Sol_140D8021R0001.pdf

SEE ADDENDUMIS CHECKED

CODE 18a. PAYMENT WILL BE MADE BY

CODE

FACILITYCODE

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER

OFFEROR

D47

Boise ID 83706 300 E. Mallard Dr., Suite 200 Division 4/ Branch 4 Interior Business Center, AQD

CODE 16. ADMINISTERED BYCODE

X

X

X

481211

SIZE STANDARD:

100.00 % FOR:SET ASIDE:UNRESTRICTED ORD47

RFPIFB

10. THIS ACQUISITION ISCODE

RFQ

14. METHOD OF SOLICITATION

13b. RATING

NAICS:

SMALL BUSINESS

01/08/2021 1200 MT

12/09/2020

0000000000Maile Nichols (No collect calls)

INFORMATION CALL:

FOR SOLICITATION 8. OFFER DUE DATE/LOCAL TIMEb. TELEPHONE NUMBER a. NAME

4. ORDER NUMBER3. AWARD/ 6. SOLICITATION

140D8021R0001

5. SOLICITATION NUMBER

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS 1. REQUISITION NUMBER PAGE OF

1 94 OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30

TELEPHONE NO.

17a. CONTRACTOR/ maile_nichols@ibc.doi.gov

15. DELIVER TO

Boise ID 83706 300 E. Mallard Dr., Suite 200 Division 4/ Branch 4

9. ISSUED BY

7.

2. CONTRACT NO.

EFFECTIVE DATE

1,500

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW

ISSUE DATE

DELIVERY FOR FOB DESTINA-

TION UNLESS BLOCK IS

MARKED

11.

SEE SCHEDULEX

12. DISCOUNT TERMS

THIS CONTRACT IS A

RATED ORDER UNDER

DPAS (15 CFR 700)

13a.

SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

HUBZONE SMALL

BUSINESS

8(A)

Interior Business Center, AQD

WOMEN-OWNED SMALL BUSINESS

(WOSB) ELIGIBLE UNDER THE WOMEN-OWNED

SMALL BUSINESS PROGRAM

EDWOSB

24.

AMOUNT

23.

UNIT PRICE

22.

UNIT

21.

QUANTITY

20.

SCHEDULE OF SUPPLIES/SERVICES

19.

ITEM NO.

00010 Exclusive Use Type III Helicopter Services - Whiteriver, AZ

00020 Exclusive Use Type III Helicopter Services - Window Rock, AZ

(Use Reverse and/or Attach Additional Sheets as Necessary)

HEREIN, IS ACCEPTED AS TO ITEMS:

DATED

Austin Carter

. YOUR OFFER ON SOLICITATION (BLOCK 5),

INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET FORTH

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DELIVER

ARE

ARE

31c. DATE SIGNED

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA

31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)

30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (Type or print)

ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY ADDITIONAL

SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED.

27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 AND 52.212-5 ARE ATTACHED. ADDENDA

26. TOTAL AWARD AMOUNT (For Govt. Use Only)

OFFER

STANDARD FORM 1449 (REV. 2/2012)

Prescribed by GSA - FAR (48 CFR) 53.212

ARE NOT ATTACHED.

ARE NOT ATTACHED.

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

30b. NAME AND TITLE OF SIGNER (Type or print)

30a. SIGNATURE OF OFFEROR/CONTRACTOR

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN

25. ACCOUNTING AND APPROPRIATION DATA

29. AWARD OF CONTRACT:

REF.

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32c. DATE 32b. SIGNATURE OF AUTHORIZED GOVERNMENT REPRESENTATIVE

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED:

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED

40. PAID BY39. S/R VOUCHER NUMBER38. S/R ACCOUNT NUMBER

37. CHECK NUMBER

FINALPARTIAL

36. PAYMENT

FINALPARTIAL

35. AMOUNT VERIFIED

CORRECT FOR

34. VOUCHER NUMBER33. SHIP NUMBER

COMPLETE

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

42d. TOTAL CONTAINERS42c. DATE REC'D (YY/MM/DD)

42b. RECEIVED AT (Location)

42a. RECEIVED BY (Print)

41c. DATE41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

STANDARD FORM 1449 (REV. 2/2012) BACK

24.

AMOUNT

23.

UNIT PRICE

22.

UNIT

21.

QUANTITY

20.

SCHEDULE OF SUPPLIES/SERVICES

19.

ITEM NO.

32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT REPRESENTATIVE

94 2 of

Exclusive Use Type III Helicopter Solicitation 140D8021R0001

Table of Contents

CONTRACT ACRONYMS

A1 SCHEDULE OF SUPPLIES/SERVICES

A1.1 ITEM 1: WHITE RIVER, AZ

A1.2 ITEM 2 WINDOW ROCK, AZ

A2 SCHEDULES OF SERVICES AND PRICES

A2.1 SCHEDULE FOR WHITERIVER, AZ

A2.2 SCHEDULE FOR WINDOW ROCK, AZ

SECTION B – TECHNICAL SPECIFICATIONS

GENERAL REQUIREMENTS

B1 SCOPE OF CONTRACT

B2 CERTIFICATIONS

B3 ORDER OF PRECEDENCE (SPECIFICATIONS)

B4 CONTRACTS

EQUIPMENT REQUIREMENTS

B5 CONDITION OF EQUIPMENT

B6 AIRCRAFT EQUIPMENT REQUIREMENTS

B7 AVIONICS REQUIREMENTS

B8 FUEL SERVICING VEHICLE EQUIPMENT REQUIREMENTS

(REQUIRED FOR LOWER 48 STATES OPERATIONS ONLY)

PERSONNEL REQUIREMENTS

B9 PILOT REQUIREMENTS AND AUTHORITY

B10 PILOT QUALIFICATIONS

B11 PERSONNEL DUTY LIMITATIONS

B12 FLIGHT CREWMEMBERS’ DUTY AND FLIGHT

LIMITATIONS

B13 MECHANIC REQUIREMENT

B14 MECHANIC QUALIFICATIONS

B15 MECHANIC DUTY LIMITATIONS

B16 FUEL SERVICING VEHICLE DRIVER REQUIREMENT AND

QUALIFICATIONS (REQUIRED FOR LOWER 48 STATES

OPERATIONS ONLY)

