patternwmnjump.txt

JUMPER, WOMAN'S, WHITE

ADDITIONAL INFORMATION FOR MIL-J-24949:

PATTERN DATE: 10 APRIL 2008

CLOTH, TWILL, POLYESTER, WHITE SHADE NO. 3006,

PIECE NO. 06020.

INTERIM CHANGES TO MIL-J-24949:

PAGE 1, PARA. 1.2, UNDER LENGTH, ADD AT THE END "X-TALL (X-LONG)) - XT"

PAGES 1 AND 2, PARA. 1.2, DELETE SIZE SCHEDULE AND SUBSTITUTE:

SCHEDULE OF SIZES

MISSES (M), JUNIORS (J), AND WOMEN (W)

PETITE (P) REGULAR (R) TALL (T) X-TALL (XT)

4 4 4 4 6 6 6 6 8 8 8 8 10 10 10 10 12 12 12 12 14 14 14 14 16 16 16 16 18 18 18 18 20 20 20 20 22 22 22 22 24 24 24 24 26 26 26 26 28 28 28 28

PAGE 2, PARA. 2.1.1, UNDER SPECIFICATIONS, FEDERAL, DELETE "V-T-276" AND

SUBSTITUTE "A-A-52094". UNDER SPECIFICATIONS, FEDERAL, DELETE "V-T-

280" AND SUBSTITUTE "A-A-50198".

ADD NEW ENTRIES. "A-A-50199 - THREAD, POLYESTER, CORE, COTTON-OR-

POLYESTER-COVERED"

PAGE 3, PARA. 2.1.1, UNDER SPECIFICATIONS, MILITARY, DELETE ENTRY FOR

"MIL-T-43548" IN ITS ENTIRETY. UNDER STANDARDS, MILITARY, ADD THE

FOLLOWING: "MIL-STD-984 - PROVISIONS FOR SIZE LABELILNG FOR WOMEN'S

UNIFORM CLOTHING". AT THE END, ADD NEW ENTRY:

"DRAWINGS

NAVY CLOTHING AND TEXTILES RESEARCH FACILITY

16-1-872 - CROWTACKS FOR JUMPERS

(COPIES OF THIS DRAWING ARE AVAILABLE FROM THE PROCURING

AGENCY.)".

PAGE 5, PARA. 3.3.3.1, LINE 4, DELETE "MIL-T-43548" AND SUBSTITUTE "A-A-

50199". PARA. 3.3.3.1.1, LINE 3, DELETE "V-T-276" AND SUBSTITUTE "A-A-

52094". LINE 5, DELETE "MIL-T-43548" AND SUBSTITUTE "A-A-50199".

PAGE 5, PARA. 3.3.3.2, LINE 3, DELETE "V-T-276 OR MIL-T-43548" AND

SUBSTITUTE "A-A-52094 OR A-A-50199". LINE 4, DELETE "V-T-276" AND

SUBSTITUTE "A-A-52094". LINE 5, DELETE "MIL-T-43548" AND SUBSTITUTE "A-

A-50199".

PAGE 5, PARA. 3.3.5, LINE 4, DELETE "V-T-280" AND SUBSTITUTE

"A-A-50198". PARA. 3.3.5.1, LINE 5, DELETE "V-T-280" AND SUBSTITUTE "A-

A-50198"

PAGE 6, PARA. 3.3.6, LINE 20, DELETE "FOLLOW NAVEDTRA MANUAL

414-01-45-81, FORMULA II" AND SUBSTITUTE "FOLLOW SHIPBOARD

WASH FORMULA I". PARA. 3.3.6.1, DELETE IN ITS ENTIRETY AND SUBSTITUTE:

"3.3.6.1 SIZE LABEL. EACH JUMPER SHALL HAVE A

SEPARATE SIZE LABEL CONFORMIONG TO TYPE IV OR VI, CLASS 2 OF

MIL-DTL-32075 AND THE BODY DIMENSIONS LABELING REQUIREMENTS

CONFORMING TO MIL-STD-984. THE LABEL SHALL INDICATE SIZE, BODY

DIMENSIONS AND NATIONAL STOCK NUMBER AS SHOWN BELOW:

SIZE CODE: 12 JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38

HEIGHT: LESS THAN 63-1/2 (P) (EXAMPLE)

STOCK NO: 8405-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR APPLICABLE BODY TYPE SHALL BE "J" FOR

JUNIORS AND "W" FOR WOMEN'S. (THERE IS NO DESIGNATION FOR MISSES BODY

TYPE.). ABBREVIATIONS FOR APPLICABLE LENGTH SHALL BE "P" FOR PETITE,

"R" FOR REGULAR, AND "T" FOR "TALL."

