SOW -N30 Fire - Annual Service Air Compressor and Rescue Tools.docx

STATEMENT OF WORK

Annual service for the Eagle Air Compressor and Hurst eDraulic Rescue Tools

FY25-FY29

1. Performance Work Statement:

1.1 Description of Service: The contractor shall provide all qualified labor, tools, equipment, supplies, travel and shipping necessary to perform annual service for the Eagle Air Compressor, Hurst eDraulic Tools and Related Accessories. The contractor shall provide a written report of all maintenance performed, and note any recommended further corrective repairs.

1.2 Annual service for Eagle Air Compressor includes major maintenance program listed below on the following model and serial number:

· One (1) Eagle Harrier / Model: HA15M3C46-G525 / Serial No. 85447901

· One (1) Eagle Air / Model BHB10W3N2U / Serial No 235869301

· One (1) Eagle / Model: RVA20G3R4U / Serial No 55082401A

1.2.1 Change oil and oil filters as required.

1.2.2 Replace purification cartridges and O-ring, backup ring on chamber

1.2.3 Replace CO indicator kit (If applicable)

1.2.4 Check interstage pressure gauges and safety valves. Inspect final safety valve.

1.2.5 Inspect automatic condensate drain and rebuild per manufacturers specifications.

1.2.6 Inspect/clean separators as required.

1.2.7 Inspect lines/hoses, electrical cables, and air lines.

1.2.8 Inspect/replace air intake filter per manufacturers’ specifications.

1.2.9 Adjust pressure maintaining valve (PMV) to manufacturers’ specifications.

1.2.10 Inspect/rebuild air line check valves.

1.2.11 Lube electric motor as required and inspect/adjust belt tension and alignment.

1.2.12 Pressure test to final air pressure setting and adjust if required.

1.2.13 Inspect and clean inner coolers and after coolers as necessary.

1.2.14 Adjust automatic fill door interlock as necessary.

1.2.15 Adjust final air and oil switches as necessary.

1.2.16 Run and test compressor.

1.2.17 Provide Trace Analytics air sample test.

1.2.18 Complete maintenance checklist available at the completion of service.

1.2.19 Perform any additional factory recommendations/requirements.

1.3 Conduct annual service for Hurst eDraulic tools as follows;

· Two (2) Cutters

· Two (2) Spreaders

· One (1) StrongArm

1.3.1 Visual inspection of tools

1.3.2 Inspect arms/tips/blades for wear & damage

1.3.3 Inspect shaft seal & piston rod

1.3.4 Inspect control valve

1.3.5 Operate tool and observe speeds

1.3.6 Remove pivot pins, link arms and blades; clean & lube

1.3.7 Replace decals as required

1.3.8 Torque main bolt to spec

1.4 Annual Service for Hurst eDraulic Ram (2nos.)

1.4.1 Visual inspection of tool

1.4.2 Operate tool and observe speeds

1.4.3 Inspect shaft seal and piston

1.4.4 Check lights for proper operation

1.4.5 Replace decals as required

1.4.6 Inspect ram extension kit

1.5 Annual Check on the available accessories listed below;

· 01nos - StrongArm Charger

· 02nos - StrongArm Batteries

· 02nos – Tools charger

· 12nos – Batteries for Spreader, Cutter and Ram

1.5.1 Visual inspection of units

1.5.6 Check lights for proper operation

2. Servicing Requirements:

2.1 Contractor shall bring all necessary tools and equipment to perform annual service for the tools and equipment listed above.

2.2 The contractor shall follow all applicable federal, Department of Defense and Navy environmental regulations to include local supplements.

2.3 The contractor shall perform services at the NSA Bahrain Fire Stations and will coordinate with the Technical POC for base access. The contractor will be accompanied by government personnel while on base.

2.4 The contractor is responsible in providing a certified technician that has specialized skills and knowledge in servicing the above mentioned tools and equipment.

2.5 Contractor need to follow the Original Manufacturer’s guidelines as the equipment and tools are manufactured to meet all federal safety standards and requirements.

2.6 The contractor will provide a verbal outbrief to the Fire Chief or designee relaying the maintenance performed, observations as to working condition of the equipment and tools listed herein

2.7 Contractor shall provide a written site visit report within 30days indicating the certification of the maintenance work performed, any observations noted, and any recommendations for corrective maintenance.

3. Government Point of Contact:

Shihab Kurikkalakath Contract Specialist NAVSUP FLC Bahrain Commercial ☎: +973-1785-4729

DSN ☎: 318-439-4729

Email: shihab.kurikkalakath.ln@us.navy.mil

Period of Performance