Attachment_G___C_Energy_QAPS.pdf

DEFENSE LOGISTICS AGENCY ENERGY Page 1 of 2

8725 JOHN J. KINGMAN ROAD

FORT BELVOIR, VIRGINIA 22060-6222

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.08-1 TURBINE FUEL, AVIATION (JET A) (DLA ENERGY MAY 2018)

Jet A shall conform to the requirements of ASTM D 1655, Standard Specification for Aviation Turbine Fuels, except as modified below, at the custody transfer point

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE

DLA ENERGY PRODUCT

CODE

9130-00-359-2026 Turbine Fuel, Aviation, Jet A JAA

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits.

(a) SPECIFICATION MODIFICATIONS

(1) Microseparometer (MSEP).

(i) The following MSEP ratings apply in the presence of the additives listed below. Values apply at point of manufacture:

Jet-A Additive MSEP Rating, min.

Fuel System Icing Inhibitor (FSII) 85

Corrosion Inhibitor/Lubricity Improver (CI/LI) 80 Fuel System Icing Inhibitor (FSII) and

Corrosion Inhibitor/Lubricity Improver (CI/LI)

(b) ADDITIVES.

(1) Additives shall not be premixed with other additives before injection into the fuel.

(2) FUEL SYSTEM ICING INHIBITOR (FSII). When required by contract line item-

(i) FSII shall be added to the fuel and shall be Diethylene Glycol Monomethyl Ether (DIEGME) conforming to ASTM D4171, Standard Specification for FSIIs, Type III or MIL-DTL-85470B, dated June 15, 1999 Inhibitor, Icing, Fuel System, High Flash, NATO Code Number S-1745.

(ii) FSII shall be added to the fuel so that the resulting concentration in the final blend is between 0.07% and 0.10% by volume.

(iii) When using the 20-ounce aerosol can to introduce FSII during over the wing refueling, determine the fuel quantity and calculate the amount of required additive. This additive shall be added gradually during filling to permit proper blending in the fuel. One can of aerosol additive will inhibit 180 gallons of fuel to 0.087 percent by volume. The use of aerosol FSII is not permitted for U.S. Navy aircraft refueling.

(3) CORROSION INHIBITOR/LUBRICITY IMPROVER (CI/LI). When required by contract line item-

(i) The additive must conform to MIL-PRF-25017H with Amendment 1, dated August 4, 2011 Inhibitor, Corrosion/Lubricity

Improver, Fuel Soluble (NATO S-1747), found in ASSIST and shall be listed in the electronic Qualified Products List (QPL)-25017, located in the Qualified Products Database (QPD) found at http://assistdocs.com.

(ii) The concentration of CI/LI added to the fuel must be between the minimum effective concentration and the maximum allowable concentration as listed for the CI/LI in QPL-25017.

(4) STATIC DISSIPATER ADDITIVE (SDA). When required by contract line item-

(i) SDA shall be added to the fuel and the conductivity limits of 50 to 600 picosiemens per meter (pS/m) at ambient temperature or 29.4oC (85oF), whichever is lower, unless otherwise directed by the procuring activity.

(ii)

(5) METAL DEACTIVATOR (MDA). MDA shall not be used unless the supplier has obtained PRIOR written consent from the procuring activity.

(6) Product shall be homogeneously mixed. Until all aviation turbine fuel tanks are coated, it is acceptable to perform stratification tests in lieu of circulating tanks to achieve homogeneity.

http://assistdocs.com/

DEFENSE LOGISTICS AGENCY ENERGY Page 2 of 2

(c) REPORTS. Refer to the MATERIAL INSPECTION AND RECEIVING REPORT (QAP E40.01) contract provision for reporting requirements.

(1)

Signature

Prepared by:

Quality / Technical Support Office Approval:

Contracting Approval:

C16.14 FUEL, ETHANOL (PC&S) (DLA ENERGY JUL 2011)

In the event that a Federal, State, or local environmental requirement is more stringent than a specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery.

(a) PRODUCT PERFORMANCE REQUIREMENTS. Product shall conform to the latest revision of ASTM D5798.