PAGE 6, PARA 3.3.6.2, DELETE IN ITS ENTIRETY AND SUBSTITUTE:

"3.3.6.2 REMOVABLE SIZE TICKET. EACH JUMPER SHALL HAVE A

COMMERCIAL TYPE SIZE AND BODY DIMENSION TICKET ATTACHED TO THE OUTSIDE

OF THE LOWER LEFT SLEEVE. THE TICKET SHALL BE 1-1/2

INCHES LONG AND 2 INCHES HIGH, MADE OF A SUITABLE PLAIN

WEAVE CARDBOARD. THE CORNERS OF THE TICKET MAY BE DOUBLE

PERFORATED FOR EASE IN TACKING. THE TICKET SHALL BE PRINTED OR STAMPED

IN BLUE OR BLACK INK AND SHALL INCLUDE INFORMATION ON

SIZE (INCLUDING BODY TYPES AND LENGTHS" AND BODY DIMENSIONS

AS STATED IN 3.3.6.1". AFTER 3.3.62., ADD NEW PARAGRAPH:

"3.3.6.3 BAR CODE LABEL. EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH

A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS

SHALL BE A STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS

WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING.

THE TAGS SHALL HAVE A HOLE AND BE ATTACHED TO EACH ITEM BY A FASTENER,

CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODE ELEMENT SHALL BE

A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A TWELVE DIGIT

UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT.

THE INITIALS "UPC" SHALL APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN

AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT

THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND OR

PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO

THE ITEM". PARA. 3.4, LINE 3, AFTER "PIECE SLEEVES AND" INSERT "EITHER

UNHEMMED OR".

PAGE 7, PARA. 3.5.1, DELETE PATTERN PARTS LIST AND SUBSTITIUTE:

"MATERIAL CAD PATTERN CUTS

NAME NOMENCLATURE PARTS

CLOTH, BACK BACK 1

POLYESTER FRONT FRONT 1

IN-PKT INSIDE POCKET (RIGHT FRONT) 1

OUT-PKT OUTSIDE POCKET (LEFT FRONT) 1

PKT-WLT POCKET WELT 2

SLEEVE SLEEVE 2

UND-COL UNDER COLLAR 1

TOP-COL TOP COLLAR 1"

PAGE 10, TABLE I, OPERATION 4.G., LINE 8. AFTER "VERTICALLY," ADD "THE

THREE RAYS SHALL BE EQUAL IN LENGTH. THE CROWTACK STITCHING SHALL BE

EXECUTED IN ACCORDANCE WITH STITCH ENLARGEMENT NUMBER 16-1-872 AND SHALL

COMPLETELY COVER THE PRESECRIBED AREA IN A CLOSE, DENSE AND TIGHTLY

DRAWN WITH NO BACKGROUND CLOTH VISIBLE. THE RAISED AREA OF THE DESIGN

SHALL BE EQUAL TO THE REFERENCE SAMPLE. UNDER "STITCH/IN", DELETE

"126 PER CROWTACK" AND SUBSTITUTE "SEE S.E. NUMBER 16-1-872".

PAGE 12, TABLE I, OPERATION, 5.J., UNDER STITCH/INI", DELETE "126 PER

CROWTACK" AND SUBSTITUTE "SEE S.E. NUMBER 16-1-872".

PAGE 13, TABLE I, OPERATION 7.D., LINE 6, "THE TURNING POINT OF THE "V"

OPENING TOPSTITCHING SHALL EXTEND TO NO MORE THAN 1/4 INCH BELOW THE

"V" OPENING.".

PAGE 14, AFTER TABLE I, OPERATION 8.D., ADD NEW ENTRY:

"OR

E. LEAVE BOTTOM OF SLEEVE UNHEMMED AND OVEREDGE THE RAW EDGE. NOTE:

OPERATION 8.D. SHAL LBE USED WHEN JUMPERS ARE TO BE SOLD AT THE NEX

STORES AND OPERATION 8.D. SHALL BE USED FOR JUMPERS TO THE RTC GREAT

LAKES FOR RECRUIT ISSUE.". OPERATION 7.F., DELETE AND SUBSTITUTE:

"F. MAKE UNIFORM CROWTACK WITH 3 POINTED RAYS AT THE BASE OF THE "V"

