Statement of Work .pdf

CUI

STATEMENT OF WORK

FOR

ENVIRONMENTAL WASTE SAMPLING, AND DETERMINATIONS

1.0 SCOPE

The Naval Surface Warfare Center Panama City Division, (NSWC PCD) requires contractor support to sample, conduct waste determinations for each sampled waste stream, and provide laboratory analysis reports. The contractor shall provide all facilities, materials, and labor to accomplish statement of work taskings specified below.

1.1 Acronym List

Following is a list of acronyms used in this Statement of Work.

AQL Acceptable Quality Level CDRL Contract Data Requirements List CFR Code of Federal Regulations COR Contracting Officer’s Representative CUI Controlled Unclassified Information DoD Department of Defense EPA Environmental Protection Agency FAR Federal Acquisition Regulation FOUO For Official Use Only FOIA Freedom of Information Act GFE Government Furnished Equipment GFI Government Furnished Information GFM Government Furnished Material GFP Government Furnished Property GPS Global Positioning System HAZMAT Hazardous Material HM/HW Hazardous Materials/Hazardous Waste IH Industrial Hygiene NMCI Navy and Marine Corps Internet NSA PC Naval Support Activity Panama City OPSEC Operations Security OSHA Occupational Safety and Health

Administration PCO Procuring Contracting Officer PII Personally Identifiable Information PM Program Manager PPE Personal Protection Equipment PSC Product Service Code RCRA Resource Conservation and Recovery Act SDS Safety Data Sheet(s) USN United States Navy

2.0 APPLICABLE DOCUMENTS

The following documents, of the exact issue shown, form a part of this SOW to the extent specified herein. In the event of conflict between the documents referenced and the contents of this SOW, the SOW shall take precedence. Second tier and lower references, (i.e., those referenced in the primary references) shall be used for guidance only.

2.1 Military Specifications: None

2.2 Military Standards: None

2.3 Other Documents:

2.3.1 Title 40 (Protection of Environment), Code of Federal Regulations (CFR), Part 261.

Identification of Hazardous Waste.

2.3.2 Environmental Protection Agency Contract Laboratory Program (EPA CLP) Guidance;

2.3.3 EPA Specifications and Guidance for Contaminant-Free Sample Containers (EPA 540/R-

93/051)

2.3.4 DoD Environmental Laboratory Accreditation Program (ELAP)

2.3.5 NSA Panama City Hazardous Waste Management Plan

3.0 REQUIREMENTS

3.1 Basic Requirements

3.1.1 The Contractor shall provide all labor, materials, and equipment for the collection of process data on waste streams and samples associated with Waste Determination. Collect process data, perform process reviews and waste stream sample collection.

3.1.2 All samples shall be taken from NSWC PCD facilities located at Naval Support Activity

Panama City (NSA PC), and the warehouse located at 1714 Frankford Avenue, Panama City, Fl 32405 as specified in section 3.3 of this SOW. The Frankford Avenue location is designated as “17Warehouse” in Table 2.

3.1.3 Pre submittals

- Sampling Analysis Plan (CDRL A001)

- Plan of Action/Schedule (CDRL A002)

3.1.4 All laboratory analyses shall be performed in accordance with the most recent applicable regulations and guidelines. All laboratory analyses shall be performed by a Certified DOD (DOW) laboratory.

3.1.5 If the Contractor obtains samples requiring additional analysis that must be performed at an alternate laboratory, the Contractor shall prepare samples for shipment, forward the appropriate sub-samples to the other laboratory, and provide final results of analysis to the Technical Point of Contact (TPOC) within the time required by the contract.

3.1.6 The Contractor must have available all the equipment required to perform the analyses as proposed, as well as the equipment needed to prepare the samples for analysis, and refrigerator capacity to store samples before and after analysis.

3.1.7 Chain of Custody (COC) procedures shall be utilized by the laboratory to ensure that sample possession can be traced from the time the sample(s) become the responsibility of the Contractor. COC records shall be maintained by the laboratory for all samples from which the analytical data is required.

3.1.8 Within a laboratory, internal transfers of samples, extracts, and digestates shall be accomplished and documented as controlled custody transfers. The laboratory shall maintain documentation that supports an unbroken chain of custody for samples, digestates and extracts from time of receipt or production in the laboratory until disposal.

3.1.9 Laboratory Quality Control (QC) samples include all analyses stipulated by the analytical method (e.g., method blanks, standards, check samples, laboratory duplicates, matrix spikes, and confirmation analysis), to be included.

