Specifications for Trailer with Lift Gate.docx

SPECIFICATIONS FOR TRAILER WITH LIFT GATE

NOTE: Vendors that cannot comply with specifications are to be detailed on separate attachments.

MODEL: VS2RA

Unless otherwise specified in this Invitation to Bid (ITB), reference to a specific manufacturer or a specific product or model in the bid specifications does not restrict bidders to that manufacturer, product or model. This method is used to indicate the functional requirements (e.g., type, design, characteristics, quality) of the article desired. Bids may be considered on other manufacturers’ products or other models determined by the Purchasing Division to be the functional equivalent of the product or model referenced.

Vehicles furnished under this specification shall be the manufacturer's current year conventional design for the type and the allied equipment specified. All necessary accessories customarily furnished whether stipulated herein or not, with such modifications and attachments as may be necessary to enable the vehicle to function reliably and efficiently in sustained operation. Further, all vehicles furnished under this specification shall comply with the most current Nevada Revised Statutes, Federal Motor Vehicle Safety Standards, Federal Environmental Protection Agency Emission Control Standards for new motor vehicles (currently vehicles certified prior to the current year requirements shall not be considered).

Specify Make & Model ____________________________

MODEL AND PAYLOAD CAPACITY: COMPLIES ___YES NO___

· MODEL: VS2RA

· PAYLOAD CAPACITY: 55,000 LBS EVENLY DISTRIBUTED PAYLOAD CAPACITY

· GROSS VEHICLE WEIGHT RATING: 65,000 LBS GVWR

· GREENHOUSE GAS COMPLIANCE: THIS TRAILER IS NOT UTMC GHG2 CERTIFIED, GHG2 CERTIFICATION MAY REQUIRE W/HFC RESTRICTION

· DQS UPDATE NUMBER: DQS UPDATE #187

DIMENSIONS: COMPLIES ___YES NO___

· LENGTH: 3’0 OVERALL LENGTH

· OVERALL HEIGHT: 13’6” O/A HEIGHT ON 46-1/2” FIFTH HT FOR 107-1/8” POST HT

· WIDTH: 102-3/8” OVERALL WIDTH

DECK: COMPLIES ___YES NO___

· DECK TYPE: STRAIGHT DECK

FRONT SUBFRAME: COMPLIES ___YES NO___

· FRONT SUBFRAME: 4-1/4” DEEP BOX BEAM DESIGN FRONT SUBFRAME

· APPROACH PLATE: 9GA HIGH STRENGTH STEEL FULL WIDTH APPROACH PLATE

· KINGPIN PLATE: 3GA HIGH STRENGTH STEEL FULL WIDTH KINGPIN PLATE

· KINGPIN TYPE: AAR HARDNESS CRUCIFORM KINGPIN

· KINGPIN LOCATION: 36” KINGPING LOCATION

· CONDUIT: (1) CONDUIT THROUGH FRONT SUB 30-1/2” FROM C/L ON ROADSIDE

· COVER PLATE: EXTRUDED ALUM COVER ON FRONT FACE OF APPROACH PLATE

SUPPORT LEGS: COMPLIES ___YES NO___

· SUPPORT LEG LOCATION: SUPPORT LEG LOCATION OF 105” FROM C/L OF KINGPIN

· SUPPORT LEG CRANK: ROADSIDE SUPPORT LEG CRANK LOCATION

· SUPPORT LEG BRACING: BOLT ON SUPPORT LEG X-BRACING W/7GA 3-1/4” DEEP HIGH STRENGTH STEEL CHANNEL

· SUPPORT LEGS: JOST MODEL A401 ENHANCED 50,000 LBS CAPACITY SUPPORT LEGS WITH 10” X 10” CUSHION FOOT

FRAME, RAILS AND CROSSMEMBERS: COMPLIES ___YES NO___

· BOTTOM RAILS: 11” DEEP HEAVY DUTY EXTRU ALUM BOTTOM RAILS, TAPERED FRT AND REAR

· CROSSMEMBERS FRONT SUB TO LEGS: 4” ALUM I BEAM CMEMS W/(4) RIVET ENDCLIPS ON 12” C/L FRONT SUB TO SUPPORT LEGS

· CROSSMEMBERS OVER SUPPORT LEGS: (5) 4” STEEL I BEAM CMEMS W/(4) RIVET ENDCLIPS ON 12” C/L OVER SUPPORT LEGS

· CROSSMEMBERS LEGS TO REAR SUB: 5-1/2” ALUM I SHAPE CMEMS W/(4) RIVET ENDCLIPS ON 12” C/L SUPPORT LEGS TO REAR SUB

· CROSSMEMBERS OVER REAR SUBFRAME: 4” STEEL I BEAM CMEMS W/(4) RIVET ENDCLIPS ON 12” C/L W/STD REINF OF (1) ADDL CMEM IN REAR 34”

