SOW.docx

STATEMENT OF WORK

REPLACEMENT AND INITIAL ISSUANCE OF HONEYWELL MORNING PRIDE® FIREFIGHTER TURNOUTS WITH NAMEPLATES

1.0 Background: Commander Navy Region South West (CNRSW) Fire and Emergency Services (F&ES) is in need of continuous supply of customized Honeywell Morning Pride® firefighter turnouts Personal Protective Equipment (PPE) for replenishing inventory as result of retired unusable gear, and for provisioning newly hired firefighters. Requirement is for support of Federal Fire Departments located in United States (U.S.) Navy facilities in China Lake, San Diego, El Centro, Lemoore, Monterey, Seal Beach, and Point Mugu California, and Fallon Nevada. CNRSW F&ES current inventory of turnout PPE are Honeywell Morning Pride® brand for both structural and proximity tails and pants. Honeywell Morning Pride turnout gear is interchangeable, this allows for immediate replacement of the damaged area vice a full replacement of the entire piece of gear. Firefighter turnout gear must be replaced every ten (10) years or if the gear is damaged and no longer meets the NFPA standards.

2.0 Applicable Documents:

1. National Fire Protection Association (NFPA) - NFPA 19711500, 1851

2. Occupational Safety and Health Administration (OSHA) - OSHA 29 CFR Part 1910.132

3. Department of Defense Instruction 6055.1 – DoD Safety and Occupational Health (SOH)

3.0 Scope of work: The contractor shall supply personal protective equipment for a one-time contract for 80 coats and 80 pants. The cost for each shall include Fire Fighter nameplates and FEDFIRE station nameplates. CNRSW F&ES intends through this procurement, to provide the intial and replacement firefighter turnout gear required to support the mission. The cost of the turnout coats and the pants shall include Fire Fighter nameplates and FEDFIRE station nameplates. Names and location of individual Fire Fighters to receive turnouts shall be supplied to the contractor after award.

4.0 Deliverables:

4.1 PPE turnouts are customized to the specific Firefighter needs (i.e. type – structural; tail or pants; size; and quantity). The exact requirement cannot be predetermined at the time of contract award, and therefore, a single Indefinite Delivery – Requirements contract type will be used. It is anticipated that the Contractor shall provide customized Honeywell Morning Pride® turnouts PPE with the type, size, and quantity as specified by designated Ordering Officers (OO).

4.2 NAME PLATE CHARACTERISTICS: CUSTOM VELCRO PLATES – ALL LETTERING TO BE SILVER WITH BLACK OUTLINE –

4.2.1 “FEDERAL FIRE” IDENTIFYER PANEL:

A. Top Velcro panel with 2 rows of lettering to be silver with black outline-

1. Top row in 3 inch letters to read: “FEDERAL”

2. 2nd row in 2 inch letters to read: “FIRE”

4.2.2 VELCRO “FIRE FIGHTER NAME” PANELS FOR COAT/TAILS -

A. Panels to have firefighter name in 2 inch letters for tails of gear - lettering to be silver with black outline B. Fire fighter names shall be provided when each order is placed

4.3 PRODUCT REQUIRED:

Item Description

Quantity Unit of Measurement

“FEDERAL FIRE” IDENTIFYER PANEL: Top Velcro panel with 2 rows of lettering to be silver with black outline-Top row in 3 inch letters to read: “FEDERAL” & 2nd row in 2 inch letters to read:

“FIRE” - lettering to be silver with black outline

EACH

VELCRO “FIRE FIGHTER NAME” PANELS FOR

COAT/TAILS -Panels to have firefighter name in 2 inch letters for tails of gear - lettering to be silver with black outline

EACH

Table 1 - Honeywell Morning Pride® Turnout Schedule

CLIN

ITEM DESCRIPTION

UNIT

EST. QTY*

STRUCTURAL COAT - LTO-34B3 TAILS GOLD CNRSW – TO INCLUDE NAMEPLATES

EA

STRUCTURAL PANTS - LTO-34B3 PANTS GOLD CNRSW – TO INCLUDE NAMEPLATES

EA

5.0 Period of Performance: 26 August 2022 to 25 August 2023

Specifications: See Tables 2 below:

Table 2 –Structural Turnout Specifications

STRUCTURAL TURNOUT

Specifications - Honeywell Morning Pride® Structural Coat and Pant

Closure Systems:

Standard Coat Features

· Kinetic Kut™ Styling Significantly reduces hem rise and sleeve retraction, allowing for greater range of motion and protection, patented

· TAILS™ System Reduces weight, increases range of motion and eliminates bunching when bending forward

· Forward Flex™ Sleeve Patented design eliminates undesirable sleeve retraction when reaching up or forward

· Three-piece Coat Pattern Throughout All Layers Allows greater reach, flexibility, mobility, and protection while also dramatically improving the garment’s durability through years of use.

