SRC0000013690 ITB.pdf

STATE OF OHIO

DEPARTMENT OF ADMINISTRATIVE SERVICES

GENERAL SERVICES DIVISION

OFFICE OF PROCUREMENT SERVICES

4200 SURFACE ROAD, COLUMBUS, OH 43228-1395

MANDATORY USE CONTRACT FOR: Mattress and Furniture Materials; Foam Cores, Fabrics, and Other Components

CONTRACT No.: ITB018851

CONTRACT ID: 18851

EFFECTIVE DATES: 5/1/2024 to 4/30/2027

SUPPLIER: UNDEFINED

The Department of Administrative Services has accepted bids submitted in response to Invitation to Bid No.

SRC0000013690. The evaluation of the bid response(s) has been completed. The bidder(s) listed herein have been determined to be the lowest responsive and responsible bidder(s) and have been awarded a contract for the items(s) listed. The respective bid response, including the Instructions to Bidders and Standard Terms and Conditions, special contract terms & conditions, any bid addenda, specifications, pricing schedules and any attachments incorporated by reference and accepted by DAS become a part of this Requirements Contract.

This Requirements Contract is effective beginning and ending on the dates noted above unless, prior to the expiration date, the Contract is renewed, terminated or cancelled in accordance with the Contract Terms and Conditions.

CONTRACT RENEWAL This Contract may be renewed after the ending date of the Contract solely at the discretion of the Contracting Agency for a period of one month. Any further renewals will be by mutual agreement between the Contractor and the Contracting Agency for any number of times and for any period of time. The cumulative time of all mutual renewals may not exceed 24 months unless the Contracting Agency determines that additional renewal is necessary.

This Requirements Contract is available to the Ohio Department of Rehabilitation and Correction, as applicable.

Agencies are eligible to make purchases of the listed supplies and/or services in any amount and at any time as determined by the agency. The State makes no representation or guarantee that agencies will purchase the volume of supplies and/or services as advertised in the Invitation to Bid.

This Requirements Contract and any Amendments thereto are available from the OhioBuys public portal at the following address:

https://ohiobuys.ohio.gov/page.aspx/en/usr/login?ReturnUrl=%2fpage.aspx%2fen%2fbuy%2fhomepage

Signed: _____________________________________________________________________ Kathleen C. Madden, Director Date https://ohiobuys.ohio.gov/page.aspx/en/usr/login?ReturnUrl=%2fpage.aspx%2fen%2fbuy%2fhomepage

1 - SPECIFICATIONS AND REQUIREMENTS

1.1 SCOPE The purpose of this solicitation is to establish a Contract(s) to procure supplies and materials as required by the Ohio Penal Industries (OPI) mattress and furniture shops. These supplies and materials are to be used to fabricate various items as listed in the following sections. These items include, but may not be limited to, mattresses and pillows for high risk and public occupancy applications, foam materials to be used in the fabrication of chairs for general seating applications, and clear vinyl fabrics to be used in both the fabrication of shower curtains for high-risk institution applications and tote and lunch bags for general use applications.

1.2 CATEGORIES The following categories of supplies are required for the fabrication operations.

1.2.1 CATEGORY I: Neoprene Foam

1.2.2 CATEGORY II: Polyurethane Foam

1.2.3 CATEGORY III: Neoprene Encapsulated High-Density Polyurethane Foam

1.2.4 CATEGORY IV: Polyethylene Foam

1.2.5 CATEGORY V: Thermally Bonded Polyester Fiber

1.2.6 CATEGORY VI: Polyester Pillow Batting

1.2.7 CATEGORY VII: Innerspring Mattress Unit

1.2.8 CATEGORY VIII: Perm-a-lator Style Wire Spring Insulator

1.2.9 CATEGORY IX: Bonded Polyester Upholstery Fiber

1.2.10 CATEGORY X: Polyester Fabric

1.2.11 CATEGORY XI: Clear Vinyl Fabric

1.2.12 CATEGORY XII: Scrim Based Vinyl Fabrics and Adhesive

1.3 GENERAL REQUIREMENTS

1.3.1 Intended Use This solicitation identifies the intended use of these products; however, there may be instances where these supplies and materials will be used in the fabrication of products other than the intended use specified herein. The Contractor(s) shall assist the Agency, in good faith, if consulted regarding any material’s fitness for use in a manner other than originally identified.

1.3.2 Packaging Each item shall be packaged as described per product with the intent that the materials arrive in good order without becoming damaged, soiled or otherwise contaminated.

1.3.3 Labelling Each package shall indicate the type of material, size, Contractor's name, and the name of the institution/agency.

1.3.4 Units of Measure The unit of measure (UOM) may vary by product category and even by item within a product category. The Contractor shall follow the UOM as listed and ordered by the Agency.

1.3.5 Industry Standard Unspecified details herein are to be in accordance with the acceptable standard commercial and industry practices for products of this type.

1.3.6 Liquid Resistance Products fire resistance properties shall not be affected by exposure to water or other liquids.

1.4 PRODUCT SPECIFICATIONS AND REQUIREMENTS

1.4.1 CATEGORY I: Neoprene Foam

1.4.1.1 Intended Use The neoprene foam required by this specification is intended to be used as follows for high risk and public occupancy applications.

1.4.1.1.1 Mattress cores Various sizes and thicknesses of rectangular neoprene pads to be used as mattress cores.

1.4.1.1.2 Topper Pads Thinner than the mattress cores, these rectangular neoprene pads are used as top pads for additional padding when assembling full mattresses.