(b) BLENDING. Product shall be blended prior to delivery. Manifold blending at time of delivery and blending in the receipt tank is not permitted. The resultant blended product must meet all performance requirements specified in the contract.

Quality / Technical Support Office Approval: Prior approval as contract provision

Contracting Approval: Prior approval as contract provision

Legal Approval:

(Only required for E QAPs)

DMM0076

Typewritten Text DISTRIBUTION STATEMENT - A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.15 GASOLINE, AVIATION (GRADES 80/100LL) (DLA ENERGY OCT 2014)

Aviation Gasoline shall conform to the latest revision of ASTM D910 or Defense Standard 91-90.

Quality / Technical Support Office Approval: Prior approval as contract provision

Contracting Approval: Prior approval as contract provision

Legal Approval:

(Only required for E QAPs)

DMM0076

DEFENSE LOGISTICS AGENCY ENERGY Page 1 of 1

Quality / Technical Support Office Approval:

C16.23-2 COMMERCIAL MARINE GAS OIL MINIMUM REQUIREMENTS (BUNKERS) (DLA ENERGY FEB 2019) Product Classification

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE UNIT OF ISSUE

9140-01-313-7776 Marine Gas Oil MGO Gallons 9140-01-417-6843 Marine Gas Oil MGO Metric Tons

Supplies delivered under this contract, the Contractor shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. The Contractor shall also comply with all applicable International Agreements, Treaties, Conventions, and the like to which the United States is a party or with whose terms the receiving activity has otherwise agreed to comply, including but not limited to, the requirements of MARPOL 73/78 Annex VI Regulations 14 & 18. The Contractor shall be responsible for determining the existence of all such requirements prior to the time deliveries are made. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits.

The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that an International, Federal, State, and /or local environmental requirement, as identified above, is more stringent than a requirement contained in this contract, the Contractor shall deliver product(s) that complies with the more stringent requirement. Product(s) that fails to meet the more stringent requirement will be considered nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s). In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to the requirements of the latest revision of ISO 8217, Category ISO-F-DMA. In Accordance with Annex A of ISO 8217, the de minimis value of FAME shall be 0.5 volume %. Offeror/Supplier shall ensure product offered meets ISO 8217 de minimis FAME requirement. The following are additional requirements or approved modifications to specifications.

(a) SPECIFICATION MODIFICATIONS

(1) TESTING

(i) Hydrogen sulfide testing is not required

(ii) In addition to ISO 8217 approved sulfur tests, the following test methods are approved for Sulfur testing: ASTM D129, D5453, D1266, D1552, D2622, D3120, D6920, D7039, or ISO16591. See section 6.3 of ISO 8217 for referee test method. For a total sulfur content of less than 0.05 mass % (500 ppm), the latest revision of ASTM D5453 is the recommended ASTM method.

(iii) The following test methods are approved for FAME testing per ISO 8217: IP 579 or ASTM D 7963. Test method EN 14078 is an equivalent test method for IP 579 and approved for FAME testing. See section 6.10 ISO 8217 for referee test method.

(iv) ASTM International Test Methods equivalent to ISO test methods referenced in ISO 8217, DMA testing, are approved for use.

(2) Environmental

(i) Per MARPOL 73/78 Annex VI Regulation 14, for ships operating in the most current emission control areas, the sulfur content of the fuel shall not exceed 0.10% mass (1000 ppm).

(ii) Per 40 CFR Section 80.510, the Marine Gas Oil sulfur requirement for all refineries and deliveries to ports within Continuous United States (CONUS) shall not exceed 0.0015 mass % (15 ppm) sulfur.

(b) ADDITIVES: Marine Gas Oil shall contain no black dye or dyes.