· Double-felled Stitched Major Seams on all Three Layers Increases durability

· Articulating Drag Rescue Device Adjusts to maintain equal leverage on a downed firefighter even when pulling from an angle, patented

· Comfortable Chinstraps Curved design for better fit and less irritation

· Dead Air Thermal Enhancement Panels Patented engineered thermal padding provides higher heat protection in specified areas

· Single Seam Sleeves Innovative design eliminates second seam, reducing wear point

· Waterproof Wristlets Double-layer Nomex® wristlets with continuous moisture barrier provide a liquid seal at the wrist, patented

· Long Tabbed Wristlets Patented durable and comfortable thumb locator option doesn’t interfere with glove donning

· Inspection Ports Patented feature allow for easier inspection of thermal liner and moisture barrier

Standard Pant Features

· Full Range of Motion Crotch Patented U-shape design and diamond-shaped insert allow greater leg mobility

· Low-waist Comfort Pant Increases mobility at waist, reduces weight, and allows for more ventilation

1. feels like a pair of jeans

2. wears like a pair of jeans

3. rides like a pair of jeans

· Postman Take-up Straps Adjustable to provide a better, tailored fit (option on pants, standard on coats)

· Knee Protection Patented Bi-Flex Heat Channel knees provide the highest level of comfort and protection available

· Reinforcements Sleeves, cuffs, and pockets can be reinforced with abrasion-resistant materials to meet department specifications

· Seam Guards Placed over trim threads at high-abrasion areas to reduce wear, patented

Additional Features

· Continuous Protection Outer shell, moisture barrier, and thermal barrier overlap at coat facings, collar linings, and pant fly to give uninterrupted protection

· Custom Sizing Five custom alteration measurements, three additional when needed, are taken to for a true custom fit

· Built-in 360° protection at coat facings

· All breathable construction (excluding trim, hardware and labels)

· Double-thickness, exterior-mounted storm shields

· Hang-up loop with 80 lb hang strength

· Button suspender attachments

· Options Attached with Lock Stitching

· Advanced Protective Tracking

· Barcoded for simplified NFPA 1851 tracking requirements

Certification – NFPA 1971

Standard Pant Features

· Full Range of Motion Crotch Patented U-shape design and diamond-shaped insert allow greater leg mobility

· Low-waist Comfort Pant Increases mobility at waist, reduces weight, and allows for more ventilation

1. feels like a pair of jeans

2. wears like a pair of jeans

3. rides like a pair of jeans

· Postman Take-up Straps Adjustable to provide a better, tailored fit (option on pants, standard on coats)

· Knee Protection Patented Bi-Flex Heat Channel knees provide the highest level of comfort and protection available

· Reinforcements Sleeves, cuffs, and pockets can be reinforced with abrasion-resistant materials to meet department specifications

Additional Features

· Continuous Protection Outer shell, moisture barrier, and thermal barrier overlap at coat facings, collar linings, and pant fly to give uninterrupted protection

· Custom Sizing Five custom alteration measurements, three additional when needed, are taken to for a true custom fit

· Built-in 360° protection at coat facings

· All breathable construction (excluding trim, hardware and labels)

· Double-thickness, exterior-mounted storm shields

· Hang-up loop with 80 lb hang strength

· Button suspender attachments

· Options Attached with Lock Stitching

· Advanced Protective Tracking

· Barcoded for simplified NFPA 1851 tracking requirements

Certification – NFPA 1971

Coat Part # Specifications:

LTOTOS36D - LTO Tail Outer Shell -7.2 osy Advance Soft -Gold LTOTTLB - LTO Tail Thermal Liner -7.4 osy Glide Ice 2 Layer LTOTMB3 - LTO Tail Moisture Barrier -4.7 osy Type 2F Crosstech Black CCSTD-36D - (Q01) Std -LTO Chinstrap CCVL-004 - Sub Storage Velcro for 2x2 Hook Velcro Follow Note for PlaB - Place on underside of chinstrap at stitch line

CFCCS-36D - Std -Coat Cuffs

IPLC (O20) - Std -Inspection Port Liner LBPF - Project Fires Label LNDC - Std-Liner detachable

LNSETTE - Std -SET Thermal Enhancement PKTLSTD - Std -Liner Label Pocket RS-RRSAC - (R01) Std-Articulating Rapid Rescue Strap RS-RRS-V - Velcro on Handle of Strap TR-DSS - Std -Trim Double-Stitched

TRC303M-TL - Trim -(3) NFPA Combo -lime 2-tone Scotchlite (3") **Tail Trim to Wrap Underside** **Move Vertical Bands As Close to Sleeve Seam As Possible**