NECK OPENING WITH 1/16 INCH BELOW THE "V" OPENING. THE CROWTACK SHALL

MEASURE 3/4 (+/- 1/16) INCH BETWEEN TIPS OF THE TWO OPPOSITE RAYS. THE

CROWTACK SHALL BE STITCHED WITH THE CENTER RAY POINTED VERTICALLY TOWARD

BOTTOM AND THE TWO OPPOSITE RAYS POINTED HORIZONTALLY. THE THREE RAYS

SHALL BE EQUAL IN LENGTH. THE CROWTACK STITCHING SHALL BE EXECUTED IN

ACCORDANCE WITH STITCH ENLARGEMENT NUMBER 16-1-872 AND SHALL COMPLETELY

COVER THE PRESCRIBED BACKGROUND DESIGN AREA IN A CLOSE, DENSE AND

TIGHTLY DRAWN MANNER TO PRODUCE A CLEAR, SHARP EXECUTION OF DESIGN WITH

NO BACKGROUND CLOTH VISIBLE. THE RAISED AREA OF THE DESIGN SHALL BE

EQUAL TO THE REFERENCE SAMPLE. THE CROWTACK SHALL COVER THE

TOPSTITCHING AT THE BASE OF THE 'V" OPENING BUT SHALL NOT EXTEND INTO

THE "V" OPENING.".

UNDER STITCH/IN, DELETE "126 PER CROWTACK" AND SUBSTITUTE "SEE

S.E. NUMBER 16-1-872".

NOTE: THE CROWTACK SHALL NOT EXTEND INTO THE "V" AT THE BASE OF THE

NECK. THE CROWTACK SHALL COVER THE TOPSTITCHING AT THE BASE OF THE "V"

OPENING BUT SHALL NOT EXTEND INTO THE "V" OPENING. THE FINISHED TURNED

UP COLLAR BELOW THE "V" OPENING SHALL BE 1-3/4 (+/-1/4) INCH FROM THE

TOP OF THE CROWTACK TO FOLDED EDGE.".

PAGE 15, TABLE I, OPERATION 12. AT END OF OPERATION, ADD "AS AN

ALTERNATE, A PLASTIC BARB ATTACHING THE REMOVABLE SIZE TICKET TO THE

HANGER LOOP MAY BE USED PROVIDING THE ENTIRE TICKET IS VISIBLE BELOW THE

BOTTOM HEM AND THE TICKET WILL NOT TEAR EASILY."

PAGE 17, PARA. 3.8, DELETE TABLE II AND SUBSTITUTE:

TABLE II - SIZES AND MEASUREMENTS

A B B B C-A C-A C-A C-A SIZE

BUST SWEEP SWEEP SWEEP SLEEVE SLEEVE SLEEVE SLEEVE

JR MS WO LENGTH LENGTH LENGTH LENGTH

PETITE REGULAR TALL X-TALL

4 36-1/4 37 39 41 19 20 21 23 6 37-1/4 38 40 42 19 20 21 23 8 38-1/4 39 41 43 19 20 21 23 10 39-3/4 40-1/2 42-1/2 44-1/2 19 20 21 23 12 41-1/4 42 44 46 19 20 21 23 14 42-3/4 43-1/2 45-1/2 47-1/2 19 20 21 23 16 44-3/4 45-1/2 47-1/2 49-1/2 19 20 21 23 18 46-3/4 47-1/2 49-1/2 51-1/2 19 20 21 23 20 48-3/4 49-1/2 51-1/2 53-1/2 19 20 21 23 22 50-3/4 51-1/2 53-1/2 55-1/2 19 20 21 23 24 52-3/4 53-1/2 55-1/2 57-1/2 19 20 21 23 26 54-3/4 55-1/2 57-1/2 59-1/2 19 20 21 23 28 56-3/4 57-1/2 59-1/2 61-1/2 19 20 21 23

TOL, +/-1/2 +/-1/2 +/-1/2 +/-1/2 +/-1/2 +/-1/2 +1/2

"(C-A OR C-B SLEEVE LENGTH - MEASUREMENT SHALL BE TAKEN FROM UNDERARM

SEAM TO BOTTOM OF FINISHED SLEEVE HEM OR UNHEMMED SLEEVE.)".