3.1.10 The Contractor’s laboratory shall be under the supervision of a qualified chemist, capable of interpreting and directing the analyses to be performed under this contract, and who shall review and certify, by a signed statement on the report form, the adequacy and accuracy of procedures, analytical results and reports. Laboratory personnel, test equipment, consumable chemicals, etc. for the performance of the specified analytical tests are the responsibility of the Contractor and shall be suitable to satisfy the quality of data required; all equipment and procedures used for the performance of the laboratory analyses shall be in conformance with the guidelines established by EPA. The Contractor shall follow the quality control and assurance requirements for the performance of the analytical tests as stated by EPA.

3.1.11 Post Award Kickoff Meeting: The Contractor shall meet with the government POC to coordinate logistics, site visit schedule, sample collection, laboratory for analysis and the Plan of Action/Schedule. Prepare and submit minutes of meeting and the Work Plan/Schedule to the government POC (CDRL A003).

3.1.12 Provide a Sampling and Analysis Plan (SAP) (CDRL A001) and project schedule

(CDRL A002). The SAP will designate the sampling techniques and analytical protocols to be employed for each waste stream with a schedule for accomplishment. Prepare a list of samples required at each of these designated shops for their subsequent field sampling efforts. This project schedule provides proposed dates for visiting each shop for process reviews and collecting the required samples. Prepare a list of personnel that will need to be interviewed during site visits and coordinate with the NSWC PCD hazardous waste program lead to set up these interviews. Prepare a list of interview questions prior to the site visits, and provide these questions to NSWC PCD (CDRL A004).

3.1.13 Waste types to be reviewed include and are not limited to classifications of solid, industrial, universal, non-hazardous & hazardous waste.

3.1.14 Collect all Safety Data Sheets (SDSs) for materials used in the process that is being sampled during the site visit.

3.1.15 The waste samples shall be analyzed as noted in section 3.2. The waste streams to be sampled may be in satellite accumulation containers, process equipment, used oil storage tanks, and/or other hazardous waste accumulation points. Navy personnel will escort the contractor to the sampling locations to collect waste samples and to gather all additional information needed about the waste streams necessary for completion of the Waste determination forms.

3.1.16 The Contractor shall utilize a laboratory approved by state/USEPA and shall submit chain of custodies for samples (CDRL A005) and National Environmental Laboratory Accreditation Program (NELAP) / Certification (NELAC) documentation for laboratory selected for analysis of samples (CDRL A006). Sampling shall conform to USEPA SW 846 Chapter 9 Field Sampling methods.

3.1.17 The Contractor shall ensure full compliance with all state and federal requirements for sample collection and management, turn-around time, holding times, laboratory quality control, sampling plan & USEPA SW 846 Chapter 9 standard operating protocol/best management practices. Contractor is responsible to ensure that all waste samples collected are shipped to the lab in a timely fashion and that samples do not exceed hold time for analysis.

3.1.18 Minimize and properly manage any waste generated as a result of the sampling effort. Properly dispose of any waste generated as a result of the sampling effort. The disposal of non-hazardous waste shall be in accordance with applicable federal, state and local requirements at an approved landfill or treatment facility of the contractor’s choice. The facility shall be licensed for applicable state, federal, and local requirements. Provide proper packaging as specified in 40 CFR 262.30. Submit Weight Log for Non-Hazardous Waste (CDRL A007) and the Hazardous Waste Manifest (CDRL A008) to NSWC PCD. The Hazardous Waste Manifest shall be reviewed and signed by the NSA PC Hazardous Waste Manager before waste leaves the installation to the next destination. The weight log for non-hazardous waste shall be in the format depicted in Attachment 01 – SOLID WASTE DATA LOG.