REAR SUBFRAME: COMPLIES ___YES NO___

· HORIZONTAL DOCK BUMPER: BASE SPEC: 7”HRZ BMPR W/ ¼” REINF PLATE AND 2” ADDL DOCK LOCK CLEARANCE X11”LG @ C/L OF BUMPER

· RUBBER DOCK BUMPERS: (1) PAIR ½” PROUD RUBBER DOCK BUMPERS

· VERTICAL AND HORIZONTAL DOCK BUMPER: BASE SPEC: DOT VERT W/NONSLIP 7” HORIZONTAL 22” MAX GROUND CLRN; MEETS IIHS-30% OFFSET TEST

SUSPENSION/AXLES/ACTUATION: COMPLIES ___YES NO___

· SLIDER SUSPENSION LOCATION: 70” REAR SUSPENSION LOCATION AND 166” FORWARD SUSPENSION LOCATION FOR 96” OF SLDR TRAVEL

· OIL SEALS: CONMET PREMIUM OIL SEALS (INCL W/CONMET PRESENT+WHEEL END SYSTEM)

· AIR BRAKE CHAMBERS: BENDIX ENDURASURE 3030 AIR BRAKE CHAMBERS

· AIR ACTUATION: ONE TANK AIR ACTUATION SYSTEM W/SPRING BRAKES

· SLACK ADJUSTERS: BENDIX VERSAJUST AUTOMATIC SLACK ADJUSTERS FOR USE W/BENDIX ENDURASURE OR TSE BRAKE CHAMBERS

· AIRRIDE DUMP VALVES: HENDRICKSON AUTOMATIC DUMP VALVE

· BRAKE LINING STYLE: HENDRICKSON HXS BRAKE LINING STYLE FOR USE W/INTRAAX

· AXLE SPINDLE NUTS: CONMET SPINDLE NUT (INCL. W/CONMET PRESET+WHEEL END SYSTEM)

· HUB PILOTED SYS W/OUTBOARD DRUMS FOR 16-1/2” X 7” BRAKES: 10 STUD HUB PILOTED SYS W/OUTBRD CAST DRUMS W/16-1/2” X 7” BRKS (STD W/CONMET PRESET+WHEEL END SYS)

· ANTILOCK BRAKE SYSTEMS (ABS): BENDIX TABS-8 ADVANCED W/ROLL STABILITY 2S/1M ABS

· WHEEL BEARING LUBRICATION: FACTORY CHOICE 80W-90 OIL

· AXLE MANUFACTURER: HENDRICKSON “VENTED” AXLES

· AXLE SPINDLE TYPE: N-SPINDLE TYPE (STANDARD WITH CONMET PRESET+ WHEEL END SYSTEM)

· WHEEL BEARINGS (CONES) AND RACES (CUPS) MANUFACTURER: CONMET BEARINGS (INCL W/ CONMET PRESET+WHEEL END SYSTEM)

· HENDRICKSON AIRRIDE SYSTEMS WITH INTEGRAL AXLES: BASE SPEC: HEND ULTRAA-K AIRRIDE/SLDR SYS, INCLS 49” AXL SPRD, HD SLDR AND ZERO MAINT DAMPIG (ZMD)

· SLIDER PIN RELEASE MECHANISM: HENDRICKSON QUIK DRAW AIR OPERATED SLIDER REPOSITIONING SYSTEM

· CONMET WHEEL END SYSTEMS: BASE SPEC: CONMET PRESET+IRON HUB SYSTEM, INCL: CONMET PREMIUM SEAL, BEARING, SPACER AND SPINDLE NUT