1.4.1.1.3 Pillow tops Formed neoprene components shaped to resemble a pillow to be adhered to other mattress core materials.

1.4.1.2 Material The material shall be Neoprene (polychloroprene) cellular flexible cushioning, suitable for the intended use, processed to meet or exceed all the flammability and physical characteristics stated herein. The materials shall contain no normal or reclaimed rubber.

1.4.1.3 Physical Properties

1.4.1.3.1 Construction The material shall have a homogeneous cellular structure with a porous surface, open cells, and flat surface. The cells shall be interconnecting and uniform in size. The form of the material shall be sheets or molded shapes.

1.4.1.3.2 Physical Properties and Testing Methods The material shall comply with the following standards.

Physical Properties

Property Test Method Value

Density ASTM-D3574 6.2 to 6.7 lbs./cu ft

Indentation Force Deflection (IFD) ASTM-D3574 Medium 40 +/- 5 lbs.

Compression Set ASTM-D3574 50% constant deflection Percent of Original Thickness

10% maximum

Elongation ASTM-D3574 150% Minimum

Tensile ASTM-D3574 8 lbs./Sq. In. Minimum

Tear Strength ASTM-D3574 2.0 lbs./in. Minimum

Flex Fatigue ASTM-D1055 As Specified

Thickness Loss Percent of Original Thickness 5% maximum

Indentation Measure IFD per ASTM-D3574 after one hour rest – compared to original

35% maximum

Resiliency ASTM-D3574 30% Minimum

Fungal Growth ASTM G-21 No Growth

1.4.1.3.3 Flame Resistance Characteristics and Testing Methods The material shall comply with all the following flammability characteristics.

Flammability Characteristics

Radiant Panel ASTM D3675 Maximum flame index – 5 No melting or dripping

NBS Smoke Chamber ASTM E662 Flaming & Non-Flaming modes 1" sample

Ds 90 seconds 100 maximum Ds 4 minutes 175 maximum D maximum 200 maximum

Rate of Heat Release ASTM E1354

(a) Radiant Flux 35 kW/m2

(b) Horizontal Mode (2n sample)

Run with an Edge Frame

Peak Heat Release Rate – 75 kW/m2 maximum

3 Minute Average Heat Release Rate – 30 kW/m2 maximum

Mattress Insert Test Michigan Roll (Insert Only)

ASTM F1085 Annex A3 (Also referenced in ASTM F1870 Paragraph 10.1 & 10.2) Total weight loss (%)

7% maximum weight loss Must maintain shape with no generation of molten material

Composite Mattress Tests

California TB No. 121 California TB No. 129 16 CFR Part 1633

Pass Pass

1.4.1.3.4 Finish and Color Both the color and finished surface of the material shall be in accordance with the industry standard.

1.4.1.3.5 Workmanship The product shall be of uniform texture and shall be free from any obvious manufacturing imperfections which may impair its serviceability.

1.4.1.3.6 Odor The material shall be properly cured to prevent any objectionable odor. It shall be given adequate airing by a moving current of air to completely remove all volatile matter.

1.4.1.3.7 Size The size varies by item as listed in the bid item grid.

1.4.1.4 Packaging The packaging shall be standard to the industry. Cores, pads and toppers shall be wrapped in Kraft paper, poly bag, or any other strong wrapping material to provide safe transport to the using location.

1.4.2 CATEGORY II: Polyurethane Foam

1.4.2.1 Intended Use: The polyurethane foam required by this specification is intended for the use in the fabrication of chairs for general seating applications.

1.4.2.2 Material The polyurethane foam shall be made from polyhydroxy compounds, isocyanates, and water combined in a reaction to form an expanded flexible open cell product.

1.4.2.2.1 Auxiliary Expanding Agents Auxiliary expanding agents such as halogenated hydrocarbons are acceptable.

1.4.2.2.2 Additives Additives designed to lessen combustibility of foams are acceptable.

Bidders shall identify additives when submitting bids for this category.

1.4.2.2.3 Fillers Fillers of inert mineral powders such as calcium carbonate, barium sulfate, zirconium silicate, or alumina trihydrate are acceptable. Bidders shall identify fillers when submitting bids for this category.

1.4.2.3 Physical Properties

1.4.2.3.1 Construction The foam must be formed into sheets.

1.4.2.3.2 Physical Properties and Testing Methods

Density ASTM-D3574, Test A 1.6 lbs./cu ft Minimum

Indentation Force Deflection

(IFD)

Support factor

ASTM-D3574, Test B1 ratio of 65 percent IFD to 25 percent IFD

Bidders shall identify test values of products bid

Compression Set ASTM-D3574, Test D 75% constant deflection Percent of Original Thickness

15% Maximum

Elongation ASTM-D3574, Test E 120% Minimum

Tensile ASTM-D3574, Test E 12 lbs./sq In, Minimum

Thickness Loss Percent of Original Thickness 5% Maximum

Indentation Measure IFD per ASTM-D3574 after one hour rest – compared to original

35% Maximum

Steam Autoclave properties after aging

ASTM-D3574, Test J Force Deflection Constant Deflection Compression Set

20% Maximum 15% Maximum

1.4.2.3.3 Flame Resistance Characteristics and Testing Methods Combustibility, polyurethane foams are to meet the specified requirements of California Technical Bulletin 133;

Requirements, California Technical Bulletin 117, Test Procedure and Apparatus for Testing the Flame Retardance of Resilient Filling Materials Used in Upholstered Furniture.