3.1.19 Contractor shall provide final report that includes quality control review, summary spreadsheet of lab data for all waste streams collected, waste determination using (DLA form 2511) and laboratory report level IV for each waste stream. In addition to the final report, submit the original lab reports and summary spreadsheet identifying applicable waste codes and underlying hazardous constituents of waste streams collected. (CDRL A009). The waste determination shall be in the format of Attachment 02 – DLA FORM

2511 HAZARDOUS WASTE PROFILE SHEET.

3.1.20 Contractor shall provide electronic copy and two hard copies to all post submittals in section 3.1.22.

3.1.21 Post submittals:

- Final Report (CDRL A009)

- Spreadsheet of all waste streams collected (CDRL A010)

- Digital versions of laboratory reports and quality control (CDRL A011)

- Waste determination for each sample (CDRL A012)

3.2 Waste Analysis

Commercial test types that may be performed on this contract include the following:

Table 1. Hazardous Waste Quantity Analytical Description Analytical Method Level

(13) VOC / Semi VOC / Metals and Mercury in liquid SW846 8260/8270/6010/7470 IV

(8) Metal Target Analyte List (TAL) SW846 6010/7470 IV

(9) Metals (Mercury) and VOC SW 846 8260/6010/7470 IV

(2) Metal (TAL List) SW846 6010/7471 IV

(11) Full TCLP SW 846 1311 IV

(5) VOC and Semi VOC SW846 8260/8270 IV

(4) Flashpoint SW846 1030 - Ignitability IV

3.3 Base Service

The Contractor at a minimum shall take samples, conduct waste determinations for each sampled waste stream, and provide laboratory analysis report from Table 2 below.

Table 2. Waste Sample Name

B47 - Paint Solid Debris B47- Paint Filter Waste B47- MEK and Paint Waste B47- Bead Blast Waste B47 - Pain gun cleaner B319-MEK Rags and solid B319- Oily Rags B374- Printer Ink Waste B414 - Protein Sequencing B414 - IPA Wash B431 - Metal 3D printer waste B431 -Used paint filters AM Lab B431 - Parts washer waste AM Lab B431- Oily Rags Machine Shop B431 - Parts Washer Machine Shop B431 - Spent Blast Media Machine Shop B431 - EDM Sludge Machine Shop B431 - Water Jet Sludge Machine Shop B431 - Ultrasonic Cleaner Passivation

Table 2. Waste Sample Name

B431 - Spent Blast Media Plastic Shop B431 - Waste MEK Rags Plastic Shop B431- Waste Parts Washer Solvent Plastic Shop B431 - Oily Rags Plastic Shop B431 - Methylene Chloride Quality Lab B431- Spent Bead Blast Rigging Shop B431- Spent Blast Media Structural Shop B431 - Waste TCE rags Structural Shop B460 - Rags B470 - Form Wash Waste B490 - Spent Parts Washer B490 - Oily Rags B495 - Spent Parts Washer Solution B528 - Spent Parts Washer B543 - Spent Parts Washer B581 - Oily Rags High Bay B582 - Spent Bead Blast Waste B582 -Spent Parts Washer Solvent B582 - Parts Washer B589 - Gas filter waste B609 - Form wash waste B658 - Form wash waste (Metal) T2093 - Spent Parts Washer 17Warehouse - Oily rags waste 17Warehouse - Spent Blast media waste 17Warehouse - Spent Blast media filter waste 17Warehouse - Small Parts Washer

As a minimum, use nomenclature in Table 2. Each entry shall include the building number, sample number per the chain of custody, and waste stream name provided in Table 2. Name convention per waste streams: Example: ‘B47-001-Paint Solid Debris’

4.0 GOVERNMENT FURNISHED PROPERTY

4.1 Government Furnished Equipment (GFE): None

4.2 Government Furnished Information (GFI): None

4.3 Government Furnished Material (GFM): None

5.0 DATA DELIVERABLES

Data shall be provided in accordance with the Contract Data Requirements List (CDRL) DD Form 1423.

6.0 PERIOD OF PERFORMANCE

Period of Performance: The service shall be completed no later than sixteen weeks after receipt of award.

7.0 SECURITY

This task involves access to Controlled Unclassified Information (CUI). Performance under this contract shall NOT require access to nor generate CLASSIFIED information.

7.1 Release of Information

(a) Release of information shall be in accordance with Section I, DFARS Clause 252.204-7000, Disclosure of Information.

(b) All technical data provided to the contractor by the Government shall be protected from public disclosure in accordance with the markings contained thereon. All other information relating to the items to be delivered or services to be performed under this task order may not be disclosed by any means without prior approval of the appropriate NSWC PCD authority.

Dissemination or public disclosure includes, but is not limited to, permitting access to such information by foreign nationals or by any other person or entity; publication of technical or scientific papers; advertising; or any other proposed public release. The contractor shall provide adequate physical protection to such information to preclude access by any person or entity not authorized such access by the Government.