B17 FUEL SERVICING VEHICLE DRIVER DUTY LIMITATIONS

B18 RELIEF CREW REQUIREMENT

OPERATIONS

B19 PILOT AUTHORITY AND RESPONSIBILITY

B20 FLIGHT OPERATIONS

B21 SECURITY OF AIRCRAFT AND EQUIPMENT

B22 PERSONAL PROTECTIVE EQUIPMENT (PPE) FOR

FLIGHT OPERATIONS

B23 PPE FOR GROUND OPERATIONS

B24 TRANSPORTATION OF HAZARDOUS MATERIALS

B25 FUEL AND SERVICING REQUIREMENTS

AIRCRAFT MAINTENANCE REQUIREMENTS

B26 GENERAL - MAINTENANCE

B27 AIRWORTHINESS DIRECTIVES (AD’S) AND

MANUFACTURER’S MANDATORY SERVICE BULLETINS

(MMSB’S)

B28 MANUALS/RECORDS

B29 MAINTENANCE

B30 MAINTENANCE TEST FLIGHT

B31 TIME BETWEEN OVERHAUL (TBO) AND LIFE-LIMITED

PARTS

B32 WEIGHT AND BALANCE

B33 HELICOPTER TURBINE ENGINE POWER CHECK

SECTION C – CONTRACT TERMS AND

CONDITIONS

CONTRACT CLAUSES

52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB

1998)

CLAUSES INCORPORATED BY REFERENCE

CLAUSES INCORPORATED BY FULL TEXT

ADDENDA TO CONTRACT TERMS AND

CONDITIONS

52.212-4(A) INSPECTION/ACCEPTANCE

52.212-4(K) TAXES

52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED

TO IMPLEMENT STATUTES OR EXECUTIVE ORDERS-

COMMERCIAL ITEMS (NOV 2020)

52.216-18 ORDERING (AUG 2020)

52.216-19 ORDER LIMITATIONS (OCT 1995)

52.216-22 INDEFINITE QUANTITY (OCT 1995)

52.217-8 OPTION TO EXTEND SERVICES (NOV 1999)

52.222-42 STATEMENT OF EQUIVALENT RATES FOR

FEDERAL HIRES (MAY 2014)

1452.201-70 AUTHORITIES AND DELEGATIONS (SEPT 2011)

ADDENDA TO 1452.201-70 COTR/PI/SAFETY MANAGER &

ADVISOR CONTRACTING OFFICER'S TECHNICAL

REPRESENTATIVE (COTR)

DIAR 1452.228-71 AIRCRAFT AND GENERAL PUBLIC

LIABILITY INSURANCE (MAR 1989)

GENERAL CONTRACT TERMS AND CONDITIONS

C1 INVOICES - AIRCRAFT USE REPORTS (AUR)

C2 ELECTRONIC INVOICING AND PAYMENT REQUIREMENTS

– INVOICE PROCESSING PLATFORM (IPP) (APR 2013)

C3 CONTRACTOR PERSONNEL SECURITY REQUIREMENTS 42

C4 RESERVED

C5 RESERVED

C6 CONTRACTOR PERFORMANCE ASSESSMENT

REPORTING SYSTEM (DEC 2015)

C7 PREWORK MEETING

ADMINISTRATIVE MATTERS

C8 PERSONNEL CONDUCT

C9 SAFETY

C10 MISHAPS

C11 RESERVED

C12 ECONOMIC PRICE ADJUSTMENT – FUEL (LOWER 48

ONLY)

CONTRACT PERIOD AND RENEWAL

C13 CONTRACT PERIOD

C14 EXCLUSIVE USE PERIOD

C15 OPTIONAL EXTENSION OF EXCLUSIVE USE PERIOD .. 46

AVAILABILITY REQUIREMENTS

C16 AVAILABILITY REQUIREMENTS

C17 SCHEDULE OF OPERATIONS AND REACTION TIME

C18 MAINTENANCE DURING AVAILABILITY PERIOD

C19 UNAVAILABILITY AND DAMAGES

MEASUREMENT AND PAYMENT

C20 DAILY AVAILABILITY

C21 FLIGHT TIME

C22 MOBILIZATION/DEMOBILIZATION

C23 ADDITIONAL PAY ITEMS (FROM SCHEDULE OF ITEMS)

C24 GOVERNMENT MISCELLANEOUS CHARGES

C25 RESERVED

SECTION C EXHIBITS

SECTION D – INSTRUCTIONS TO OFFERORS AND

EVALUATION OF OFFERS

D1 GENERAL INFORMATION

D2 NORTH AMERICAN INDUSTRY CLASSIFICATION SYSTEM

(NAICS) CODE AND SMALL BUSINESS SIZE STANDARD ... 74

INSTRUCTIONS TO OFFERORS--COMMERCIAL

ITEMS (52.212-1 OCT 2018) TAILORED

D3 OFFERS

D4 OFFER CONTENTS

VOLUME IV, PAST PERFORMANCE

D5 PERIOD FOR ACCEPTANCE OF OFFERS

D6 LATE SUBMISSIONS, MODIFICATIONS, REVISIONS, AND

WITHDRAWALS OF OFFERS

D7 SPECIAL NOTICE TO OFFERORS

52.212-2 EVALUATION—COMMERCIAL ITEMS (OCT 2014)

(TAILORED)

D8 EVALUATION FACTORS

D9 TECHNICAL CAPABILITY

D10 ORGANIZATIONAL SAFETY

D11 PAST PERFORMANCE

D12 TOTAL EVALUATED PRICE

D13 TRADEOFF ANALYSIS AND CONTRACTOR SELECTION

D14 INQUIRIES REGARDING THE SOLICITATION

SECTION E – OFFEROR’S REPRESENTATIONS,

CERTIFICATIONS AND OTHER STATEMENTS

52.252-1 SOLICITATION PROVISIONS INCORPORATED BY

REFERENCE (FEB 1998)

52.204-24 REPRESENTATION REGARDING CERTAIN

TELECOMMUNICATIONS AND VIDEO SURVEILLANCE

SERVICES OR EQUIPMENT. (OCT 2020)

52.209-2 PROHIBITION ON CONTRACTING WITH INVERTED

DOMESTIC CORPORATIONS-REPRESENTATION (NOV 2015)

52.209-5 CERTIFICATION REGARDING RESPONSIBILITY

MATTERS. (AUG 2020)

52.209-7 INFORMATION REGARDING RESPONSIBILITY

MATTERS (OCT 2018)

52.209-11 – REPRESENTATION BY CORPORATIONS

REGARDING DELINQUENT TAX LIABILITY OR A FELONY

CONVICTION UNDER ANY FEDERAL LAW (FEB 2016)