1.4.2.3.4 Finish and Color Both the color and finished surface of the material shall be in

1.4.2.3.5 Workmanship The polyurethane foam is to be uniform in mechanical properties. The finished product is to be free of non-expanded resin and is to show no defects which may affect its serviceability.

1.4.2.3.6 Odor The material shall be properly cured to prevent any objectionable odor. It shall

1.4.2.3.7 Size The size varies by item as listed in the bid item grid.

• Tolerance, Length and Width The material shall be within +/-1/2” of this size listed for both length and width.

• Tolerance, Thickness The material thickness shall be as follows.

o 1/4” to 1-1/2” thick material shall be within +/-1/16.”

• 1-1/2” to 3" thick material shall be within +/-1/8.”

• 3" to 5" thick material shall be within +/-3/16.”

1.4.2.4 Packaging The packaging shall be standard to the industry. The sheets should be wrapped in poly bags, or any other strong wrapping material to provide safe transport to the using location.

1.4.3 CATEGORY III: Neoprene Encapsulated High-Density Polyurethane Foam

1.4.3.1 Intended Use The neoprene encapsulated high-density polyurethane foam required by this specification is intended to be used as mattress cores in the fabrication of mattresses for high risk and public occupancy applications.

1.4.3.2 Material

1.4.3.2.1 Neoprene Foam The material shall be neoprene (polychloroprene) cellular flexible cushioning, suitable for the intended use, processed to meet or exceed all the flammability and physical characteristics stated herein. The materials shall contain no normal or reclaimed rubber.

1.4.3.2.2 High-density Polyurethane Foam

1.4.3.3 Physical Properties

1.4.3.3.1 Construction A 1/2” minimum of fire-resistant, medium firmness neoprene foam shall completely encapsulate a high-density polyurethane foam. An acceptable solution is the construction of a rectangular neoprene “box” by means of a “neoprene” water-based adhesive with the polyurethane foam contained inside.

1.4.3.3.2 Physical Properties and Testing Methods The material shall comply with the following

Density ASTM-D3574 6.2 to 6.7 lbs./cu ft

Indentation Force Deflection (IFD) ASTM-D3574 Medium 40 +/- 5 lbs.

Compression Set ASTM-D3574 50% constant deflection Percent of Original Thickness

10% maximum

Elongation ASTM-D3574 150% Minimum

Tensile ASTM-D3574 8 lbs./Sq. In. Minimum

Tear Strength ASTM-D3574 2.0 lbs./in. Minimum

Flex Fatigue ASTM-D1055

Thickness Loss Percent of Original Thickness 5% maximum

Indentation Measure IFD per ASTM D3574 after one hour rest – compared to original

25% maximum

Resiliency ASTM-D3574 30% Minimum

Fungal Growth ASTM G-21 No Growth

1.4.3.3.3 Flame Resistance Characteristics and Testing Methods The flammability characteristics for the cushioning shall not be affected by exposure to liquids. The high-density neoprene fire resistant cushioning shall be used to ensure compliance to applicable full scale mattress performance criteria and to enhance the support, integrity, and longevity of the mattress. The fire-resistant exterior cushioning must comply with the following physical and fire-performance properties and the finished/covered mattress shall comply with the established full scale fire performance criteria. The material shall comply with all of the following flammability characteristics.

Flammability Characteristics

Radiant Panel ASTM D3675 Maximum flame index – 5 No melting or dripping

NBS Smoke Chamber ASTM E662 Flaming & Non-Flaming modes 1" sample

Ds 90 seconds 100 maximum Ds 4 minutes 175 maximum D maximum 200 maximum

Rate of Heat Release ASTM E1354

(a) Radiant Flux 35 kW/m2

(b) Horizontal Mode (2n sample) Run with an Edge Frame

Peak Heat Release Rate – 75 kW/m2 maximum

3 Minute Average Heat Release Rate

– 30 kW/m2 maximum

Composite Mattress Test ASTM E1590 Heat release rate – 35 kW maximum Heat release rate at 10 minutes –

10 MJ maximum

Composite Mattress Tests

California TB No. 129 Boston BFD IX-11 16 CFR Part 1633

Pass

1.4.3.3.4 Finish and Color Both the color and finished surface of the material shall be in

1.4.3.3.5 Workmanship The product shall be of uniform texture and shall be free from any

1.4.3.3.6 Odor The material shall be properly cured to prevent any objectionable odor. It shall

1.4.3.3.7 Size The size varies by item as listed in the bid item grid.

1.4.3.4 Packaging The packaging shall be standard to the industry. The cores should be wrapped in poly bags, or any other strong wrapping material to provide safe transport to the using

1.4.4 CATEGORY IV: Polyethylene Foam

1.4.4.1 Intended Use The polyethylene foam required by this specification is intended for the use as border foam in the fabrication of mattresses for high risk and public occupancy applications.

1.4.4.2 Material The material must consist of 100% polyethylene foam suitable for the intended use.

1.4.4.3 Physical Properties

1.4.4.3.1 Construction The foam shall be manufactured into uniform continuous strips ¼” thick of either 4” or 6” in width.

1.4.4.3.2 Workmanship The product shall be of uniform texture and shall be free from any

• The foam must maintain the required dimensions.

• This foam may be provided in rolls wider than of the specified size if the foam is slit at the appropriate width.

1.4.4.3.3 Odor The material shall be properly cured to prevent any objectionable odor. It shall be given adequate airing to completely remove all volatile matter.

1.4.4.3.4 Size The size varies by item as listed in the bid item grid.

1.4.4.4 Packaging The polyethylene foam shall be furnished rolled onto cores with plastic waterproof covering suitable to provide safe transport to the using location.

