SLACKS POT.pdf

SLACKS, WOMAN'S, SERVICE, UNBELTED, SHALL BE MADE IN ACCORDANCE WITH NCTRF PD 07-06A DATED 12

DECEMBER 2006

PATTERN DATE: 4 FEBRUARY 2010

STANDARD SAMPLE OF CLOTH, 75%/POLYESTER/25%WOOL TROPICAL, BLUE SHADE 3346, IS AVAILABLE AND APPLICABLE FOR SHADE AND COLORFASTNESS TO LIGHT, PERSPIRATION, LAUNDERING, DRY CLEANING AND

CROCKING UNDER PIECE NO. 10163

CLOTH MATERIAL TO BE IN CONFORMANCE WITH NCTRF PD 04-06

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY

REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

CLOTH, TROPICAL: POLYESTER AND WOOL, CLASS 1 and 2

ADDITIONAL INFORMATION FOR NTCRF PD 04-06, CLASS 1:

STANDARD SAMPLE FOR CLOTH, TROPICAL: POLYESTER AND WOOL, BLUE 3346 CONFORMING TO NCTRF PD 04-06, IS AVAILABLE ON ROLL NO. 10163, AND APPLICABLE FOR SHADE, FINISH AND COLORFASTNESS.

ADDITIONAL INFORMATION FOR NTCRF PD 04-06, CLASS 2:

STANDARD SAMPLE FOR CLOTH, TROPICAL: POLYESTER AND WOOL, KHAKI 3729 CONFORMING TO NCTRF PD 04-06, IS AVAILABLE ON ROLL NO. 06081, AND APPLICABLE FOR SHADE, FINISH AND COLORFASTNESS.

RECOMMEND 100 PERCENT SHADE VERIFICATION FOR EACH LOT PRESENTED TO GOVERNMENT FOR LIFE OF THE ITEM. INTERIM CHANGES TO NCTRF PD 07-06A . PAGE 4 . Para. 3.2.1.1. line 3, after "finished waistband."

add "As an alternate, in lieu of using a top stop, the chain shall continue into the waistband and be caught in the bottom row of stitching of the waistband." . Para. 3.2.1.4. delete and substitute: "3.2.1.4. Tummy tamer.

The tummy tamer shall be constructed from the pocketing material and shall be single needle set to the center of the front matching the raw edge of front rise before fly assembly, waistband, and folded edge of pocket bag. The pocket bags shall not be distorted. The bottom edge of the tummy tamer shall be overedged.". . Paragraph 3.2.1.5, at end of paragraph add, "The inside bottom shall be clean finished, which may be achieved by binding the edge with a suitable binding fabric or turning up and single needle stitching.

Para. 3.2.1.7. Line 2, delete "extending from the top of the waistband" and substitute "extending from the bottom of the waistband seam." . PAGE 5 . Para. 3.3.3. line 4, after "polyester/nylon," add "or polyester". At end of paragraph add "The color of the fusible interlining shall be black, charcoal or dark gray.". . PAGE 6 .

Para. 3.3.3.1. Table I, under "Stiffness", delete "After 25 launderings" and substitute, "After 10 launderings".