PAGE 24, CROWTACK DEFECT A. LINE 1. AFTER "INSECURE," ADD "NOT

POSITIONED AS SPECIFIED,"

AFTER DEFECT "E", ADD THE FOLLOWING NEW DEFECTS:

F. NOT SPECIFIED SIZE OR NOT IN ACCORDANCE WITH STITCH

ENLARGEMENT OR GUIDE SAMPLE - MINOR A

G. INCOMPLETE COVERAGE, I.E., BACKGROUND CLOTH VISIBLE - MINOR B

H. BOBBIN THREADS VISIBLE, AFFECT APPEARANCE - MINOR B".

PAGE 28. AFTER "LABELS" ADD NEW CATEGORY OF DEFECTS:

"BAR CODE LABEL.

A. BAR CODE OMITTED OR NOT READABLE BY SCANNER - MINOR A

B. HUMAN-READABLE INTERPRETATION (HRI) OMITTED

OR ILLEGIBLE - MINOR A

C. NOT VISIBLE ON FOLDED, PACKAGED ITEM - MINOR A

D. CAUSE DAMAGES TO THE ITEM - MAJOR"

PAGE 29, PARA 4.4.2.3, DELETE AND SUBSTITUTE:

"4.4.2.3 INSPECTION LEVELS AND ACCEPTABLE LEVELS. THE INSPECTION LEVELS

AND ACCEPTABLE QUALITY LEVELS (AQL'S) EXPRESSED IN DEFECTS PER 100 UNITS

FOR VISUAL AND DIMENSIONAL EXAMINATIONS SHALL BE AS FOLLOWS:

INSPECTION

AQL'S LEVEL

FOR VISUAL EXAM. IN 4.4.2.1

MAJOR 1.0 III

MINOR 4.0 III

TOTAL (MAJOR, MINOR A & B) 10.0 III

FOR DIMEN. EXAM. IN 4.4.2.2

ONE CLASS 2.5 S-3"

PAGE 29, PARA. 4.4.3, LINE 8. DELETE "(SEE 6.5)" AND SUBSTITUTE "AND THE

AQL SHALL BE 2.5 DEFECTS PER 100 UNITS".

(REF. W2076)

ADDITIONAL INFORMATION FOR MIL-J-24949:

PAGE 18, PARA. 3.8, DELETE TABLE II (CONT'D) AND SUBSTITUTE:

TABLE II - SIZES AND MEASUREMENTS (CONT'D)

D D D D E

SIZE CENTER CENTER CENTER CENTER FRONT

BACK BACK BACK BACK LENGTH

LENGTH LENGTH LENGTH LENGTH PETITE

PETITE REGULAR TALL X-TALL

4 22-1/4 23-1/2 24-1/2 26-1/2 21-1/8 6 22-5/8 23-5/8 24-5/8 26-5/8 21-1/4 8 22-3/4 23-3/4 24-3/4 26-3/4 21-3/8 10 22-7/8 23-7/8 24-7/8 26-7/8 21-1/2 12 23 24 25 27 21-5/8 14 23-1/8 24-1/8 25-1/8 27-1/8 21-3/4 16 23-1/4 24-1/4 25-1/4 27-1/4 21-7/8 18 23-3/8 24-3/8 25-3/8 27-3/8 22 20 23-1/2 24-1/2 25-1/2 27-1/2 22-1/8 22 23-5/8 24-5/8 25-5/8 27-5/8 22-1/4 24 23-3/4 24-3/4 25-3/4 27-3/4 22-3/8 26 23-7/8 24-7/8 25-7/8 27-7/8 22-1/2 28 24 25 26 28 22-5/8

TOL, +/- 1/2 +/- 1/2 +/- 1/2 +/- 1/2 +/- 1/2

E E E F G

SIZE FRONT FRONT FRONT COLLAR COLLAR

LENGTH LENGTH LENGTH DEPTH WIDTH

REGULAR TALL X-TALL

4 22-1/8 23-1/8 25-1/8 9-1/2 10-5/8 6 22-1/4 23-1/4 25-1/4 9-1/2 11-1/8 8 22-3/8 23-3/8 25-3/8 9-1/2 11-5/8 10 22-1/2 23-1/2 25-1/2 9-1/2 12-1/8 12 22-5/8 23-5/8 25-5/8 9-1/2 12-5/8 14 22-3/4 23-3/4 25-3/4 9-1/2 13-1/8 16 22-7/8 23-7/8 25-7/8 9-1/2 13-5/8 18 23 24 26 9-1/2 14-1/8 20 23-1/8 24-1/8 26-1/8 9-1/2 14-5/8 22 23-1/4 24-1/4 26-1/4 9-1/2 15-1/8 24 23-3/8 24-3/8 26-3/8 9-1/2 15-5/8 26 23-1/2 24-1/2 26-1/2 9-1/2 16-1/8 28 23-5/8 24-5/8 26-5/8 9-1/2 16-5/8