7.2 Controlled Unclassified Information (CUI)

Controlled unclassified information (CUI) is official information that requires the application of controls and protective measures for a variety of reasons and has not been approved for public release, to include technical information, proprietary data, information requiring protection under the Privacy Act of 1974, and Government-developed privileged information involving the award of contracts. CUI is a categorical designation that refers to unclassified information that does not meet the standards for National Security Classification under Executive Order 13526, but is (a) pertinent to the national interest of the United States or to the important interests of entities outside the Federal Government, and (b) under law or policy requires protection from unauthorized disclosure, special handling safeguards, or prescribed limits on exchange or dissemination.

7.3 Minimum Requirements for Access to Controlled Unclassified Information (CUI)

Access to CUI, user level access to DON or DoD networks and information systems, system security and network defense systems, and to system resources providing visual access and/or ability to input, delete or otherwise manipulate sensitive information without controls to identify and deny sensitive information, requires security clearance eligibility, based on a Tier 3 Background Investigation, and a favorable adjudication by the Defense Counterintelligence and Security Agency, Consolidated Adjudications (DCSA CAS), or Interim/Temporary access to CUI based on a determination by the NSWC PCD Security Manager based on a favorable review of an individuals completed Electronic Questionnaire for Investigation Processing (SF 86), and favorable FBI fingerprint results. Contact NSWC PCD Personnel Security (NSWCPCD_PERSEC@us.navy.mil) for initiation of the SF86 and FBI fingerprinting, the CUI determination, and validation that employees have the required eligibility, prior to providing access to CUI.

7.4 Minimum Protection Requirements for Controlled Unclassified Information

Security classification guides and unclassified limited documents (e.g., CUI, Distribution Statement Controlled) are not authorized for public release and, therefore, cannot be posted on a publicly accessible webserver or transmitted over the Internet unless appropriately encrypted.

7.5 CUI

CUI is a designation, not a classification. CUI is used by Department of Defense (DoD) and a number of other federal agencies to identify information or material, which although unclassified, disclosure to the public of the information would reasonably be expected to cause a foreseeable harm to an interest protected by one or more provisions of the FOIA. This includes information that qualifies for protection pursuant to the provisions of the Privacy Act of 1974, as amended. CUI must be marked, controlled and safeguarded in accordance with DoDI 5200.48, DoD Information Security Program: Controlled Unclassified Information (CUI).

7.6 Security of Unclassified DoD Information on Non-DoD Information Systems (DoDI

8582.01) DoD Policy

7.6.1 DoD Policy

Adequate security shall be provided for all unclassified DoD information on non-DoD information systems. Appropriate requirements shall be incorporated into all contracts, grants, and other legal agreements with non-DoD entities.

Information Safeguards are applicable to unclassified DoD information in the possession or control of non-DoD entities on non-DoD information systems, to the extent provided by the applicable contract, grant, or other legal agreement with the DoD.

7.6.2 Information Safeguards

mailto:NSWCPCD_PERSEC@us.navy.mil

Unclassified DoD information that has not been cleared for public release may be disseminated by the contractor, grantee, or awardee to the extent required to further the contract, grant, or agreement objectives, provided that the information is disseminated within the scope of assigned duties and with a clear expectation that confidentiality will be preserved. Examples include:

a. Non-public information provided to a contractor (e.g., with a request for proposal).

b. Information developed during the course of a contract, grant, or other legal agreement (e.g., draft documents, reports, or briefings and deliverables).

c. Privileged information contained in transactions (e.g., privileged contract information, program schedules, contract-related event tracking).

Note: It is recognized that adequate security will vary depending on the nature and sensitivity of the information on any given non-DoD information system. However, all unclassified DoD information in the possession or control of non-DoD entities on non-DoD information systems shall minimally be safeguarded as follows:

a. Do not process unclassified DoD information on publicly available computers (e.g., those available for use by the general public in kiosks or hotel business centers).

b. Protect unclassified DoD information by at least one physical or electronic barrier (e.g., locked container or room, logical authentication or logon procedure) when not under direct individual control of an authorized user.

c. At a minimum, overwrite media that have been used to process unclassified DoD information before external release or disposal.

d. Encrypt all information that has been identified as CUI when it is stored on mobile computing devices such as laptops and personal digital assistants, compact disks, or authorized removable storage media such as thumb drives and compact disks, using the best encryption technology available to the contractor or teaming partner.

e. Limit transfer of unclassified DoD information to subcontractors or teaming partners with a need to know and obtain a commitment from them to protect the information they receive to at least the same level of protection as that specified in the contract or other written agreement.