FAR 52.212-3 OFFEROR REPRESENTATIONS AND

CERTIFICATIONS-COMMERCIAL ITEMS (OCT 2020)

52.216-1 TYPE OF CONTRACT (APR 1984)

DIAR 1452.233-2 SERVICE OF PROTEST DEPARTMENT OF

THE INTERIOR (JUL 1996) (DEVIATION)

DIAR 1452.215-71 USE AND DISCLOSURE OF PROPOSAL

INFORMATION (APR 1984)

SECTION E EXHIBITS

Contract Acronyms

AC Advisory Circular ACETA Aerial Capture Eradication and Tagging of Animals AD Airworthiness Directive AIRS Aviation Invoice Reporting Support application A&P airframe and power-plant APCO Association of Public-Safety Communications

Officials ASM Aviation Safety Manager ASO Aviation Safety Office ASTM American Society for Testing and Material ATC air traffic control AUR aircraft use report BIA Bureau of Indian Affairs CASTPE Chief, Aviation Safety, Training and Program

Evaluations CFR Code of Federal Regulations CO Contracting Officer COR Contracting Officer’s Representative COTR Contracting Officer’s Technical Representative CFR Code of Federal Regulations CTCSS continuous tone coded squelch system DM degrees/minutes/decimal minutes DOI Department of Interior DOT Department of Transportation ELT emergency locator transmitter EPA Environmental Protection Agency ERG Emergency Response Guidebook EU exclusive use FAA Federal Aviation Administration FAR Federal Acquisition Regulations FS Forest Service FTR Federal Travel Regulations GVW gross vehicle weight GPM gallons per minute GPS global positioning system HIGE hover-in-ground effect HOGEJ hover-out-of-ground effect, jettisonable IAT interagency aviation training ICAO International Civil Aviation Organization ICS intercom system IFR instrument flight rules IIC Investigator in Charge IP Institute of Petroleum IPP Invoice Processing Platform ISA International Standard Atmosphere MMSB Manufacturer’s Mandatory Service Bulletins NFPA National Fire Protection Association NTSB National Transportation Safety Board NWCG National Wildfire Coordinating Group OAS Office of Aviation Services PA public address system PFD personal flotation device PIC pilot-in-command PPE personal protective equipment PSD plastic sphere dispenser PSI pounds per square inch PTT push to talk RFP Request for Proposals RPM revolutions per minute

SFI Safety Foundation Incorporated STEP Single-skid, Toe-In and Hover Exit/Entry

Procedures TBO time between overhaul TERO Tribal Employment Rights Ordinances TSO technical service order UL Underwriter’s Laboratory USDA United States Department of Agriculture VFR visual flight rules VNE velocity never exceed VOX voice activation VSWR voltage standing wave ratio

SECTION A - REQUIREMENTS AND PRICES

A1 SCHEDULE OF SUPPLIES/SERVICES

The intent of this solicitation is to obtain fully Contractor operated and maintained exclusive use helicopter flight services using two (2) helicopters to report to two (2) different Bureau of Indian Affairs locations for 100 and 110 calendar days for Whiteriver, AZ and Window Rock, AZ, respectively. Pricing in Section A will be evaluated and used for both Designated Bases under separate contract awards.

A1.1 ITEM 1: White River, AZ

Designated Bases: Whiteriver, AZ

Exclusive Use Periods: May 15 through August 22 (100 Calendar days), five-year ordering period, from April 01, 2021 through March 31, 2026.

Aircraft Required: One (1) light helicopter equipped as specified in Section B

Fuel Service Vehicle (FSV): One (1) FSV meeting the requirements identified in Section B

Crew Compliment Required at each Designated Base: Pilot-in-Command (PIC), Fuel Servicing Vehicle Driver(s), Relief PIC, Relief Fuel

Servicing Vehicle Driver(s)

Minimum Helicopter Requirements:

Seating: Five (5) insured passenger seats not including pilot, but including copilot seat in an aircraft, normally single-pilot operated.

Payload: Non-jettisonable payload (HOGE) of 1,000 pounds at 25 degrees C at 7,000 feet pressure altitude using a pilot weight of 200 pounds, a 25-pound survival kit and fuel for 1.5 hours.

Powerplant: Turbine engine

Certification: 14 CFR 27

Airspeed: 130 knots VNE at 25 degrees C at 7,000 feet

(Payload amounts shall be computed by using the Government’s Standard Interagency Load Calculation Method and Form and the Helicopter Fuel Consumption and Weight Reduction Chart included under Section C Exhibits along with the offered aircraft’s applicable Hover Ceiling Charts, weight and balance report and equipment list that you provide).

A1.2 ITEM 2 Window Rock, AZ

Designated Bases: Window Rock, AZ

Exclusive Use Periods: May 01 through August 18 (110 Calendar days), five-year ordering period, from April 01, 2021 through March 31, 2026.

Aircraft Required: One light helicopter equipped as specified in Section B

Fuel Service Vehicle (FSV): One FSV meeting the requirements identified in Section B

Crew Compliment Required at each Designated Base: Pilot-in-Command (PIC), Fuel Servicing Vehicle Driver(s), Relief PIC, Relief Fuel

Servicing Vehicle Driver(s)

Minimum Helicopter Requirements:

Seating: Five (5) insured passenger seats not including pilot, but including copilot seat in an aircraft, normally single-pilot operated.

Payload: Non-jettisonable payload (HOGE) of 1,000 pounds at 25 degrees C at 7,000 feet pressure altitude using a pilot weight of 200 pounds, a 25-pound survival kit and fuel for 1.5 hours.

Powerplant: Turbine engine

Certification: 14 CFR 27

Airspeed: 130 knots VNE at 25 degrees C at 7,000 feet

(Payload amounts shall be computed by using the Government’s Standard Interagency Load Calculation Method and Form and the Helicopter Fuel Consumption and Weight Reduction Chart included under Section C Exhibits along with the offered aircraft’s applicable Hover Ceiling Charts, weight and balance report and equipment list that you provide).

A2.5 In the lower-48 states all fuel shall be provided by the contractor and should be included in the flight rate (wet rate).

A2.6 In Alaska, fuel will be furnished by the Government. All fuel not otherwise furnished by the Government must be purchased by or charged to the Contractor. The purchase must be approved by the Contracting Officer. Fuel related costs shall be recorded as a line entry (i.e., date, fuel charge, dollar amount, and use-item code fuel charge [FC]), shall be used and shall be supported by paid legible, itemized invoices from the supplier. Certified true copies may be submitted in lieu of the original invoice.