1.4.5 CATEGORY V: Thermally Bonded Polyester Fiber

1.4.5.1 Intended Use The thermally bonded polyester fiber required by this specification is intended for the use as mattress cores in the fabrication of mattresses for high risk and public occupancy applications.

1.4.5.2 Material The material shall consist of thermally bonded 100% polyester polymer fiber suitable for the intended use.

1.4.5.2.1 The mattress cores are to be composed of low melt polyester/polyester sheath core binder fiber, produced using new, unused currently standard raw materials.

Reprocessed scrap from the manufacturing process is acceptable and may be considered new and unused.

1.4.5.2.2 The material is to contain no glues, resins, adhesives, fillers, additives, or other chemicals.

1.4.5.3 Physical Properties

1.4.5.3.1 Construction The mattress core shall be one piece without splicing or lamination.

1.4.5.3.2 Physical Properties and Testing Methods

• Performance The mattress core shall retain its original shape in the area of body weight with minimal thickness loss.

• Weight/Density The total weight/density shall be 10 ounces per square foot.

• The cores shall be hypoallergenic.

1.4.5.3.3 Flame Resistance Characteristics and Testing Methods

• Mattress Cores All mattress cores shall pass the testing required by the following o California Technical Bulletin #117 o 16 C.F.R. 1633.

1.4.5.3.4 Finish and Color The surface of the mattress core must be flat and uniform, without imperfections adversely impacting appearance, function or durability.

1.4.5.3.5 Workmanship The product shall be of uniform texture and shall be free from any

1.4.5.3.6 Odor The cores shall be odor free, containing no volatile organic compounds (VOCs).

1.4.5.3.7 Size The size shall be as listed in the bid item grid.

• Tolerance, Length and Width The material shall be provided in the length and width as listed.

• Tolerance, Thickness The material shall be provided within +/-1/2” of the thickness listed.

1.4.5.3.8 Packaging The packaging is to be standard for the industry. Cores are to be wrapped in poly bag or any other strong wrapping material so that the insert is neither damaged nor contaminated.

1.4.6 CATEGORY VI: Polyester Pillow Batting

1.4.6.1 Intended Use The pillow batting required by this specification is intended for the use in the fabrication of pillows for high risk and public occupancy applications.

1.4.6.2 Material The pillow batting must be composed of low melt polyester/polyester sheath core binder fiber. The batting must be produced using new, unused, currently standard product (raw material). Reprocessed scrap from the manufacturing process is acceptable and may be considered new and unused.

1.4.6.3 Physical Properties

1.4.6.3.1 Physical Properties and Testing Method

• Performance The batting must retain its original shape with minimal thickness loss.

• Weight/Density The total weight/density of the batting must be 2 ounces per square foot.

• The batting must be hypoallergenic.

1.4.6.3.2 Flame Resistance Characteristics and Testing Methods The batting must pass the testing required by the following standards.

• California Technical Bulletin #117

▪ 16 C.F.R. 1633.

1.4.6.3.3 Finish and Color The surface of the batting must be uniform, without imperfections adversely impacting appearance, function or durability.

1.4.6.3.4 Workmanship The batting shall be of uniform texture and shall be free from any

1.4.6.3.5 Odor The batting must be odor free and contain no VOCs.

1.4.6.3.6 Size The size shall be as listed in the bid item grid.

• Tolerance, Length and Width The material shall be provided within +/-1/4” of the length and width as listed.

• Tolerance, Thickness The material shall be provided within +/-1/2” of the thickness listed.

1.4.6.4 Packaging The pillow batting must be furnished in rolls, wrapped in a poly bag or other suitably strong wrapping material standard to the industry so the product is neither damaged nor contaminated.

1.4.7 CATEGORY VII: Innerspring Mattress Unit

1.4.7.1 Intended Use The innerspring mattress units required by this specification are intended for the use as mattress cores in the fabrication of mattresses for high risk and public occupancy applications.

1.4.7.2 Material The mattress unit shall be assembled from all steel components.

1.4.7.3 Physical Properties

1.4.7.3.1 Construction

• Coils Coil wire must be high carbon spring steel, hard drawn American Steel grade or equal with tensile strength specifications of 205,000 PSI minimum and 275,000 PSI maximum.

o All coils must be Bonnell type and are to have no fewer than three (3) turns/convolutions (five counting top and bottom).

o Perimeter coils (outside rows) are to be a minimum of 13 gauge and interior coils (middle six (6) rows) are to be a minimum of 13.5 gauge.

o Standard length units (74.5”) shall have a minimum of 208 coils and long length units shall have a minimum of 252 coils.

o Coils shall measure 5” in height, +/-1/4”.

• Border rods must extend around the full perimeter of the unit, both top and bottom, and are to be 6-gauge high carbon spring steel.

• Helical wire must be a minimum of 17.5 gauge.

1.4.7.3.2 Physical Characteristics and Testing Methods Per industry standards.

1.4.7.3.3 Flame Resistance Characteristics and Testing Methods Per industry standards.

1.4.7.3.4 Finish and Color The mattress unit shall be a finished spring unit free of sharp edges and a natural steel color.

1.4.7.3.5 Workmanship The complete unit shall be free from any obvious manufacturing imperfections which may impair its serviceability and shall be heat treated after assembly to relieve stress.

1.4.7.3.6 Odor The complete unit shall be clean and free of any residual manufacturing lubricant or odor.

1.4.7.3.7 Size The size shall be as listed in the bid item grid.

1.4.7.4 Packaging The innerspring mattress units must be compressed and crated in bundles of 20 units and shall be packaged to meet all safety requirements.

