SPRBL1-21-R-0013 (G2S) Exhibit D - SPI-AG00000601C (2021-08-18).pdf

SPECIAL PACKAGING INSTRUCTION

Form Approved

OMB No. 0704-0188

1. PART OR DRAWING NO.

Circuit Card and Printed Circuit Board

Assemblies

2. CODE IDENT

80063

3. SPI NO.

AG00000601

4. NATIONAL STOCK NO

MULTIPLE NSNs

5. DATE OF DRAWING

15116

6. REVISION

C

7. QUP

8. ICQ

NONE

9.UNIT PACK WEIGHT 10.UNIT PACK CUBE 11.UNIT PACK SIZE

12. PRESERVATION 18.

STEPS

19.

REQD

20.

DESCRIPTION

MILITARY

NOTE 1

N/A N/A N/A

13. CLEANING

MIL-STD-2073-1

APPLICABLE DOCUMENTS

DDSFSDFDF

14. DRYING

MIL-STD-2073-1

MIL-STD-129

MIL-STD-147

MIL-STD-2073-1

MIL-PRF-121

MIL-DTL-117

MIL-DTL-81997

PPP-B-1672

ASTM D 5330

ASTM D 5486

ISPM 15

ASME MH1

15. PACKING

a. LEVEL A

MIL-STD-2073-1

b. LEVEL B

MIL-STD-2073-1

16. MARKING

MIL-STD-129 AND FIGURE 1

17. NOTES/DRAWINGS

1. PRESERVATION. In accordance with MIL-STD-2073-1, as specified herein, ensuring compliance with the applicable requirements of that standard.

1.1 Military.

1.1.1 Electrostatic sensitive assemblies. Unit pack each assembly using the specialized preservation code “GX” as follows: Wrap or cushion with antistatic materials (as required). Place item within a bag conforming to

MIL-DTL-117, Type I, Class F, Style 1. Heat seal bag. Reclosable cushioned pouches conforming to MIL-DTL-81997, Type I or II, may be used in lieu of initial wrap or cushioning. Place a MIL-STD-129 electrostatic discharge (ESD) sensitive devices attention label (Figure 1) on the unit pack. Place the unit pack into a container conforming to PPP-B-1672, Type II (see Table I).

Close the container by securing both ends with tape conforming to ASTM D5330 and seal all openings with tape conforming to ASTM D5486, Type V. Place a

MIL-STD-129 ESD sensitive devices attention label (Figure 1) on the box.

1.1.2 Non-ESD sensitive assemblies. Unit pack each assembly using Method 41, as follows: Wrap with barrier material conforming to MIL-PRF-121, Type I.

Place the item into a bag conforming to MIL-DTL-117, Type I or IV, Class E, Style 1. Heat seal bag. Place bagged item into a cushioned box conforming to PPP-B-1672, Type II. Close the container by securing both ends with tape conforming to ASTM D5330 and seal all openings with tape conforming to ASTM D

5486, Type V.

DA FORM 2169, JUN 86

DA FORM 2169C, JUN 86 Page 2 of 4

(Continuation Sheet )

3. SPI NO.

AG00000601

6. REVISION

C

1.2 Unitization. Palletization shall be required when quantities per destination exceed either a total of 250 pounds (excluding the pallet) or a volume of 20 cubic feet. A quantity of items, packed for shipment, shall be placed on pallets, standard size 40 x 48 inches, 4-way entry, conforming to

ASME MH1, Class 1 or 2, Type 3, any Style, or Part 9 of the document, Size 2

(40 x 48 inches). The load shall be “bonded” to the pallet by any means that will ensure safe delivery to destination. MIL-STD-147 covers the methods, materials, and techniques to be employed in the formation of bonded palletized unit loads of military supplies.

2. REQUIREMENTS FOR WOOD PACKAGING MATERIAL. All CONUS and OCONUS shipments utilizing wood packaging material, such as pallets, dunnage, crating, packing blocks, drums, cases, load boards, pallet collars, and skids, shall meet the

International Standards for Phytosanitary Measures, ISPM 15, entitled

“Regulation of Wood Packaging Material in International Trade”.

DA FORM 2169C, JUN 86 Page 3 of 4

3. SPI NO.

AG00000601

TABLE I. FAST PACK SELECTION

This table is intended only as an aid to container selection and does not eliminate any testing or approval requirements. Containers are in accordance with PPP-B-1672. A listing of fast pack containers with NSNs and Pack Codes is also provided in MIL-STD-2073-1, Table C-

IV.