A2.7 Rates for flight hours must be in whole dollars. If the unit prices are adjusted during the life of the contract, they will be adjusted to a whole dollar as follows: amounts of 50 cents or less will be rounded down and amounts of 51 cents or more will be rounded up.

RATE SCHEDULE FOR ADDITIONAL PAY ITEMS (Time & Material IAW FAR 52.212-4, Alternate I) Note: The rates below are applicable for the entire five-year term of the contract.

ADDITIONAL PAY ITEM DESCRIPTIONS Pay Item Code

Quantity Unit Rates

Extended Standby – Pilot EP Indefinite Hour $ 62.00 Extended Standby – Driver Medium Truck Large Truck

ET Indefinite Hour

$ 40.00 $ 42.00

Fuel Servicing Vehicle Mileage SML Indefinite Mile 750-1,499 gal - $ 3.20 Subsistence Allowance (Per Diem) PD Indefinite Overnight Standard or High GSA Rate Special Charge for Miscellaneous Allowable Expenses SC Indefinite Each At Cost Fuel Charge (Alaska Only) FC Indefinite Gallons Actual Cost (See Exhibit 12)

SECTION B – TECHNICAL SPECIFICATIONS

SECTION B – TECHNICAL SPECIFICATIONS

GENERAL REQUIREMENTS

B1 Scope of Contract

B1.1 The intent of this contract is to obtain fully Contractor operated and maintained exclusive use helicopter flight services to transport personnel and/or cargo in support of Government natural resource missions. Contractor services include provision of a helicopter, personnel, fuel servicing vehicle, fuel, and all other associated equipment, as prescribed in this solicitation. Missions will include, but are not limited to, fire suppression, fire monitoring, initial attack, prescribed fire and aerial ignition, law enforcement limited to non-threatening surveillance and reconnaissance, and other administrative and related resource activities. The Government will direct aircraft to support its missions and objectives.

B1.2 During the exclusive use period and any subsequent extension, aircraft furnished shall be subject to the exclusive use and control of the Government 24 hours per day, 7 days per week.

B1.3 The Government and Contractor must establish an effective working relationship to successfully complete this contract. The Contractor’s employees’ cooperation, professionalism, and positive attitude toward aviation safety and accomplishment of the mission are an integral element of this relationship.

B1.4 The Government has interagency and cooperative agreements with other Federal and State agencies and private landholders and may dispatch aircraft under this contract for such cooperative use.

B1.5 This aircraft may be dispatched to Alaska. Because deployment to Alaska usually requires transit through Canada, all required contractor personnel must possess current passports. For the Alaska-specific equipment and/or operational requirements, refer to the Alaska Supplement Exhibit (see Section C).

B2 Certifications

The Contractor must hold and keep current all of the following required certificates and must ensure that contract aircraft are operated and maintained in compliance with those certificates at all times:

B2.1 A Federal Aviation Administration (FAA) Air Carrier or Operating Certificate which authorizes the Contractor to operate in the category and class of aircraft and under flight conditions required by this contract (e.g., rotorcraft, visual flight rules (VFR) day/night, passengers, and cargo) in the conterminous United States and Alaska.

B2.2 A Title 14 of the Code of Federal Regulations Part 135 (14 CFR 135) Air Carrier Certificate. These aircraft must be carried on the list required by 14 CFR 135.63 or Operations Specifications Part D, "Aircraft Listing," as appropriate.

B2.3 A 14 CFR 133, Rotorcraft External Load Operations Certificate which authorizes Class B loads, as a minimum.

B2.4 A 14 CFR 137, Agricultural Aircraft Operations Certificate.

B2.5 The contract aircraft must have a Standard Airworthiness Certificate. Installation of any equipment required by this contract must be FAA-approved.

B3 Order of Precedence (Specifications)

In the event of inconsistencies within the technical specification, the following order will be used in such resolution: (1) typed provisions of these specifications; (2) DOI Office of Aviation Services (OAS) supplements and/or exhibits incorporated by reference; (3) 14 CFR incorporated by reference; (4) aircraft manufacturer's specifications; (5) other documents incorporated by reference.

B4 Contracts

B4.1 The Contractor must maintain a complete, current copy of the contract, modifications, and task orders (if applicable) in each contract aircraft throughout the performance period.

B4.2 The pilot must have task order information (i.e. task number, performance period) in his/her possession prior to any flights under this contract and make this information available to government representatives on request.

B4.3 Electronic copies of contracts and task orders may be used. However, the contractor is responsible for ensuring that the documents are uploaded on an appropriate viewing device (e.g., laptop or tablet), which must be charged and made available at the aircraft for reference by government representatives upon request. Further, the contractor must agree to hold the government harmless for any inadvertent or accidental damage to the device.

EQUIPMENT REQUIREMENTS

B5 Condition of Equipment

The Contractor-furnished helicopter, fuel servicing vehicle, and all other required equipment must be operable, free of damage, and in good repair. Aircraft systems and components must be free of leaks, except where specified by the manufacturer.

B5.1 Prior to inspection and acceptance, the Contractor must permanently repair or replace all windows and windshields that have been temporarily repaired (stop drilling is considered temporary). All windows and windshields must be maintained at all times and must be clean and free of scratches, cracks, crazing, distortion, repairs, or tinting which hinders visibility.

B5.2 The aircraft interior must be clean and neat with no unrepaired tears, rips, or other damage. The exterior finish, including the paint, must be clean, neat, and in good condition. Any corrosion must be within manufacturer or FAA acceptable limits.

B5.3 Lap belt and shoulder harness assemblies shall be in acceptable condition as determined by the Government. See the Unacceptable Lap Belt and Shoulder Harness Conditions Exhibit (see Section C) for examples of lap belt and shoulder harness conditions that are not acceptable.

B5.4 Military or other similar low visibility paint schemes are unacceptable. The Contracting Officer’s Technical Representative (COTR) may approve high visibility enhancements.

B6 Aircraft Equipment Requirements

The Contractor must provide one fully compliant helicopter that is equipped as shown below for each item:

B6.1 A complete set of current aeronautical charts covering the expected area of operations.

Note: Electronic flight bags are acceptable if authorized by the FAA in the company’s operation specifications.