(c) OTHER REQUIREMENTS: Unless otherwise indicated by the Contractor in writing, prior to award, and in accordance with the

EVALUATION (SHIP’S BUNKERS) provision, the product offered shall fully meet the applicable specification. The supplier shall provide to the receiving vessel a “Statutory Sample” of at least 500 mL in volume, taken from the receiving vessel’s inlet bunker manifold, together with a Bunker Delivery Note (BDN). This sample will be sealed and carry a sample tag that provides the documentation required per MARPOL 73/78 Annex VI Regulation 18

C16.27 FUEL, BIODIESEL (B20) (DLA ENERGY OCT 2014)

In the event that a Federal, State, or local environmental requirement is more stringent than a specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. Offered product shall conform to the following requirements that define a fuel suitable for use in automotive diesel engines:

(a) PRODUCT COMPOSITIONAL AND PERFORMANCE REQUIREMENTS. The finished fuel shall conform to ASTM D7467, with a biodiesel blend percentage of 20 +/- 1 percent, with the exception that the biodiesel component, per ASTM D6751, shall be derived solely from either virgin or used vegetable oils. Biodiesel derived from animal fats or tallows shall not be used. Product classification is shown below:

MAXIMUM

DLA ENERGY PRODUCT SULFUR

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED DYE

9140-01-470-4520 Grade Number B20 S15 BDI 15 µg/g (ppm) No

Suppliers of biodiesel blends shall be certified as either BQ-9000 Producers or BQ-9000 Marketers as set forth by standards adhering to The National Biodiesel Accreditation Program. Documentation of BQ-9000 certification shall be submitted at time of offer.

(b) BLENDING. Product shall be blended prior to delivery. Manifold blending at time of delivery and blending in the receipt tank is not permitted. The resultant blended product must meet all performance requirements specified in the contract.

(c) LOW TEMPERATURE OPERABILITY. For fuel supplied during the months of October through March, the low temperature performance of B20 biodiesel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X3 of ASTM D 7467.

(d) ENVIRONMENTAL PROTECTION AGENCY (EPA) REGISTRATION. B100 product must be EPA registered in accordance with 40 CFR Part 79, Registration of Fuels and Fuel Additives. The Contractor shall provide a copy of the EPA registration letter to the Contracting Officer at the time of offer.

Quality / Technical Support Office Approval: Prior approval as contract provision

Contracting Approval: Prior approval as contract provision

Legal Approval:

(Only required for E QAPs)

DMM0076

Quality/Technical Support Office Approval

C16.69-1 GASOLINE AUTOMOTIVE, UNLEADED, REGULAR (PC&S) (DLA ENERGY JUN 2017)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-00-148-7103 Gasoline, Regular Unleaded MUR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those requirements.

GASOLINE AUTOMOTIVE, UNLEADED, REGULAR. Gasoline shall conform to each country specification as listed below:

COUNTRY SPECIFICATION NATIONAL STOCK NUMBER

AUSTRALIA FUEL STANDARD (PETROL) 2001

CANADA CAN/CGSB-3.5-2001

JAPAN JIS K 2202

PHILIPINES PNS/DOE QS 008:2012 9130-00-148-7103

MIDDLE EAST EN 228

ALL OTHER REGIONS ASTM D4814

LOCAL SPECIFICATIONS: In-country specifications not meeting the specification requirements in the chart above, but meet local requirements may also be submitted for review and approval.

(a) OCTANE REQUIREMENTS

(1) Unleaded regular automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or

Anti-Knock Index (AKI) limits described in the specification listed for each country or the in-country requirements when applicable.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification listed for each country requirements when applicable.

(b) OXYGENATE REQUIREMENTS.

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

Quality/Technical Support Office Approval

C16.69-3 GASOLINE AUTOMOTIVE, UNLEADED, PREMIUM (MUP) (DLA ENERGY JUN 2017)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-00-148-7104 Gasoline, Premium Unleaded MUP

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those requirements.

GASOLINE AUTOMOTIVE, UNLEADED, PREMIUM. Gasoline shall conform to each countries specification as listed below:

COUNTRY SPECIFICATION NATIONAL STOCK NUMBER

AUSTRALIA FUEL STANDARD (PETROL) 2001

CANADA CAN/CGSB-3.5-2011

JAPAN JIS K 2202

PHILIPPINES PNS/DOE QS 008:2012 9130-00-148-7104

MIDDLE EAST EN 228

ALL OTHER REGIONS ASTM D4814

LOCAL SPECIFICATIONS: In-country specifications not meeting the specification requirements in the chart above, but meet local requirements may also be submitted for review and approval.