LTBACKVO - Velcro Only for Back Patch * Square - Size to be 7" x 15 3/4" LTHEMVO - Velcro Only for Hem Patch CLZV2-36D - (E10) 2" Velcro/Zipper Coat Closure CL-03 (S04) - Shield - Full Length CL-TAB - pull tab - Arashield - Black CC4C - (Q04) 4" Collar and Chinstrap LN05 - (S03) Liner within 1" of Hem LNDAPC - (O50) Dead Air Panels RNSC-36D - (M04) Shoulder Caps -Advance Soft - Gold SATU-NONE - Delete Standard Take Up Straps PKAMLARD-36D - LA Air Mask/ Radio Pkt ComboAdvance Soft – Gold - Radio Pocket Size to be 8" x 3.5" x 2" --right chest

PKAMLARD-FNL - Notch Flap - Left

PKFSV-36D - Flashlight Strap Only w/Velcro - Advance Soft – Gold - Strap to be 1.5" x 11.5" with 3" of Velcro at each ends - Directly below chest trim & as close to leading edge as possible, but not under shield - " X " Box to be 2" --left side

PKFC-VLDS - Double-Stitched Velcro on Flashlight Strap

PKFSV-36D - Flashlight Strap Only w/Velcro - Advance Soft - Gold- Strap to be 1.5" x 11.5" with bartack 2" apart and with 3" of Velcro at each ends - Place Velcro 1/2" over from ends - Place directly above the trim on the LA Air Mask Pocket --right chest PKFC-VLDS - Double-Stitched Velcro on Flashlight Strap PKHBLNX-36D - X-Large Half Hi Bellows Pockets -Advance Soft - Gold 6 X 10 X 2

- Velcro on poocket flap to stop 1/2" from bottom edge of flap - Hook and Pile Velcro to have corners at a 45 degree angle on pocket – Angle flap corners - Pockets to be 1/2" above bottom of hem

PKRCFF-KV - Full Kevlar Lined

PKBLC-DSV - Double-Stitched Velcro on Pockets & Flaps

PKTO-KV - CA Tool Organizer – Kevlar - Place in left bellows pocket PKTO-DE - Delete Elastic in CA Tool Organizer PKBLC-V1 - 3 Vertical Strips Velcro on Flap/Full Velcro on Pocket

PKBLC-WHS - 2 Snaps on each Bellows Pocket Flaps - w/Velcro - Place 1 snap 2.5" from each side of flap

PKMT-36D - Mic Tab -Advance Soft - Gold 0.5 x 2 - Placed on the radio pocket directly above chest trim --left chest

PKMT-36D - Mic Tab -Advance Soft - Gold 0.5 x 2 - Place 1" above radio pocket flap--left chest

PKMT-36D - Mic Tab -Advance Soft - Gold 0.5 x 1.5 - Place directly above chest trim & as close to leading edge as possible, but not under shield --left chest

PKRD-36D - Radio Pocket -Advance Soft - Gold 8 x 3.5 x 2 - Velcro on pocket to be 1.5" X 2.5" placed vertical - Velcro on pocket flap to stop 1/2" from bottom edge of flap - Hook and Pile Velcro to have corners at a 45 degree angle on pocket - Angle Flap Corners - Flap to Fit Inside Dimension of Pocket - Flap to be 7.5" Long - Delete Lining of Radio Pocket - Raw Edges are Ok --left chest

PKRD-FNL - Notch Flap -Left

PKRD-DSV - Double-Stitch Velcro on Radio Pocket

PKRD-HS1 - Snap on Radio Pocket Flap -w/Velcro - Place 2 male snaps on pocket - Place 1 female snap on flap HWC02-AR - (S10) - 2 additional snap tabs on Bottom of Tail HWC03-AR - (S11) 2 Extra Snap Tabs Each Sleeve

HWCS2-AR (S09) - 2 additional snap tabs, one on each side seam

OPCN - ***CONSTRUCTION NOTE*** - **Must have 2" of Empty Space Above Bellows Pocket ** *TRIM HOOK AND PILE VELCRO AT CORNERS AT A 45 DEGREE ANGLE *

OPHL (S12) - ***Move Std Hang-Up Loop to Exterior *** OPLN - *** MP Logo Note *** - Place on LA air mask pocket WWSTLN - (W53) Sub Wristlets -Long with tabs –Nomex Pant Part # Specifications:

LTOPOS36D - LTO Pant Outer Shell -7.2 osy Advance Soft - Gold LTOPTLB - LTO Pant Thermal Liner -7.4 osy Glide Ice 2 Layer LTOPMB3 - LTO Pant Moisture Barrier -4.7 osy Type 2F Crosstech Black CFPCS-36D - Std Pants Cuffs -Advance Soft – Gold