B6.2 One digital hour meter installed in a location visible by the pilot and front seat observer while seated. The meter must be wired in series with a switch on the collective control, and a switch activated by engine or transmission oil pressure or by equivalent means, to record flight time only.

B6.3 Free air temperature gauge.

B6.4 One set of individual lap belts for each installed seat.

B6.5 Double strap shoulder harness with automatic or manual locking inertia reel for each front seat occupant. Shoulder straps and lap belts must fasten with one single-point metal-to-metal, quick-release mechanism. Heavy-duty (military-style) harnesses with fabric loop connecting the shoulder harness to the male portion of the lap belt buckle are acceptable.

B6.6 Shoulder harnesses equipped with inertia reel (either single-strap or double-strap) for each aft cabin occupant.

Shoulder harness straps and lap belts must fasten with a single-point, metal-to-metal, quick-release mechanism.

B6.7 Fire extinguisher(s), as required by 14 CFR 135, must be a handheld bottle, minimum 2-B:C rating, mounted and accessible to the flight crew while seated. (See the fire extinguisher maintenance instructions in Section B29.)

B6.8 Dual controls for initial pilot performance evaluation.

(May also be required for interim or recurrent pilot performance evaluations at the option of the Government.)

B6.9 Aircraft lighting for night operation in accordance with 14 CFR 91.205(c), including instrument lights.

B6.10 A strobe light (with either a white, or half-white/half-red lens) or a flashing LED (red or white), mounted on top of the aircraft or otherwise visible from above, with an independent activating switch. A red strobe or rotating beacon does not satisfy this requirement.

B6.11 High visibility, pulsating, forward-facing, conspicuity lighting.

B6.12 High visibility markings on main rotor blades as specified by the Acceptable Paint Schemes Exhibit.

B6.13 High-skid-type landing gear if manufactured for make and model.

B6.14 Personnel access steps for aircraft with a floor height greater than 18 inches to ensure safe entrance and exit from each door.

B6.15 Locking cap(s) on all fuel inlet ports.

B6.16 Cabin heater and window defogger.

B6.17 Wire strike protection system (mechanical).

Note: If manufactured for the make and model of helicopter.

B6.18 Main rotor brake.

B6.19 Reserved

B6.20 Reserved

B6.21 Cargo compartment, internal or external capable of accommodating 58-inch long shovels, rakes, and other tools as specified below:

For internal:

B6.21.1 15-cubic-foot baggage compartment within the aircraft fuselage specifically designed to carry cargo separate from the cabin.

Note: Requires rear bulkhead modification on some models of aircraft.

For external:

B6.21.2 Cargo basket. An externally side-mounted basket constructed with tubular frame and expanded metal incorporating a locking lid to secure cargo.

Note: AS350 aircraft must be equipped with a cargo basket such the Dart Heli-Utility basket (Minimum length of 89” with a 300 lb capacity) or equivalent.

All construction methods must be as prescribed by Advisory Circulars 43.13-1B and 43.13-2B or other FAA approval.

Note: Basket/rack must be quick attach/detach.

B6.22 Cargo restraint system for aircraft manufactured with a parcel/storage area behind the rear passenger seats.

B6.23 An accessory power source consisting of an MS 3112E-12-3S three-pin connector, accessible in the cabin. Pin B must be airframe ground; pin A must be +28VDC (for 28-volt aircraft); and pin C must be +14VDC (for 14-volt aircraft). The circuit must be protected by a 5-amp circuit protection.

B6.24 A first aid kit containing items specified in the First Aid and Survival Kits Exhibit (see Section C) must be carried aboard the aircraft on all flights.

B6.25 A survival kit containing items specified in First Aid and Survival Kits Exhibit (see Section C) must be carried aboard the aircraft on all flights and must be included in weight and balance/load calculations.

B6.26 A convex mirror for the pilot to observe the sling load.

B6.27 One keeperless cargo hook that may be loaded and locked in a single motion with one hand and is rated at the maximum lifting capacity of the aircraft. (See the cargo hook maintenance requirements in Section B29.)

B6.28 Cockpit-mounted external load indicator with readout of weight carried on the cargo hook.

B6.29 One collapsible, variable capacity water/retardant bucket. See the Water Bucket Use Procedures Exhibit (see Section C). The bucket must have a manufacturer's capacity adjustment commensurate with the maximum lifting capability (HOGE-J) of the contract aircraft at 5,000 feet pressure altitude (PA), 30˚ Celsius with a 200-pound pilot, 25-pound survival kit, and 1.5 total hours of fuel. The bucket must be capable of being operated with all increments of the longline; i.e., 50, 100, 150 feet.

B6.30 A second collapsible, variable capacity water/retardant bucket. See the Water Bucket Use Procedures Exhibit (see section C). The bucket must have a manufacturer's capacity adjustment commensurate with the maximum lifting capability (HOGE-J) of the contract aircraft at 7,000 feet PA, 25˚ Celsius with a 200-pound pilot, 25-pound survival kit, and

1.5 total hours of fuel. The bucket must also be capable of being operated with all increments of the longline; i.e., 50, 100, 150 feet.

Note: The bucket combinations provided in B6.29 and B6.30 must provide adjustments that allow the widest range of altitude/temperature combinations (subject to the limitations of the bucket manufacturer’s available sizes) for the maximum lifting capability of the helicopter beginning at 5,000 feet PA at 30˚ Celsius extending upward to 7,000 feet PA at 30˚ Celsius and above.

B6.31 A remote operating switch for the water/retardant bucket and/or remote hook clearly marked for "open" and "closed" and mounted on the collective control to avoid confusion with the airframe cargo hook release. The switch must be of a different design and must be mounted so as to not easily be confused with the RPM Control [Beep Range] switch.

B6.32 Part number MS 3101E-24-11S, nine-pin connector, for use as the power source for a helitorch or remote cargo hook. Pin D must be airframe ground. Pin E must be switched 28VDC, protected by a manually operable, 50-amp circuit breaker. The water bucket/tank open switch must also activate this circuit.

B6.32.1 A lanyard to support the connector and mounted within 12 inches of the cargo hook.

B6.32.2 This connector must have multiple circuit capacity sufficient to provide power and control for Contractor-furnished equipment. The longline remote hook, fixed tank, or water bucket must be wired through this connector. A list of water buckets with required pin wiring can be found in the USDA Forest Service/DOI OAS Drawing A-16 Exhibit (see Section C). Wiring diagrams for various equipment configurations are available from the U.S. Department of the Interior, Office of Aviation Services, 300 E. Mallard Drive, Suite 200, Boise, ID 83706, or USDA Forest Service, 3833 S. Development Avenue, Boise, ID 83705-5354.

