Special Packaging Instructions AK12076375.pdf
PDF 150 KB Posted
- Attached to
- Cylinder Assembly, Actuating, Linear
- Solicitation number
- SPRDL1-26-R-0012
About this file
This is a DD Form 2169 Special Packaging Instruction document dated 8 DEC 2025 (Revision D) for a cylinder component (Part No. 6-372-002210, National Stock No. 3040-01-2076375). The document specifies detailed preservation, packing, and shipping requirements for a 19207 cylinder manufactured by Weatheris. The item weighs 300.0 pounds and measures 048.0 x 014.2 x 014.0 inches in unit pack configuration. The shipping container dimensions are 45 x 12-1/2 x 9-3/4 inches, constructed using 1-inch nominal lumber with 2-inch nominal ends.
Packaging specifications require internal preservation using the manufacturer's recommended lubricant with cylinder rods fully retracted, followed by sealing all openings with NAS847 caps/plugs. Bare metallic surfaces must be treated with MIL-PRF-16173, Grade 4 preservative, and the item wrapped with MIL-PRF-121, Type I wrap secured with tape to prevent contact with the container. Quality assurance and preservation inspection must comply with MIL-STD-2073-1, Method 20. Blocking and bracing per ASTM-D6199 is specified with detailed lumber dimensions (A through G components ranging from 2x2-3/4x12-1/2 to 2x10x11). Marking requirements reference MIL-STD-129, and the unit container serves as the shipping container per note G. Page 2 contains a technical diagram illustrating the top and side views of the packed configuration with labeled blocking and bracing placements.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS.
FORM APPROVED
OMB No. 0704-0188
3040-01-2076375 8 DEC 2025
AK12076375
D
4. NATIONAL STOCK NO.
2. CAGE 3. SPI NO.
6. REVISION5. DATE
1. PART OR DRAWING NO. (CAGE) NOMENCLATURE
-SW
WEATHERIS
SPECIAL PACKAGING INSTRUCTION
6-372-002210 (12361) CYLINDER 19207
A. QUALITY ASSURANCE PROVISIONS, PRESERVATION: INSPECT THE PRESERVATION AND UNIT PACK IN
ACCORDANCE WITH MIL-STD-2073-1.
B. PRESERVATIVE: WITH CYLINDER RODS FULLY RETRACTED, PRESERVE INTERNALLY USING MANUFACTURER'S
RECOMMENDED LUBRICANT. THOUROUGHLY DRAIN EXCESS.
C. CAPS/PLUGS: SEAL ALL OPENINGS WITH CAPS/PLUGS OF THE APPROPRIATE SIZE.
D. PRESERVATIVE: APPLY TO BARE, UNPLATED, UNPAINTED METALLIC SURFACES.
E. WRAP: WRAP ITEM WITH WRAP AND SECURE WITH TAPE TO PREVENT ITEM CONTACT WITH CONTAINER.
F. CONTAINER: CONSTRUCT USING 1" NOMINAL LUMBER WITH 2" NOMINAL ENDS AND NO END CLEATS REQUIRED.
G. PACKING: THE UNIT CONTAINER IS THE SHIPPING CONTAINER.
001 NONE 0300.0 0005.522
MIL-STD-2073-1, METHOD 20
MIL-STD-2073-1
MIL-STD-2073-1
10. UNIT PACK CU. (CU. FT.) 11. UNIT PACK SIZE (IN)
12. MILITARY PRESERVATION
17. NOTES / DRAWING
15. PACKING
14. DRYING
13. CLEANING
7. QUP 8. ICQ 9. UNIT PACK WT. (LB)
20.
DESCRIPTION
18.
STEPS
19.
REQ'D
MIL-STD-2073-1 AND NOTE G
NOT APPLICABLE
MIL-STD-129
048.0 014.2 014.0X X
b. LEVEL B
16. MARKING
a. LEVEL A
1B 2C 3D 4E
6F
A/R A/R A/R
A/R A/R
PRESERVATIVE: SEE NOTES
CAPS/PLUGS: NAS847
PRESERVATIVE: MIL-PRF-16173, GR 4
WRAP: MIL-PRF-121, TY I, AS REQUIRED
BLOCKING AND BRACING: ASTM-D6199, SEE PG 2
CONTAINER: ASTM-D6880, ST 4, CL 2,
SIZE: 45 X 12-1/2 X 9-3/4
DD FORM 2169, JUN 1997 PREVIOUS EDITIONS ARE OBSOLETE Page 1 of 2 Pages
The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS.
FORM APPROVED
OMB No. 0704-0188
3040-01-2076375 02/25/09
AK12076375
C
4. NATIONAL STOCK NO.
2. CAGE 3. SPI NO.
6. REVISION5. DATE
-SW
WEATHERIS
SPECIAL PACKAGING INSTRUCTION (Continuation Sheet)
1. PART OR DRAWING NO. (CAGE) NOMENCLATURE
6-372-002210 (12361) CYLINDER 19207
DD FORM 2169, JUN 1997 PREVIOUS EDITIONS ARE OBSOLETE Page 2 of 2 Pages
File details come from the government source that posted it. Updated .