The file's text, extracted by GovTribe without its formatting.
TE24004 Flatbed with Knuckle boom crane Specification Requirements
0821 FLATBED WITH KNUCKLE BOOM CRANE
Specification Requirements
Be sure to address each line below. Failure to do so may result in bid rejection Check
If Meet or Exceed Describe Offered Alternatives
Note: Equals or Alternatives offered may be evaluated by subject matter experts. Equals or Alternatives offered that are not found to meet the specification requirements may cause the bid to be rejected.
| 1. |
| This specification is intended as a general indication of the type of equipment desired. Because of the variation in types of equipment available, other configurations may be evaluated and WSDOT reserves the right to reject any and all bids which do not meet the intent of the specifications in the judgment of the Department. Bidders shall furnish complete specifications of the unit bid, including make and model numbers as well as all other pertinent data to facilitate evaluation for compliance with the intent of the specifications. See the Specification Evaluation section of the RFQ. |
| 2. |
| The unit bid shall be a current model year, complete “turn key” unit including chassis, flatbed and crane |
| 3. |
| Supplier shall be capable of providing an axle load, stability and weight distribution analysis for the specified carrier vehicle. |
| 4. |
| The vendor shall determine the proper wheelbase and cab to axle measurements required for use with the specified flatbed and aft of rear axle EOF mounted crane. |
Note: WSDOT desires the rear axle to be as far forward as possible while still meeting weight distribution and stability requirements Note: WSDOT estimates up to 8,000 pounds of payload on the flatbed deck beyond the as equipped tare weight.
| 5. |
| At the time of order placement, the Vendor and WSDOT will schedule a meeting to review/clarify the technical specifications specific to each order. |
| 1. |
| Chassis shall have a GVWR of 41,000 lbs |
| 2. |
| Shall have a 67 MPH road speed and cruise control limit |
| 3. |
| Shall have sufficient frame after the end of the flatbed to allow for an EOF mounted crane |
| 1. |
| Shall be a conventional day cab |
| 2. |
| Shall be heated and air conditioned |
| 4. |
| Shall have heated and power adjustable mirrors including an additional convex spot mirror |
| 5. |
| Shall have a positive load disconnect with cab mounted control switch mounted outboard driver seat |
| 6. |
| Shall be equipped with the following gauges |
a) Voltmeter
b) Engine oil pressure
c) Tachometer
d) Hour meter
e) Coolant temp
f) Outside air temp
| 7. |
| Shall be equipped with an air Horn |
| 8. |
| Shall be equipped with electric, intermittent windshield wipers and electric door locks |
| 9. |
| Shall be equipped with both interior and exterior egress / ingress assist handles on the driver’s side and interior grab handles on the passenger side. |
| 10. |
| Shall be equipped with an AM/FM radio with Bluetooth connection and speakers. |
| 11. |
| Shall have adjustable steering column / steering wheel. |
| 12. |
| Driver and passenger seat shall be cloth covered high back air ride seats with lumbar support and arm rest. |
| 13. |
| Shall have "pre-trip inspection" light test button |
| 2. |
| Shall have a capacity between 50 – 80 gallons |
| 3. |
| Shall be left side mounted |
| V. |
| Electrical system, accessories, and lighting - Supplier splices into the factory wiring harness is unacceptable |
| 2. |
| All chassis lighting to include marker lights, clearance lights, backup lights, taillights, stop lights and turn signals shall be LED with the exception of the headlights. |
| 3. |
| Shall be equipped with halogen headlights. |
| 4. |
| Shall be equipped with a variable sound backup alarm |
| 5. |
| Batteries shall be a minimum of 2850 CCA |
| 6. |
| The batteries shall be equipped with a ground cable which will be attached to the frame rail. All cable ends shall be sealed and equipped with rubber retainers and covers. |
| 7. |
| Shall have OEM in dash, 6 switch panel for accessory lighting powered by the ignition switch in both run and accessory positions. |
| 8. |
| Shall have a horn alarm that sounds when the vehicle parking brake is not set and the driver's door is opened. |
| 1. |
