SATPC0038368 Tab 04 4 SOW Rev_Redacted.pdf
PDF 139 KB Posted
- Attached to
- Hydraulic Compression Press, G30H-15-CX Federal contract opportunity
- Solicitation number
- 80NSSC25903222Q
About this file
This Statement of Work (SOW) details NASA Glenn Research Center's requirement for a Wabash G30H-15-CX Genesis Series Compression Press for the composites processing lab. The procurement is intended to replicate existing press capabilities, supporting multiple programs within STMD and ARMD, with the goal of increasing manufacturing efficiency. The press must meet specific technical specifications including a maximum operating temperature of 800°F, 5-30 ton adjustable compression force, 15" heated/cooled platens, and a self-contained hydraulic system with dual gear pumps and water-cooled heat exchanger.
The control system requires a NEMA-rated electrical enclosure with an Allen Bradley MicroLogix 1400 programmable controller, 4" PanelView 800 color touch screen, two-hand "anti-tie-down" cycle initiation circuit, proximity switches, and 460/3/60 supply voltage. The solicitation is set aside for small businesses, with the procurement specifically seeking a brand-name Wabash G30H-15-CX Genesis Series Hydraulic Compression Press. Press delivery will be coordinated with the designated point of contact to allow time for the current press to be removed.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| Vendor Questions and Response for 80NSSC25903222Q.pdf | ||
| SATPC0038368 Tab 10 BNJ_Redacted.pdf | ||
| SATPC0038368 Tab 10 RFQ Open Market.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Statement of Work- Hydraulic Press
The composites processing lab at NASA Glenn Research Center uses hydraulic presses to fabricate composite parts in support of mul�ple programs within STMD and ARMD. An addi�onal hydraulic press is required to meet the schedule and milestones of the project that are supported. This procurement is intended to replicate the current capabili�es in the lab to enable opera�on of both presses and increase manufacturing efficiency.
The below specifica�ons shall be met to replicate the current press performance.
Press: Wabash G30H-15-CX, Genesis Series Compression Press.
Temperature:
• Maximum opera�ng temperature of at least 800oF
Clamp:
• 5 - 30 ton compression force (adjustable)
• 15" L-R x 15" F-B fully guided heated/cooled platens
• Solid state relays including over temperature protec�on
• Insula�on between platen and bolster
• Perimeter insula�on
• 1/16 DIN digital temperature controllers
• One zone of temperature control per platen
• Single opening with:
• 6" – 12" open daylight (adjustable)
• 0" – 6" closed daylight (shut height)
• Factory set daylight @ 6"
• 5" bore JIC style clamp cylinder (develops maximum clamping force at 3,055 psi)
• 6" stroke
• 42" lower platen opera�ng height (approximate)
• Built-in li� truck tubes
Add op�on for pressing speed control
Hydraulic System
• Self-contained hydraulic system, including:
• Reservoir with gauge for oil level and temperature indica�on
• Dual gear pump system with energy-efficient TEFC motor
• Water-cooled heat exchanger
• 70 IPM closing speed
• 5 IPM pressing speed
• 75 IPM opening speed
Control System
• NEMA-rated electrical control enclosure, including:
• Allen Bradley MicroLogix 1400 programmable controller with 4" PanelView 800 color touch screen operator interface
• Cycle counter through PLC
• Opera�ng butons, including two-hand "an�-�e-down" circuit for cycle ini�a�on
• Indica�ng lights
• Proximity switches to control "slow close" posi�on and "cycle reset"
• Clamp pressure relief valve and gauge
• 460/3/60 supply voltage
• Non-fused disconnect
Press delivery shall be coordinated with POC iden�fied below to allow �me for current press to be removed.
File details come from the government source that posted it. Updated .