(a) OCTANE REQUIREMENTS

(1) Unleaded premium automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or

Anti-Knock Index (AKI) limits described in the specification listed for each country or the in-country requirements when applicable.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification listed for each country requirements when applicable.

(b) OXYGENATE REQUIREMENTS.

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-7 GASOLINE, AUTOMOTIVE, UNLEADED (REFORMULATED GASOLINE) (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-01-388-4080 Reformulated Gasoline, Regular MRR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

GASOLINE Product shall conform to the latest revision of ASTM D4814, as modified by the Environmental Protection Agency (EPA) requirements detailed in 40 CFR Part 80 - "Regulation of Fuels and Fuel Additives; Subpart D Reformulated Gasoline”. In part, these regulations mandate that the Phase II complex model reformulated gasoline must meet three emissions performance requirements when compared to the baseline gasoline marketed by a refiner in 1990: a 27 percent reduction in emissions of volatile organic compounds (VOCs), a 22 percent reduction in emissions of toxic pollutants, and a 7 percent reduction in emissions of oxides of nitrogen (NOx).

Further, Phase II complex model reformulated gasoline must meet two compositional requirements: 1.3 volume percent maximum benzene and no heavy metals (lead and manganese are examples of such metals).

The latest revision of specification ASTM D 4814 applies with the following specific requirements:

(1) OCTANE REQUIREMENTS.

(i) Reformulated gasoline shall meet the minimum AKI of 87.

(ii) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM D 4814.

(iii) For regular unleaded gasohol, in addition to an AKI of 87 minimum, the MON must not be less than 82.

(2) OXYGENATE REQUIREMENTS.

(i) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, suppliers shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(ii) Blending of permissible oxygenate into reformulated gasoline shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-8 GASOLINE, AUTOMOTIVE, UNLEADED (REFORMULATED GASOLINE) (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-01-388-4513 Reformulated Gasoline, Midgrade MMR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

GASOLINE Product shall conform to the latest revision of ASTM D4814, as modified by the Environmental Protection Agency (EPA) requirements detailed in 40 CFR Part 80 - "Regulation of Fuels and Fuel Additives; Subpart D Reformulated Gasoline”. In part, these regulations mandate that Phase II complex model reformulated gasoline must meet three emissions performance requirements when compared to the baseline gasoline marketed by a refiner in 1990: a 27 percent reduction in emissions of volatile organic compounds (VOCs), a 22 percent reduction in emissions of toxic pollutants, and a 7 percent reduction in emissions of oxides of nitrogen (NOx).

Further, Phase II complex model reformulated gasoline must meet two compositional requirements: 1.3 volume percent maximum benzene and no heavy metals (lead and manganese are examples of such metals).

The latest revision of specification ASTM D 4814 applies with the following specific requirements:

(1) OCTANE REQUIREMENTS.

(i) Reformulated gasoline shall meet the minimum AKI of 89.

(ii) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM D 4814.

(2) OXYGENATE REQUIREMENTS.

(i) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, suppliers shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(ii) Blending of permissible oxygenate into reformulated gasoline shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-10 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-524-5174 Grade Number 1-D S15 (ULSD) DS1

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975, Grade Number 1-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above.

(a) ADDITIVES.

(1) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY / CLOUD POINT REQUIRMENTS. The low temperature performance of diesel fuel shall be defined by the following property. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975.

Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-11 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-524-0139 Grade Number 2-D S15 (ULSD) DS2

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited above. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above. Maximum sulfur content shall be 0.0015 wt%.

(a) ADDITIVES.

(1) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

. E.1290973453

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-12 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-541-6760 Grade Number 2-D S15 (ULSD) DSS

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975, Grade Number 2-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above

(a) ADDITIVES.