TOL, +/- 1/2 +/- 1/2 +/- 1/2 +/- 1/2 +/- 1/4

PAGE 18, PARA. 3.8, DELETE TABLE II (CONT'D) AND SUBSTITUTE:

TABLE II - SIZES AND MEASUREMENTS (CONT'D)

C-B C-B C-B C-B

SIZE UNHEMMED UNHEMMED UNHEMMED UNHEMMED

SLEEVE SLEEVE SLEEVE SLEEVE

LENGTH LENGTH LENGTH LENGTH

PETITE REGULAR TALL X-TALL

4 21-1/2 22-1/2 23-1/2 25-1/2 6 21-1/2 22-1/2 23-1/2 25-1/2 8 21-1/2 22-1/2 23-1/2 25-1/2 10 21-1/2 22-1/2 23-1/2 25-1/2 12 21-1/2 22-1/2 23-1/2 25-1/2 14 21-1/2 22-1/2 23-1/2 25-1/2 16 21-1/2 22-1/2 23-1/2 25-1/2 18 21-1/2 22-1/2 23-1/2 25-1/2 20 21-1/2 22-1/2 23-1/2 25-1/2 22 21-1/2 22-1/2 23-1/2 25-1/2 24 21-1/2 22-1/2 23-1/2 25-1/2 26 21-1/2 22-1/2 23-1/2 25-1/2 28 21-1/2 22-1/2 23-1/2 25-1/2

TOL, +/- 1/2 +/- 1/2 +/- 1/2 +/- 1/2

PAGE 30, PARA. 4.4.4, LINE 6. DELETE "SEE 6.5)" AND SUBSTITUTE "AND THE

AQL, EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS SHALL BE 4.0 IN

ACCORDANCE WITH MIL-STD-105".

PAGE 31, PARA. 5.4, LINE 4. AFTER "BONDING:, DELETE REMAINDER OF

SENTENCE AND SUBSTITUTE "METHOD C OAND D OR FILM BONDING METHOD F OR G."

PAGE 32, PARA. 6.2. DELETE "H ACCEPTANCE CRITERIA (SEE 6.5)".

(REF. 93415)

DELETE CURRENT "BARCODE LABEL/TAG"

REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG. EACH ITEM SHALL BE INDIVIDUALLY

BAR-CODED WITH A PAPER TAG FOR PERSONAL

CLOTHING ITEMS. THE PAPER USED FOR THE TAGS

SHALL BE STANDARD BLEACHED SULFATE HAVING A

BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH

FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT

PRINTING. THE TAGS SHALL HAVE A HOLE AND

SHALL BE ATTACHED TO EACH ITEM BY A FASTENER,

CLEARLY LEGIBLE AND READABLE BY SCANNER.

THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE

A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC)

ASSIGNED FOR ALL NSNS BY THE GOVERNMENT.

THE INITIAL "UPC" MUST APPEAR BENEATH THE

CODE. THE BAR CODES FOR NSN AND UPC SHALL BE

A MEDIUM TO HIGH DENSITY AND SHALL BE

LOCATED SO THAT THEY ARE COMPLETELY VISIBLE

ON THE ITEM WHEN IT IS FOLDED AND PACKAGED

AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE

NO DAMAGE TO THE ITEM.

PACKAGING SECTION. ADD THE FOLLOWING:

NOTE: UNIVERSAL PRODUCT CODE INFORMATION

THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE

(UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON

WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/

TAGS:

BAR CODE OMITTED OR NOT MINOR A

READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) MINOR A

OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM MINOR A

CAUSES DAMAGE TO THE ITEM MAJOR

APPLICABLE DOCUMENTS: THE FOLLOWING LIST OF

DOCUMENTS IS APPLICABLE TO THIS PROCUREMENT:

STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS IDENTIFIED AS

ROLL #3746. FOLIAGE GREEN 504 IS TO BE USED AS SPECIFIED BY CONTRACT.

THIS APPLIES TO TYPE II, CLASS 1.

ADDITIONAL INFORMATION FOR V-B-871: NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR A-A-52094A:

SIZE 16; TWIST Z; TYPE II; 16.0 OUNCES NOMINAL; GLAZED FINISH

NO ADDITIONAL INFORMATION

(Ref. T1481 - 4/08).