FRONT WALL: COMPLIES ___YES NO___

· FRONT CORNER POST: BASE SPEC: .080 EXTRUDED ALUM 4-3/4” RADIUS FRONT CORNER POST WITHOUT INSERT RECEIVERS

· FRONT WALL POSTS: 1” “J” EXTRU ALUM FRT WALL POST W(2) ADDL 3-1/4” DEEP STEEL REEFER UNIT SUPPORT POSTS

· FRONT PANELS: .040 ALUM FRONT PANELS

· ELECTRICAL NOSEBOX: UTM MULTI-FUNCT ZING RECEPT/BOX W/BRAKE ACT RELAY; DUAL CIRCUIT; 60 MIN TIMER; SWITCH; INDICATOR LGT

· REEFER UNIT AIR RETURN BULKHEADS: RETURN AIR BULKHEAD INSTALLED

· REEFER UNIT INSTALLATION: THERMO KING PRECEDENT S-700-50 230 AMP REEFER UNIT INSTALLED

· REFRIGERATION UNIT ACCESSORIES: FG RE-FLEX MOVABLE BULKHEAD WITH TWO TEMP FAN KIT; THERMO KING STANDARD STATUS LIGHT

· GLADHANDS AND RECEPTACLE: GLADHANDS (W/SCREEN) AND RECEPTACLE MOUNTED ON AN ALUM EXTRU OFFSET TO R/S 30”

· AIR CHUTE: NO AIR CHUTE

· REFRIGERATION UNIT FUEL TANK INSTALLATION: 50 GALLON ALUMINUM FUEL TANK INSTALLED

· PREP FOR THERMO KING FRONT FRONTMOUNT REFRIGERATION UNIT: PREP FOR TK PRECDNT S750I SINGLE TEMP 460V 30AMP 3 PHASE FRT MNT REEFER UNIT W/ELECTRIC STANDBY

· PLUG TO REAR FOR HIGH VOLTAGE REEFER UNITS: INST HBL430B7W PLUG/CABLE-30 AMP/480V/3 PHASE SHORE PWR@RR RS CRNR GUSSET (TK HIGH VOLT REEFER)

· PALLET STOPS AT FRONT WALL: (6) H.D. ALUM PALLENT STOPS 6” HIGH W/RUBBER BUMPER INSERTS

· REFRRIGERATION UNIT OPENING COVER: SHEET METAL COVER (INCLS SEALANT FULL PERIMETER OF OPENING)

SIDE WALLS: COMPLIES ___YES NO___

· SIDE PANELS: .040 ALUM FLAT SIDE PANELS

· SIDE POSTS: 1” “J” SHAPE EXTRU ALUM SIDE POST W/16”MAX C/L FROM FRT TO REAR OF SUPT LEGS W/24” C/L LEGS TO REAR

ROOF: COMPLIES ___YES NO___

· TOP RAILS: 6-3/8” HEAVY DUTY EXTRUDED ALUM TOP RAILS

· ROOF SKIN: .025 ONE PIECE ALUM COIL ROOF SKIN

· ROOF BOWS: 1” EXTRA ALUM “J” SHAPED ROOF BOWS ON 48” C/L

REAR DOORS: COMPLIES ___YES NO___

· REAR CASE AND BUCKPLATE MATERIAL: **NOTE** SST REAR DOOR CASE FOR ROLL-UP DOOR

· REAR DOOR ROLLUP TYPE: TODCO 2-1/2” “TODCOLD” INSULATED ROLL-UP DOOR W/PPW FIBERGLASS FACE

· INSTALL REAR LIFT GATE: LIFTGATE SPECIFICATIONS PER MAXON; INSTALL CUSTOMER FURNISHED MAXON BMR WELD-ON LIFTGATE WITH HEADER KIT FOR USE WITH PREP OPTION; FACTORY TO INSTALL MAXON COLUMN LIFT GATE PER SPECIFICATIONS

· REAR GUSSETS: ENAHCEND REAR CORNER GUSSET DESIGN FOR IMPROVED BOTTOM RAIL STRENGTH AT REAR OF TRAILER

· PREP FOR REAR LIFT GATE: PREP FOR MAXON BMR (BOLT-ON OR WELD-ON) LIFTGATE INCL LOWERED BOLT-ON S/T/T LGTS FOR 7” BUMPER