f. Transmit e-mail, text messages, and similar communications containing unclassified DoD information using technology and processes that provide the best level of privacy available, given facilities, conditions, and environment. Examples of recommended technologies or processes include closed networks, virtual private networks, public key-enabled encryption, and transport layer security (TLS).

g. Encrypt organizational wireless connections and use encrypted wireless connections where available when traveling. If encrypted wireless is not available, encrypt document files (e.g., spreadsheet and word processing files), using at least application-provided password protected level encryption.

h. Transmit voice and fax transmissions only when there is a reasonable assurance that access is limited to authorized recipients.

i. Do not post unclassified DoD information to website pages that are publicly available or have access limited only by domain or Internet protocol restriction. Such information may be posted to website pages that control access by user identification and password, user certificates, or other technical means and provide protection via use of TLS or other equivalent technologies during transmission. Access control may be provided by the intranet (vice the website itself or the application it hosts).

j. Provide protection against computer network intrusions and data exfiltration, minimally including:

(1) Current and regularly updated malware protection services, e.g., anti-virus, anti-spyware.

(2) Monitoring and control of both inbound and outbound network traffic (e.g., at the external boundary, sub-networks, individual hosts), including blocking unauthorized ingress, egress, and exfiltration through technologies such as firewalls and router policies, intrusion prevention or detection services, and host-based security services.

(3) Prompt application of security-relevant software patches, service packs, and hot fixes.

k. Comply with other current Federal and DoD information protection and reporting requirements for specified categories of information (e.g., medical, proprietary, critical program information (CPI), personally identifiable information, export controlled) as specified in contracts, grants, and other legal agreements.

l. Report loss or unauthorized disclosure of unclassified DoD information in accordance with contract, grant, or other legal agreement requirements and mechanisms.

m. Do not use external IT services (e.g., e-mail, content hosting, database, document processing) unless they provide at least the same level of protection as that specified in the contract or other written agreement.

7.7 Operations Security

Operations Security (OPSEC) is concerned with the protection of critical information: facts about intentions, capabilities, operations, or activities that are needed by adversaries or competitors to bring about failure or unacceptable consequences of mission accomplishment.

Critical information includes information regarding:

• Operations, missions, and exercises, test schedules or locations;

• Location/movement of sensitive information, equipment, or facilities;

• Force structure and readiness (e.g., recall rosters);

• Capabilities, vulnerabilities, limitations, security weaknesses;

• Intrusions/attacks of DoD networks or information systems;

• Network (and system) user IDs and passwords;

• Movements of key personnel or visitors (itineraries, agendas, etc.); and

• Security classification of equipment, systems, operations, etc.

The contractor, subcontractors and their personnel shall employ the following countermeasures to mitigate the susceptibility of critical information to exploitation, when applicable:

• Practice OPSEC and facilitate OPSEC awareness;

• Immediately retrieve documents from printers accessible by the public;

• Shred sensitive and Controlled Unclassified Information (CUI) documents when no longer needed;

• Protect information from personnel without a need-to-know;

• When promulgating information, limit details to that essential for legitimacy;

• During testing and evaluation, practice OPSEC methodologies of staging out of sight, desensitization, or speed of execution, whenever possible.

8.0 GOVERNMENT AND CONTRACTOR RELATIONSHIP

(a) The services to be delivered under this Task Order are non-personal services and the parties recognize and agree that no employer-employee relationship exists or will exist under the Task Order between the Government and the Contractor's personnel. It is, therefore, in the best interest of the Government to afford both parties a full understanding of their respective obligations.

(b) All Contractor, Subcontractor, and consultant personnel shall wear prominently displayed identification badges at all times when performing work on NSWC PCD property or attending meetings in the performance of this Task Order. The badge shall contain the individual's name, the company name and logo. When participating in such meetings (e.g., as a speaker, panel member), those individuals in Contractor employ must supplement physical identification (e.g., badges, place markers) with verbal announcements so that it is clear to the assembled group that they are employees of the Contractor, not NSWC PCD employees. In addition, when working on NSWC PCD property, all Contractor, Subcontractor, and consultant personnel shall have signs visible on their desks or at their work sites that clearly state that they are not NSWC PCD employees.