ADDITIONAL INFORMATION FOR A-A-50198A

THREAD, GIMP, COTTON, BUTTONHOLE

STANDARD SAMPLE FOR COLOR FOLIAGE GREEN 504,

IS MIL-C-44436, ROLL #3728, (THE FOLIAGE GREEN

502 AREA PF THE PATTERN) AND REFERENC FOR SHADE

ONLY.

ADDITIONAL INFORMATION FOR NN-P-71:

NO ADDITIONAL INFORMATION FOLLOWS..

MIL-DTL 32075: LABEL FOR CLOTHING, EQUIPAGE, AND TENTAGE, GENERAL USE

REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

Page 6, TABLE I, "Physical requirements of the Type VI finished label" Under "Tearing strength" delete: "(lb.) minimum" and substitute: "(gms) minimum"

ADDITIONAL INFORMATION FOR DDD-T-86:

INTERIM CHANGES TO DDD-T-86H:

NOTE - REDUCED AQLS APPLY AS FOLLOWS:

PAGE 9, LINE 9, DELETE "0.4" AND SUBSTITUTE,

"0.28", FOR MAJORS. DELETE "1.5" AND SUBSTITUTE

"1.0", FOR TOTALS.

NOTE - COMMERCIAL ITEM DESCRIPTION A-A-52071

DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR

USE IN PREFERENCE TO DDD-T-86H

ADDITIONAL INFORMATION FOR MIL-P-15011: NO ADDL. INFORMATION FOLLOWS.

(ref. T1368 - 6/15/06)

ADDITIONAL INFORMATION FOR MIL-B-17757:

MIL-B-17757 IS CANCELLED WITHOUT REPLACEMENT.

ASTM-D-5118 IS AUTHORIZED FOR USE IN LIEU OF MIL-B-17757

(ref. T0857 - 6/15/06)

ADDITIONAL INFORMATION FOR MIL-C-87052:

INTERIM SPECIFICATION CHANGES TO MIL-C-87052B:

PAGE 6, PARA. 4.4.2.1, LINE 13, DELETE "25" AND

SUBSTITUTE "17", LINES 15 & 18, DELETE "38" AND

SUBSTITUTE "26".

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING:

INTERNATIONAL STANDARDS ISO 9001:2000 OR AMERICAN SOCIETY FOR QUALITY

ASQ 2003 VERSION.

HIGHER LEVEL INSPECTION SYSTEM:

THE INSPECTION SYSTEM(S) MUST BE SUBMITTED WITH YOUR BID PROPOSAL FOR

EVALUATION AND APPROVAL BY DSCP'S CONTRACTING OFFICER.

INSPECTION SYSTEM(S) COMPLIANT/BUT ARE NOT LIMITED TO THE INTERNATIONAL

STANDARDS ISO 9002 OR ASQ 2003 MAY BE UTILIZED IF TAILORED TO THE

SPECIFIC QUALITY ASSURANCE REQUIREMENTS IN THIS SOLICITATION.

ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN CANCELLED AND REPLACED BY

ASTM-D-6193, 4/98 STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE TO FED-STD-751.

(ref. T0216 - May 18, 2006)

ADDITIONAL INFORMATION FOR MIL-STD-105E:

NOTE: MIL-STD-105 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING:

"AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI/ASQC Z1.4 - SAMPLING

PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES".

APPLICATION FOR COPIES SHOULD BE OBTAINED FROM:

AMERICAN SOCIETY FOR QUALITY CONTROL

611 EAST WISCONSIN AVE

MILWAUKEE, WI 53202

MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE

MILITARY MARKING FOR SHIPMENT AND STORAGE - DATED

19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DEFENSE SUPPLY CENTER (DSCP) CLOTHING AND TEXTILE (C&T)

DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DSCP

C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS

OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER

TO BE LOADED FOR EACH SHIP- MENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT

HAND LETTERED, ON THE CONTAINER.

ADDITIONAL INFORMATION:

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR MIL-STD-2073-1:

NO ADDITIONAL INFORMATION FOLLOWS

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2

ADDITIONAL INFORMATION FOR DD 81337 16-1-872:

16-1-872 CROWTACK FOR JUMPERS

. 7/31/90 (Ref. T6646)

THIS IS A TYPE II (CODE 7) SHELF LIFE ITEM

WITH A SHELF LIFE OF 36 MONTHS (EXTENDABLE).

NOTE: PARAGRAPH 5.2.1 OF

MIL-STD-129P W/CHANGE 3 IS APPLICABLE.