Under "Peel Strength", delete "After 25 launderings" and substitute "After 10 launderings". Under "Appearance", delete "After 25 launderings" and substitute "After 10 launderings". . Para. 3.3.8. delete in its entirety and substitute: "3.3.8. Silicone bead. The silicone bead used in the permanent creasing process shall be a nonstaining adhesive. The silicone bead shall show no evidence of flaking, decomposition, failure to retain crease, cracking, staining or strike back onto the face of the material, or increased stiffness when tested for resistance to dry heat and perchloroethylene solvent when tested in accordance with 4.4.1.1. The permanent creases in the finished slacks shall have a minimum rating of "good". . Para. 3.3.9.1, line 3, delete "1/2 inch from the bottom right edge of the right side pocketing" and substitute "stitched to the bottom of the right side pocketing". . Para. 3.3.5, delete and substitute: "3.3.5. Slide fastener. The slide fastener shall be polyester or nylon continuous monofilament chain, with automatic locking short tab pull slider, conforming to Type I, Style 4, Commercial size 3 of A-A-55634. All slide fasteners shall have a staple bottom stop and 7/16 inch width tape. The color of the tape and all components shall be black.". . PAGE 8 . Para 3.3.9.3, line 3, delete "3-3/8" and substitute "3-7/8." . Insert new paragraph, "3.3.9.4. DSCP Exclusive embroidered label. Each pair of slacks shall have a DSCP/Contactor embroidered label with the Contractors name below it. The label shall be sewn to the bottom of the waistband opposite the size label, two inches off center back. . Page 9 . Para 3.4.1. Table II after "LTFLYLININ Left Fly Lining 1 Pocketing" insert "1/". After table insert "1/ As an alternate, the Left Fly Lining may be cut from the Basic Material, in 3.3.1" . Para 3.4.2. line 7, delete "1/8" and substitute "1/4". Line 9, after "edge" delete extra period. . Page 12 . 4.4.1. Table VI, under "Component" delete "Permanent creases" and substitute "Silicone bead". . Page 13 . Para 4.4.1.1.2.

Permanency of crease test., Line 2, after "wetting agent" insert"(see 6.7)". . Para 4.4.2. Table VII, under "Stiffness", delete "After 25 launderings" and substitute "After 10 launderings". Under "Peel strength", delete "After 25 launderings" and substitute "After 10 launderings". Under "Appearance", delete "after 25 launderings" and substitute "after 10 launderings". . Para 4.4.4. Table VII, footnote 1/, line 2, delete "25th" and substitute "10th" . Page 15 . 4.4.4. Table VIII add new defect: "d. Zipper. Not caught in finished waistband. -Point value 3." . Page 16 . Insert new paragraph "6.7 Wetting agents. Woolite(Registered trademark) or liquid laundry soap are appropriate wetting agents". .

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE

FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

ADDITIONAL INFORMATION FOR MIL-STD-656:

INTERIM CHANGES TO MIL-STD-656C

PAGE 18, DEFECT XV. POCKET OR FLAPS, S.

HIP POCKET: ADD NEW DEFECT:

"3. CORD (WELTS) OUT OF HORIZONTAL ALIGNMENT

WITH WAISTBAND WHEN MEASURED FROM BOTTOM OF

WAISTBAND TO TOP CORNERS OF WELT BY:

. D S U

-MORE THAN 1/2 INCH * 3 2

-MORE THAN 1/4 UP TO 1/2 INCH 3 3 2

-UP TO 1/8 MORE 1/4 INCH 2 2 1

INTERIM CHANGES TO MIL-STD-656C:

PAGE 5, TABLE I DELETE IN ITS ENTIRETY AND

SUBSTITUTE "TABLE I SAMPLING PROVISIONS FOR END

ITEM VISUAL EXAMINATION OF DRESS (D) SLACKS:

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 &1 PT

. DEFECTS DEFECTS

UP THRU 90 20 3 PT 6 PT

91 - 150 32 5 PT 9 PT

151 - 280 50 7 PT 13 PT

281 - 500 80 9 PT 17 PT

501 - 1200 125 14 PT 25 PT

1201 - 3200 200 18 PT 33 PT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

3201 - 10,000 315 24 PT 48 PT

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

10,001 - 35,000 500 35 PT 72 PT

35,001 AND OVER 800 55 PT 110 PT

TIGHTENED INSPECTION:

UP THRU 150 32 2 PT 5 PT

151 - 280 50 3 PT 7 PT

281 - 500 80 5 PT 11 PT

501 - 1200 125 9 PT 17 PT

1201 - 3200 200 13 PT 26 PT

3201 - 10,000 315 20 PT 39 PT

10,001 - 35,000 500 30 PT 59 PT

35,001 AND OVER 800 45 PT 89 PT

REDUCED INSPECTION:

UP THRU 280 20 2-6 PT 11 PT

281 - 500 32 3-9 PT 15 PT

501 - 1200 50 5-10 PT 18 PT

1201 - 3200 80 8-13 PT 24 PT

3201 - 10,000 125 12-17 PT 28 PT

10,001 - 35,000 200 17-21 PT 33 PT

35, 001 AND OVER 315 23-29 PT 47 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE II SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF SEMI-DERSS (SD) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2.&1 PT