1.4.8 CATEGORY VIII: Perm-a-lator Style Wire Spring Insulator

1.4.8.1 Intended Use The wire spring insulators required by this specification are intended to be used with the innerspring mattress units as a means of preventing the top/bottom mattress padding materials from working into the innersprings.

1.4.8.2 Material The wire spring insulators must be constructed from steel wires and paper cords.

1.4.8.2.1 The steel wires must be 20-gauge, minimum, high-carbon steel.

1.4.8.2.2 The paper cords must be a heavy paper typical for the application.

1.4.8.3 Physical Properties

1.4.8.3.1 Construction

• The insulators must be fabricated from approximately 62 individual wires, approximately 1-1/4” apart, passing widthwise through at least three lengthwise inner paper cords.

• The paper cords must be fabricated from at least six strands of paper, twisted together, forming a cord with an overall diameter of approximately 5/32”.

• A twisted paper cord must be secured to each end of each wire and each wire must pierce each of the remaining, inner cords.

• The inner cords must be spaced equally across the width of the insulator.

1.4.8.3.2 Physical Characteristics and Testing Methods Per industry standards.

1.4.8.3.3 Flame Resistance Characteristics and Testing Methods Per industry standards.

1.4.8.3.4 Finish and Color The wires must be straight and smooth, and the insulator must be the natural color of the components.

1.4.8.3.5 Workmanship The wire insulator must be constructed to present a flat, rectangular unit free of obvious defects that may affect its serviceability and must conform to industry standards.

1.4.8.3.6 Odor The insulators must be odor free.

1.4.8.3.7 Size The wire spring insulators must be 34” wide by 77-1/2” long.

1.4.8.4 Packaging The product shall be adequately packaged to provide safe transport to the using

1.4.9 CATEGORY IX: Bonded Polyester Upholstery Fiber

1.4.9.1 Intended Use The bonded polyester required by this specification is intended for the use in the fabrication of chairs for general seating applications.

1.4.9.2 Material

1.4.9.2.1 Fiber 15 Denier.

1.4.9.2.2 Resin 25% by weight.

1.4.9.2.3 Weight .75 ounces per square foot (+10%/-7%).

1.4.9.2.4 Staple Length 3”

1.4.9.3 Physical Properties

1.4.9.3.1 Construction The form of this material shall be sheets of no less than 80” in length.

1.4.9.3.2 Physical Characteristics and Testing Methods Per industry standards.

1.4.9.3.3 Flame Resistance Characteristics and Testing Methods Per industry standards.

1.4.9.3.4 Finish and Color Per industry standards.

1.4.9.3.5 Workmanship The product shall be of uniform texture and shall be free from any

1.4.9.3.6 Odor The fabric must be odor free and contain no VOCs.

1.4.9.3.7 Size The size shall be as listed in the bid item grid with no length (piece) less than

80”.

1.4.9.4 Packaging The material shall be in rolls and wrapped in plastic to provide safe transport to the using location.

1.4.10 CATEGORY X: Polyester Fabric

1.4.10.1 Intended Use The polyester fabric required by this specification is intended for the use in the fabrication of mattresses for high risk and public occupancy applications.

1.4.10.2 Material The fabric shall be a denier type fabric suitable for the intended use.

1.4.10.3 Physical Properties

1.4.10.3.1 Construction

• Thickness 10mils

• Weight 2.0 oz/sq yd, +/-0.1 oz.

1.4.10.3.2 Physical Characteristics and Testing Methods

• Tensile Strength Machine Direction: 70 pounds minimum.

• Tear Strength Machine Direction: 13.4 pounds minimum.

1.4.10.3.3 Flame Resistance Characteristics and Testing Methods Consistent with industry

1.4.10.3.4 Finish and Color The fabric shall have a consistent finish and color consistent with industry standards.

1.4.10.3.5 Workmanship The fabric shall be free from any obvious manufacturing imperfections which may impair its serviceability and shall conform to industry standards.

1.4.10.3.6 Odor The fabric shall be odor free.

1.4.10.3.7 Size The fabric size shall be as listed in the bid item grid.

1.4.10.4 Packaging The packaging is to be standard for industry. Fabric shall be rolled on cores and wrapped in poly bag or any other strong wrapping material so that the fabric is neither

1.4.11 Category XI: Clear Vinyl Fabric

1.4.11.1 Intended Use The clear vinyl fabric required by this specification is intended for the use in the fabrication of shower curtains for high risk and public occupancy applications and the fabrication of lunch and tote bags in general use applications.

1.4.11.2 Material Vinyl fabric manufactured form compounds consistent with industry standards.

1.4.11.3 Physical Properties The fabric shall be soil resistant and hypoallergenic.

1.4.11.3.1 Construction

• Thickness 20mil, minimum, per ASTM D1005.

• Weight 18 oz/sq yd, minimum, per ASTM D3776.

1.4.11.3.2 Physical Characteristics and Testing Methods The fabric shall be soil resistant and hypoallergenic.

1.4.11.3.3 Flame Resistance Characteristics and Testing Methods The fabric shall be smolder resistant and meet the requirements of both NFPA 701 and California Technical Bulletin 117, achieving a passing rating.

1.4.11.3.4 Finish and Color The fabric shall be clear, having a uniform, smooth finish.

1.4.11.3.5 Workmanship The fabric shall be free from any obvious manufacturing imperfections which may impair its serviceability and shall conform to industry standards.

