SP7000-18-Q-0053_Attachment_1_-_MIL-P-10831B.pdf

Source: https://assist.dla.mil -- Downloaded: 2018-03-13T13:17Z Check the source to verify that this is the current version before use.

Attachment 1 SP7000-18-Q-0053

S ou rc e:

h tt ps

/a ss is t.

dl a.

m il

D ow nl oa de d:

8-

-1

3T

:1 7Z

C he ck t he s ou rc e to v er ify t ha t th is i s th e cu rr en t ve rs io n be fo re u se

S ou rc e:

h tt ps

/a ss is t.

dl a.

m il

D ow nl oa de d:

8-

-1

3T

:1 7Z

C he ck t he s ou rc e to v er ify t ha t th is i s th e cu rr en t ve rs io n be fo re u se

MIL-P-10831B

AMENDMENT 4

16 August 1999

SUPERSEDING

INTERIM AMENDMENT 3(AR)

18 December 1993

MILITARY SPECIFICATION

PAPER, TARGET

This Amendment forms a part of MIL-P-10831B, dated 4 September 1964 and is approved for use by all Departments and Agencies of the Department of Defense.

2.2: Add TAPPI Standard "T402M":

T402M - Standard Conditioning and Testing Atmosphere for Paper, Board, Pulp, Handsheets, and Related Products.

3.2: Delete ". . . chip numbers 37855 through 37886 of Federal Standard No.

595. (See 6.1) "and substitute ". . . chip number 37855 or 37866 of Federal Standard No. 595. (See 6.1)"

3.5.2: Second line, delete ". . .95 + 5 pounds/500 sheets/24 inches x 36 inches," and substitute "120 + 5 pounds/500 sheets/24 inches x 36 inches."

3.6.2: In second line delete "0.010 + 0.0005 inch" and substitute "0.011 +

0.0005 inches"

3.7: Delete Table I in its entirety and substitute the following:

TABLE I. Minimum Physical Characteristics

Characteristics Type I Type II

Tear, grams Cross direction 50 130

AMSC N/A 1 OF 3 FSC 9310

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

INCH-POUND

MIL-P-10831 was inactivated after 5 June 1996 for new design.

Source: https://assist.dla.mil -- Downloaded: 2018-03-13T13:17Z Check the source to verify that this is the current version before use.

AMENDMENT 4

3.9: Delete in its entirety and substitute:

"3.9 Pick strength. The pick strength, or the surface bond strength, of the printing side (see 3.4.1) of the paper shall withstand not less than the values specified below with no picking, when tested as specified in Table II:

Type I Nr6A Dennison Standard Wax Type II Nr8A Dennison Standard Wax"

3.10: Delete "6 + 0.5 ph" and substitute "7 + 1.5 ph"

Delete Table II in its entirety and substitute the following:

TABLE II. Instructions for Testing

Specification Reference

Requirements Number Results Reported Test (1) Applicable Determinations(2) As Numerically(3)

Characteristics Requirement Method to Lot Avg. Per Sample Unit to Nearest

Basis weight 3.5.1, 3.5.2 110 X 1 (Avg. of 5 sheets) Pound Thickness 3.6.1, 3.6.2 173 X Avg. of 3 0.0001 inch Tear, grams cross direction Table I 170 X Avg. of 5 Grams Gloss 3.8 T-480M X Avg. of 3 Unit Pick strength 3.9 T-459M X Avg. of 3 Number PH 3.10 200 - (2) Composite 0.1 ph Unit Penetration 3.11 4.4.2 X 1 (10 rounds) 10 Percent

Note:

1. Three digit numbers refer to Federal Specification UU-P-31. Numbers preceded by the letter "T" refer to TAPPI Standard Methods. Test Methods shall be performed in accordance with the applicable procedures, except that the stipulation as to the number of specimens to test, number of determinations to perform or number of results to report, shall be as indicated in this table. All testing shall be performed under atmospheric conditions as specified in 4.4.1.

2. The composite shall consist of representative portions taken from each sample unit and combined into a single sample.

3. Test reports shall include all values on which results are based.

Source: https://assist.dla.mil -- Downloaded: 2018-03-13T13:17Z Check the source to verify that this is the current version before use.

AMENDMENT 4

6.2, In first line delete: "37855 through 37886" and substitute "37855 and 37886".

This specification has been changed from Interim Amend 3 to Amend 4 without any changes being incorporated and Amend 4 makes specification a fully coordinated document.

Custodian: Preparing activity:

Army-AR Army-AR Navy-EC Air Force-11

Review activities: (Project 9310-0123) Army-AT, AV, CR Navy-SH,YD Air Force-10, 85

Source: https://assist.dla.mil -- Downloaded: 2018-03-13T13:17Z Check the source to verify that this is the current version before use.

DETAIL SPECIFICATION

Paper, Target

MIL-P-10831B, dated 16-Aug-1999, remains inactive for new design; however, the document is valid for use.

Reviewer Activities:

Army - AT, AV, CR Navy - SH, YD

DLA - GS

NOTICE OF

VALIDATION

INCH-POUND

MIL-P-10831B

NOTICE 2

08-Oct-2013

NOTE: The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.dla.mil.

AMSC N/A FSC 9310

Custodians:

Army - AR Navy - EC Air Force - 85

Preparing Activity:

Army - AR

Source: https://assist.dla.mil -- Downloaded: 2018-03-13T13:21Z Check the source to verify that this is the current version before use.