IPLP - (O21) Std -Inspection Port Liner LBPFP - Project Fires Label LNDP - Std -Liner Detachable

TR-DSSP - Std -Trim Double-Stitched

TRP307M-TL - Trim -(7) NFPA -lime 2-tone Scotchlite (3")

CLW2RCT-36D - (J16) Wide Fly - 2" Velcro w/ Reverse Hook on Tab Closure CL2SLOW - (S27) 2 Snaps Added to Fly KNHCR-36D - Heat Channel Knees Replaceable - Advance - Gold

SACFT-36D - Cuff Tighteners -7.2 Soft Advance Soft – Gold - Strap with single female snap to be 1" x 3.5" - Strap with male snap to be 1.5"x 9.75" - Male snaps placed at 3",4.5", 6.5" & 8.5 - Move 1" forward of inseam**

PKBLP-36D - Bellows Pockets -Pants -Advance Soft - Gold 7 x 5 x 2 - Velcro on pocket flap to stop 1/2" from bottom edge of flap - Trim Hook and Pile Velcro on cornes at a 45 degree angle on pocket – Place 10" below top of waist on front of pants - Centered above the knees or as close to this position as possible ** DO NOT RAISE BELLOWS POCKETS TO ACCOMODATE THE BOOT ACCESS **

PKBLP-DSV - Double-stitched Velcro on bellows pockets PKBLP-WHS - 2 Snaps on each Bellows Pocket Flaps - w/Velcro - 1 Snap to be placed 1.5" from each side of flap - Angle flap corners

PKBLP-B4 - Bartack All 4 Corners of Bellows Pockets PKRPFF-KEV - Full Kevlar Lined PKHP2-36D - Hip Pocket (2) - Advance Soft - Gold 7 x 7 - Pockets to be 7" x 7" edge to edge - Place as close to center seam as possible - Parallel to waist - Flap directly above pocket - Pockets to have 6" of useable space - No lining - OK to have raw edges

PKHP-HS3 - 1 Snap on Each Hip Pocket -No Velcro

PKRD-36D - Radio Pocket -Advance Soft - Gold 7 x 3.5 x 2 - Velcro on pocket to be 1.5" X 2.5" placed vertical - Velcro on pocket flap to stop 1/2" from bottom edge of flap - Trim Hook and Pile Velcro on cornes at a 45 degree angle on pocket – Place 4" below top of Waist - Flap to be 7.5" Long - Angle flap corners - Flap to fit interior dimension of pocket - No Liner - OK to have raw edges --right side seam

PKRD-FNR - Notch Flap -Right

PKRD-DSV - Double-Stitch Velcro on Radio Pocket

PKRD-HS1 - Snap on Radio Pocket Flap -w/Velcro - Place 2 male snap on pocket - Place 1 female snap on flap HWC06 *** Hardware Note *** - Suspender button must be 2" center

OPBKV Belt - Kevlar with Quick Release Buckle

OPBL07 Belt Loops (7) - Place directly below waist band - Place 1 on back seam - Place 1 each aligned with outer edge of hip pocket - Place 1 on each side seam - Place 1 centered on left front - Place 1 left front next to fly seam - NO loops on right front - OK to remove belt loops from right side seam on 34 waist & smaller

OPCN - ***CONSTRUCTION NOTE*** **TRIM HOOK AND PILE VELCRO ON CORNERS AT A 45 DEGREE ANGLE **

SPDFQI - Dyna-Fit Suspenders w/ Quick Adjust Installed SPP - Suspender Padding BIBAP-36D - Boot Access Panels **USE LONGEST ZIPPER POSSIBLE**

Place of performance/delivery. Delivery of ordered item/s shall be made within sixty (60) days after receipt of order (ARO).

Period of Performance: This is a one-time order for 80 sets

Invoicing and payment instructions:

Contract type: This is a Fixed Firm Price contract – requirement supply type contract.

Equipment condition: New equipment only; NO remanufactured, refurbished, or “gray market” items. All items must be covered by the manufacturer’s warranty.

Payment and Invoicing:

Payment shall be made through WAWF as stated in Contract Terms and Conditions.

The Contractor shall submit an electronic invoice to the COR and the Financial POC. An invoice must include the following information:

· Name and address of the Contractor;

· Invoice date and number;

· Contract number, contract line item number and, if applicable, the order number;

· Description, quantity, unit of measure, unit price and extended price of the items delivered;

· Shipping number and date of shipment, including the bill of lading number and weight of shipment if shipped on Government bill of lading;

· Terms of any discount for prompt payment offered;

· Name and address of official to whom payment is to be sent;

· Name, title, and phone number of person to notify in event of defective invoice