. DEFECTS DEFECTS

UP THRU 500 50 7 PT 14 PT

501 THRU 1200 80 9 PT 20 PT

1201 THRU 3200 125 14 PT 26 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 THRU 35,000 315 27 PT 57 PT

35,001 AND OVER 500 41 PT 85 PT

TIGHTENED INSPECTION:

UP THRU 500 50 3 PT 10 PT

501 THRU 1200 80 5 PT 15 PT

1201 THRU 3200 125 8 PT 23 PT

3201 THRU 10,000 200 12 PT 34 PT

10,001 THRU 35,000 315 19 PT 52 PT

35,001 AND OVER 500 27 PT 78 PT

REDUCED INSPECTION:

UP THRU 1200 32 3-8 PT 15 PT

1200 THRU 3200 50 5-9 PT 18 PT

3201 THRU 10,000 80 8-12 PT 24 PT

10,001 THRU 35,000 125 11-15 PT 31 PT

35,001 AND OVER 200 15-53 PT 43 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE III DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE III SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF UTILITY (U) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 & 1 PT

. DEFECTS DEFECTS

UP THRU 500 50 9 PT 17 PT

501 THRU 1200 80 13 PT 20 PT

1201 THRU 3200 125 18 PT 29 PT

3201 THRU 10,000 200 25 PT 42 PT

10,001 AND OVER 315 39 PT 62 PT

TIGHTENED INSPECTION:

UP THRU 500 50 5 PT 11 PT

501 THRU 1200 80 8 PT 17 PT

1201 THRU 3200 125 12 PT 25 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 AND OVER 315 27 PT 57 PT

REDUCED INSPECTION:

UP THRU 1200 32 5-9 PT 16 PT

1201 THRU 3200 50 8-12 PT 20 PT

3201 THRU 10,000 80 11-14 PT 25 PT

10,001 AND OVER 125 15-19 PT 29 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

PAGE 20, UNDER XX LABEL ADD THE FOLLOWING:

D. BAR CODE LABEL/TAG

DEFECT POINT VALUE

. D SD U

1. BAR CODE OMITTED OR NOT

. READABLE BY SCANNER. 1 1 1

2. HUMAN READABLE INTERPRETATION

. (HRI) OMITTED OR

. ILLEGIBLE 1 1 1

3. NOT VISIBLE ON FOLDED,

. PACKAGED ITEM. 1 1 1

4. CAUSES DAMAGE TO THE

. ITEM. 3 3 3".

(Ref. T0320)

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34

6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2 MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR

SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF

MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN.

NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED

INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL

BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

Examination of packaging requirements. An examination shall be made to determine that packaging, packing, and marking comply with MIL-STD-129, MIL-STD-2073-1D, ASTM D5118, and ASTM D1974. Defects shall be scored in accordance with the list below. The sample unit shall be one shipping container fully prepared for delivery. The lot size shall be the number of shipping containers in the end item inspection lot.

The inspection level shall be S-2 and the acceptable quality level (AQL) shall be 2.5, expressed in term of defects per hundred units.

Examine Defect

Marking Omitted,incorrect,illegible,of improper (Exterior and size, location,sequence, or method of interior) application.

Materials Any component missing, damaged, or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of flags, loose strapping, imprper taping, inadequate stapling, bulged or distorted containers.

Content Number of items per shipping container is more or less than required. Size shown on one or more items not as specified on shipping container. 1/

1/ For this defect, one item from each shipping container in the sample shall be examined. Nexcom Labeling: Each pair of slacks shall have a Joker Label sewn onto the waistband. The label shall fold over the waistband, centered between the second and third belt loops on left side of the slacks. The label shall have readable universal product code (UPC). The slack size, in 14 point bold font, shall be printed on the label so that it will be readable from the top of the waistband. "Athletic" or "Classic" will be clearly printed on the label. Suggested Source for Silicone creasing: Supercrease, Inc (formerly Lintrak) 7454 Yonie Ct Las Vegas, NV 89117-2161 Phone: (310) 994-6488 Toll free: (702) 500-0145 Email: chris@supercrease.com