· REAR LIFT GATE ACCESSORIES: (2) DEEP CYCLE BATTERIES FOR LIFTGATE

· ROLL UP DOOR TRACK GUARD: EXTRUDED ALUMINUM TRACK GUARD FOR ROLL UP DOOR

SIDE DOOR: COMPLIES ___YES NO___

· SIDE DOOR: SIDE DOOR TYPE “E” AT 12” – LOCATE SIDE DOOR ON C/S

· SIDE DOOR STEP AND GRABHANDLE: MILD STEEL RETRACTING SIDE DOOR STEP W/EXPANDED METAL ON STEP

· GRAB HANDLE: (1) 36” VERTICAL BOLT-ON CHROME PLATED GRABHANDLE AT SIDE DOOR ON THE LOCK ROD SIDE

FLOOR: COMPLIES ___YES NO___

· FLOOR TYPE: 1-3/8” NOM HD EXTRU ALUM HIGH WEAR DRY FRT FLOOR KNURLED

· FLOOR TURN UP: 10” HIGH 3/16” HEAVY DUTY EXTRU ALUM NONTAPERED W/B INTEGRAL W/FLOOR (INCLUDES REINFORCING)

· TROUGHS: **NOTE** EXTRU ALUM TROUGH AT FRONT ONLY

· DRAINS: (2) DRAINS FRONT AND (2) REAR

· REAR THRESHOLD: **NOTE** ROLL UP DOOR REAR THRESHOLD

· FORK LIFT REINFORCING: BEARING GRID SYS AT REAR W/HDWD FILLERS FULL LENGTH AND ALUM 1 CORES REAR 36” OF FLR IN CTR 68”

· STUB POSTS: SIDEWALL STUB POST ON 48” C/L

INSULATION: COMPLIES ___YES NO___

· INSULATION TYPE: POLYURETHANE INSULATION FOAMED IN PLACE

· FRONT WALL THICKNESS: 4” THICK FRONT WALL

· SIDE WALL THICKNESS: 2-1/2” SIDE WALL INSULATION

· ROOF THICKNESS: 3” THICK ROOF

· FLOOR THICKNESS: 3” THICK FLOOR

· CROSSMEMBER FLOOR FILLERS: HARDWOOD FLOOR FILLERS FULL LENGTH

· FLOOR UNDERSKIN: .035 THERMOPLASTIC FLOOR UNDERSKIN

· SIDE DOOR THICKNESS: 2-1/2” SIDE DOOR INSULATION

LINING: COMPLIES ___YES NO___

· FRONT WALL LINING: .065(NOM) VERSITEX-UTILITY VR2U FRONT WALL LINING

· SIDE WALL LINING: .085 (NOM) VERSITEX-UTILITY VR3U SIDE WALL LINING

· ROOF LINING: .065 (NOM) VERSITEX-UTILITY VR2U ROOF LINING

· WEARBAND: 6” EXTRA HEIGHT 3/16” EXTRU ALUM HEAVY DUTY WEARBAND TOTAL OF 16” INCL REINFORCING BEHIND WEARBAND

· LOGISTIC RAILS: 2 – (1) ROW SERIES “E” GALV RECESS MTD LOG TRACK ON SIDE WALLS – LOCATED FIRST ROW OF “E” TRACK AT 30” FROM FLOOR TO C/L OF TRACH AND SECOND ROW AT 60” FROM FLOOR TO C/L OF TRACK

ELECTRICAL SYSTEM: COMPLIES ___YES NO___

· MAIN HARNESS: UTM MOISTURE RESISTANT “MULTI-PURPOSE” HARNESS W/INTERNAL GROUND AND 7-WAY PLUG

· ELECTRICAL RECEPTACLE: 7-WAY ELECTRICAL RECEPTACLE W/O CIRCUIT BREAKERS

· CLEARANCE LIGHT QUANTITY: 0-1-2-5 D.O.T. MINIMUM CLEARANCE LIGHT QUANTITY

· DOMELIGHTS MOUNTED IN CEILING: 6 – PHILLIPS 9-DIODE CRNR DOMELIGHT MTD LONGITUDINALLY @ SIDEWALL TO CELING CONNECTION, SWITCH REQD

· SIDE MOUNTED DIRECTIONAL LIGHT: GROTE SUPERNOVA LED COMBO SIDE MTD DIR/CLRN LIGHT ON BRACKET BELOW BOTTOM RAIL EACH SIDE