B6.33 One remote cargo hook with related cabling and release system complying with the following specifications:

B6.33.1 Electrically activated remote cargo hook that may be loaded and locked in a single motion with one hand and that is rated at the maximum lifting capacity of the aircraft.

B6.33.2 The remote hook must be protected by a metal ring or cage that does not interfere with the use or function of the hook.

B6.33.3 Synthetic rope meeting the requirements of the Helicopter Synthetic Longline Requirements Exhibit (see Section C).

B6.33.4 The length of the rope must be readily adjustable from 50 to 150 feet in 50-foot increments.

B6.33.5 Electrical cables must be protected from pinching by hooks or shackles and from damage caused by stretching of the line. The electrical wire must be long enough at the aircraft cargo hook end to prevent a swinging load from unplugging the electrical connector.

B6.33.6 All fabrication and installation methods must comply with 14 CFR 133 and Advisory Circular 43.13–1B.

B6.33.7 Operating switch for the remote hook. (See B6.31 for specification. Only 1 switch required)

B6.34 Alaska specific equipment requirements. Refer to Alaska Supplement Exhibit (See Exhibit 12).

B6.34.1 The tundra pads and auxiliary fuel system will be inspected and must be together with the aircraft for the initial inspection and all subsequent contract renewal inspections.

B6.34.2 The FAA certification must be available at the time of agency inspection.

B7 Avionics Requirements

B7.1 General

All installed transceivers must be placarded with designations matching the transmitter/receiver controls on the installed audio control system(s)

B7.1.1 The Contractor must provide, install, and maintain the following systems in accordance with the manufacturer's specifications and the installation and maintenance standards of Section B7. Detailed avionics systems performance requirements are listed in Avionics Operational Test Standards (copies available upon request from OAS Avionics, or the most recent list may be found online at:

https://www nifc.gov/NIICD/docs/avionics/FSOAS A24F.p df

B7.2 Avionics Installation and Maintenance Standards

B7.2.1 Strict adherence to the recommendations in the following FAA Advisory Circulars is required: AC 43.13-1B Chapter 11, "Aircraft Electrical Systems," and Chapter 12, "Aircraft Avionics Systems”; AC 43.13-2B Chapter 1, "Structural Data," Chapter 2, "Communication, Navigation, and Emergency Locator Transmitter System Installations," and Chapter 3, "Antenna Installation."

B7.2.2 All avionics systems requiring an antenna must be installed with a properly matched, aircraft-certified antenna, unless otherwise specified. Antennas must be polarized as required by the avionics system and must have a voltage standing wave ratio (VSWR) of 3.0 to 1 or better.

B7.2.3 Although the contract aircraft may not be certified for flight under instrument flight rules (IFR), the aircraft's static pressure system, altimeter instrument system, and automatic pressure altitude reporting system must be maintained in accordance with the IFR requirements of 14 CFR Part 91.411 and inspected and tested every 24 calendar months, as specified by 14 CFR Part 43, appendices E and F.

B7.2.4 Transmitters shall not open squelch on, or interfere with, other AM or FM transceivers in the aircraft which are monitoring different frequencies. So-called “Transmit Interlock” functions shall not be used with communication transceivers.

B7.3 Communications Systems

B7.3.1 One automatic-fixed Emergency Locator Transmitter (ELT), certified under TSO-C126 (or newer) which must be installed in a conspicuous or marked location, and meet the same requirements as those detailed for airplanes in 14 CFR

91.207 (excluding section f). If not powered by its own, integral battery, the ELT remote switch/light must be powered by unswitched aircraft power. ELT antennas must be mounted externally to the aircraft unless installed in a location approved by the aircraft manufacturer. TSO-C126 and newer ELTs require documentation of current registration with the National Oceanic and Atmospheric Administration (NOAA), or the national civil aviation authority with which the aircraft is registered.

B7.3.2 Two panel-mounted VHF-AM (VHF-1, VHF-2) aeronautical transceivers, each with a minimum of 760 channels covering 118.000 to 136.975 MHz. The transceivers must have channels selectable in no greater than 25 kHz increments and a minimum of 5 watts carrier output power.

The transceivers’ operational controls must be mounted so they are readily visible and accessible to the pilot. Although not required by Federal Aviation Regulations, the aircraft’s radio call sign (normally the aircraft registration number) must be displayed on the instrument panel, in view of the flight crew.

B7.3.3 Two P25-compliant VHF-FM transceivers. Each transceiver (FM-1, FM-2), must provide selection of narrowband analog (12.5 kHz) or narrowband digital (12.5kHz) operation on each of a minimum of 100 channels. Each transceivers’ operational controls must be located and arranged so that the pilot and observer/copilot when seated, have full and unrestricted movement of each control without interference from clothing, the cockpit structure, or the flight controls.

B7.3.3.1 Each transceiver’s operational frequency range must include the band of 136.0000 MHz to 173.9975 MHz. The operator(s) must be able to program any usable channels within that band, along with any required CTCSS tones, National Access Codes (NAC’s), or Talk Group ID’s (TGID’s), while in flight. Each transceiver must also incorporate a separate, programmable GUARD receiver, with accompanying GUARD transmit capability. Unless instructed by the Government for use on a specific project, all frequencies programmed for use under this Contract must be in the narrowband analog mode.

B7.3.3.2 Carrier output power for each transceiver must be 10 watts nominal value (original design specification). Each transceiver must be capable of displaying receiver and transmitter operating frequency, alpha-numeric channel labels, and must provide both receiver and transmitter activation indicators for MAIN and GUARD. Simultaneous monitoring of both MAIN and GUARD receivers is required. Scanning of the GUARD frequency is not acceptable.

B7.3.3.3 Prior to acceptance under this contract, at least one transceiver must be programmed with the narrowband analog GUARD receive and transmit frequencies of 168.625 MHz, with a 110.9 Hz CTCSS tone on transmit only.

B7.3.3.4 The following VHF-FM aeronautical transceivers are known to meet the above requirements:

Technisonics: TDFM-136, TDFM-136A, TDFM-136/NV, TDFM-136A/NV, TDFM-136B, TDFM-136B/NV.

Cobham: (formerly NAT) NPX-136D-070.

