1.02 PPE Minimum salient characteristics.docx

Must meet all safety requirements:

1. National Fire Protection Association (NFPA) - NFPA 19711500, 1851

2. Occupational Safety and Health Administration (OSHA) - OSHA 29 CFR Part 1910.132

3. Department of Defense Instruction 6055.1 – DoD Safety and Occupational Health (SOH)

Minimum salient characteristics:

Coat Part # Specifications:

LTOTOS36D - LTO Tail Outer Shell -7.2 osy Advance Soft -Gold

LTOTTLB - LTO Tail Thermal Liner -7.4 osy Glide Ice 2 Layer

LTOTMB3 - LTO Tail Moisture Barrier -4.7 osy Type 2F Crosstech Black

CCSTD-36D - (Q01) Std -LTO Chinstrap

CCVL-004 - Sub Storage Velcro for 2x2 Hook Velcro Follow Note for PlaB - Place on underside of chinstrap at stitch line

CFCCS-36D - Std -Coat Cuffs

IPLC (O20) - Std -Inspection Port Liner

LBPF - Project Fires Label

LNDC - Std-Liner detachable

LNSETTE - Std -SET Thermal Enhancement

PKTLSTD - Std -Liner Label Pocket

RS-RRSAC - (R01) Std-Articulating Rapid Rescue Strap

RS-RRS-V - Velcro on Handle of Strap

TR-DSS - Std -Trim Double-Stitched

TRC303M-TL - Trim -(3) NFPA Combo -lime 2-tone Scotchlite (3") **Tail Trim to Wrap Underside** **Move Vertical Bands As Close to Sleeve Seam As Possible**

LTBACKVO - Velcro Only for Back Patch * Square - Size to be 7" x 15 3/4"

LTHEMVO - Velcro Only for Hem Patch

CLZV2-36D - (E10) 2" Velcro/Zipper Coat Closure

CL-03 (S04) - Shield - Full Length

CL-TAB - pull tab - Arashield - Black

CC4C - (Q04) 4" Collar and Chinstrap

LN05 - (S03) Liner within 1" of Hem

LNDAPC - (O50) Dead Air Panels

RNSC-36D - (M04) Shoulder Caps -Advance Soft - Gold

SATU-NONE - Delete Standard Take Up Straps

PKAMLARD-36D - LA Air Mask/ Radio Pkt ComboAdvance Soft – Gold - Radio Pocket Size to be 8" x 3.5" x 2" --right chest

PKAMLARD-FNL - Notch Flap - Left

PKFSV-36D - Flashlight Strap Only w/Velcro - Advance Soft – Gold - Strap to be 1.5" x 11.5" with 3" of Velcro at each ends - Directly below chest trim & as close to leading edge as possible, but not under shield - " X " Box to be 2" --left side

PKFC-VLDS - Double-Stitched Velcro on Flashlight Strap

PKFSV-36D - Flashlight Strap Only w/Velcro - Advance Soft - Gold- Strap to be 1.5" x 11.5" with bartack 2" apart and with 3" of Velcro at each ends - Place Velcro 1/2" over from ends - Place directly above the trim on the LA Air Mask Pocket --right chest

PKFC-VLDS - Double-Stitched Velcro on Flashlight Strap

PKHBLNX-36D - X-Large Half Hi Bellows Pockets -Advance Soft - Gold 6 X 10 X 2

- Velcro on poocket flap to stop 1/2" from bottom edge of flap - Hook and Pile Velcro to have corners at a 45 degree angle on pocket – Angle flap corners - Pockets to be 1/2" above bottom of hem

PKRCFF-KV - Full Kevlar Lined

PKBLC-DSV - Double-Stitched Velcro on Pockets & Flaps

PKTO-KV - CA Tool Organizer – Kevlar - Place in left bellows pocket

PKTO-DE - Delete Elastic in CA Tool Organizer

PKBLC-V1 - 3 Vertical Strips Velcro on Flap/Full Velcro on Pocket

PKBLC-WHS - 2 Snaps on each Bellows Pocket Flaps - w/Velcro - Place 1 snap 2.5" from each side of flap

PKMT-36D - Mic Tab -Advance Soft - Gold 0.5 x 2 - Placed on the radio pocket directly above chest trim --left chest

PKMT-36D - Mic Tab -Advance Soft - Gold 0.5 x 2 - Place 1" above radio pocket flap--left chest

PKMT-36D - Mic Tab -Advance Soft - Gold 0.5 x 1.5 - Place directly above chest trim & as close to leading edge as possible, but not under shield --left chest

PKRD-36D - Radio Pocket -Advance Soft - Gold 8 x 3.5 x 2 - Velcro on pocket to be 1.5" X 2.5" placed vertical - Velcro on pocket flap to stop 1/2" from bottom edge of flap - Hook and Pile Velcro to have corners at a 45 degree angle on pocket - Angle Flap Corners - Flap to Fit Inside Dimension of Pocket - Flap to be 7.5" Long - Delete Lining of Radio Pocket - Raw Edges are Ok --left chest

