Special Packaging Instructions -SPI-F01-060-1272.pdf
PDF 475 KB Posted
- Attached to
- Cylinder
- Solicitation number
- SPRHA4-26-R-1012
- Issued by
-
Defense Logistics Agency Aviation
About this file
This is a Special Packaging Instruction (SPI) document for military preservation and packaging requirements for a Cylinder Assembly, Actuating, Linear component. The document specifies packaging standards to ensure proper protection during storage and shipment, with two packaging levels (Level A and Level B) available depending on operational requirements. Both levels utilize ASTM D6251 closure standards and follow Military Preservation IAW MIL-STD-2073 guidelines. The cylinder assembly must be cleaned and dried per MIL-STD-2073 specifications with no preservative application required. Container dimensions and specifications vary by level: Level A containers measure 42 inches in length, 18 1/2 inches in width, and 14 1/4 inches in depth with a gross capacity of 10.309 cubic feet; Level B containers are identical in dimension but accommodate only 116 cubic feet of capacity. The item weighs 55 pounds and has dimensions of 29 1/2 by 9 1/2 by 6 inches.
The packaging assembly requires fifteen component materials including steel strapping, cushioning foams (A-A-59135 Class 1 Grade A), reinforced tape, laminated sections using A-A-1936A Type II adhesive, wrapping material, wooden pallets and dunnage, and steel skids. All wooden components must comply with International Standards for Phytosanitary Measures (ISPM No. 15) requirements, including use of debarked wood and heat treatment to 56 degrees Celsius for 30 minutes with ALSC accreditation marking. The document includes caution notices regarding packaging substitution flexibility, overseas shipment requirements, and specific assembly instructions for cushion configurations, reinforcement placement, and void filling to ensure snug positioning of the item within the container. The SPI was last revised in January 2018 with updated specifications and distribution limitations to Department of Defense and DOD contractors only.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| SPRHA426R1012 CUI SSI.pdf | ||
| Engineering Data Requirements.pdf | ||
| Packaging Statement of Work.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DEPARTMENT OF DEFENSE AND U.S. DOD CONTRACTORS ONLY, ADMINISTRATIVE OR OPERATIONAL USE, 19 JANUARY 2018. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO 406
SCMS/GULAA, (PACKAGING DIVISION), HILL AFB, UTAH 84056.
DESTRUCTION NOTICE: FOLLOW THE PROCEDURES IN DOD 5220.22-M, NATIONAL INDUSTRIAL SECURITY PROGRAM OPERATING MANUAL (NISPOM), SECTION 5-705, OR DOD 5200.1-R, INFORMATION SECURITY PROGRAM, CHAPTER VI. FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.
CAUTION NOTICES
INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES
REVISION OF ISPM NO. 15
REVISION OF WOOD PACKAGING MATERIAL FOR INTERNATIONAL TRADE
THE FOLLOWING STATEMENT IS IN COMPLIANCE WITH THE UNITED NATIONS-IMPLEMENTED RESTRICTIONS ON WOOD
PACKAGING MATERIAL (WPM). THIS REQUIREMENT IS SPECIFICALLY CONCERNED WITH INVASIVE SPECIES SUCH AS THE
PINEWOOD NEMATODE. WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAMES, AND CLEATS. THE STATEMENT BELOW CITES THE REQUIREMENTS IN DETAIL AND
COVERS LUMBER FOR BUILDING CONTAINERS AND PALLETS USED FOR DELIVERIES, RESULTING IN SHIPMENTS WORLDWIDE
(DIRECT, OR THROUGH AIR LOGISTICS CENTERS (ALC), CONTAINER CONSOLIDATION POINTS (CCP), OR OTHER BASES).
WOODEN LUMBER, WOODEN PALLET AND PACKAGING/CONTAINER STATEMENT:
ALL WOODEN LUMBER, WOODEN PALLETS, AND WOODEN CONTAINERS PRODUCED ENTIRELY OR IN PART OF WOOD
PACKAGING MATERIAL (WPM) SHALL BE CONSTRUCTED FROM DEBARKED WOOD IN ADDITION TO THE APPLICATION OF
HEAT-TREATED (HT) MATERIAL (HT TO 56 DEGREES CENTIGRADE OR 133 DEGREES FAHRENHEIT FOR 30 MINUTES).
CERTIFICATION/MARKING IS REQUIRED BY AN ACCREDITED AGENCY RECOGNIZED BY THE AMERICAN LUMBER STANDARDS
COMMITTEE (ALSC). FOR REFERENCE DOCUMENTATION, SEE LATEST REVISION OF "INTERNATIONAL STANDARDS FOR
PHYTOSANITARY MEASURES (ISPM NO. 15), "REGULATION OF WOOD PACKAGING MATERIAL IN INTERNATIONAL TRADE."
NOTES
1. LAMINATE REF.-3 TO REF.-4 USING A-A-1936A, TYPE II ADHESIVE OR EQUAL.
2. LAMINATE REF.-9 TO REF.-8 (BOTTOM CUSHION ONLY) USING A-A-1936, TYPE II ADHESIVE OR EQUAL.
3. CRIMP REINFORCEMENTS REF.-10, AND INSERT IN POSITION AS ILLUSTRATED.
4. FOR SERVO ACTUATOR WITH SHORT RAMS, MOVE REF.-10 REINFORCEMENTS IN AGAINST RAMS THEN FILL WITH
A-A-59135, CLASS 1, GRADE A OR EQUAL. INSURE VOID IS FILLED VERY TIGHT TO EQUAL SURROUNDING CUSHIONING
VALUE.
5. USING REF.-12, FILL EXCESS VOID TO INSURE ITEM IS SNUG WITHIN CUSHIONING CUT-OUTS.
File details come from the government source that posted it. Updated .