MAXIMUM BARE

ITEM DIMENSIONS

MAXIMUM

BARE WEIGHT

CONTAINER INSIDE

DIMENSIONS

CNTR

CODE

CNTR

WEIGHT

CNTR OUTSIDE

DIMENSIONAL DATA

L W D CUBE

Type I

3 x 3 x 6 4.00 6 x 6 x 10 NR 1.4 6.3 6.3 10.5 0.242

4x 4 x 8 8.50 8 x 8 x 12 NR 2.4 8.3 8.3 12.5 0.499

5 x 5 x 6 9.00 10 x 10 x 12 NR 3.2 10.5 10.5 12.5 0.798

6 x 6 x 8 12.00 12 x 12 x 14 NR 4.8 12.5 12.5 14.5 1.312

6 x 6 x 10 20.00 12 x 12 x 18 NR 5.3 12.5 12.5 18.5 1.673

7 x 7 x 10 23.00 14 x 14 x 16 NR 7.5 14.5 14.5 16.5 2.008

Type II

5 x 4-1/2 x 1-1/4 0.50 6 x 5 x 2-1/2 NS 0.3 6.3 5.3 3.0 0.058

5 x 4-1/2 x 2-1/4 1.00 6 x 5x3-1/2 NS 0.4 6.3 5.3 4.0 0.078

8 x 5-1/2 x 1-1/4 0.90 9 x 6x2-1/2 NS 0.6 9.3 6.3 3.0 0.102

8 x 5-1/2 x 2-1/4 1.80 9 x 6x3-1/2 NS 0.7 9.3 6.3 4.0 0.136

9 x 9-1/2 x 2-1/4 1.80 10 x 10x3-1/2 NS 1.0 10.5 10.5 4.0 0.256

11 x 7-1/2 x 1-1/4 1.80 12 x 8 x 2-1/2 NS 0.8 12.5 8.3 3.0 0.181

11 x 7-1/2 x 2-1/4 3.60 12 x 8 x 3-1/2 NS 0.9 12.5 8.3 4.0 0.241

12 x 12-1/2 x 2-1/4 4.30 13 x 13 x 3-1/2 NS 1.5 13.5 13.5 4.0 0.422

15 x 15-1/2 x 2-1/4 8.60 16 x 16 x 3-1/2 NS 2.0 16.5 16.5 4.0 0.631

17 x 11-1/2 x 1-1/4 4.30 18 x 12 x 2-1/2 NS 2.8 18.5 12.5 3.0 0.402

17 x 11-1/2 x 2-1/4 8.60 18 x 12 x 3-1/2 NS 2.9 18.5 12.5 4.0 0.536

23 x 15 x 2-1/4 10.00 24 x 16 x 3-1/2 NS 3.5 24.5 16.5 4.0 0.936

Type III

24 x 11 x 9 54.00 30 x 16 x 14 NV 13.0 31.0 17.0 14.5 4.423

26 x 6 x 8 30.00 32 x 12 x 14 NV 11.0 33.0 13.0 14.5 3.600

20 x 5 x 5 20.00 26 x 9 x 9 NV 5.5 27.0 10.0 9.3 1.454

18 x 8 x 8 38.00 24 x 14 x 14 NV 9.5 25.0 15.0 14.5 3.147

16 x 10 x 5 8.00 20 x 14 x 9 NV 4.3 21.0 15.0 9.5 1.732

13 x 7 x 7 19.00 25 x 14 x 14 NV 8.0 26.0 15.0 14.5 3.273

24 x 13 x 11 80.00 32 x 18 x 16 NV 22.0 32.5 18.5 17.0 5.916

25 x 18 x 12 90.00 34 x 24 x 18 NV 27.0 36.5 26.5 19.0 10.636

18 x 13 x 11 50.00 24 x 18 x 16 NV 14.0 25.0 19.0 16.5 4.536

24 x 21 x 8 50.00 30 x 27 x 14 NV 18.0 31.0 28.0 15.0 7.535

Type IV 14 x 7 x 7 29.00 20 x 14 x 14 NW 8.4 20.5 14.5 14.5 2.495

16 x 7-1/4 x 7-1/4 31.00 22 x 16 x 16 NW 9.5 22.5 16.5 16.5 3.545

NR = Vertical Star (Type I) NS = Folding Convoluted (Type II)

NV = Encapsulated (Type III) NW = Horizontal Star (Type IV)

DA FORM 2169C, JUN 86 Page 4 of 4

3. SPI NO.

AG00000601