1.4.11.3.6 Odor The fabric shall be odor free and self-deodorizing.

1.4.11.3.7 Size The fabric size shall be as listed in the bid item grid with a width tolerance of (+)

1.5” for an acceptable width between 36.5” to 38”.

1.4.11.4 Packaging The packaging is to be standard for industry. Fabric shall be rolled on cores and wrapped in poly bag or any other strong wrapping material so that the fabric is neither

1.4.12 Category XII: Scrim Based Vinyl Fabrics and Adhesive

1.4.12.1 Intended Use The scrim-based vinyl fabric and adhesive required by this specification is intended for use as mattress coverings in the fabrication of industrial/ health mattresses for high risk and public occupancy applications.

1.4.12.2 Material The heavy-duty fabric shall be equivalent to polyester reinforced polyvinyl chloride plastic fabric laminated on both sides with a plasticized vinyl chloride polymer coating; clear or pigmented so as to meet the requirements specified herein.

1.4.12.3 Physical Properties

1.4.12.3.1 Construction

• Base Cloth The base cloth shall be a 6 x 6 (minimum) 1000D woven polyester scrim. The size of yarn and construction of the cloth shall be as is necessary to provide overall coated weight and to conform to the other physical properties.

• Coating The coatings shall be resistant to staining from various hospital medicants, excreta and soil. Material shall be cleanable with a cloth or sponge using mild soap and water, leaving a clean, unbleached surface after washing.

The coating shall be free of objectionable odors and free from ingredients which may have an irritating effect on the skin or are known to be toxic.

• Weight o Clear Scrim Based Vinyl Fabric 11oz, +/- 1oz.

o Pigmented Scrim Based Vinyl Fabric

▪ Mattress Covering 14oz, +/- 1oz,

▪ Pillow Covering 11.5 - 12oz.

1.4.12.3.2 Physical Characteristics and Testing Methods The material shall comply with the following standards.

• Workability The fabrics shall be capable of being sewn and cemented and shall be capable of being patched, seamed, or similarly repaired with a cement to be specified by the awarded contractor.

• Compatibility The fabric shall be compatible with HR foam, neoprene foam, thermally bonded polyester foam, boric acid treated cotton batting, and other mattress core materials listed herein.

• Pliability To assure the occupant’s comfort the fabric shall have excellent pliability, softness to hand and conform to industry standards.

• Crease Resistance The fabric shall be crease resistant when folded and refolded repeatedly, showing no sign of cracking, or flaking.

• Durability The fabric shall be extremely strong and resistant, not suffering cracks or showing damaging effects under typical institutional use and cleaning for a minimum of two (2) years.

• Electrostatic Charge Dissipation Antistatic hospital fabrics shall be capable of preventing the accumulation or dangerous amounts of static electrical charges.

It shall prevent build up or retention of dangerous electrostatic charges. It must be an integral part of the fabric which cannot be worn away.

• Antimicrobial o The fabric shall be resistant to antimicrobial activity and resistant to organisms that degrade, stain, or leave odors.

o The fabric shall be hypoallergenic and free of toxic reactions or irritation to patient exposure.

o The fabric shall meet all federal requirements regarding antimicrobial activity and patient exposure.

o The fabric shall be bacteriostatic.

• Stain and Penetration Resistance o The fabric shall be alcohol resistant and there shall be no discoloration or other adverse effects.

o The fabric shall be oil resistant without staining, discoloration or penetration and the tear strength shall not be significantly affected.

o The fabric shall be fluid proof and bacterial and fungal resistant.

1.4.12.3.3 Flame Resistance Characteristics and Testing Methods The material shall comply with the following standards.

EPA Registration #’s 2829 -143 Free of Heavy Metals and Arsenicals

Activity Reduction % Staph Aureus (Gram +) Kleb. Pneumoniae (Gram -)

AATCC Method 147 Pass > 1 mm Inhibition > 1 mm Inhibition

Flame Resistance ASTM D6413 Afterflame W – 0.4 , F – 0.8 Char Length W – 4.3 , F – 4.4 Pass

NFPA 701

Cal. Tech Bulletin 117

Pass Pass

Cigarette Ignition 16 CFR, Part 1632 & Class A Barrier

As Specified

Liquid Penetration, psi ASTM D751 F-220, R-220

Adhesion lbs/2” ASTM D751 32

Tear Strength ASTM D2261 W-70 F-60

Breaking Strength ASTM D5034 W-135 F-132

Surface Resistivity NFPA 99, Para 3-3.6.2.7 Anti-Static

Weight (oz,/sq/yd) ASTM D3776 As Specified

1.4.12.3.4 Finish and Color The exterior (exposed) surface of the fabric should have a non-skid plain weave finish to minimize patient, mattress, or bed linen slippage.

• Clear Scrim Based Vinyl Fabric Glass clear, increasing safety and security to staff and inmate population by making it difficult to impossible to conceal contraband and weapons.

• Pigmented Scrim Based Vinyl Fabric Fawn and blue are the two standard colors and shall be colorfast: permanent, non-fading and non-bleeding.

1.4.12.3.5 Workmanship

1.4.12.3.6 Odor The fabric shall be odor free and self-deodorizing.

1.4.12.3.7 Size The fabric size shall be as listed in the bid item grid with a tolerance of (+) 2.”

1.4.12.4 Packaging The fabrics shall be furnished in rolls on a skid, shrink wrapped, and packed in accordance with good commercial practice.

1.4.12.4.1 No more than two (2) lengths (pieces) per roll, with no length (piece) less than seven

(7) yards long.