| Michelin X line energy Z 315/80R22.5 20 Ply radial front tires |
| 2. |
| Michelin XDN2 11R22.5 14 Ply radial rear tires |
| 3. |
| Equipped with Accuride steel disc front and rear wheels |
| 1. |
| Shall have a 18k driven leaf spring front axle (4x4) |
| 2. |
| Shall have a 23k leaf spring rear drive axle |
| 3. |
| Ratios shall allow for the truck to achieve a highway speed of 67 MPH. |
| 4. |
| Equipped with Meritor S cam brakes front and rear |
| 5. |
| Rear axle shall have an air locking differential |
| 1. |
| Front brakes shall be S-cam drum and properly sized for the truck's GVWR |
| 2. |
| Rear brakes shall be S-cam drum and properly sized for the truck's GVWR |
| 3. |
| All Brake linings shall be non-asbestos |
| 4. |
| The air dryer, shall be mounted in a serviceable location and the filter will be a spin on style. |
| 5. |
| Air tanks shall be equipped with a lanyard style drain that is accessible by the driver. |
| 6. |
| Shall be equipped with a tractor protection valve. |
| 7. |
| Shall be equipped with a trailer brake hand control valve. |
| 1. |
| Shall have a Cummins L9 rated at 350 HP @ 2200 RPM with 1050 Lb-Ft @ 1200 RPM |
| 2. |
| Shall be equipped with and OEM 110 VAC block heater, with the receptacle located on the left side under the driver’s door. |
| 3. |
| Maximum road speed governed at 65 mph. |
| 4. |
| Shall be equipped with an engine brake. |
| 5. |
| Shall be dual element, with fresh air intake. |
| 6. |
| Shall be equipped with an air filter assembly restriction gauge. |
| 1. |
| Shall be a single horizontal muffler and vertical pipe. The vertical pipe shall not protrude more than 3 - 5 inches behind the cab. |
| 2. |
| Shall have an under cab mounted horizontal DPF and DOC |
| 3. |
| The end of the exhaust pipe shall have a 45-degree tip out, positioned so that it will not interfere with the cab, cab guard or lights |
| 1. |
| Shall be equipped with an Allison 3000 RDS transmission with PTO provision and dash mounted push button shift control |
| 2. |
| Equipped with a two-speed transfer case, with dash mounted shift controls |
| 1. |
| The bed shall be equipped with an expanded metal cab shield extending to the height of the cab roof and with sufficient frame structure to protect the cab |
| 2. |
| All wood for the decking shall be Iron Wood |
| 3. |
| Bed dimensions shall be 18’ long x 8’6” wide. |
| 4. |
| Bed shall be equipped with Stake pockets every 2 feet. |
| 5. |
| Shall be equipped with a rub rail connecting the stake pockets |
| 6. |
| Bed shall have a slide in ladder access, located on both the right and left front side of the flatbed. |
| XIII. |
| FLAT BED COMPONENTS: |
| 1. |
| Shall be equipped with two weatherproof 40 X 20 X 27 lockable, storage boxes mounted below the deck of the flatbed on each side of the flatbed mounted forward of the rear axle. |
| 2. |
| The boxes shall have one fold down door with “D” ring twist latches and keyed alike. |
| 1. |
| The chassis shall be equipped with a hitch plate and pintle hitch to accommodate towing 50,000 pounds. |
| 2. |
| Shall be equipped with trailer towing provisions at EOF including air connections with glad hands and 7 way trailer receptacle |
| 1. |
| Crane Shall be a Palfinger PK26002-EH “B” four boom configuration or equal |
| 2. |
| The crane shall be mounted aft of rear axle at end of frame. |
| 3. |
| The horizontal hydraulic reach of the crane shall be at least 33’. |
| 4. |
| The crane shall have the ability to lift at least 5000 pounds at 33 feet. |
| 5. |
| Shall have continuous rotation. |
| 6. |
| The crane shall be equipped with an electronic overload protection system, with display. The display will be located at both control stations and will display specifically where the overload condition is taking place. The system will disable all load-increasing functions. This overload system shall not allow the boom to drift or lower the load. |
| 7. |
| The crane shall be equipped with a mechanical linkage that connects the folding boom cylinder to the folding and extension booms. |
| 8. |
| The crane’s folding boom shall have an operating radius of 180 degrees under rated load. |
| 9. |
| The crane’s folding boom tip speed shall be constant throughout its 180 degree operating radius without requiring the operator to meter the control valve. |
| 10. |
