual inspections, Row 2, defect column, line 1 delete “Jacket not Belleau Wood Green,”

7.4 Suggested Sources add “Brookwood Companies Inc.” to the basic material suggested sources as follows:

“Brookwood Companies, Inc Company Headquarters 25 W 45th St, 11th Floor New York, NY 10036 P 212-551-0100 info@brookwoodcos.com”

Add “Figure 1. Points of Measurement for Type I and Type II” under figure.

Add “Figure 2. Type I, - U.S. Marine Corps, Front and Back”under the figure.

mailto:info@brookwoodcos.com

Page 7, 3.3.7 Draw-cord. Delete line 4 in entirety and replace with the following:

Size XXS XS S M L XL XXL Tol Cut Length (inches) 65 68 71 74 77 80 83 ± 1/2”

AQLS SHALL BE AS FOLLOWS:

END ITEM DIMENSIONAL 4.0 - INSPECTION LEVEL S-3

VISUAL 6.5 - INSPECTION LEVEL II

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF "SAMPLING PROCEDURES AND TABLES FOR

INSPECTION BY ATTRIBUTES", ANSI/ASQC Z1.4.

EACH JACKET SHALL BE NEATLY FOLDED AND INSERTED

IN A CLOSE FITTING CLEAR POLYETHYLENE BAG.

24 JACKETS OF ONE SIZE ONLY SHALL BE PACKED

IN A SNUG FITTING FIBERBOARD SHIPPING CONTAINER

CONFORMING TO ASTM-D5118, TYPE CF, STYLE RSC-L

(LINER), GRADE 275, VARIETY SW, CLASS DOMESTIC

APPROXIMATE BOX DIMENSIONS ARE FURNISHED AS A

GUIDE ONLY: LENGTH 23-1/2 INCHES, WIDTH 15

INCHES, AND DEPTH 15 INCHES.

THE FOLLOWING REQUIREMENTS ARE IN ACCORDANCE

WITH ASTM-D1974 METHODS OF CLOSING, SEALING AND

REINFORCING FIBERBOARD BOXES. CLOSURE METHODS

SHALL BE 2A2, FIGURE 1, OR AS AN ALTERNATE,

2B6 OR 2B7, FIGURE 3.

AQLS SHALL BE AS FOLLOWS:

END ITEM DIMENSIONAL: 4.0 - INSPECTION LEVEL S-3

VISUAL 6.5 - INSPECTION LEVEL II

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF "SAMPLING PROCEDURES AND TABLES FOR

INSPECTION BY ATTRIBUTES", ANSI/ASQC Z1.4

DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS

AND STANDARDS, PART I AND II, JULY 1993 AND

SUPPLEMENT, MARCH 1994

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE

FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG

FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE

STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A

SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS

SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER,

CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT

SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT

UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT.

THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN

AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT

THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED

AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED

UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON

WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE

SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE

VIII (TAG, PAPER) OF MIL-DTL-32075.

THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED

ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS".

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE

MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES

THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS

OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS

OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER

TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PRES/PACK SHALL BE IAW ASTM D 3951, COMMERCIAL

SHIPPING CONTAINER = 24.

Packaging examination. The fully packaged end item shall be examined for the defects listed below.

The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Examine Defect

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, sequence or method of appli-cation.

RFID HANGTAG:

An RFID inlay shall be added to the barcode paper hang tag attached to each item. Where the use of self-adhesive bar-code labels are authorized, the RFID inlay may be added to the self-adhesive label in lieu of a paper hang tag. All other contract barcode and hang tag requirements still apply.

The RFID inlay should be passive Gen2 with a frequency range between 860 and 960 MHz. The RFID antenna should be Avery/Dennis AD222 or comparable with ISO/IEC 18000-C EPCglobal C1G2 Protocol and an EPC memory allocation containing a 96 bit EPC Number. The data linking the EPC number to the NSN and quantity unit pack must be exportable to VIM/ASAP. The bar code of the EPC Number must be printed at the bottom of the tag along with the human readable version below the bar code.

In addition to defects applicable to the paper tag and barcoding element, the RFID tag shall be examined for the defects listed below:

RFID Inlay omitted RFID Inlay not secure RFID Inlay not laying flat when packaged RFID Inlay not readable with RFID scanner RFID Inlay or configuration not as specified

The manual "Item-Level Passive RFID Technology Manufacturer's Information Guide" provides guidance on RFID implementation and is available from the contracting officer.

Pallet, Case & Item level RFID is required for the Clothing & Textiles Directorate (C&T) for Bag items only.

(ref. ZT046 ; Aug 2021)

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING

MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible.

All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS

SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN

HEIGHT (INCLUDING THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL

BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO

PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF

CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT

POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO

LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE

THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN

MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE

CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO

APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS

(WPM) - (JULY 2006)

52.246-2, Inspection of Supplies - Firm-Fixed Price 52.209-4, Alt. I, First Article Approval - Government Testing

52.246-15 CERTIFICATE OF CONFORMANCE

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

a. This solicitation/award consists of the following documents, exhibits, and other attachments

b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements Revision 1 dated August 2021, which has superseded DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018.

INSPECTION AT SOURCE/ACCEPTANCE AT SOURCE

CLAUSE 52.246-9032 IDENTIFICATION OF QUALIFIED LABORATORY AND SOURCE

SAMPLING APPLIES.

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFID) Required (ref. T8379; Nov. 08, 2006)