PKRD-FNL - Notch Flap -Left

PKRD-DSV - Double-Stitch Velcro on Radio Pocket

PKRD-HS1 - Snap on Radio Pocket Flap -w/Velcro - Place 2 male snaps on pocket - Place 1 female snap on flap

HWC02-AR - (S10) - 2 additional snap tabs on Bottom of Tail

HWC03-AR - (S11) 2 Extra Snap Tabs Each Sleeve

HWCS2-AR (S09) - 2 additional snap tabs, one on each side seam

OPCN - ***CONSTRUCTION NOTE*** - **Must have 2" of Empty Space Above Bellows Pocket ** *TRIM HOOK AND PILE VELCRO AT CORNERS AT A 45 DEGREE ANGLE *

OPHL (S12) - ***Move Std Hang-Up Loop to Exterior ***

OPLN - *** MP Logo Note *** - Place on LA air mask pocket

WWSTLN - (W53) Sub Wristlets -Long with tabs –Nomex

Pant Part # Specifications:

LTOPOS36D - LTO Pant Outer Shell -7.2 osy Advance Soft - Gold

LTOPTLB - LTO Pant Thermal Liner -7.4 osy Glide Ice 2 Layer

LTOPMB3 - LTO Pant Moisture Barrier -4.7 osy Type 2F Crosstech Black

CFPCS-36D - Std Pants Cuffs -Advance Soft – Gold

IPLP - (O21) Std -Inspection Port Liner

LBPFP - Project Fires Label

LNDP - Std -Liner Detachable

TR-DSSP - Std -Trim Double-Stitched

TRP307M-TL - Trim -(7) NFPA -lime 2-tone Scotchlite (3")

CLW2RCT-36D - (J16) Wide Fly - 2" Velcro w/ Reverse Hook on Tab Closure

CL2SLOW - (S27) 2 Snaps Added to Fly

KNHCR-36D - Heat Channel Knees Replaceable - Advance - Gold

SACFT-36D - Cuff Tighteners -7.2 Soft Advance Soft – Gold - Strap with single female snap to be 1" x 3.5" - Strap with male snap to be 1.5"x 9.75" - Male snaps placed at 3",4.5", 6.5" & 8.5 - Move 1" forward of inseam**

PKBLP-36D - Bellows Pockets -Pants -Advance Soft - Gold 7 x 5 x 2 - Velcro on pocket flap to stop 1/2" from bottom edge of flap - Trim Hook and Pile Velcro on cornes at a 45 degree angle on pocket – Place 10" below top of waist on front of pants - Centered above the knees or as close to this position as possible ** DO NOT RAISE BELLOWS POCKETS TO ACCOMODATE THE BOOT ACCESS **

PKBLP-DSV - Double-stitched Velcro on bellows pockets PKBLP-WHS - 2 Snaps on each Bellows Pocket Flaps - w/Velcro - 1 Snap to be placed 1.5" from each side of flap - Angle flap corners

PKBLP-B4 - Bartack All 4 Corners of Bellows Pockets

PKRPFF-KEV - Full Kevlar Lined

PKHP2-36D - Hip Pocket (2) - Advance Soft - Gold 7 x 7 - Pockets to be 7" x 7" edge to edge - Place as close to center seam as possible - Parallel to waist - Flap directly above pocket - Pockets to have 6" of useable space - No lining - OK to have raw edges

PKHP-HS3 - 1 Snap on Each Hip Pocket -No Velcro

PKRD-36D - Radio Pocket -Advance Soft - Gold 7 x 3.5 x 2 - Velcro on pocket to be 1.5" X 2.5" placed vertical - Velcro on pocket flap to stop 1/2" from bottom edge of flap - Trim Hook and Pile Velcro on cornes at a 45 degree angle on pocket – Place 4" below top of Waist - Flap to be 7.5" Long - Angle flap corners - Flap to fit interior dimension of pocket - No Liner - OK to have raw edges --right side seam

PKRD-FNR - Notch Flap -Right

PKRD-DSV - Double-Stitch Velcro on Radio Pocket

PKRD-HS1 - Snap on Radio Pocket Flap -w/Velcro - Place 2 male snap on pocket - Place 1 female snap on flap HWC06 *** Hardware Note *** - Suspender button must be 2" center

OPBKV Belt - Kevlar with Quick Release Buckle

OPBL07 Belt Loops (7) - Place directly below waist band - Place 1 on back seam - Place 1 each aligned with outer edge of hip pocket - Place 1 on each side seam - Place 1 centered on left front - Place 1 left front next to fly seam - NO loops on right front - OK to remove belt loops from right side seam on 34 waist & smaller

OPCN - ***CONSTRUCTION NOTE*** **TRIM HOOK AND PILE VELCRO ON CORNERS AT A 45 DEGREE ANGLE **

SPDFQI - Dyna-Fit Suspenders w/ Quick Adjust Installed

SPP - Suspender Padding

BIBAP-36D - Boot Access Panels **USE LONGEST ZIPPER POSSIBLE**