SOW Spectrum Analyzer.docx

Statement of Work Spectrum Analyzer

I. Background

The Photonics and Optomechanics Group at the National Institute of Standards and Technology (NIST) develops photonic integrated circuits, microelectromechanical systems, and optomechanical devices for traceable sensing and measurement applications. Many of these devices operate at microwave frequency and require characterization of their electrical and/or electro-optical frequency responses. As a result, a spectrum analyzer is needed to measure the electrical Fourier response and noise figure of micro- and nanofabricated devices, including microwave acoustic resonators and photonic modulators at frequencies up to 50 GHz.

II. Purpose

The spectrum analyzer is an electrical test instrument that will be used to measure the electrical output for microwave acoustic resonators and filters, photonic modulators, and other related devices, when driven by electrical and optical frequency sources, as well as when isolated from input signals. These measurements will be used to understand the resulting output power, noise sources, and nonlinearities of these devices, as well as to provide measurements for optimizing the electrical, mechanical, and optical device design. This instrument will support NIST’s mission-related research on wireless communications, AI computing, quantum metrology, and quantum information science.

III. Minimum Requirements

Contract Line Item 0001: Spectrum analyzer, Quantity 1

The spectrum analyzer shall meet or exceed the technical specifications listed below. All items must be new. Used or remanufactured equipment will not be considered for award. Experimental, prototype, or custom items will not be considered. The use of “gray market” components not authorized for sale in the U.S. by the proposer is not acceptable. All line items shall be shipped in the original manufacturer’s packaging and include all original documentation and software, when applicable.

Technical Specifications:

The spectrum analyzer must have the following specifications:

Instrument Functionality

1. The spectrum analyzer (SA) must be able to measure the frequency content of a single RF signal and process these results to generate related measurements.

2. The SA must have a color display (12” diagonally or larger) for visualizing all measurements and a front panel for operating the instrument.

3. The SA must be able to measure the phase noise of a periodic signal in the frequency domain.

4. The SA must have an internal hard disk drive for storing measurement data.

5. The SA must be calibrated prior to delivery using methods compliant with ANSI Z540

General Specifications

6. Minimum analysis frequency: 10 Hz or lower.

7. Maximum analysis frequency: 50 GHz or greater.

8. Phase noise (single sideband):

a) at 1 GHz, 1 kHz offset: -123 dBc/Hz or better

b) at 1 GHz, 1 MHz offset: -144 dBc/Hz or better

c) at 50 GHz, 1 kHz offset: -100 dBc/Hz or better

d) at 50 GHz, 1 MHz offset: -120 dBc/Hz or better

9. Displayed average noise level (DANL):

a) At 1 GHz: -150 dBm or better

b) At 50 GHz: -120 dBm or better

10. Maximum analysis bandwidth: 1.5 GHz or better.

11. Maximum safe input level: +30 dBm or higher.

12. Measured amplitude accuracy: +/- 0.5 dB or better.

13. Data acquisition sample rate: 100 MSamples/s or higher.

14. Data acquisition sampling resolution: 16 Bits.

15. The SA must operate on 110 – 120 VAC at 60 Hz and the power cable must be included.

IV. Deliverables:

Delivery shall be FOB destination and shall occur within 20 weeks after receipt of order. FOB Destination means: The contractor shall pack and mark the shipment in conformance with carrier requirements, deliver the shipment in good order and condition to the point of delivery specified in the purchase order, be responsible for any loss of and/or damage to the goods occurring before receipt and acceptance of the shipment by the consignee at the delivery point specified in the purchase order; and pay all charges to the specified point of delivery. The contractor shall deliver all Line Items to:

National Institute of Standards and Technology 100 Bureau Drive Gaithersburg, MD 20899-1640 V. Inspection and Acceptance

In addition to the inspection and acceptance terms articulated in 52.212-4, the Government reserves the right to perform such performance tests and evaluations as defined below to verify specified system performance. Such tests and evaluations, if performed, shall be conducted within the environment that the system is to be operated. The Contractor has the right to be present during the tests and evaluations, if performed, at the Contractor’s expense.

Acceptance test: The spectrum analyzer will be used to measure the output power and frequency of a microwave signal generator from 1 GHz to 50 GHz and compared to the

VI. Warranty

The contractor shall warrant the spectrum analyzer and provide support for a minimum of one year after receipt and shall be in accordance with terms in FAR 52.212-4.

VII. Payment Schedule

The Contractor shall be paid, in accordance with Net 30-day payment terms, upon receipt and acceptance of a proper invoice, in accordance with the following schedule:

1. 100% after receipt and acceptance by the TPOC of fully delivered software

2. The Government anticipates inspection will occur immediately upon download.

NOTE: Partial shipments and partial invoices will not be accepted, unless other-wise requested and accepted by the Contracting Officer prior to award offer. Proposed payment schedules shall be submitted with vendor’s response to the RFQ for consideration.