(c) The Contractor is responsible for supervision of all Contractor personnel assigned to this

Task Order. The Contractor shall exercise ultimate over all aspects of Contractor personnel day-to-day work under this Task Order including the assignment of work, means and manner of Contractor employee performance and the amount of Contractor supervision provided. The Contractor shall be ultimately responsible for all aspects of performance under this Task Order including the work of its Contractor personnel.

Contractor personnel under this Task Order shall not:

(1) Be placed in a position where they are under the supervision, direction, or evaluation of a Government employee.

(2) Be placed in a position of command, supervision, administration or control over Government personnel, or over personnel of other Contractors under other NSWC PCD contracts, or become a part of the Government organization.

(3) Be used in administration or supervision of Government procurement activities.

(4) Have access to proprietary information belonging to another without the express written permission of the owner of that proprietary information.

(d) Employee Relationship:

(1) The services to be performed under this Task Order do not require the Contractor or its personnel to exercise personal judgment and discretion on behalf of the Government. Rather the Contractor's personnel will act and exercise personal judgment and discretion on behalf of the Contractor.

(2) Rules, regulations, directives and requirements that are issued by the U.S. Navy and NSWC PCD under its responsibility for good order, administration, and security are applicable to all personnel who enter the Government installation or who travel on Government transportation. This is not to be construed or interpreted to establish any degree of Government control that is inconsistent with non-personal services Task Order.

(e) Inapplicability of Employee Benefits: This Task Order does not create an employer-employee relationship. Accordingly, entitlements and benefits applicable to such relationships do not apply.

(1) Payments by the Government under this Task Order are not subject to the Federal income tax withholdings.

(2) Payments by the Government under this Task Order are not subject to the Federal Insurance Contributions Act.

(3) The Contractor is not entitled to unemployment compensation benefits under the Social Security Act, as amended, by virtue of performance of this Task Order.

(4) The Contractor is not entitled to workman's compensation benefits by virtue of this Task Order.

(5) The entire consideration and benefits to the Contractor for performance of this Task Order are contained in the provisions for payment under this Task Order.

(f) Notice. It is the Contractor's, as well as, the Government's responsibility to monitor Task

Order activities and notify the Contracting Officer if the Contractor believes that the intent of this clause has been or may be violated.

(1) The Contractor should notify the Contracting Officer in writing promptly, within three

(3) calendar days from the date of any incident that the Contractor considers to constitute a violation of this clause. The notice should include the date, nature, and circumstances of the conduct, the name, function and activity of each Government employee or Contractor official or employee involved or knowledgeable about such conduct, identify any documents or substance of any oral communication involved in the conduct, and the estimate in time by which the Government must respond to this notice to minimize cost, delay or disruption of performance.

(2) The Contracting Officer shall promptly, within five (5) calendar days after receipt of notice, respond to the notice in writing. In responding, the Contracting Officer will either:

(i) confirm the conduct is in violation and when necessary direct the mode of further performance,

(ii) countermand any communication regarded as a violation

(iii) deny that the conduct constitutes a violation and when necessary direct the mode of further performance; or

(iv) in the event the notice is inadequate to make a decision, advise the Contractor what additional information is required, and establish the date by which it should be furnished by the Contractor and the date.

9.0 DISTRIBUTION LIMITATION STATEMENT

Distribution Statements and Warning Notices: The Contractor shall place the appropriate Distribution Statement on information associated/generated with this contractual effort, per the applicable Security Classification Guide, and carry forward the markings on documents provided by the government, along with the following statements on all technical documents/media, as applicable.

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DOD AND

U.S. DOD CONTRACTORS ONLY: ADMINISTRATIVE/OPERATIONAL USE

(DATA STATEMENT APPLIED). OTHER REQUESTS SHALL BE REFERRED TO

COMMANDING OFFICER, NAVAL SURFACE WARFARE CENTER PANAMA

CITY DIVISION, ATTN: CODE 1031, 110 VERNON AVE., PANAMA CITY, FL

32407-7001

DESTRUCTION NOTICE - CLASSIFIED INFORMATION, DESTROY IN

ACCORDANCE WITH SECNAV M-5510.36, (DON INFORMATION SECURITY

PROGRAM) OR NISPOM RULE. UNCLASSIFIED LIMITED DOCUMENTS, (E.G.,

FOUO, DISTRIBUTION STATEMENT CONTROL) DESTROY BY ANY METHOD

THAT WILL PREVENT DISCLOSURE OF CONTENTS OR RECONSTRUCTION

OF THE DOCUMENT.

--- END OF STATEMENT OF WORK ---