B7.3.4 Provisions for auxiliary VHF-FM (AUX-FM) portable radio:

B7.3.4.1 Interface for installing and properly operating an auxiliary VHF-FM portable radio through the aircraft's audio control system(s). The interface must consist of the appro-priate wiring from the audio control system, terminated in an ITT/Cannon type MS3112E12-10S 10-pin connector conveniently located for use by the observer/copilot, and utilizing the contact assignments as specified by drawing FS/OAS A-17 in Exhibit 8.

B7.3.4.2 One weatherproof, external, broadband antenna covering the 150-174 MHz band, with associated RG58A/U

(or equivalent) coaxial cable and connector, terminated in a bulkhead-mounted, female BNC connector (type UG-290A), conveniently located for use by the observer/copilot adjacent to the above 10-pin connector (Comant model CI177 or equal).

B7.3.4.3 Mounting facilities for securely installing the auxiliary VHF-FM portable radio in the cockpit in accordance with the FAA AC 43.13-2B specifications. Locate and arrange the mounting facilities so that a seated observer/copilot has full and unrestricted movement of the radio's controls, without interference from the 18-inch adapter cable, clothing, cockpit structure, or flight controls.

B7.3.4.4 Positive-polarity microphone excitation voltage provided to the AUX-FM system from the aircraft DC power system through a suitable resistor network. A blocking capacitor must be provided to prevent the portable radio microphone excitation voltage from entering the system.

Sidetone for the AUX-FM must also be provided (NAT model AA34-300, Premier model PA-34, or equivalent).

B7.3.4.5 In lieu of the above AUX-FM requirements, the Contractor may substitute an additional VHF-FM aeronautical transceiver (FM-3) which meets the requirements for the VHF-FM aeronautical transceiver(s) as detailed above.

B7.3.5 One satellite-based aircraft tracking hardware compatible with the government’s Automated Flight Following (AFF) Program (https://aff.gov). Not all available satellite based tracking systems are compatible with the Government’s AFF Program, nor meets AFF’s requirements. The contractor must ensure that the aircraft hardware offered is compatible with AFF. For questions about current compatibility requirements contact the AFF Program Manager listed under contacts at https://www.aff.gov.

B7.3.5.1 The AFF aircraft hardware must be powered by the aircraft’s electrical system, installed per the manufacturer’s installation manual, and operational in all phases of flight. AFF aircraft hardware must utilize as a minimum: Satellite communications, an externally or internally mounted antenna, provide data to the Government’s AFF viewing software, use aircraft power via a dedicated circuit breaker for power protection, and be mounted so as to not endanger any occupant from AFF aircraft hardware during periods of turbulence.

Antennas should be placed where they have the best view of the overhead sky as possible. Externally mounted antennas are recommended to improve system performance. Any visual indicators for remotely installed units must be mounted so that they can be easily viewed by the pilot.

B7.3.5.2 AFF communications must be fully operational in all 50 states. Contractors working in dispatched to the State of Alaska, Southern Canada, or Western Canada must have an AFF system capable of being tracked in these locations at all times. Not all manufacturers’ AFF equipment communication links will operate effectively in all geographic areas.

B7.3.5.3 The contractor must maintain a subscription service through the AFF aircraft hardware provider allowing AFF position reporting for satellite tracking via the Government AFF viewing software. The position-reporting interval must be every two minutes while the aircraft is in flight. The contractor must register their AFF aircraft hardware with the Government through https://www.aff.gov providing: complete tail number;

manufacturer and serial number of the AFF transceiver; aircraft make and model; and contractor contact information. If the contractor relocates previously registered AFF aircraft hardware into another aircraft, then the contractor must contact the government’s AFF Program making the appropriate changes prior to aircraft use. In all cases, the contractor must ensure that the correct aircraft information is indicated within AFF. The contractor must contact the Government of system changes, scheduled maintenance, and planned service outages

B7.3.5.4 Registration contact information, a web accessible feedback form, and additional information is available at:

https://www.aff.gov.

B7.3.5.5 Prior to the aircraft’s annual contract inspection, the contractor must ensure compliance with all AFF systems requirements. The contractor must additionally perform an operational check of the system. As a minimum, the operational check must consist of confirming the aircraft being tested is displayed in AFF (indicating it is currently transmitting data to AFF) and that all information displayed in AFF is current. A username and password are required to access AFF. Log on to the AFF website at https://www.aff.gov to request a username and password.

B7.3.5.6 If AFF becomes inoperable/unreliable the aircraft may, at the discretion of the Government, remain available for service utilizing radio/voice system for flight following. The contractor will return the AFF system to full operational capability within 72 hours after the inoperative/unreliable unit is first discovered as defective.

B7.3.5.7 This clause incorporates Specification Section Supplement available at:

https://www.aff.gov/documents/Specification Section Supple ment.pdf with the same force and affect as if they were presented as full text herein.

B7.4 Navigational Systems

B7.4.1 One permanently installed, panel-mounted global positioning system (GPS-1) utilizing an approved, fixed external aircraft antenna and powered by the aircraft electrical system or an aviation portable GPS unit (Garmin GPSMap 296/396/496 or equivalent) provided the portable unit is securely mounted, is equipped with a remote (i.e., not part of the GPS unit) antenna, and presents information from an overhead orientation (not a drive-along-the-road type), and is powered by the aircraft electrical system. The GPS (permanently installed or portable) must utilize the WGS-84 datum and reference latitude and longitude coordinates in the degrees/minutes/decimal minutes (DM) mode for aircraft positioning. The GPS navigation database must be updated annually covering the geographic areas where the aircraft will operate. The primary GPS (or a second GPS at the co-pilot position) must also have near real-time weather downlink capability.

B7.5 Audio Systems

B7.5.1 Two separate audio control systems (which may be combined in a single unit) for the pilot and observer/co-pilot to select receiver audio outputs and transmitter microphone/push to talk (PTT) audio inputs for all installed radios and public address (PA) systems. Each system must also allow the pilot and observer/copilot to independently adjust both the intercommunications system (ICS) and the receiver audio output levels.

B7.5.1.1 Transmitter selection and operation. Separate transmitter selection controls must be provided for both the pilot’s and observer/copilot’s microphone/PTT inputs. The system must be configured so the pilot and observer/copilot may each simultaneously select and utilize a different transmitter (or PA system when installed) via their respective microphone/PTT. Whenever a transmitter is selected, the companion receiver audio must automatically be selected for the corresponding earphone. Transmitter sidetone audio must be provided for the user as well as for cross-monitoring via the corresponding receiver selection switch on the other audio control system.