(1) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

(d) DYE REQUIREMENT. Product shall have addition of red dye. As a means of identification, the Internal Revenue Service (IRS) requires that a red dye, identified as Solvent Red 164 (alky derivatives of azo benzene azo naphthol), must be added to all nontaxable diesel and all nontaxable kerosene used for purposes other than military jet fuel. The definitions of diesel and kerosene are provided in 26 CFR Section 48.4081-1. The minimum concentration is provided in 40 CFR Part 80.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-13 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-541-6767 Grade Number 1-D S15 (ULSD) DSW

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975, Grade Number 1-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above. Maximum sulfur content shall be 0.0015 wt%. Product shall have addition of red dye

(a) ADDITIVES.

(1) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

(d) DYE. As a means of identification, the Internal Revenue Service (IRS) requires that a red dye, identified as Solvent Red 164 (alky derivatives of azo benzene azo naphthol), must be added to all nontaxable diesel and all nontaxable kerosene used for purposes other than military jet fuel. The definitions of diesel and kerosene are provided in 26 CFR Section 48.4081-1. The minimum concentration is provided in 40 CFR Part 80.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-14 GASOHOL FUEL SPECIFICATIONS (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-01-090-1093 Gasohol, Regular Unleaded GUR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasohol Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically throughout the United States. Therefore, Contractors are expected to know the local, State, or Federal RVP requirements of areas being supplied and comply with those requirements. In-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

Products shall conform to the latest edition of ASTM D4814 for Gasohol, Regular grade Unleaded.

(a) OCTANE REQUIREMENTS.

(1) Unleaded automotive gasohol shall have a minimum AKI Octane rating of 87.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM

D 4814.

(3) For regular unleaded gasohol, in addition to an AKI of 87 minimum, the MON shall not be less than 82.

(b) OXYGENATE REQUIREMENTS.

(1) Ethanol concentration shall be between 9 and 11 volume percent.

(2) Blending of ethanol into gasoline to make gasohol shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

(c) LEAGLE REQUIREMENT: In accordance with Executive Order 12261 of January 5, 1981, "Gasohol in Federal Motor Vehicles,"

Gasohol may be considered an acceptable substitute for Unleaded Gasoline. The Unleaded Gasoline items that permit the substitution of Gasohol are identified in the Schedule. Contractors are required to state, for each line item in their offer, whether Gasohol will be provided. Contractors will not be permitted to substitute Unleaded Gasoline under line items awarded as gasohol. Also, Contractors are not permitted to substitute gasohol for gasoline under line items awarded as gasoline, except when Government regulations mandate use of fuel containing an oxygenate for control of carbon monoxide pollution.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-15 GASOHOL FUEL SPECIFICATIONS (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-01-355-2393 Gasohol, Midgrade Unleaded GUM

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasohol Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically throughout the United States. Therefore, Contractors are expected to know the local, State, or Federal RVP requirements of areas being supplied and comply with those requirements. In-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

Products shall conform to the latest revision of ASTM D4814 for Gasohol, Midgrade Unleaded.

(a) OCTANE REQUIREMENTS.

(1) Unleaded automotive gasohol shall have a minimum AKI Octane rating of 89.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM

D 4814.

(b) OXYGENATE REQUIREMENTS.

(1) Ethanol concentration shall be between 9 and 11 volume percent.

(2) Blending of ethanol into gasoline to make gasohol shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

(c) LEAGLE REQUIREMENTS: In accordance with Executive Order 12261 of January 5, 1981, "Gasohol in Federal Motor Vehicles,"

Gasohol may be considered an acceptable substitute for Unleaded Gasoline. The Unleaded Gasoline items that permit the substitution of Gasohol are identified in the Schedule. Contractors are required to state, for each line item in their offer, whether Gasohol will be provided. Contractors will not be permitted to substitute Unleaded Gasoline under line items awarded as gasohol. Also, Contractors are not permitted to substitute gasohol for gasoline under line items awarded as gasoline, except when Government regulations mandate use of fuel containing an oxygenate for control of carbon monoxide pollution.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-16 GASOHOL FUEL SPECIFICATIONS (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-01-090-1094 Gasohol, Premium Unleaded GUP

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasohol Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically throughout the United States.