TECH DATA DEVIATIONS TO A-A-55239A.pdf
PDF 60 KB Posted
- Attached to
- Marine Corps Sweaters Federal contract opportunity
- Solicitation number
- SPE1C1-24-R-0002
About this file
This document outlines technical data deviations to military specification A-A-55239A for Marine Corps sweaters. The deviations specify changes to tolerance limits for skirt width and addition of epaulettes with hook and loop fasteners on the shoulders. The epaulettes will be made of two plies of fabric from shoulder and elbow patches, tapered and finished with hook or loop fastener to attach to the sweater. Sweater weights in pounds are provided by size ranging from 11-1/4 to 21-1/2 pounds. The related federal contract opportunity is a pre-solicitation for Marine Corps sweaters under solicitation SPE1C1-24-R-0002 from the Defense Logistics Agency Troop Support Clothing and Textiles.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| Specification CID A-A-55239A - 01 Nov 1996.pdf | ||
| PGC 02765 UPC Code.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
TECH DATA DEVIATIONS TO A-A-55239A:
PARAGRAPH 3.7, TABLE III. FINISHED MEASUREMENTS. FOR THE COLUMN TITLED
SKIRT WIDTH", UNDER TOLERANCE DELETE "PLUS OR MINUS 1/2" AND SUBSTITUTE
"PLUS OR MINUS 1".
THE FOLLOWING NEW PARAGRAPHS SHALL BE ADDED:
EPAULETTES. THE EPAULETTES SHALL FINISH SMOOTH AND FLAT AND BE UNIFORM IN
CONSTRUCTION AND PLACEMENT. THE EPAULETTES SHALL BE MADE FROM TWO PLIES OF
THE SAME FABRIC USED FOR THE SHOULDER AND ELBOW PATCHES AND SHALL BE SEWN
TOGETHER WITH EDGES TURNED IN BY LOCKSTITCHING (STITCH TYPE 301)
WITH AT LEAST 10 STITCHES PER INCH OF SEAM AND SHALL FINISH 2 INCHES WIDE AT
THE ARMHOLE SEAM TAPERING TO 1-3/4 INCHES WIDE AT THE ROUNDED END. PRIOR TO
STITCHING THE TWO PLIES OF THE EPAULETTE, A PATCH OF LOOP PILE FABRIC
3/4 INCH LONG IS TO BE SEWN 1/4 - 3/8 INCH (CENTERED) FROM THE ROUNDED END OF
THE UNDERPLY OF EPAULETTE. POSITION THE EPAULETTE SO AS THE ROUND END OF LOOP
IS 3/8 INCH BEYOND THE COLLAR SEAM WITH THE BACK FINISHED EDGE OF THE
EPAULETTE ON THE FINISHED SWEATER (SWEATER IN RELAXED STATE) SHALL BE 1/2
INCH BEHIND THE SHOULDER SEAM. THE EPAULETTE IS INSERTED INTO THE SLEEVE
SETTING SEAM. THE HOOK TAPE SHALL BE MOVED TO MATCH THE LOOP PILE ON THE
EPAULETTE. FOR SWEATER SIZES 28 THROUGH 32, THE LOOP PILE FABRIC PIECE MAY
BE 1/2 TO 1/2 SQUARE AND SHALL BE STITCHED AS CLOSE TO THE END OF THE
EPAULETTE AS POSSIBLE. ON THE UNDERSIDE OF EPAULETTE, THE INNER EDGE
OF LOOP PILE FABRIC TO SLEEVE SETTING SHALL MEASURE A MINIMUM OF 3-5/8
INCHES. A 3/4 INCH LONG PIECE OF HOOK FABRIC IS TO BE SEWN ON THE SHOULDER
PATCH ABUTTING THE EDGE OF THE NECKBAND IN ALIGNMENT WITH THE LOOP FABRIC
ON THE UNDERSIDE OF THE EPAULETTE ADHERING TO CLEARANCE MEASUREMENT AS
DESCRIBED ABOVE. THE EPAULETTE SHALL LIE SMOOTH AND FLAT OVER SHOULDER PATCH
WHEN THE LOOP AND PILE FABRICS ARE ENGAGED. NO FUSIBLE IS REQUIRED.
HOOK AND LOOP. THE HOOK AND LOOP FOR ALL THE SWEATER SIZES SHALL BE 5/8 INCH
WIDE BY 3/4 INCH LONG, TYPE I, CLASS 1, NYLON, IN ACCORDANCE WITH A-A-55126.
THE SHADE OF THE HOOK AND LOOP SHALL APPROXIMATE THE SHADE OF THE EPAULETTE
FABRIC.
SWEATER (WITH EPAULETTES) WEIGHTS. THE WEIGHTS PER SIZE (EXPRESSED IN POUNDS)
AND BASED ON 12 SWEATERS SHALL BE AS FOLLOWS:
28/30 11-1/4 32/34 13 36 14-1/2 38 15-1/4 40 17-3/8 42 18-1/8 44 19-1/4 46 20 48 20-3/4 50 21-1/2
THE TOLERANCE ON THE WEIGHT FOR THE SWEATER (WITH EPAULETTES) IS PLUS OR
MINUS 1/4 POUND.
ADD THE NEW FIGURE TO BACK OF DOCUMENT FIGURE 3. SWEATER, SERVICE, WOOL,
EPAULETTES
(Ref. W2765)
File details come from the government source that posted it. Updated .