· STOP/TAIL/TURN LIGHTS: GROTE 4” L.E.D. (10-DIODE) STOP/TAIL/TURN LIGHTS (2) PER SIDE WITH BLACK SNAP-IN FLANGE

· LICENSE LIGHT: GROTE MICRONOVA L.E.D. LICENSE LIGHT

· CONSPICUITY TAPE LOCATION: FACTORY CHOISE CONSPICUITY TAPE

· UPPER CLEARANCE LIGHTS: FACTORY CHOICE LED UPPER SIDE RAIL CLEARANCE LIGHTS WITH 3” MOUNTING HOLE C/L

· LOWER CLEARANCE LIGHTS: GROTE MICRONOVA LED PC RATED LIGHT

· ABS (ANTI-LOCK) WARNING LIGHT: GROTE MICRONOVA LED PC RATED LIGHT

· STOP/TAIL/TURN LIGHT CONFIGURATION: GROUPED STOP/TAIL/TURN LIGHTS

· REAR HEADER CLEARANCE LIGHTS: GROTE MICRONOVA LED PC RATED GROMMET MOUNTED REAR HEADER ID/CLR LIGHTS

· AUXILIARY POWER: INSTALL PURKEYS TAPPS 300 TO CHARGE PALLET JACK

FINISH SPECIFICATIONS: COMPLIES ___YES NO___

· TOP FRONT AND TOP SIDE RAIL FINISH: NATURAL ALUM FINISH TOP FRONT AND TOP SIDE RAILS

· BOTTOM SIDE RAIL FINISH: NATURAL ALUM FINISH BOTTOM SIDE RAILS

· FRONT CORNER POST FINISH: NATURAL ALUMINUM FINISH FRONT CORNER POSTS

· FRONT PANEL FINISH: PREPAINTED WHITE FRONT PANELS

· SIDE PANEL FINISH: PREPAINTED WHITE SIDE PANELS

· FRONT APPROACH PLATE FINISH: NATURAL ALUM FINISH FRONT APPROACH PLATE

· FRONT SUBFRAME ASSEMBLY FINISH: FRONT SUBFRAME FULLY IMMERSED IN BLACK RUSE PREVENTATIVE FINISH (ZERO VOC HOT DIP)

· SUPPORT LEG FINISH: UTM BLACK SCHARPF ON SUPPORT LEGS

· REAR SUBFRAME FINISH: UTM BLACK SCHARPF ON REAR SUBFRAME

· REAR CASE FINISH: SATIN FINISH STAINLESS STEEL REAR CASE

· VERTICAL & HORIZONTAL DOCK BUMPER FINISH: UTM BLACK ENAMEL FINISH ON HORIZ DOCK BUMBER; BLACK SCHARPF ON VERTICAL DOCK BUMPER

· ROOF EXTERIOR FINISH: NATURAL ALUM ROOF EXTERIOR FINISH

MISCELLANEOUS: COMPLIES ___YES NO___

· MUDFLAP TYPE: MICHELIN ENERGY GUARD AERODYNAMIC 24”X28” BLACK PLASTIC MUDFLAP MTD W/STEEL REINFORCING STRAPS

· PERMIT HOLDER: TRUCKLITE #97960 ROUND PERMIT HOLDER MTD ON FRONT WALL – DEALER MUST SPECIFY LOCATION OF PERMIT/DOCUMENT/REGISTRATION HOLDER ON EITHER R/S, C/S OR C/L IN SPECIAL INSTRUCTIONS UNLESS OTHERWISE STATED IN THE OPTION DESCRIPTION. LOCATE PERMIT HOLDER ON FRONT WALL R/S

· DEALER SUPPLIES MATL AND LABOR: FREIGHT CHARGES TO DELIVER TRAILER TO LAS VEGAS; ON SPOT TIRE CHAINS MOUNTED ON FRONT AXLE

· FHWA INSPECTION REPORT: FHWA INSPECTION REPORT

· SIDE MOUNTED AERODYNAMIC AIR DEFLECTORS: OMIT BASE SPEC UTM USS120A-4 AERODYNAMIC SIDESKIRTS

TIRES AND WHEELS: COMPLIES ___YES NO___

· 22.5” X 8.25” STANDARD WIDTH WHEELS: 8 – 22.5 X 8.25 F.C STL 10 HUB PILOT

· 22.5” LOW PROFILE TIRES: 8 -295/75R 22.5 MICH X-LINE ENERGY – T2 14PLY 39.70”T/D,LOAD RG’G’ MAX SPEED RATED @ 75 MPH