| The crane shall have individual sequentially extending cylinders, which will result in a constant capacity and constant speed. Telescopic extension cylinders are unacceptable. |
| 1. |
| Outrigger spread shall be not greater than 24.5 feet. |
| 2. |
| Outrigger beam shall be hydraulically extendible both laterally and vertically |
| 3. |
| The outrigger legs shall also have the ability to rotate at least 90 degrees. This will enable the outriggers to extend over the top of a mobile barrier or guardrail. |
| 1. |
| The control valve shall be equipped with both a main and port relief valve to protect the pump cylinder and hoses. |
| 2. |
| The control valve shall have precise metering capability and the operator shall be capable of operating two crane functions simultaneously. |
| 3. |
| Shall be equipped with load holding valves on the main, folding, and extension boom cylinders and the outrigger jacks |
| 4. |
| Shall be equipped with a cab controlled Hot Shift PTO. |
| 5. |
| The cab shall be equipped with a PTO engage light located on the switch panel. |
| 6. |
| The entire hydraulic system shall be sized to operate at full capacity and without overheating. |
| 7. |
| Shall be equipped with an oil level sight indicator, return filter cartridge, clean out port, temperature gauge, hydraulic system shut off valves and installed as per manufacturers requirements. |
| 8. |
| The crane shall be equipped with two (2) sets of controls. The controls for the boom shall be located in a manner to operate all boom functions at ground level and from both the left and right side of the crane. |
| 1. |
| Shall be equipped with, on top of the chassis cab, 2 (two) current WSDOT specified Whelen Responder LP Super-LED mini light bars, part number R2LPHPA. |
| 2. |
| Shall be equipped with 2 (two) Fire Research Spectra MS 12VDC Scene lights Model number SPA540-R14-TW (or equal) side mounted extendible floodlights. One light shall be mounted on each front corner of the body. |
| 3. |
| The flatbed shall be outfitted with two cab controlled Trucklite 44101Y alternating flasher lights. These lights shall be located on the rear outside corners of the flatbed |
| 1. |
| The welding of the flat bed or the crane to the chassis is not acceptable. |
| 1. |
| WSDOT expects professional workmanship on all products purchased. With this in mind, the following finishing requirements will be closely scrutinized during the specification compliance inspection. |
| 2. |
| There shall be no welding scale, roughness, sharp corners; or rust stains on the unit. |
| 3. |
| The unit shall be primed then painted with a finish base coat then clear coat. The unit shall be painted L6431 EB Winter White, NAV9219 Winter White BC/CC or equivalent color of white. |
| 1. |
| Each unit shall be delivered with an operator’s, service and parts manuals for both the chassis and the crane. |
| 2. |
| CD’s or DVD’s are acceptable in lieu of manuals. |
| 2. |
| Vendors will provide WSDOT with option prices for various capacity booms and will supply a capacity chart for each unit offered. WSDOT desires lower capacity booms as well as higher capacity booms. |
| 3. |
| List optional reach lengths |
a._____________________ b._____________________ c._____________________ d._____________________
a. $_____________________
b. $_____________________
c. $_____________________ d $._____________________
| 4. |
| Wireless remote system that is capable of operating all crane functions wirelessly |
| 5. |
| 3.5 Metric Ton boom mounted winch. |
| 6. |
| Additional tool circuit at the boom tip for all the various lengths of booms. |
| 7. |
| A Front bumper mounted 20,000 pound Braden (or equal) winch with 100 ft. of appropriately sized wire rope. Shall include a remote pendant with a 20 foot umbilical cord and a four position fair lead. |
| 8. |
| 20,000 pound Braden (or equal) winch mounted to the rear and under the flatbed with 100 ft. of appropriately rated wire rope. Shall include a remote pendant with a 20 foot umbilical cord. |
| 9. |
| Flat bed side mounted Ratcheting winches per each |
| 10. |
| Deduct amount for the Fire Research Lights |
| 11. |
| Deduct amount for Palfinger PK 23502 (or equal) in lieu of PK 26002 EH |
| 12. |
| Aluminum diamond plate decking ILO iron wood |
End of Document Exhibit B Technical Specification TE24004 Crane Truck