1.4.12.4.2 Each roll wrapper shall be marked with the name of the manufacturer and their identifying stock or serial number.

1.5 WARRANTY The Contractor(s) shall provide a warranty on all products against manufacturing defects for a period of at least five years from the date of the final customer’s acceptance. Should a defect occur, the contractor shall repair or replace item(s) at no charge to the State of Ohio.

1.6 QUALITY ASSURANCE

1.6.1 The Contractor(s) may be required to submit laboratory test report(s) throughout the duration of any contract issued pursuant to this ITB for any test specified herein from an Independent Certified Laboratory showing the test results of the supplies being offered. The test report(s) will be used to evaluate the product being received to assure it complies with the contract requirements. If not included with product shipment(s), the Contractor will be required to provide the test report(s) within thirty (30) calendar days after notification by the ordering agency or DAS. Failure of the Contractor to provide the Independent Certified Laboratory test report(s) within the stated time period may result in the Contractor being found in contract default. The cost of the requested test report(s) shall be paid entirely by the Contractor(s).

1.6.2 Throughout the duration of any contract issued pursuant to this ITB, the Contractor(s) may be required to provide one sample to the State for visual inspection and approval prior to laboratory testing within 14 calendar days after notification. Sample dimensions may vary for testing purposes and may be from any category included in the contract.

2 - STANDARD TERMS AND CONDITIONS

State of Ohio Standard Terms and Conditions (revised 03/01/24) will apply to this Contract.

3 - CONTRACT SPECIFIC TERMS AND CONDITIONS

3.1. ORDER OF PRIORITY The order of priority of the Contract will be the following: 1.) Specifications and

Requirements; 2) Contract Specific Terms and Conditions; 3) Standard Terms and Conditions.

3.2. AMENDMENT TO CONTRACT TERMS AND CONDITIONS The following Amendments to the Contract Terms and Conditions do hereby become a part hereof. In the event that an amendment conflicts with the Contract Terms and Conditions, the Amendment will prevail.

https://gcc02.safelinks.protection.outlook.com/?url=https%3A%2F%2Fprocure.ohio.gov%2Fstatic%2FTCond%2FStandard_T_C%25203-1-24.pdf&data=05%7C02%7CLloyd.Harmon%40das.ohio.gov%7Cff0f09d10a8c49785c4708dc3a0e53f9%7C50f8fcc494d84f0784eb36ed57c7c8a2%7C0%7C0%7C638449080432433241%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C0%7C%7C%7C&sdata=uta1Ms5rhEnWVQBR7oZR1gSTUXz5bfIFUTqfJNjvlBE%3D&reserved=0

3.3. SPECIAL CHARGES No assessment, surcharge, small order charge, broken case charge, minimum order charge, single item charge nor any other unspecified additional charge is allowed by the State that is not specifically mentioned in this Contract.

3.4. MINIMUM ORDER The minimum dollar value of any order placed against this Contract for delivery F.O.B.

destination, transportation charges prepaid, at any one time to one destination, shall not be less than indicated as Bidder’s minimum order value in the questionnaire submitted at the time of bid. The Contractor’s minimum order value shall be firm for the life of the Contract. Failure to provide or state a minimum order value at the time of bid shall be interpreted as no minimum order applies to any order.

For orders with a total value less than the Contractor’s established minimum, shipment is to be made by freight, parcel post, express or commercial package delivery, whichever is the most economical method for proper delivery of the item, F.O.B. destination. The cost of transportation from the Contractor's address to the destination on such orders shall be prepaid and added to the invoice.

Bidders may also indicate a minimum order quantity per item or category of materials in the questionnaire submitted at the time of bid.

3.5. DELIVERY Supplies will be delivered to the participating agency within 30 days after receipt of order. The delivery location will be noted on the purchase order issued by the participating agency.

3.5.1 The current delivery location is:

The Ohio Department of Rehabilitation and Correction Ohio Penal Industries, Chillicothe Correctional Institution

15802 State Route 104 North Chillicothe, OH 45601

3.5.2 SECURITY CONSIDERATIONS The delivery location is an operational correctional facility where security conditions could create abnormal delays or rejection of shipment(s). These conditions could include, but are not limited to, emergency lockdowns, fog alerts and other inclement weather or events. The Contractor shall cooperate in good faith and not interfere with the operations of the institution.

3.5.3 Deliveries will be accepted from 8:00am to 10:00am and 12:00pm to 2:00pm, Monday through Friday, excluding State observed holidays. The carrier is to call the OPI Shop at the institution prior to arrival for authorization to deliver. No deliveries will be accepted during foggy or adverse weather conditions in accordance with institution security procedures. All damaged items received shall be noted on the driver’s Bill of Lading, placed back on the truck, and returned to the contractor for prompt replacement. In the event a problem cannot be resolved with the institution shop manager, contact OPI Production Manager (CIM3) at OPI-Central Office, 1580 State Route 56 SW, PO Box 525 London OH 43140, phone (614) 738-7859.

3.6 FIXED PRICE WITH ECONOMIC ADJUSTMENT The contract prices(s) will remain firm for the first 12 month duration of the contract. Thereafter, the Contractor may submit a request to increase their price(s) to be effective 30 calendar days after acceptance by DAS. No price adjustment will be permitted prior to the effective date of the increase received by the Contractor from its suppliers, or on purchase orders that are already being processed, or on purchase orders that have been filled and are awaiting shipment. If the Contractor receives orders requiring quarterly delivery, the increase will apply to all deliveries made after the effective date of the price increase.