B7.5.1.1.1 The two aft cabin exit positions must be equipped to transmit on the radio(s). Whenever a radio (or PA, when so equipped) microphone input is selected at the observer/copilot's audio control panel, the aft cabin passengers' radio microphone inputs must automatically be connected to the same radio, and they must then be capable of transmitting on that radio via their respective radio transmit PTT switches.

B7.5.1.2 Receiver selection and operation. Separate controls must be provided for both pilot and observer/copilot to select audio from one or any combination of available receivers.

The ICS-equipped aft passenger positions must monitor the receiver(s) as selected by the observer/copilot. The receiver audio output must be free of excessive distortion, hum, noise, and crosstalk, and must be amplified sufficiently to facilitate ease of use in a noisy cockpit/cabin environment.

B7.5.1.3 The audio system(s) controls must be located and arranged so that both the pilot and observer/copilot, when seated, have full movement of their respective controls without interference from their clothing, the cockpit structure, or the flight controls. Labeling and marking of controls must be clear, understandable, legible, and permanent. Electronic label maker marking is acceptable.

B7.5.2 An ICS for the pilot, observer/copilot, and all aft cabin positions. ICS audio must mix with, but not mute, selected receiver audio. An ICS audio level control must be provided for each position above. Adjustment of the ICS audio level at any position must not affect the level at any other position. A "hot mic" capability, controlled via an activation switch or voice activation (VOX), must be provided for the pilot and copilot/observer positions. ICS sidetone audio must be provided for the earphones corresponding with the microphone in use. The ICS audio output must be free of excessive distortion, hum, noise, and crosstalk and must be amplified sufficiently to facilitate ease of use in a noisy cockpit/cabin environment.

B7.5.3 Earphones, microphones, PTT’s, and jacks designed for operation with 600-ohm earphones and carbon-equivalent, noise-canceling boom type microphones (Gentex electret type model 5060-2, military dynamic type M-87/AIC with type CE-100 TR preamplifier, or equivalent) with U-174/U (single/male) type connector plug. The pilot position only may be configured for low impedance (dynamic) operation.

B7.5.3.1 A single U-92A/U type connector jack, which will accept a U-174/U type plug, and provide the ICS and radio functions as specified above, must be furnished at each required station.

B7.5.3.2 Separate PTT switches for radio transmitter and ICS microphone operation must be provided at the pilot, observer/copilot, and any other positions required above to be furnished with both radio transmitter and ICS operation. The pilot's PTT switches must be mounted on the cyclic control.

The observer/copilot's and any other required position’s PTT switches must be mounted on the cord to the earphone/microphone connector. The aft cabin positions must be furnished with cord-mounted ICS PTT switches.

B7.6 Other Avionics

B7.6.1 One air traffic control (ATC) transponder and altitude reporting system meeting the requirements of 14 CFR Part

91.215 (a) and (b), and inspected and tested every 24 months in accordance with 14 CFR 91.413.

B7.6.2 One APCO Project 25 compliant (P25) VHF-FM "multi-mode" two-way mobile radio, with a matched broad-band antenna, must be mounted in the fuel-servicing vehicle.

The radio's operational bandwidth must include the 150 MHz to 174 MHz frequency band, with user-programmable (in the field) channels. Selection of narrowband (12.5 kHz) analog, or digital (12.5 kHz) spacing is required on each channel. The radio must be frequency-synthesized, equipped with the lowest 32 CTCSS sub-audible tones, and must develop a minimum of 30 watts carrier output power. Use of appropriate portable VHF-FM radios with suitable output power booster units is permissible.

The following radio models are known to meet the above requirements:

Datron G25RMV100, G25RMV110, G25ASU001 Kenwood TK-5710, TK-5720 Midland STM-1050B, STM-1055B, STM-1115B Relm(BK) Radio: DMH5992 with Smartmic, DMH5992X HP with Smartmic Relm: KNG-M150

Note: See http://www.nifc.gov/NIICD/docs/approved_radios.pdf for a complete, current listing of approved radios.

B7.6.3 One APCO Project 25 compliant (P25) VHF-FM two-way portable radio for pilot call-back, operating in the 150 MHz to 174 MHz frequency band, frequency-synthesized, CTCSS 32 sub-audible tone capable, user programmable in the field, with a minimum of 5 watts carrier output power, must be furnished for use by the pilot-in-command (PIC).

Selection of wideband (25.0 kHz) analog, narrowband (12.5 kHz) analog, or digital (12.5kHz) spacing is required on each channel.

The following radio models are known to meet the above requirements:

Datron: Guardian G25PRV100 Midland: STP105B Motorola: XTS 2500 & XTS 5000*

* only w/R.15.00.05 or newer software Relm(BK): DHP5102X, DPHX5102X Relm: KNG-P150, KNG-P150S, KNG2-P150 Thales(Racal): 25 PRC-6894

Note: See http://www.nifc.gov/NIICD/docs/approved radios.pdf for a complete, current listing of approved radios.

B7.6.4 The Contractor must furnish a cellular telephone for use by the PIC. The cellular telephone must be provided with service to the area of the contiguous 48 States. Each cellular telephone must be equipped with both 110VAC and 12VDC adapter cord assemblies for charging use. The Contractor must provide the number of the cellular telephone to Government personnel when requested.

B7.6.5 Automatic Dependent Surveillance – Broadcast (ADS-B) All aircraft must be equipped to meet the ADS-B OUT requirements of 14 CFR 91.225. ADS-B OUT systems must be approved to either TSO-C154c (978MHz Universal Access Transceiver [UAT]) or TSO-C166b (1090MHz Extended Squitter [1090ES]). Aircraft operating outside of the United States must be equipped with systems approved to TSO-C166b.

B7.6.6 Each aircraft must be equipped to meet the Radar Altimeter requirements of 14 CFR 135.160, where applicable.

B8 Fuel Servicing Vehicle Equipment Requirements (Required for Lower 48 States Operations Only)

B8.1 General.

B8.1.1 Fuel servicing vehicles must meet 49 CFR requirements.

B8.1.2 The Contractor must provide one fuel servicing vehicle (truck and trailer combination is acceptable) for each line item (aircraft) awarded. The vehicle will be stationed at the designated base, unless dispatched by the Government to other locations. Vehicle specifications follow:

B8.1.2.1 The fuel servicing vehicle must be a four-wheel drive truck…