The price increase must be supported by a general price increase in the cost, due to increases in the cost of raw materials, labor, freight, Workers' Compensation and/or Unemployment Insurance, etc. Detailed documentation, to include a comparison list of the contract items and proposed price increases, must be submitted to support the requested increase. Supportive documentation should include, but is not limited to: copies of the old and the current price lists or similar documents which indicate the original base cost of the product to the Contractor and the corresponding increase, and/or copies of correspondence sent by the Contractor's supplier on the supplier's letterhead, which contain the above price information and explains the source of the increase in such areas as raw materials, freight, fuel or labor, etc.

Should there be a decrease in the cost of the finished product due to a general decline in the market or some other factor, the Contractor is responsible to notify DAS immediately. The price decrease adjustment will be incorporated into the contract and will be effective on all purchase orders issued after the effective date of the decrease. If the price decrease is a temporary decrease, such should be noted on the invoice.

In the event that the temporary decrease is revoked, the contract pricing will be returned to the pricing in effect prior to the temporary decrease. For quarterly deliveries, any decrease will be applied to deliveries made after the effective date of the decrease. Failure to comply with this provision will be considered as a default and will be subject to the “Suspension/Termination” and the “Contract Remedies” sections of the “Standard Contract Terms and Conditions”.

3.7 MANUFACTURER, MANUFACTURER’S REPRESENTATIVE, OR AUTHORIZED DISTRIBUTOR

Bidders responding to this ITB must be authorized distributors, manufacturers, or representatives of manufacturers of the items bid. Bidders may be required to submit proof of the above. If requested, Bidders will have seven days to provide proof of the relationship. If requested Bidders shall submit certification attesting that they are the manufacturer or an authorized distributor, or manufacturer’s representative of the products being bid. This certification must be on the manufacturer’s letterhead, signed by a duly authorized employee of the manufacturer.

3.8 SUBSTITUTION OF ITEMS During the term of the Contract, the Contractor may have a need to substitute alternate manufacturer brand/style/items other than those agreed to under the Contract. Prior to the provision of any alternate however, the Contractor must notify DAS in writing and obtain written permission from the DAS Office of Procurement Services for use of any alternate item(s). DAS may require samples prior to the approval of any alternate item(s). Failure to comply with this clause shall be considered a material default.

4 - INVITATION TO BID INSTRUCTIONS

Instructions, Terms and Conditions for Bidding that apply to the solicitation.

5 - SPECIAL INSTRUCTIONS TO BIDDERS

5.1. EVALUATION Bids will be evaluated in accordance with Article I-15 of the “Instructions to Bidders”. In addition, the state will multiply the bid price by the estimated annual usage as listed in the item grid for each line item and add these products together to arrive at a total for each category. Failure to bid all required items within an identified category may result in the bidder being deemed as not responsive for that category. Optional items are not a part of the evaluation.

5.2. CONTRACT AWARD The contract will be awarded to the lowest responsive and responsible bidder by category of product. Failure to bid all required items within an identified category may result in the bidder being deemed not responsive for that category.

5.3. OPTIONAL ITEMS Some categories of material include optional items. These optional items are noted as such in the item grid. Bidders submitting bids for these categories may also submit bids for these optional items. Optional items will not be used for evaluation purposes.

5.4. DESCRIPTIVE LITERATURE The Bidder may be required to submit descriptive literature of the supplies or services being offered. If requested, the literature will be used in the evaluation process to determine the lowest responsive and responsible bidder. If not provided as part of the bid response, the Bidder must provide said literature within seven calendar days after request/notification by the Office of Procurement Services to do so. Failure of the Bidder to furnish descriptive literature either as part of their bid response or within the time specified herein will deem the bidder not responsive.

5.5. LABORATORY TEST RESULTS The Bidder may be required to submit laboratory test reports from an independent certified laboratory for the supplies being offered. If requested, the test results will be used in the evaluation process to determine the lowest responsive and responsible bidder. If not provided as part of the bid response, the Bidder must provide said test results within seven calendar days after request/notification by the Office of Procurement Services to do so. Failure of the Bidder to furnish test results either as part of their bid response or within the time specified herein will deem the bidder not responsive.

5.6. PRODUCT SAMPLES The bidder(s) may be required to submit samples of the supplies being offered.

The samples will be used in the evaluation process to determine the lowest responsive and responsible bidder. If not included as part of their bid response, the bidder will be required to provide the samples within seven calendar days after notification. Failure to provide the samples within the stated time period will result in the bidder being deemed not responsive. After award of the contract, the samples will be used as a basis of comparison with actual product delivered under contract. Any variation between the samples and product being delivered will be considered as an event of default. Any variations between the samples and actual product being delivered that are due to manufacturer changes may be acceptable and shall require prior written approval from DAS.

https://procure.ohio.gov/pdf/OhioBuys_ITB_Instructions_to_Bidders_030921.pdf

5.7. SITE VISIT A site visit will be held on Monday 04/01/24 at Chillicothe Correctional Institution 15802 State Route 104 North Chillicothe, OH 45601 to survey the facility and discuss the requirements of the solicitation. The site visit will commence promptly at 10:00 AM, barring an unforeseen circumstance that results in a delay of the site visit. Attendance will be taken. The state will not be responsible to a supplier for their failure to obtain information discussed during the site visit due to their failure to attend and/or arriving after the site visit has convened.

Please contact Lloyd Harmon no later than 3:00 pm on Thursday 03/28/24 at lloydharmon@das.ohio.gov during regular business hours to make arrangements for authorization to enter the facility.

mailto:lloydharmon@das.ohio.gov